Search Documents

By H. A. Hancock, L. M. Pidgeon

Equilibrium carbon monoxide pressures were measured over the reaction between chromium oxide and a number of solid ferrochromium alloys in the composition range 0.4 to 4.8 pct C and 0 to 49 pct Fe. Measurements were also made for the carbides Cr23C6 and Cr7C3 which agreed well with previous investigations. Between 1050°and 1400°C the pvessures varied from 0.1 to 56 mm and increased markedly with the iron and carbon contents of the alloys. The data were used to estimate the activity of carbon in the alloys and to calculate the equilibrium conditions for the decarburization of a useful range of ferrochromium alloys. WHEN ferrochromium is produced by the reduction of chromite with carbon in an electric arc furnace it invariably contains up to 10 wt pct C. For many purposes such as the production of stainless steel, it is necessary that the carbon content be as low as from 0.02 to 0.05 pct. Thus an important part of the ferrochromium industry consists of the production of low carbon ferrochromium. The classical Bessemer steelmaking technique cannot be used to oxidize low carbon contents in chromium and ferrochromium alloys without also oxidizing the chromium. Recently a new commercial process2-4 has been introduced for oxidizing carbon from high chromium content alloys which consists of heating the solid alloy with such oxidizing agents as Cr2O3, Fe2O3, or SiO2 in a retort at reduced pressures. By maintaining the carbon monoxide pressure below the equilibrium value for the system, the carbon can be removed as carbon monoxide without oxidizing the chromium. The equilibrium conditions for the decarburization of solid chromium carbon alloys have been determined by Boericke5 who measured the carbon monoxide pressure over the reaction between the various chromium carbides and chromium oxide. A typical reaction is shown below. Cr23C6 + 2Cr2O3 =u 27Cr + 6CO [1] These values are not applicable to the decarburization of commercial ferrochromium alloys which invariably contain major amounts of iron. The present investigation was therefore undertaken to measure the change in the equilibrium carbon monoxide pressure brought about by additions of iron to the Cr-C-0 system, thus extending the work of Boericke into the region of the production of low carbon ferrochromium. MATERIALS AND METHOD Materials. Measurements were made on two carbides of chromium, Cr233C6 and Cr7C3, and fifteen Fe-Cr-C alloys. The chromium carbides were made

Jan 1, 1963

By P. R. Kalischer

IN the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more components that tend to form very stable oxides. Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others. In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken. If, however, it is required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible. Since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides. For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets. All of the pertinent properties of the magnets could be accurately and delicately measured by density measurements and magnetic tests of sufficient scope to give a complete demagnetization curve. From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material. Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties. NATURE AND REMOVAL OF SURFACE BARRIERS The early work of the present investigation was based upon published processes.* In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 per cent Fe, 50 per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200°C. or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics. However, this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable. In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen. Both the iron and nickel powders sintered

Jan 1, 1941

By Ralph Hultgren, Bernard York, David W. Mitchell

It is a well-known fact that magnesium-alloy castings are apt to be coarse grained if the melt is not superheated several hundred degrees above the melting point before casting. (The casting temperature varies according to the shape of the mold. A typical casting temperature is perhaps 1400°F.) British practice is to heat to 900°C. (1650°°F.) for 15 min., cool rapidly to casting temperature, and cast.1 In Germany superheating is carried out at 850° to 900°C. (1560° to 1650°F.) depending on the amount of scrap used. It is stated that further refinement will be obtained by prolonging the period of superheating or by increasing the superheat temperature to 950°C. (1740°F.).2 In the United States superheating is carried out at i600° to 1700°F. (871° to 927°C.), perhaps even higher in some places. It is stated that superheating effects are found as low as 1500°F. (816°C.), but several hours are required.3 These commercial treatments lead to grain sizes in sand castings that may vary from 4 to 8 grains per sq. mm.§ in heavy sections and from 60 to l00 in 3-in sections to perhaps 380 in thin sections. It is also generally known that the refining effect of superheating is lost if the melt is held for some time at lower temperatures before casting. Aside from these very qualitative statements, there is little to be found in the literature as to the effect of temperature and time of superheat on the final grain size. Because of the uncertainty of these factors, the Office of Production Research and Development of the War Production Board placed a research contract with the University of California, supervised by the War Metallurgy Committee. This research, which was done under the "Restricted" Project NRC-550, is the basis of this paper, which has been released for publication by the O.P.R.D. The material studied was an alloy prepared from carbothermic magnesium. The temperatures required for grain refinement proved to be widely different from those used in practice, as described in the statements in the first paragraph. This difference is attributed to the fact that the magnesium in the specimens was of carbothermic origin instead of the electrolytic magnesium in common use. MATERIALS AND METHODS The magnesium alloy studied was one of the most popular sand-casting alloys, with a nominal composition of 9 per cent aluminum, 2 per cent zinc, and 0.r per cent (minimum) manganese and the balance magnesium. This is designated

Jan 1, 1945

By William J. McCaughey, Richard L. Barrett

For sixty years—in fact, ever since the inception of the basic steelmaking process —basic slags have been the subject of study by chemists, metallurgists and petrog-raphers! with the purpose of providing a better understanding of the reactions between the slag and the metal during the refining process. The result of this work and of the researches of mineralogists and physical chemists into the chemistry of oxide systems is a considerable body of literature dealing not only with slags themselves but with equilibrium relationships in systems synthesized from pure components. Since any actual slag is a multicom-ponent system more complex than any yet worked out in the laboratory, a complete solution to the problem is still far away. The writers have recently published a paper1 which they believe sheds light on the role of the slag in the elimination of phosphorus and it is the purpose of the present paper to discuss the metallurgical applications of that work. Since the pioneer investigations on the constitution of basic slags carried on by Stead and Risdale, Carnot and Richards, Hilgenstock and others in the I88o's, a considerable body of literature on this subject has appeared. Many of the more important of these papers were summarized in the previous paper,l therefore they will not be reviewed here. PetRographic Study The present writers have had occasion, over a period of years, to examine petro-graphically a great number of basic steel-making slags having a very wide range of chemical compositions and made under various conditions of operating practice. Although certain of these slags exhibit some unusual features, it is a remarkable fact that the great majority of mature slags show certain typical characteristics, which persist throughout the wide range of chemical compositions. The typical mature slag usually appears under the microscope to consist of two phases. The phase of primary crystallization is light colored and doubly refracting. If separated mechanically and subjected to chemical analysis, it is found to consist essentially of SiO2, CaO, and P2O6. Sometimes, although not usually, two such silicate-phosphate phases are found. The other conspicuous phase is dark in color and optically isotropic, and occurs as the interstitial material between the grains of the light colored phase. This dark colored interstitial phase when analyzed is found to consist essentially of FeO, Fe2O3, MnO, and MgO. In some 'lags high in iron oxide, particularly those from low-carbon heats, dicalcium ferrite is found. This phase is dark reddish brown in color and anisotropic.

Jan 1, 1944

By T. A. Dungan

The thermal processes for the production of metallic magnesium can be divided into two general classifications, the direct reduction of magnesia with carbon and the indirect reduction of compounds of magnesium by reducing agents that are themselves products of carbon reduction. The latter are so chosen as to cause reduction of magnesium compounds wherein only the magnesium is liberated in the vapor phase. Reducing agents used are: calcium carbide, silicon carbide, silicon, aluminum, various silicides or combinations of calcium, aluminum, silicon in iron. All of these are products of highly endothermic reactions and, with the exception of scrap aluminum, can be produced in an open, submerged arc furnace; that is, the arc is covered only by the charge itself. The more investment in energy required to prepare such a reducing agent, the less is the energy required in the subsequent step to reduce the magnesium compound to the metal. It is impossible, however, to avoid the laws of thermodynamics, no matter how much circumambulation is resorted to in the preparation of successively more powerful reducing agents. Since each such step carries forward its own inefficiencies, it appears evident that the ultimate status of such processes is dependent upon the development of by-products. The direct reduction of magnesium oxide by carbon has a decided appeal to both the scientist and the industrialist. The successful production of the carbo-thermic plant at Permanente is a significant fact in the substantiation of this concept. Like most developments, however, the history of carbon reduction of magnesia is not one of triumph after triumph, or immediate heady success to the investigators. It is understood that one of the early investigators conducted an experiment wherein he placed carbon and magnesia in one end of an evacuated tube and managed to heat this end to a temperature high enough that magnesia and carbon deposited at the other end of the tube. The charge, unreduced, appeared to have been completely transported from the hot to the cold end of the tube. This raised doubt for some time as to whether magnesia could be reduced at all with carbon. It was correctly suspected, however, that the magnesia was in fact reduced and the resultant magnesium vapor and carbon monoxide reacted upon one another upon reduction in temperature to reform the starting ingredients. Attempts were then made to dilute the two vapors by passing a considerable stream of hydrogen through an arc furnace charged with magnesia and carbon. Thus by dilution of the products it was' expected to obtain metallic magnesium. The results were positive and metallic magnesium was .0

Jan 1, 1944

By P. R. Kalischer

IN the production of alloys by powder metallurgical processes it is often necessary or desirable to include one or more components that tend to form very stable oxides Included in this group of metals are aluminum, manganese, magnesium, silicon, and a few others In many cases it is not necessary for the sintered compact to have full density and the other physical characteristics of a cast alloy and in that event no undue precautions need be taken If, however, it s required that the sintered part be entirely homogeneous, and have maximum density and physical properties, some method must be found to reduce the surface films of oxide, which are always present on the metals, and for the metals mentioned above this is always extremely difficult, if not impossible Since the production of high-density alloys is of particular interest to powder metallurgists, some experiments were undertaken to devise methods of reducing the refractory oxides For this work, alloys of iron, nickel, and aluminum were chosen because aluminum oxide is one of the most stable oxides and because these alloys in the right compositions form excellent permanent magnets All of the pertinent properties of the magnets could be accurately and delicately measured by density measurements and magnetic tests of sufficient scope to give a complete demagnetization curve From such a curve the maximum coercive force, residual magnetism, and energy products could be obtained and compared with the same properties for a cast material Any lack of homogeneity, density, or solid diffusion would be immediately apparent as a decrease in the magnetic properties NATURE AND REMOVAL OF SURFACE BARRIERS The early work of the present investigation was based upon published processes In the published information it was claimed that by intimately mixing iron, nickel, and iron-aluminum alloy (50 per cent Fe, 50 per cent Al) powders, compressing such a mixture into the desired shape and size, and then sintering (heating to a temperature below the melting point of the component metals) in hydrogen at 1200ºC or higher, a sound, homogeneous article could be made having the desired physical size, shape, and strength, and good magnetic characteristics However, this early work showed clearly that something in the powder compress was inhibiting diffusion and the process was almost entirely unworkable In the initial phase of the investigation samples of iron powder, nickel powder, and iron-aluminum alloy powder were pressed into separate bars and sintered in hydrogen Both the iron and nickel powders sintered

Jan 1, 1941

By T. A. Dungan

THE thermal processes for the production of metallic magnesium can be divided into two general classifications, the direct reduction of magnesia with carbon and the indirect reduction of compounds of magnesium by reducing agents that are themselves products of carbon reduction. The latter are so chosen as to cause reduction of magnesium compounds wherein only the magnesium is liberated in the vapor phase. Reducing agents used are: calcium carbide, silicon carbide, silicon, aluminum, various silicides or combinations of calcium, aluminum, silicon in iron. All of these are products of highly endothermic reactions and, with the exception of scrap aluminum, can be produced in an open, submerged arc furnace; that is, the arc is covered only by the charge itself. The more investment in energy required to prepare such a reducing agent, the less is the energy required in the subsequent step to reduce the magnesium compound to the metal. It is impossible, however, to avoid the laws of thermodynamics, no matter how much circumambulation is resorted to in the preparation of successively more powerful reducing agents. Since each such step carries forward its own inefficiencies, it appears evident that the ultimate status of such processes is dependent upon the development of by-products. EARLY EXPERIMENTS IN DIRECT REDUCTION The direct reduction of magnesium oxide by carbon has a decided appeal to both the scientist and the industrialist. The successful production of the carbothermic plant at Permanente is a significant fact in the substantiation of this concept. Like most developments, however, the history of carbon reduction of magnesia is not one of triumph after triumph, or immediate heady success to the investigators. It is understood that one of the early investigators conducted an experiment wherein he placed carbon and magnesia in one end of an evacuated tube and managed to heat this end to a temperature high enough that magnesia and carbon deposited at the other end of the tube. The charge, unreduced, appeared to have been completely transported from the hot to the cold end of the tube. This raised doubt for some time as to whether magnesia could be reduced at all with carbon. It was correctly suspected, however, that the magnesia was in fact reduced and the resultant magnesium vapor and carbon monoxide reacted upon one another upon reduction in temperature to reform the starting ingredients. Attempts were then made to dilute the two vapors by passing a considerable stream of hydrogen through an arc furnace charged with magnesia and carbon. Thus by dilution of the products it was expected to obtain metallic magnesium. The results were positive and metallic magnesium was

Jan 1, 1944

By Michael J. Martinson

Mine ventilation has been evolving as a separate field of study since the middle of the nineteenth century, and some practitioners might assert that mine ventilation has come of age as a discrete field in the last decade or two. Certainly the extensive literature now available on many facets of the subject, international congresses, the phenomenal upsurge of interest in mine ventilation in the United States of America since the passage of the 1969 Federal Coal Mine Health and Safety Act, and the existence of a virile mine ventilation society in South Africa with its own monthly journal all point in this general direction; on the other hand the lack of a rational design philosophy for ventilating mines suggests that mine ventilation may still be on the threshold of maturity. To generalise, many mines are still ventilated simply to comply with arbitrary statutory regulations, or with some ill- defined notion of reducing the risk of injury associated with the atmospheric environment in mines. Hazards in this category include oxygen deficiency, toxic gases and particulates, pathogenic gases and aerosols, explosive gases and dusts, and extreme climatic conditions. Although many mines are ventilated to abate the risk of a specific injury, there is inevitably a spectrum of latent and patent atmospheric hazards in every underground mine. The writer (Martinson, 1976) has previously drawn attention to the dearth of material on mine ventilation design in textbooks and technical journals, and to the overly simplistic approach sometimes adopted in the limited work published on the subject. The available material undoubtedly contains useful technical data and persuasive views, but seemingly could not be used to demonstrate the rational engineering approach to mine ventilation design advocated in the present paper. The range of papers presented at the 1975 and 1979 Congresses, and the diverse interests and affiliations of delegates, emphasize the multidisciplinary nature of mine ventilation. Easily recognisable topics include: Fluid mechanics Thermodynamics Heat transfer Flames and combustion Aerosol physics Radiation physics Geophysics and geomechanics Occupational diseases Epidemiology Industrial physiology Despite these heterogeneous connections there can be little doubt that mine ventilation is fundamentally an engineering field and not an off-shoot of some other branch of applied science. The distinction is important because mine ventilation has essentially developed as a form of ad hoc trouble- shooting, and in the process mining engineers have relied extensively on the assistance of experts drawn from other fields. Thus historically there has been limited scope for the application of rational design techniques, and personnel enlisted from scientific disciplines may not have had any previous experience in the intricacies of engineering design.

Jan 1, 1980

By Ralph Hultgren, Bernard York, David W. Mitchell

It is a well-known fact that magnesium-alloy castings are apt to be coarse grained if the melt is not superheated several hundred degrees above the melting point before casting. (The casting temperature varies according to the shape of the mold. A typical casting temperature is perhaps 1400°F.) British practice is to heat to 900°C. (1650°F.) for 15 min., cool rapidly to casting temperature, and cast.' In Germany superheating is carried out at 850' to 900°C. (1560° to I650°F.) depending on the amount of scrap used. It is stated that further refinement will be obtained by prolonging the period of superheating or by increasing the superheat temperature to 950°C. (I740°F.).2 In the United States superheating is carried out at 1600' to 1700°F. (871' to 927°C.), perhaps even higher in some places. It is stated that superheating effects are found as low as 1500°F. (816°C.), but several hours are required.3 These commercial treatments lead to grain sizes in sand castings that may vary from 4 to 8 grains per sq. mm.! in heavy sections and from 60 to IOO in 1/2-in. sections to perhaps 380 in thin sections. It is also generally known that the refining effect of superheating is lost if the melt is held for some time at lower temperatures before casting. Aside from these very qualitative statements, there is little to be found in the literature as to the effect of temperature and time of superheat on the final grain size. Because of the uncertainty of these factors, the Office of Production Research and Development of the War Production Board placed a research contract with the University of California, supervised by the War Metallurgy Committee. This research, which was done under the "Restricted" Project NRC-550, is the basis of this paper, which has been released for publication by the O.P.R.D. The material studied was an alloy prepared from carbothermic magnesium. The temperatures required for grain refinement proved to be widely different from those used in practice, as described in the statements in the first paragraph. This difference is attributed to the fact that the magnesium in the specimens was of carbothermic origin instead of the electrolytic magnesium in common use. Materials and Methods The magnesium alloy studied was one of the most popular sand-casting alloys, with a nominal composition of 9 Per cent aluminum, 2 per cent zinc, and 0.1 per cent (minimum) manganese and the balance magnesium. This is designated

Jan 1, 1945

By R. A. Bergman, C. J. B. Fincham

THERMODYNAMIC properties of many high-temperature systems containing sulfur, such as slags, metal sulfides, and solutions of sulfur in liquid metals, have been studied by means of equilibration with known gas mixtures.'" This method presupposes a complete and accurate knowledge of the thermodynamic data for all possible components of the gas phase at high temperatures. However, a survey of the data available up to 1952 on the thermodynamics of gaseous sulfur species and compounds, by Richardson and Jeffes,' showed that there was considerable uncertainty in the values of the free energies of formation of S, SO, HS, and CS. In many cases, this uncertainty made it impossible to decide whether or not these species would form a significant proportion of the sulfur present in the gas phase in any given system. After the review by Richardson and Jeffes had been published, St. Pierre and Chipman6 measured, by an indirect method, the free energy of formation of SO. This also enabled a clear choice to be made among the three possible spectroscopic values for the dissociation energy of S2 into atoms10 thereby determining the free energy of formation of S from S2, and fixing the free energy of formation of HS more accurately" The main purpose of the present investigation was to measure the free energy of formation of CS, which was still in considerable doubt. For example, at 1600°C, it could be estimated to be +6 +25 kcal per mole,* most of the uncertainty being in the * Based on the dissociation energles of CS6 and S2,5 the heat of sublimation of graphite, and, the assumption that the entropy of formation of CS is the same as that of CO. value of the dissociation energy." A secondary purpose of the investigation was to determine more accurately the equilibrium sulfur pressures over dilute solutions of sulfur in carbon-saturated liquid iron. General Method Dilute solutions of sulfur in liquid iron, saturated with carbon, were brought to equilibrium at 1600" and 1800°C, with known gas mixtures consisting, initially, of A and CS2. After equilibrium had been reached, the melts were quenched and analyzed for sulfur. In the high temperature region of the furnace, an equilibrium was set up between the various possible sulfur species and compounds in the gas phase; namely, CS2, CS, S2, and S. (It can be calculated that the amounts of S6 and S, are negligible at these temperatures:) Morris and Bueh17 and Kitchener, Bockris, and Libermana had previously studied the corresponding

Jan 1, 1958

By B. J. Harlan

The trying times experienced by the steel industry during the past four years have emphasized the necessity of producing pig iron at the lowest possible cost. The trend in both design and operation of blast furnaces has been toward this end rather than toward securing maximum production from a unit or group of units. In the following discussion the trend in design of stacks and auxiliary equipment will be taken up before operation is considered. Although few furnaces have been constructed in the past few years, the trend is definitely toward larger furnaces with a hearth diameter of 24 or 25 ft. Such a furnace is very flexible, being able to produce efficiently any desired daily tonnage between 500 and-1000 or more. The detail of the design of furnace stacks, with the exception of the top, has changed little in recent years. To decrease the velocity of gas through the throat of the furnaces, thereby reducing flue-dust losses, the stock-line areas are constantly being made larger. The top dimensions of the larger furnaces are usually as follows: Stock-line diameter, 19 to 20 ft.; large bell diameter, 14 to 15 ft.; straight section of throat, 5 to 10 ft. high; inwall batter, 1 to 11/4 in. Pe ft. The ratio between the area of the stock line and the area of the large. bell is usually about 1.85 to 1. The stock-line diameter of some smaller furnaces has been increased to that of the hearth diameter of the stack at the expense of the stack batter. Remarkable decreases in flue-dust production are claimed for the so-called " Venturi top," which is achieved by flaring the stock line, in the form of an inverted cone, from a diameter of 17 ft. at 10 ft. below the large bell closed to a diameter of 19 ft. 6 in. at 3 ft. below the large bell closed. Time alone will tell which of the two designs is the better. Because of differences in raw materials, one top may be better for some plants and the other top for other plants. In the search for lower costs and higher efficiencies all operators are, adopting stoves that will maintain maximum hot-blast temperatures with a minimum gas consumption. To meet these requirements, stove capacity of approximately 7 sq. ft. of heating surface and 1.8 cu. ft. of brick volume is required per cubic foot of wind blown per minute.

Jan 1, 1934

By Henry Schaefer

Solution by electric analogy of performance problems of reservoirs containing oil and gas has heretofore depended upon a process of successive approximations based on material-balance calculations, because of variation in fluid compressibility. By the addition or subtraction of electric condenser capacity, the analogy network can be adjusted automatically for changing compressibility due to evolution of gas in the reservoir. The addition of a condenser is accomplished by an electronic circuit, which is described; subtracting a condenser is done by merely opening the electrical circuit by means of a relay. Introduction V. Paschkis and H. D. Baker1 first developed in this country a method of applying the analogy of flow of electric current in noninductive circuits to solution of heat-flow problems and suggested its application for certain other problems, such as flow of fluids or mass transfer and chemical diffusion. Necessary details for applying the analogy to flow of fluids in porous media were developed by IV. A. Bruce;= he classified3 the types of analysis and predictions that can be made by the analogy in class I, when the reservoir contains oil but no gas for the period under consideration; in Class 2, when both oil and gas exist in the free state in the reservoir sometime during the period under consideration. Duplication of bottom-hole pressure history and predictions for class I reservoirs can be obtained directly by electric analogy. Until now, the solution of problems pertaining to reservoirs in class 2 was obtained by successive approximations along with material-balance calculations. The object of this paper is to present a method for simplifying the application of electric analogy to class 2 reservoirs, resulting in a solution of these problems as direct as is possible for class I reservoirs. This is accomplished by an electronic control circuit, which adjusts the analogy network for changing compressibilities of fluids contained in the reservoirs. Analogy Network In electrical phenomena the analogy to two-dimensional fluid flow in a porous media is that of current flow through an ideal conducting sheet. This sheet, perfectly insulated on both sides, has resistance and capacitance uniformly distributed throughout its area but is of negligible inductance. The need for having the surface boundaries perfectly insulated is that good correspondence may be had with a permeable fluid-conducting stratum bounded above and below by impermeable media. 111 actual application the ideal conducting sheet, which has distributed parameters, is replaced by a network having lumped values of resistance and capacitance—the resistances are series elements and the capacitances are shunt elements. The larger the number of lumped

Jan 1, 1947

By H. H. Uhlig

In our study of the mechanism of and the prevention of corrosion in stainless steels, it was considered of fundamental importance to obtain knowledge of the surface structure of such alloys. If corrosion resistance is due to a self-healing oxide layer, which like a paint film protects the underlying metal, it would be obviously relevant were the effort made to make the film less permeable and more adherent; for example, the surface might be expected to respond to an anodizing process, which is found successful in increasing the film thickness and corrosion resistance of aluminum. However, if passivity and corrosion resistance of stainless steels are due to another cause, the attack of the problem would follow another path. One of the most effective techniques for studying passivity and corrosion tendency is the measurement of the electrochemical potential. Not only can one determine by potential measurements whether a metal is active or passive, but also one can determine the degree of passivity and rate of transformation of passivity with time. Chemical media that build up or destroy passivity when in contact with the steel can also be classified by potential measurements. Something can be learned, too, of the effect of alloy additions such as molybdenum to 18-8, known to decrease corrosion of the alloy in chloride solutions. A study of alloys in previous investigations has sometimes included data on the electrochemical potentials. Tammann and Sotterl measured the electrochenlical potentials of alloys of iron-molybdenum and iron-chromium and reperted the critical concentration of molybdenum or chromium at which passivity initiates. Strauss2 made similar measurements for the iron-chromium system. The electrochemical potential3 has also been used to indicate carbide precipitated 18-8. In 18-8, heat-treated to precipitate carbide, active metal exists at the region of the grain boundaries, contrasted with passive metal within the grains, the active metal accounting for a resultant active potential. Several

Jan 1, 1940

By Leslie F. Tedsen, John E. Dorn, Alan E. Flanigan

It is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references I to 4. Investigations on the properties at elevated temperatures are few, however, and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. AS is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hard- ening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "averaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: 1. The higher the temperature, the more rapidly is the fully aged condition attained. :7

Jan 1, 1946

By Albert J. Phillips

When brasses containing from 61 to 62.5 per cent. copper are very rapidly cooled from temperatures near their melting point to below 0" C., unusual results are obtained. These results are quite unexplainable from a consideration of the old copper-zinc constitutional diagram but they can be satisfactorily explained by means of the diagram revised by Genders and Bailey1 (Fig. 1). Experiments on a 60/40 Brass If an alloy containing 60 per cent. copper is heated to any temperature between approximately 760' C. and its melting point, it will consist entirely of beta. Upon slowly cooling, alpha will start to separate just below 760" C. Since this alpha will contain nearly 65 per cent, copper, the beta will be impoverished by its separation. As the temperature decreases the composition of the separating alpha will approach approximately 61 per cent. and the beta in contact with the alpha will maintain an equilibrium composition approaching 54.5 per cent. copper. If the rate of cooling is extremely slow, especially at the lower temperatures, stable equilibrium will be established by diffusion through the alpha and beta so that eventually 85 per cent. of the alloy will consist of alpha containing 61 per cent. copper, while 15 per cent. will be beta containing 54.5 per cent. copper. With a faster cooling rate diffusion cannot keep apace and the constituents will be cored, the alpha varying from 65 to 61 per cent. copper and the beta from 60 to 54.5 copper. In this case the amount of alpha will be less than 85 per cent. and the beta will be increased correspondingly. The general structure thus obtained is illustrated in Fig. 2. When a more rapid rate of cooling is effected by quenching in water, the alloy is retained largely in the beta form. However, the crystals of beta are usually outlined with dark fringes which at high magnifications are found to be very fine alpha-beta structures almost martensitic in appearance. The separation of this fringe can be greatly suppressed

Jan 1, 1930

By Arthur Phillips

The progress made in recent years in the art of dispersion-hardening has naturally led to an intensive study of alloy systems capable of yielding supersaturated solid solutions at ordinary temperatures. In general, the investigations have been confined to rather precise determinations of solubility limits and to experimental approaches designed to furnish more complete information regarding the rate and nature of precipitation under appropriate thermal conditions. Efforts are being made to focus more sharply on the atomic changes that are a direct consequence of the instability of the supersaturated solution. Here precision X-ray methods have come to be of considerable importance because lattice parameter measurements indicate very precisely the concentration of solute atoms in the solvent lattice. In spite of the general acceptance of parameter values as a criterion for the placing of solubility limits, it may be suggested that no thorough appraisal has been made of the several factors that conceivably may affect such measurements. More specifically, little attention has been devoted to the significance of surface energy conditions, specimen size and method of preparation, with particular regard to the genesis of the grains and the surface concentration changes as a consequence of heat treatment and etching. Stenzel and Weertsl recently published the results of a detailed study of precipitation reactions in aluminum-rich copper alloys. They found that, although copper lowers the lattice constant of aluminum, a 5 per cent copper alloy quenched from 150" and 225' C. had parameter values unquestionably higher than that of pure aluminum. Their results seem to substantiate, at least qualitatively, the earlier work of von Göler and Sachs,2 who indicated a parameter value, for the same alloy annealed for 24 hr. at 200° C., some 0.0008Å. larger than that of pure aluminum. Stenzel and Weerts attributed the abnormal lattice dimension to the effect of strain induced by the precipitation of CuA12. Weerts3 later

Jan 1, 1934

By S. A. Montague

Mica can claim a considerably greater importance than would be assumed from its comparatively small dollar volume, which came to about $37,000,000 for the United States industry as a whole in 1957. Mica is one of the strategic minerals. We must depend on imports from distant sources for virtually all of our requirements of high grade block and all of our mica splittings. Mica is essential and indispensable for vacuum tubes and high-performance condensers, two electronic components which are vital military necessities besides being nearly indispensable to civilization today. Composition and Properties Mica is the general name for a group of some nine different minerals, two of which, muscovite and phlogopite, are the minerals used by the mica industry as its raw material. Several of the other varieties are commercially useful-vermiculite, * used for heat insulation in expanded form, and lepidolite, used as an ore of lithium while the others-biotite, roscoelite lepidomelane, paragonite and zinnwaldite have little or no commercial importance. Biotite frequently occurs as an undesirable impurity in muscovite. Table 1 lists various properties and other data concerning muscovite and phlogopite. Chemically, mica is a complex silicate of sodium, potassium and aluminum. Most varieties of muscovite are higher in sodium, and of phlogopite in magnesium. There are no important uses of mica where the chemical analysis is important, except that in some uses of ground mica, the content of iron oxide present as an impurity must be kept to a very low limit. Muscovite occurs in a range of color from the so-called India "ruby" which is more closely a pinkish brown, to light and dark green, with numerous other intermediate shades. Ruby color is usually preferred by industry, especially in the better qualities. When split very thin the color in most [ ] micas disappears. Muscovite mica is frequently found containing black and red "stain" as a homogeneous part of the books or sheets. In most cases this stain or impurity is magnetite

Jan 1, 1960

By Howard Scott

INVAR is the preeminent low-expansion metal by virtue of the fact that it can be prepared with a zero coefficient of expansion at atmospheric temperature. This fact suggests that there is little room for improvement in the expansion properties of the low-expansion nickel steels. The inference is true, however, only so far as the expansion at and near atmospheric temperature is concerned, because the expansivity of invar starts to increase rapidly on heating above 100° C. and soon reaches the value of copper. Guillaume1 met this situation by increasing the nickel content above that of invar. By that expedient, alloys having low expansivity under higher temperatures were obtained, but not without a large increase in minimum expansivity. The increase in minimum expansivity with increasing nickel content severely limits the technical applications of these alloys at high temperatures. Prospects of improving the expansion characteristics of the nickel steels is offered by alloying. Search for an advantageous alloying addition by analogy with other alloy systems, however, is not productive because the low-expansion characteristic is unique with that system. The rule of mixtures usually gives a fair value of the expansivity of other solid-solution alloys, but in the iron-nickel systems gives a value of 18 X 10-6 per deg. C. whereas the actual value is 1 X 10-6 per deg. C. Apparently suitable additions are not to be deduced from such ingenuous considerations. Recognition of the fact that the temperature range of low expansivity in nickel steels is terminated with loss of magnetism affords a more promising basis for the selection of an advantageous element. One may expect from that fact that additions of nonmagnetic elements to the iron-nickel alloys are detrimental to the low-expansion characteristic. Indeed, carbon, manganese, silicon, copper and chromium are detri-mental to the expansion properties and no nonmagnetic element is reported to be beneficial. From the same viewpoint, the addition of a magnetic metal offers prospects of improvement. As two of the three ferromagnetic elements are already present in the

Jan 1, 1930

By S. L. Hoyt

Some of the more important properties of finished materials are strength, ductility, toughness, resistance to alternating and repeated stresses, etc. Of these, the property that appears to have received the least consideration, at least in this country, is toughness, which is due, possibly, to our regarding toughness as a qualitative property or, at any rate, as one that parallels ductility. This arises out of our greater experience with the simple carbon steels in the rolled or forged (non-heat-treated) condition which, qualitatively, are tough if ductile and are not tough if brittle. In this way we have erroneously become accustomed to judging the toughness of a material from its behavior in the tensile or similar test. The point of view presented in the present paper is that toughness, like hardness or tensile strength, should be regarded as an independent property and of sufficient importance to require, in so far as that may be possible, quantitative determinations. If such be true, it becomes at once necessary to devise experimental means for measuring or valuating toughness, and the notched-bar impact test (the Charpy test) is advanced as the most logical test that has so far been developed for this purpose. It is further advanced, with particular emphasis, that we have two kinds of toughness to deal with and, accordingly, they will be dealt with independently. Classification of Materials According to Toughness Toughness has been defined somewhat as follows: Tough materials are those that offer considerable resistance to permanent deformation but which, once such resistance has been overcome, may be deformed plastically, but only by the expenditure of considerable energy. In other words, tough materials may be deformed plastically but they absorb a considerable amount of work in the process. This kind of toughness may be called "static" toughness when the rate of loading is reasonably slow or "dynamic" toughness when the rate of loading is comparatively rapid, as in impact testing, but in all cases the stress distribution is essentially uniform. However, static toughness does not

Jan 1, 1920

By Chester T. Sims, Robert I. Jaffee

The thermoelectric behavior of the Pt—Pt-Re thermocouple and the resistance of rhenium to attack by certain molten metals is discussed. In addition, data are presented on the stress-rupture behavior of drawn wire, the tensile characteristics of rolled sheet, the variation of Young's modulus with temperature, and the effect of specimen size and fabrication method on the work harden ability. Mechanical properties of thoriated rhenium are discussed. This includes data on the effect of thoria in rhenium on tensile properties, ductility, work hardening, and recrystallization. RECENT work by the authors', has described methods of fabrication and some of the physical and mechanical properties of rhenium. Rhenium was established as a high melting, dense, refractory-type metal with favorable mechanical properties. In addition, Todd and co-workers' and others" have studied such properties of rhenium as the work function, specific heat, and the resistance of rhenium to the water cycle. Revelation of these and other properties has led to serious consideration for application as electrical contacts, high temperature thermocouples, and wear resistant materials. chanical properties reported previously,' several additional examinations have been conducted. The stress-rupture behavior and the Young's modulus of rhenium have been investigated at elevated temperatures. Tensile data have been obtained for rolled sheet, and a study of the relative work hardening characteristics of rod, wire, and sheet has been conducted. Variation of Modulus of Elasticity With Temperature—The Young's modulus of a % in. diam annealed rhenium rod was determined from room temperature to 880"C (1620OF). The rod, approximately 6 in. in length, was activated in a transverse vibration apparatus suspended in a furnace. The resonance frequencies of the rod were measured and used to calculate the moduli values. The driven frequency was 569 cycles per sec, and a protective helium atmosphere was used. The data, plotted in Fig. 1, show that the modulus decreases in an approximately linear manner with temperature over the range tested.

Jan 1, 1957