Search Documents

By W. L. Ott, C. L. Lewis

"AbstractA technique is described for preparation of palladium sponge and for spectrochemical analysis of the metal in this form. The precision and accuracy of the method are discussed. Analyses are compared with previous spectrochemical analyses of palladium in the black form. Good agreement was found in the two sets •of results and it is concluded that they are more reliable than wet chemical .analyses of the same material.IntroductionFOR SEVERAL YEARS the problem of platinum metal analysis by spectrochemical methods has been under investigation at the Spedtrographic Laboratory, Department of Geological Sciences, Queen's University. The problem, briefly -stated, is as follows: Samples of platinum, palladium,-rhodium, ruthenium, and iridium are received as fine metal powders, called sponge. Direct spectrographic analysis of this material has not been found satisfactory due to its heterogeneity •as regards contaminant metals, which may be present up to a total of one per •cent or more. Further-more, spectrographic standards are difficult to obtain and difficult to prepare accurately by adding weighed portions of contaminant metals to the sponge. The fact that •contaminant metals in original samples are probably alloyed with the major constituent is a further difficulty since complete fusion of these refractory metals proved impractical in the present case as a means of standard preparation. It •has, therefore, been found most satisfactory to dissolve the metals, prepare standards by addition of solutions of contaminant metals, and to reduce both standards and samples to a homogeneous form. A previous paper, by Hawley, Wark, Lewis and Ott (2) dealt with a method for spectrochemical analysis of platinum and palladium in their black form. Since completion of research on the black technique, the possibility of analyzing palladium accurately in its sponge form has• been investigated."

Jan 1, 1953

By J Loeb, J Dampney, P Cameron

Optimisation of Blast Design and Execution must be done right the first time. It is too late after the ore is broken. Consequences of poor design and execution negatively affect productivity from load and haul through the primary crusher to processing and hence reduce mine site profits. Harnessing and utilising ‘big data’ from geology, geometallurgy, drill hole location, powder loading, blast timing, blast movement and fragmentation to close the loop in blast design and optimise the blast increases productivity across the entire value chain from Mine to Mill. As the internet of things and artificial intelligence increases the quantity of data available, being able to capture and utilise this data to advantage is a challenge. Recent advances in software and hardware together with the increased power of cloud computing allows engineers to close the blasting loop to increase mine site productivity. Numerous case studies over the years detail significant gains from implementing the innovative technologies available to Mine to Mill projects. The opportunity is available for all members of the multi-discipline teams at each mine site to actively ensure productivity improvements are realised and maintained not only in their area, or silo of responsibility but across the entire mine site. This paper refers to recent case studies which outline how significant improvements in productivity are available to all mining operations to increase mine site profitability and dividends to shareholders.

Jun 22, 2022

By Galen G. Waddell

Dilation and contraction of the rock surrounding horizontal access open-ings of a deep mine were analyzed during stope advance to determine what type of measurements, made with relatively inexpensive instrumentation, would best reflect the rock behavior. A variety of instruments, mostly mechanical extensometers, were used. Detailed descriptions are given of Down-the-hole extensometers, floating rockbolt clusters, transit surveys, and other instruments and measuring techniques. Although all of the radial-deformation-rate graphs illustrated useful rock behavior data, the most informative graphs were compiled from data procured with the radial extensometers that penetrated, to various depths, the rock around the access openings. An analysis is given of measurement data on the rock around lateral drifts and across and adjacent to the nearly vertical vein of the Star mine, Burke, Idaho. Several useful relationships were found between the rock deformation rate and the stoping process. Information was produced on the elastic state of rock around an underground opening, effectiveness of stope support, rheology of rock, zone of influence around stopes, effectiveness of rockbolts, axis of maximum strain in a plane perpendicular to the long axis of the lateral, and other phenomena. This information could be of particular value in determining location, design, and support of underground openings.

Jan 1, 1966

By A Kobzev, C Robben

Sensor-based particle sorting of gold ores is the masterclass of preconcentration. The technical challenges of a grade in ppm scale makes a direct detection with currently available technology in milliseconds impossible. Consequently, the detection and classification of particles into ore and waste classes relies on detectable proxies which are the foundation for the classification. These must be reliable and repeatable across the ore bodies processed in future. A sensor-based particle ore sorting equipment must therefore be calibrated systematically by understanding the gold deportation in different lithological groups. Also, it must be in best operational state to minimise possible misplacement. The technical challenges are met by a stringent financial regime governing the business case. Many gold ore sorting projects require a stable grade of gold in the rejected waste significantly below 1gr/t. Two examples are introduced in this paper:  The pilot results and operational experience of X-ray transmission (XRT)-based particle ore sorting for pebble sorting of sulphide associated ore;  Laser-based particle ore sorting for pebble circuit of an orogenic, quartz associated gold ore. Usually, sensor-based particle sorters are installed in the crushing section of a plant. However, for large capacity plants, the number of equipment required, and the associated material handling costs result in significant capital and operating expenses for plants with 1200tph run-of-mine capacity. As a conclusion, it was decided to investigate sensor-based particle ore sorting applied to the pebble stream of two existing semi autogenous mills.

Nov 10, 2020

By John W. Barnes

In seeking cost reductions, control methods are a fertile field because they significantly affect labor and other costs. While process control in uranium mills is excellent by the evidence of high recovery, the costs seem high to those familiar with extractive operations for other metals. To some extent this high cost is inevitable, because of exacting quality control-, the technically complicated recovery processes; poor control over grade and nature of mill feed- special problems arising out of the radioactive property of the material. Practices used in uranium mills and the limitations indicated for instrumentation and automation are discussed. It is concluded that any large investment in automatic controls should be preceded by a careful study of their reliability and maintainability, and an estimate of the net income after taxes smaller plants my find it more profitable, or at least less risky, to concentrate their efforts on the possible reduction of some control problems and to development of a stable force of skilled employees. The observed experience does not inspire optimism that ore-dressing plants can be extensively automated although certain unit operations offer a challenge for improvements in instrumentation and machine design.

Jan 1, 1960

By D. L. McClure

Gold mineralization at the Colosseum Mine is submicroscopic and associated with pyrite. Pyrite occurs in breccia clasts, replacing dolomite, in crackle breccia veinlets with traces of quartz, and as disseminations in two small, interconnected intrusive pipe complexes of rhyolitic felsite and breccias of felsite and wall/country rock. Breccia types grade from felsite plus wall rock of Pre-cambrian gneiss to cross-cutting breccias "of felsite, gneiss, and Paleozoic sedimentary rocks that are in contact with the Precambrian gneiss terrane one-quarter mile (40Om) southwest of the Colosseum pipes. Mineable reserves are estimated to be 8 million short tons (7.3 million metric tons) at 0.074 troy ounces of gold per short ton (2.3 g/metric ton) at a cutoff of 0.03 troy ounces of gold per short ton (1.0 g/metric ton).

Jan 1, 1988

By D Andrew, G Stanway, P Mahoney, C Griebel

The iron ore mining industry is currently going through an adjustment from high to more moderate growth as China’s economy transitions from capital-intensive investment to a more services-oriented economy. We are now witnessing a renewed focus on productivity improvements and cost savings as planned expansions are completed. Despite the scale and importance that the mining industry plays in the global economy, innovation literature is generally more targeted at faster-moving industries with shorter innovation timeframes and lower capital requirements. To fill this gap, VCI set out to understand the state of innovation in the mining industry in 2014. This State of Play report aims to give an objective appraisal of the strengths and weaknesses of innovation in mining. The report has three sections covering both the structure and delivery of innovation in mining:Ecosystem – focused on understanding how the iron ore mining innovation ecosystem system works, including the roles of large and small miners, service companies, researchers and governments. Our recommendations focus on what is required for the system to work well and improve the level and quality of innovation in the industry.Strategy – how do companies define their innovation strategy in relation to their corporate strategy? How are these related to prevailing global and industry trends? How do they communicate this with their business? How successful are they? These are among the questions that this section attempts to answer. Our recommendations are pitched at the executive leadership of iron ore mining and service companies.Delivery – focused on how companies develop and deliver innovation, looking at the success of different structural options, leadership and culture, partnerships and the best approaches to change. Recommendations are aimed at improving outcomes within the iron ore mining value chain, including the role that suppliers play.CITATION:Stanway, G, Mahoney, P, Andrew, D and Griebel, C, 2015. Understanding the state of innovation in the iron ore industry, in Proceedings Iron Ore 2015, pp 631–646 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Herbert L. Lines

This paper is one of a series on mining and milling methods and costs published by the Bureau of Mines. The Ash Peak mine of the Veta Mines, Inc., Duncan, Ariz., is of particular interest in that the only metal of commercial value in the ore is silver. The silver is concentrated by flotation; the concentrate is shipped to a smelter for treatment.

Jan 1, 1940

By William H. Lyon

In 1950 the Program Staff of the Department of the Interior undertook an exploratory study in the projection of energy requirements of the nation. This work was reported in Bureau of Mines Information Circular 7582 by H. J. Barnett. In that preliminary study Mr. Barnett, after exploring the nature of the energy economy in some detail, evolved a method for estimating how much energy will be required in the future, based on estimates of trends in efficiency of energy utilization in specific applications, the physical output of specific energy-consuming industries, size of the population, productivity advances in the economy at large, consumer preferences, and other factors. Considerable new information was developed regarding the nature of energy demands and the possible levels of requirements for each fuel under various assumed business conditions. The study analyzed the interrelationships, including substitutions, among the fuels and emphasized the need for viewing the energy economy as an integrated albeit complex whole. This exploratory study showed a need for a single comprehensive statistical re-port that would assemble and show in a uniform manner the diverse published statistical data on energy commodities now scattered through many publications. A particularly important need was for a set of historical statistics showing the production and consumption of all energy on a B.t.u. basis. As the prospective size and nature of the future energy requirements of the nation are matters of continuing importance, this report was prepared to assist further investigations of the subject. In this report the authors undertake to assemble and present in tabular form, on a uniform basis, the production and use of each of the fuels and electric energy in the United states for three census years -1929, 1939, and 1947. The year 1947, rather than a later year, was selected because it is the most recent year for which census data are available showing the consumption of fuel by each of the manufacturing industries. It is hoped that making data for these 3 years available in one re-port will provide the needed statistical background for further studies of fuel requirements and supplies.

Jan 1, 1951

By L. C. de Kooker, K. Esmaeili, I. Musonda, M. Ferentinou

A numerical investigation of the effect of pore pressure regime on the safety factor and the critical failure mechanism is presented for fly ash storage facility. Pore pressures’ measurements from standpipe piezometers and pore pressure estimated from seepage analysis are used to compare the factor of safety for a fly ash slope. This was applied for considering static and seismic scenarios. A probabilistic approach was applied to account for the uncertainties resulting from the limited data available and support a qualitative risk assessment evaluation. Slope stability analysis is conducted in two and three dimensions, adopting the limit equilibrium analysis approach, and also a finite element seepage analysis, to assess the stability of the slope. The two-dimensional cross-sections were extruded to three-dimensional models to estimate the factor of safety and associated shear failure. The results from the performed analysis suggest an increase in safety factor values of 5%.

Mar 27, 2024

By Michael P. Evans

Traditionally in coal processing jigs have been used to clean the coarse coal fraction, the +3/8" or +1/4" material. Today with the advent of modern fine coal jigs in the United States, its place was moved from the coarse to the inter- mediate coal circuit, the 3/8" x 100 mesh. The most economical coarse coal circuit to build and operate is a heavy media bath circuit. The following table summarizes the cost per raw coal ton processed for a coarse coal jig circuit, and a coarse coal heavy media bath circuit. The flowsheets used to compare these two circuits are shown in Figures 1 and 2.

Jan 1, 1983

By K. B. Nowels

"INTRODUCTION For the last several years the oil industry has been turning more and more toward conservation arid the study of related production problems. It is generally conceded that ultimate recovery is increased by holding the natural gas in thy sand which is net needed in lifting the oil. The retained gas lowers the viscosity and surface tension of the oil and helps flow the oil from the sand. Lewis states that ""while the operator can not control the original conditions of energy and resistance in the sand, he can partly control the efficiency of expulsion. As it is the energy contained in the compressed and absorbed gas rather than the oil that is exhausted, it is but logical to judge the efficiency of a producing method largely by the relative quantities of gas produced with each barrel of oil. If by a change in method the producer lessons the proportion of gas with each barrel of oil, he should increase the total recovery- of oil correspondingly, even if the rate of production is temporarily reduced somewhat.""The effect of ""pinching in"" or controlling the flow of oil wells in an effort to lessen the proportion of has never been definitely known. The general belief has been that ""pinching"" a flowing well causes the oil and gas volumes to be reduced proportionately, maintaining the same gas-oil ratio as before the reduction in flow was made. Studies of gas-oil ratios in many fields have shown that much gas has been wasted, insofar as its effectiveness in oil production is concerned. Swigart and Bopp carried."

Oct 1, 1927

By Dan Ifrim

Soft ground tunneling poses major challenges to the underground industry. Most of soft ground tunnels are in highly urbanized areas, often include limited cover, and include a strong trend of increasing diameters. Therefore, soft ground tunneling works can sometimes cause inevitable ground movements and settlements that may lead to damages to adjacent buildings, roads, structures or utilities; many of these being “lifeline” infrastructure assets. Tunneling operations, Tunnel Boring Machine (TBM) advance rates, and face pressure control can significantly increase or decrease such risks, depending on how well the TBM and operational parameters are applied to the ground conditions. Additionally, the risks of impacting existing infrastructure are heightened in many parts of North America because of cobbles and boulders. To date there is no standardized guideline that determines appropriate tunneling rates nor operator’s guidelines, to ensure safe tunnelling in soft ground. The paper analyzes tunneling records from completed soft ground tunnels to determine a relation between ground conditions, tunnel cover, TBM cutters maintenance and TBM advance rates. The records are discussed to draw several mitigation measures to be adopted during tunnelling, to reduce risks of settlements, over excavation or sinkholes.

Jun 13, 2021

By A. Pearson, Auld. F. A., S. O. Colbeck

"To minimise mine shaft maintenance over the long-term, some potash mine shaft sinking projects have required the provision of a continuous fully welded waterproof steel liner over a substantial depth to achieve zero water ingress. This brings many challenges, including the implementation of a bottom-up construction sequence incorporating extensive waterproof welding and how to ensure the integrity of the welded liner when subject to substantial temperature fluctuations that are likely to occur with a composite steel-concrete liner placed within an artificially frozen shaft excavation. This paper highlights the key challenges and discusses multiple mitigation measures including vertical shaft movement joints and a combined structural-thermal analysis approach. INTRODUCTION Whilst the application of combined steel and concrete shaft liners using a fully welded steel liner is not new and has been used in several previous projects, most notably at Lanigan (Storck, 1968 & Roesner, 1980), recently the need to provide a continuously welded steel waterproof liner for over 800 m length of shaft for a potash mine has been considered. The need for a fully continuous welded steel liner arises from the perceived benefits of providing a fully dry shaft environment to; increase the life expectancy of the shaft; reduce routine maintenance particularly combatting salt accretion and minimising wash down practices; and improve long-term ground stability by preventing salt dissolution. Whereas previous projects have employed discontinuous sections of steel liner, when a fully continuous liner is employed longitudinal shaft strains from thermal changes result in significant deformations that must be either explicitly accommodated or resisted. Note, these thermal vertical expansion forces are more than capable of lifting the shaft collar and head frame structures should they be fixed in place. Typically, shafts are designed to resist vertical forces (collar loads and self-weight) by creating mechanical interlock with the adjacent ground. In competent rock this occurs incrementally with the construction of the shaft liner, and occasional hitch/crib structures are constructed as intermediate foundations to guarantee the transfer of vertical forces at distinct horizons. Usually this means cribs are constructed at first rock head, above the station level, and at the sump, although sometimes additional cribs are formed when entering and exiting weak strata or when a change in shaft liner construction is required."

Jan 1, 2019

The Particulate Mineralogy Unit has been established at the College Park, Maryland, Metallurgy Research Center. The Particulate Mineralogy Unit will have the responsibility within the Bureau of Mines for the characterization of particulate minerals which have potential for adverse environmental effects. The Unit will provide a focal point for identifying particulates in connection with environmental problems related to the activities of agencies such as OSHA, HEW, EPA, and MESA. The Particulate Mineralogy Unit is seeking to clarify the ambiguities surrounding the mineralogy of and terminology used for asbestiform minerals and other mineral particles. The Unit?s investigations of the morphology, composition, and structure of asbestiform minerals and their nonasbestos analogs have made its members recognized experts in this field. The information which it develops on the characterization of asbestos and other particulate mineral forms such as silica should provide a technically rational basis for decisions by regulatory agencies. Those desiring further information, contact Dr. W. J. Campbell, Program Coordinator, College Park Metallurgy Research Center, College Park, MD 20740, telephone: 301-344-4014. ALUMINUM: For over a month, domestic producers have priced 99.5 percent grade primary aluminum ingot at 48¢ per pound. In the same period, merchants raised ingot quotes by 1.5¢-2.5¢ to a range approaching 44¢-47¢ per pound.

Jan 1, 1976

By M. Stephen Enders

The Little Rocky Mountains host epithermal gold-silver bearing vein and stockwork deposits in a syenite intrusive complex. Pegasus Gold Ltd. is currently mining the oxidized deposits by open-pit methods and recovering gold and silver by heap-leach processes. A geologic program has been designed to effectively determine the basic ore characteristics; 1)mineralization; 2)oxidation; 3)structural setting; 4)lithology; 5)alteration; and ultimately, 6)the leachability of the ore. Geologic mapping, sampling, drilling, assaying, and testing are routinely used in exploration, development, production control, mine planning, and ore reserve estimations. Timely and accurate assay results are essential for the program's success.

Jan 1, 1983

By Willem P. C. Duyvesteyn

A novel hydrometallurgical process for Escondida copper concentrates has been developed by The Minerals Laboratory of BHP. The Escondida Process consists of concentrate leaching, solution purification, electrowinning and residue flotation. Part of the copper will be sold as high grade concentrate and part as high purity SX-EW copper. Contrary to previous efforts for the development of a hydrometallurgical process for copper concentrates, this patented process does not advocate the total dissolution of copper. It only aims for the copper that is readily soluble in a mildly oxidizing environment with an ammoniacal or acidic lixiviant. Both lixiviants were studied, but ammonia was preferred because of fast kinetics at ambient temperatures and pressures. By controlling the oxidation potential, the formation of sulfate ions and, consequently, of an ammonium sulfate byproduct, is precluded. These mild leaching conditions also prevent the dissolution of unwanted impurities and result in the production of ultra-high purity electrowon copper. Solution purification is carried out by solvent extraction with LIX-54. The very high loading capacity of this organic results in a compact SX circuit, consisting of two loading, one scrubbing, and one stripping stage. As the organic is selective for simple copper ions, the copper amine complex is broken down and free ammonia is regenerated and recycled for leaching. High purity copper cathodes are produced in a conventional sulfuric acid based electrowinning system. One scrubbing step is needed to separate the ammoniacal circuit from the acid circuit. Limiting copper dissolution to less than 50% also provides an opportunity to produce high grade concentrates by residue flotation. Copper recoveries in excess of 98% with precious metal values reporting to the final concentrate can readily be obtained. Complete breakdown of the copper mineral- pyrite middlings results in a final concentrate grade that can be even higher than the original feed material. The Escondida Process also provides an opportunity to accept lower grade copper concentrates producing improved copper recoveries in the mill and yet high quality concentrates for marketing. The Paul E. Queoeau International

Jan 1, 1993

By G. W. Josephson

VIRTUALLY every year inventors find one or more startling new uses for one of the varied products of the nonmetallic mineral industries. For example, in November a major step toward positive control of rainfall was made when an experimenter converted a cloud to snow by dropping a few pounds of solid carbon dioxide into it. Other examples of ingenuity in the development of markets and production methods are noted in the following pages. For most of the industrial mineral products one of the outstanding features of 1946 has been the high level of production. There are exceptions, such as quartz crystal and lithium, whose production capacity during the war outgrew current peacetime needs, but they are few. Some technical men point out that this prosperity is not an unmixed blessing to technologic progress, because so much effort must go into day-to-day production problems that relatively little opportunity is left for the pursuit of new developments.

Jan 1, 1947

By George J. Karcas

"Non-ferrous metals such as copper, nickel, lead, zinc and precious metals are produced via the electrorefining and electrowinning processes. Apart from controlling electro-chemical conditions for the production of these metals, there has always existed the challenge of controlling the corrosive effect of the electrolyte environment which serves as the medium for non-ferrous metal production.The practice of acid containment in electrometallurgical operations has entered the world of high technology with the advent of advanced acid resistant materials such as vinyl ester resin which is either combined with aggregate to form polymer concrete or used to line various acid containment vessels and ·surfaces. ill comparison to some Asian, European, and African copper refineries, the North and South American copper industry has recently embraced quite heavily in the use of polymer concrete electrolytic cells and process vessels, such as electrolyte storage tanks, and in the use of vinyl ester resin for corrosion protective surface sealing 'systems in lieu of epoxy, acrylic and other materials because of its combination of higher corrosion resistance and superior flexibility.Electrolytic cell construction has undergone a transformation from a multiple part configuration to a single piece moulded/cast unit. ·The one piece moulded polymer concrete cell, which has been patented by Corrosion Technology International, with the overflow, decant, inlet, fast fill and segregation systems integrally designed is now the industry standard.. The combination of a wood, steel, or concrete frame with a lining made of lead, asphalt, rubber or plastic has been historically successful in providing limited protection from chemical and mechanical attack in electrolytic cells and electrolyte storage tanks all over the world. These combinations have now become obsolete as materials such as polymer concrete provide exceptional corrosion and mechanical protection with greatly reduced maintenance requirements and improved efficiency and productivity for the tankhouse. ill addition, polymer concrete can be disposed of in a regular land fIll which is much less costly than disposing of contaminated concrete that is normally associated with conventional lined concrete cells."

Jan 1, 1997

By H Rossiter, A Maddever, J Market, P Jeanneau, A Virani

It is generally acknowledged that the head grade of the world’s copper resources is declining. Accordingly, there is an increase in the volume of resource material being mined and processed to maintain copper production. This has led to increases in cost base accompanied by reductions in Life of Mine (LOM) Net Present Value (NPV). The higher tonnages of material mined are driven by increased quantities of lower grade material required to satisfy the short term mine model. In turn, this has brought an increased focus on sampling and assay methods, since any error associated with estimating the grade of each block and determining its correct destination serves to magnify the losses that will occur. Presently most open-pit copper mining operations use blasthole sample assays to feed their shortterm model. The problematic nature of blasthole sampling is well documented (Engström, 2017), particularly the poor timeliness of the data and the significant errors that are inherent to the technique. Methods to improve grade control, such as drilling a separate grade control grid, have been proposed but come with their own cost, logistical, and accuracy shortcomings. A recent development in grade estimation is the Pulsed Fast and Thermal Neutron Activation (PFTNA) downhole logging probe. Deployed on an efficient semi-autonomous platform, PFTNA is being aggressively adopted in the Australian iron ore industry. The technology provides in-situ elemental analysis of the geological formation, delivering high accuracy, high efficiency, near realtime data from a sizeable measurement volume. In this paper we consider the application of the technology to copper. Whilst there are several operational components to such a value proposition, we focus on the benefits of improved gradeestimation. A simulated copper mine is used to model the quantum of improvement expected from a reduced grade-estimation error, which reduces the likelihood of misallocating material to the wrong destination, which in turn increases NPV.

Nov 10, 2020