Search Documents

By N. J. Rarmrez, C. Perez, J. D. Calderon, L. Lopez

"Among the thermal characterization of any material, one of the variables to know is the coefficient of thermal conductivity because this value can tell how much heat passes through the material and if the material could be used as an isolator. In order to determine this parameter is required some kind of special equipment and controlled conditions which implies high costs in the development of tests. The present paper proposes a design of a low cost measurement system in order to determine this coefficient with the lower possible error. This equipment was thought for companies or labs where they do not have the economic resources or the infrastructure (environmental controlled labs, heat flux transducers, human resources with specialized knowledge) to do this kind of tests.The system is based on ASTM C 518 - 04 [l] and integrated by two plates (one that contains a thermal resistance and which temperature is controlled by a closed loop controller and the other one with a route of water flow). The thermal resistance is actuated by a relay and a supervisor system checks the total time the relay is on in order to determine the effective power applied to the system. The contact faces of the plates contain a group of temperature sensors connected to a data acquisition system that process and record the temperature in each measurement point.With the power applied to the system, the measurement of temperatures and a process of calibration is possible to determine the coefficient of thermal conductivity. IntroductionWithin the thermal characterization of a material of known variables is the coefficient of heat transfer, since this value can know the amount of heat the material is capable of transferring or isolating. To determine this ratio requires specialized equipment and controlled conditions, which implies high costs in the development of a test. This article proposes a design of a low cost machine to allow closer this coefficient with the least possible error. This equipment was done thinking about companies that do not have the infrastructure (laboratories, controlled environment, heat flux sensors, human resources expertise) and financial resources to conduct these tests."

Jan 1, 2011

By E. O. Wagner, Manuel Gomez, W. S. Landers

The Bureau of Mines studied coking rates of a special Columbia - Geneva six - coal blend to establish the effect of the coking rate on coke properties . The tests were conducted in a 500 - lb , 14 - in experimental slot oven at essentially constant conditions of blend composition , size distribution , surface moisture content , and bulk density . The coking rate was varied as a function of oven flue temperature . Coking rates within the range of 0.56 to 1.35 in/hr were achieved . Increase in the coking rate decreased the size of the coke . The stability factor of the coke showed no significant change with coking rate until coking rates greater than 1.0 in/hr were reached , after which a decrease in the stability factor was observed . The apparent specific gravity increased to a maximum value at coking rates approaching 1.1 in/hr and decreased sharply with further increase in the coking rate . Coke parameters correlated well with the coking rate .

Jan 1, 1963

By P. Knudsen, S. Rosenthal

INTRODUCTION In 2010, Montana Tech was gifted 65 acres of land immediately west of the campus. The parcel of land included an old silver mine called the Orphan Boy Mine. The Orphan Boy and its sister, Orphan Girl, were developed about1895 and operated until 1956. In addition to the gift of land, a significant industry gift was obtained to develop a first class training facility, which we call the Underground Mine Education Center (UMEC). The UMEC has been funded primarily by industry through donations of dollars, equipment, and supplies. The UMEC is a unique hands-on, educational environment for today’s students who are being trained to find, develop and process the worlds' natural resources. The center complements courses in mining engineering, geological engineering, environmental engineering, metallurgical engineering and occupational safety and health. It also serves as a as research facility utilized by students and faculty, and other organizations interested in doing research a hard rock underground mine. LOCATION The Orphan Boy and Orphan Girl Mine are located approximately 700 feet (ft.) apart and the Orphan Girl Mine is part of the World Museum of Mining. Underground they are connected on various levels and all levels below the 100 ft. level are currently flooded. The Orphan Boy mine was 804 ft. deep and Orphan Girl was 3200 ft. deep. The surface locations of the two mines and some of the underground workings on the 100 ft. level are shown on Figure 1 (2015). CONSTRUCTION Land ownership was gifted from BP/ARCO in 2010 and planning started immediately. In June of 2011, site development for the decline to the 100 ft. Level of the Orphan Boy began with a satisfactory portal site developed (Figure 2). We hoped to be able to start driving the decline in July. However, the portal was sited approximately 125 ft. away from a natural gas line that bisected the Montana Tech campus. While outside the right of way for the line, Northwestern Energy requested that no blasting be performed near the gas line until such time as the gas line was abandoned in the fall so decline development was put on hold. The gas line was officially abandoned in January of 2012.

Jan 1, 2019

By W. P. Yant

This report describes result of a study of the carbon monoxide and particulate matter in the air of the Holland, Tunnel and metropolitan New York made by the Bureau of Mines (which had participated in the development

Jan 1, 1941

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021

By Michael E. Charles, Jaroslav J. Vocadlo

"The hydraulic transport of solids through pipelines can have many advantages over other modes of transport. Numerous successful applications both within plants and over longer distances have demonstrated the technical and economic feasibility of slurry pipelining. Solids successfully transported include kaolin, coal, iron ore, gilsonite and limestone, and others, such as sulphur and potash, are likely to be transported in Canada in the near future. However, though the technology of solids pipelining is quite advanced the underlying principles have not yet been formulated past the semi-empirical stage. The main objective of this paper is to present a discussion of the important technical and economic considerations in the design of so lids pipeline systems by reference to typical data. The Worthington slurry pumps and pilot facilities are briefly described."

Jan 1, 1972

To extract the gold from refractory gold concentrate with high sulfur and arsenic, the gold concentrate was catalytically oxidized to expose the gold for cyanide leaching. The effects of reaction temperature, initial nitric acid concentration, reaction time and initial gold concentrate concentration on the conversion rate were studied. The results show that the appropriate conditions for the catalytical oxidation of this gold concentrate are: reaction temperature of 65 oC; initial nitric acid concentration of 25% (wt.); reaction time of 1.5 hours; initial gold concentrate concentration of 10% (wt.). Under such conditions, the conversion rate of gold concentrate is 92%. The solution can be used to prepare nano-iron oxide red pigment. Gases released in the process can be recycled and reused by oxidation absorption. A chemical background of catalytic oxidation is proposed.

Jan 1, 2014

By G. G. Li

"A dynamic ventilation-modeling package, VREX, was used to simulate the mine activities through tracking the equipment movements in underground workings and determine the airflow demand for a new production scenario in a ventilation-on-demand (VOD) system. It incorporates the mine development data from a discrete event simulation and balances the ventilation network using the CANVENT ventilation solver. A case study was performed to demonstrate the capabilities of the software, evaluate the performance of the network and determine the potential energy savings for implementing VOD in a deep mine operation.INTRODUCTIONThe ventilation cost of an underground mine can be significant—up to 50% of the mine’s energy consumption could be used to run fans and provide heat/refrigeration to meet the specified production environment for workers and equipment. The VOD system has proven to be more efficient in operating the fans and supplying the amount of air corresponding to the mine activities taking place in underground workings (Hardcastle, Kocsis, & O’Connor, 2006). In order to properly solve and evaluate the VOD system, a dynamic ventilation modeling software VREX—the ventilation rules engine has been developed to simulate the mine activities and determine the airflow demand for each production scenario within an operation period (Dasys & Cameron, 2011).VREX is a decision support tool, backed by the CANVENT mine ventilation solver (Li, Kocsis, & Hardcastle, 2009), for determining the outcomes of network configuration changes over time. The software incorporates the mine development data with ventilation modeling through the discrete event simulation (DES) performed by SimMineTM. As it simulates the air requirements for different vehicles and activities, VREX can evaluate both the performance of the ventilation system and the potential economic benefits of making operational or technological changes (Pritchard, 2010). For example, the model can be used to assess the economic and environmental impacts arising from modifying regulations to support the use of electric or lower emission vehicles. The combination of DES and ventilation modeling provides a new technology to generate the production scenarios according to mine schedules and activities and to determine the potential benefits for various levels of ventilation control, such as time interval and work shift change."

Jan 1, 2019

By J. D. Noll, J. A. Organiscak, A. B. Cecala

Over the past decade, a substantial effort has been made to improve the air quality inside enclosed cabs of both underground and surface mobile mining equipment to reduce respirable dust exposures by the equipment operators. As part of this effort, the U.S. National Institute for Occupational Safety and Health, (NIOSH) completed a comprehensive laboratory study that determined the significant factors for cab filtration and pressurization systems. From this information, a major underground mining equipment manufacturer designed a filtration and pressurization system that was incorporated into the enclosed cabs of its equipment. A long-term evaluation was performed on the effectiveness of this filtration and pressurization system to improve the air quality in the enclosed cabs of two different pieces of equipment, a face drill and a roof-bolter machine, at an underground limestone mine. This long-term evaluation demonstrated a significant reduction in dust levels between outside-to-inside cab respirable dust concentrations. During this evaluation, a modification to remove one of the filters on the roof-bolter machine simplified the design without sacrificing the system’s efficiency. Tests using particle count instruments performed during nonproduction time periods on both pieces of equipment indicated protection factors greater than 100 when comparing respirable-sized dust particles inside the enclosed cab relative to outside.

Jan 1, 2012

By N. A. Eilertsen

The Aroostook manganese-bearing deposits lie within a rectangle 30 miles wide and 70 miles long. Over 40 different deposits have been discovered in this area, but they have not been mined because the ores are difficult to treat. In 1949, the Maple Mountain area was selected for detailed investigation by the Bureau of Mines, because study by the State of Maine and the Federal Geological Survey indicated that it was the most promising in Aroostook County for developing a large tonnage of reserves. Investigation by the Bureau of Mines disclosed that all of the reported deposits of the central district were located on the limbs of a syncline underlying a pear-shaped area of 283 acres between the crests of Maple Mountain and Hovey Mountain. The ore area has been outlined by trenching and drilling along three sides of the perimeter, while the remaining side is defined by a fault. The area has a length of 6,300 feet and a maximum width of 3,100 feet. Diamond-drill holes have intersected the deposit as deep as 1,550 feet below surface, but additional deep drilling would be required to determine the intensity of folding or warping at depth. The Maple Mountain-Hovey Mountain deposit lies in the slates of Ordovician age and is classified into three zones, of which the upper, averaging about 57 feet thick, is designated manganiferous purple and red slate. The central zone, also averaging about 57 feet thick and containing the highest manganese content, is manganiferous, banded hematite. The lower zone is manganiferous, interbedded hematitic and green slate with an average width of about 33 feet. Manganese minerals occur with hematite in all three units. Trenching on the northwestern slope of Hovey Mountain uncovered other disconnected deposits of manganiferous rocks of earlier age than the ore of the syncline. The general strike of these deposits, which range from 15 feet to 75 feet in thickness, is southwest a length of 5,000 feet. They dip steeply southeast. The ore of the syncline is predominantly deep, hematitic red, inclining to red-dish black, fine-grained, dense, and thinly laminated. It is hard and siliceous. Hematite has, in places, been altered to magnetite. Because of the fine-grained texture of the ore, the manganese-mineral constituents are difficult to determine. Of the manganese silicates present, braunite is the most readily identified. Manganese carbonates and oxides are found also.

Jan 1, 1952

Provide a low-maintenance, reliable means of generating bubbles and controlling bubble size for column flotation. Approach Commercial sparger systems used in flotation columns to process minerals provide only limited means of controlling the size of bubbles generated and the rate of air injection. Generally, these limitations are a detriment to flotation performance, particularly in recovering coarse or fine mineral particles. In addition, conventional bubble generation systems require frequent maintenance, often requiring shut-down of the column itself for repairs. To permit greater control of the bubble size generated in the flotation column and to eliminate the counter-productive problems associated with the operation of current air sparger systems, the Bureau of Mines investigated alternative methods for generating bubbles. Based on the investigation, an external bubble generation system was designed, developed, and laboratory and commercially tested.

Jan 1, 1987

By Teruhisa HORITA

The durability of SOFCs is one of the critical issues to realize the SOFC systems. In order to improve the durability, a precise degradation mechanism should be clarified at the different functional ceramic interfaces in SOFC cells and stacks. This paper reviews the improvement of SOFC durability by the mass transport analysis especially at cathode/interlayer/electrolyte interfaces. We have made a precise analysis on the reaction of cathode with impurities. Especially at the (La,Sr)(Co,Fe)O3/CeO2/ZrO2 interfaces, a significant amount of SrCrO4 and SrSO4 were observed at the (La,Sr)(Co,Fe)O3 surface as well as inside the (La,Sr)(Co,Fe)O3 cathode, which suggested some process occurred for both poisoning. Possible degradation mechanisms were proposed based on the observation data.

Jan 1, 2016

By D. Sprott, P. A. Kirsch, J. Harris, D. Cliff

This paper details the work of RISKGATE, the largest Australian Coal Association Research Program (ACARP) occupational health and safety initiative to date. The program is an interactive online risk management system developed to maximize health and safety performance in the coal mining industry by implementing continuous improvement in managing major unwanted events. The comprehensive knowledge base covers tires, collisions, fires, isolation, strata control underground, ground control open cut, explosions, explosives, manual tasks, and slips/trips/falls. All major Australian coal mining companies contributed topic experts to this broad industry initiative: nine coal mining companies, more than 80 experts, and more than 400 days of individual time for knowledge-capture workshops.

Jan 1, 2014

By R. H. Nafziger

Owing to the growth of alloy steel production and its influence on tramp element levels when recycled, foundries have expressed concern regarding the quality of scrap used to prepare iron castings. Reliable and current information was unavailable on the amount of tramp elements contained in iron castings over time. Accordingly, the U.S. Bureau of Mines, in cooperation with the American Foundrymen&apos;s Society (AFS), analyzed cast iron samples from participating foundries throughout the United States on a quarterly basis to ascertain possible trends. Each sample was analyzed for 28 elements to determine if changes had occurred as a function of several input variables. This bulletin describes the research and presents analytical results and evaluations over a 5-3/4-year period from January 1981 to September 1986. Results show that iron casting compositions are changing with respect to a few tramp elements such as arsenic, cobalt, chromium, tin, and zinc over the period. Changes in charge compositions probably are responsible. Significant variations between zones also were observed with aluminum, arsenic, cobalt, chromium, copper, and manganese.

Jan 1, 1990

By Thomas L. Kesler

IF all of the 14 million tons of kaolin produced in Georgia through 1949 had been mined from a single deposit 20 ft thick, it would represent a mined-out area of less than 1 sq mile. This measure of depletion is in such strong contrast with the large size of the area shown in Fig. 1, from which most of the output has come, that there has developed an optimistic outlook concerning future supplies of kaolin equal in grade to that already mined. Dozens of mines are widely but not evenly distributed within this area, which consists mostly of parts of Twiggs, Wilkinson, and Washington counties. There are scarcely half a dozen kaolin mines elsewhere in the state that have been appreciably productive, although the areas in which they occur may have good possibilities. Most of the efforts to find new deposits, therefore, will be confined to the area shown in Fig. 1, for it is here that the industry has established its facilities, and prospecting is encouraged by relatively numerous outcrops and opened deposits of kaolin.

Jan 10, 1951

By B Murphy, S O’Connell, J L. Heath

In the 1989 best-seller The 7 Habits of Highly Effective People, the author, Stephen Covey, highlights the importance of maintaining not only ‘production’, but also, ‘production capacity’. When operating a modern flotation concentrator, production is often measured in terms of concentrate tonnage, tonnes milled and plant utilisation. There are very few metrics that focus directly on flotation equipment condition in relation to performance, which is analogous to Covey’s production capacity principal. It is evident on many mine sites that flotation equipment condition is not monitored on a proactive basis and that the prevailing culture is to wait for a failure, before addressing an issue.This paper discusses examples of how poor equipment condition can lead to production loss through poor metallurgical performance. Actual examples are given where these problems have occurred in operating plants. An outline is provided on how metallurgical and maintenance departments can work together to protect production capacity and gain more from existing equipment.CITATION:Murphy, B, O’Connell, S and Heath, J L, 2014. Maximising value through maintaining your flotation equipment, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 71–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Donald E. Redmon

This Bureau of Mines report examines the injury experience in the quarrying industry for the years 1968-69. Twenty-eight tables for each year are presented in which disabling work injuries are summarized by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

By Louis A. Turnbull

An investigation of coal deposits near Cerrillos Santa Fe County, N. Mex., was undertaken 14 the Bureau of Mines in 1943 as part of a general program to determine sources of metallurgical coal for western steel plants. Almost all of the coal used for metallurgical purposes west of the Continental Divide Is mined from the Lower Sunnyside bed in, Carbon County,, Utah. Coke used in western steel plants that is produced from Lower Sunnyside a coal is weaker, structurally, than coke used elsewhere in this country. For this reason, western coal operators and steel manufacturers are anxious to develop new areas of coking coal of better quality then the coal produced from the Sunnyside bed. The objective of investigations of western coals was to (a) develop additional reserves of coking coal to supplement proved reserves in the Sunnyside bed. and (b) develop; if possible, reserves of coal with coking quantities superior to those of Lower Sunnyside

Jan 1, 1951

By Vivian M. Troughton, Clifford J. Wren, Tony P. Suckling

"Secant pile walls are used for the construction of deep basement walls and earth retaining structures. Risk associated with secant pile walls is commonly perceived as being the safety of site personnel and the public during piling operations, or safety used in design. It is recognized that both of these are of paramount importance, but additional risks associated with the construction methods must also be considered to complete the risk management profile for any project. For the particular case of secant pile walls, if Clients take a ""back seat"" they may be unaware of the total risk package they are procuring. The authors argue that the piling contractor should be involved at the earliest stage giving input into the overall risk management process. Such early involvement within the professional team will maximise cost benefits to the Client and minimise the delays and cost increases sometimes associated with these works. A consistent methodology for identifying and then managing all the risks associated with secant pile walls is proposed. An example is used to demonstrate how this methodology should be employed. INTRODUCTIONThis paper discusses the value of a complete and integrated risk management process for structures with basements formed using a secant pile wall.The risk associated with any secant pile wall can be consicfered as comprising four components;1. Safety of people on site2. Safety of design or design methodology3. Construction risks4. Commercial risksAny risk management system needs to fully consider and integrate each of these four components to maximise the likelihood of a successful outcome for the basement.This paper concentrates on the construction risks for secant pile walls, as these are not often understood by the Client (in this paper the term ""Client"" also includes the main contractor, principal contractor, Engineer, Planning Supervisor, quantity surveyor and cost consultant)."

Jan 1, 2005