Search Documents

By T. W. West

INTRODUCTION This paper presents an assessment of conventional flotation technology. In addition it presents some ideas which can be used to change the perception of what may be done with conventional flotation equipment to maximize its efficiency. Perspective of Conventional Flotation Technology 1. Flotation in many coal preparation plants is defined as something between a necessary evil and a non-viable concept because: -Too much art is required on a continuous basis to achieve uniformly acceptable results. -It is expensive, the capital cost in dollars per ton of circuit feed for flotation and dewatering is high. -It is a difficult process to use when SO2 reduction governs system design and equipment selection. -It creates a product (fine coal froth) that is difficult to dewater in the presence of BTU/lb as-received pressures. -It is a difficult process to control from a management standpoint, there are no dependable set points to rely on. 2. Many froth cell circuits are 0.5m x 0 (nominal 28 M x 0) feed which is sourced from screen/cyclone underflows. The original intent was to obtain maximum yield at acceptable product quality and moisture using disc filters. (See Figure #1) 3. An alternate to conventional flotation and its perceived to be limits of efficiency, capital costs, etc. is to move towards such developing flotation technologies as column flotation, reverse flotation, and microbubbles. A lot of work is being done to move these concepts thru pilot stages into full scale, commercial plant operation. The majority of the coal producers and coal preparation plant designers view these concepts as being in the development/pilot plant stages. OBJECTIVES Based on the preceeding comments of the perspectives of the coal producers and plant designers, the options are limited. They can make do with what they have available to them in the way of industry standard equipment and practices or they can move forward with developing technology. I feel there is a third option: what can we really do today with what is available to us, without reinventing the wheel? APPROACH 1. When processing coal against ash and SO2 restrictions, the fine clean coal stream can be the best stream on the clean coal conveyor due to the release by size and the ability to create a high BTU/low sulfur (dry basis) product. 2. Targets: -Consistent raw coal size consist in the plant feed . -Do not put pyrites in the froth cells. -Adjust criteria defining good flotation away from yield towards maximum BTU recovery at minimum ash. -Limit the froth cell feed size consist to 0.15 mm x 0 (nominal 100M x 0). -Establish and maintain a correct, consistent percent solids in the froth cell feed. -Select flotation reagents with care. -Introduce reagents in the proper sequence.

Jan 1, 1988

By Walter Miller

AFter a year's continued impact of war, the task of the petroleum-refining industry stands out clearly and looms up in larger aspect. This time it is not, as it was so largely in the first World War, simply a matter of increased quantity—more and more of the same petroleum products that had substantially been standard for years. In this era the emphasis is largely on newer and improved materials which had been produced, if at all, in comparatively insignificant quantities, and for which manufacturing equipment was not available on a large scale. At the beginning of 1942 four great product needs (besides a number of lesser ones) confronted the industry: 100-octane aviation gasoline, toluene for T.N.T. production, high-quality lubricating oils for aviation and Army equipment service, and petroleum chemicals for synthetic rubber manufacture. The difficulty in presenting a review of engineering progress in petroleum refining during 1942 is that there is so little one is free to say about so much which has been and is being accomplished. At the opening of 1942 the program was to increase the then existing capacity of 50,000 bbl. a day of aviation gasoline to over 150,000 bbl. daily by building new plants at an estimated installation cost of $150,000,000. Later in the year. after the announcement by President Roosevelt of a large increase in the program for war-plane building, additional contracts were made between the Reconstruction Finance Corporation and rehers to raise the capacity to 250,000 bbl. per day. The greatly increased scope of the war activities in all parts of the world, the obligation of the United States as the arsenal of the United Nations, and the greater importance and use of bomber, transport, and cargo planes will undoubtedly bring about plans and installations for a further increase in production of aviation gasoline over the present announced plan. In this connection, Jesse Jones, Reconstruction Finance Corporation Chairman, announced that as of Oct. 31 the R.F.C. had through its subsidiary Defense Plant Corporation entered into contracts for the construction, expansion, or equipping of 28 plants to increase 100-octane aviation gasoline production, but gave no data on 'capacity involved or completion dates. His list did not, of course, include a number of existing plants, and some installations being made by companies who are themselves financing the construction. Production from existing operating installations was materially increased in a number of instances as a result of pooling knowledge of improvements in operation and also by the exchange of Components going into 100-octane blend to enable greater quantities of aviation gasoline to be produced from the over-

Jan 1, 1943

By Rich Akerman

as 1866, I wish to assure both these gentlemen that I had not seen the section when I designed mine, :md even if I had, I should not have then dared to put it forth as a standard for English rail makers; tind the soundness of my opinion has a simple but conclusive proof in the statement made concerning the extra price which was at that time required for their production. I need not say that I highly approve of the original Welch section, for it is in principle similar to the design which I made ufteen yeam subsequently; and from a professional point of view I would fully concecle to Mr. Welch the credit of first designing the modern steel-rail section. From com- mercial, matter of tict, and practical point of view, he was, however, before his time by many years; or to put it in another way, rail making was ten years behind its time when the new metal steel was first introduced for rails. If his design has been incorrectly identified with my name (as the sections are similar in principle, though they differ in thickness of flange and web), I beg to say (1st) that I much regret the misun- Understanding which has arisen through no fault of niine, aud (2d) that no confusion has been intentionally created by me. It is a pity that the section designed so long ago has not been made public at an earlier date, as it would make a really goal stand- and pattern, anil even now be quite equal to present requirements. In conclusion, I wish to say that I have never desired to claim any invention or novelty by the publication of my sections; they Were put forth as being such as English railmakers could and would produce at the ordinary market. price, and as being the best and most suitable to be so obtained. Had Mr. Welch or Mr. Holley put forward theirs ten or fifteen years ago, I should have been the first to recommend theru. In fact I should have been glad to see their narnes associated with rail patterns in their own country, in the same way as mine has been. PROFESSOR RICH. AKERMAN, STOCKHOLM, SWEDEN: i AGREE with your (Mr. Sandberg's) views that it is too early yet to stipulate only one definite chemical composition in the rails. Such a stipulation, I think, might he justified, if it were not for the manganese; but this metal changes the properties of the iron aud steel in tho same direc- tion ae carbon, silicon. and phosphorus, by increasing its tensile strength, stiffness, hardness, and brittleaess. If the iron and steel does not only contain carbon and manganese but also phosphorus,

Jan 1, 1881

[Consider the situation where we wish to estimate the value of a block of ore W from the values of n samples wt (i = 1, 2.... n). The samples can be located anywhere inside or outside W. The blocks and the samples can have any size or shape (Fig. 8.1). We define ws as the set of all the samples wi: WS = Iw1; W2; W3.. . wn and we wish to estimate the block W using the samples ws. Let xi be the value of the ith sample and µw the unknown average value of the block. We can estimate µw from the average value of all the samples. Let µw be the estimator of µw. As the samples need not be of equal size, the sample average is: µw = wi xi/~ wi. (8.1) The mean squared error made when estimating µw by µw is known as the variance of estimation of W by ws. It is the error made when giving the value of the sample set ws to the block W and is written o2E (WS to W). By definition: o2E (ws to W) = E [(µw - µw)2]. (8.2) If n = 1, this error is known as the extension variance. Since the sum of the weights given to the sample values is equal to 1,0, the estimator µw is unbiased (the question of the absence of bias is studied in more detail in Chapter 9): E [( µw - µw)1 = 0. (8.3) The error (µw - µw) has zero mean and a variance o2E = E (W8 to W). If we assume that this error is normally distributed, we can define confidence limits for µw. Let tP be the value of the standardized normal variance t such that the probability that t is less than tP is p: (t,) = .\/27T f exp (- t2/2) dt = p (8.4) The probability that µw is larger than µw + t1-P oE is p. The probability that µw is smaller than µw- t1-P oE is p. The following approximation formulae are often used to calculate 2p central confidence limits for the block value: 68% central confidence limits (p = 16%): µw - o2E, and µw + o2E. 95 % central confidence limits (p = 2,5 %): µw - 2 oE, and µw + 2 oE. Tables of the function 0 can be found in any textbook on statistics (for example, Fraser, 1958, p. 388) (see Table 7.2). [ ] The last line of Table 2.2, corresponding to f = 00, also contains the value of tP for p = 80, 90, 95 and 97,5 %.]

Jan 1, 1978

By Arthur Wade

The most important development in connection with the search for oil in Australia during 1940 was on the legislative side. Prior to 1939 legislative enactments in the various states with regard to prospecting for petroleum were such as to prohibit large-scale effort and to bar the major oil companies from operating. The preparation of the Wade Model Bill for the Commonwealth Government in 1939 and the acceptance of the Bill in principle by all States, has gone far to remove these obstacles. Amending Acts, largely based on the Alodel Bill, have now been passed by all States with the exception of New South Wales and Tasmania. In New South Wales an Amending Bill is being drafted, while the Govern-ment of Tasmania is preparing to introduce an Amending Bill provided there is any demand for it. Noteworthy developments followed immediately on the passing of these Amending Acts. The Shell Company (1)1 and the Superior Oil Company of California (2) too$ up large areas in Queensland and com-menced work during 1940. Caltex acquired a big tract of country in the Kimberley district of Western Australia (3) and has made application for an area in the Territory of Papua. An Australian company, The Phoenix Oil Extraction Co., has obtained a permit to prospect over an extensive area bordering the south coast of Western Australia (4). Other developments are foreshadowed. The Shell Company is making an intensive examination of its area in Queensland (I). Geological, geophysical and aerial surveys are in progress. Caltex has three geological parties in the held in Western Australia while Superior Oil Company of California has done some geological work in the interior of Queensland (2). None of these concerns envisages a drilling campaign in the near future. Much exploratory work is necessary. Further work has been done by the companies that were already operating in 1939, though an important Australian company - Oil Search—has abandoned the work of prospecting in Australia. This company has subleased its holdings, at North West Cape in Western Australia (;), to Caltex on a royalty basis. The company also maintains its holdings in, and connection with, the Australasian Petroleum Company Proprietary Limited, which is a combination of Standard Oil (New Jersey), Anglo-Iranian and Oil Search. This company is operating in the territories of Papua and New Guinea. Drilling Victoria.—Although a good deal of drilling was done in the LaBes Entrance Tertiary Basin of Victoria (7), no appreciable production of oil was obtained. In order to test the extent and possibilities of the oil-bearing sand in this region, the Commonwealth and State Governments jointly put down six scout boreholes to depths of between 1200 and I500 it. The results were nega tive. A deeper exploratory horehole put down by the Governments at Seacornbe, or 26

Jan 1, 1941

By W. Spencer Reid

ALTHOUGH there have been some developments during the last five years which have had far- reaching and important bearing on lead smelting, it cannot be said that any basic principles of pyrometal-lurgy have been discovered. Eighteen or twenty years ago the Dwight & Lloyd sintering machine was intro-duced and literally turned the roasting end of lead smelting upside down. There has been nothing com-parable to the advent of the sintering machine during recent years. Actual blast-furnace practice today is slightly, if any, better than it was five years ago ; although immeas-urably better than it was twenty to thirty years ago. Some tell us that as far as cleanness of slags is con-cerned, it is no better today than in the days of the old Romans. The metallurgist of a generation ago did very good work, considering the equipment he had available. It is true he was working with the cream of the ores, the clean oxides and carbonates and the low-zinc sul-fides. He was troubled very little with high zinc and selected his type of slag according to preference of -some authority such as Eilers, Iles, Raht, Hahn, etc. As these free-smelting ores were depleted the complex ores were encountered, and the metallurgist gradually discovered that he had to forget the old type slags and run a slag according to the percentage of zinc on the charge. I believe it is now universally agreed that SiO2 and CaO must be lowered and FeO raised in a slag as the ZnO increases. The ratio of these variations is practically uniform and can be relied upon over wide fluctuations of the determining element, zinc. These "bastard" slags, as they are sometimes inappropriately designated, are actually in daily use, and the metallurgist of today has been forced to adopt certain standards, as a guide to successful operation. These slags practically refute the old Eilers' theory that all good slags are chemical combinations of SiO2 with FeO and MnO, and CaO and MgO. Eilers' and the other type-slag theories were based upon the assumption that a good slag must con-form to a definite formula, such as 3 (FeO)2 SiO2 + 2 (CaO)2 SiO2 or 2 (FeO)2 SiO2 + 2 (CaO)2 SiO2 which respectively figure 31.3 and 36 per cent SiO2. The SiO2 was supposed to remain constant even with the entrance of impurities such as Zn and A1,0? into the slag. The increasing amount of impurities, espe-cially Zn, soon discredited the theory, for in actual practice the slag failed to run freely.

Jan 1, 1927

By J. T. Shimmin

THE past twenty-five years has been a period of unparalleled improvement in all lines of mining and metallurgical equipment, but probably none has undergone greater refinement and development than the vacuum filter. Beginning a quarter of a century ago, there has been steady advancement in the art of vacu-um filtration until today its use has become virtually standard practice for dewatering throughout the entire metallurgical industry as well as in important parts of the chemical and industrial processing fields. The credit for the first successful application of vacuum filtration 'at the Consolidated Mercury mines in Utah in 1902 undoubtedly belongs to George Moore. There, it is said, his filter reduced the loss of gold in the slime and sand from $1.25 to 40c. per ton. Successful applications were subsequently made by Mr. Moore at the Liberty Bell mines, Telluride, Colo., the Lundberg, Dorr &Wilson mill at Terry, S. D., and elsewhere. E. L. Oliver is generally credited with, having done the most to work out the necessary continuity of op-eration exemplified in the well-known continuous vacu-um filter which bears his name. Others made improve-ments also, but in my opinion all the new ideas advanced in recent years are modifications of the fundamental principles originated by the two pioneers, Moore and Oliver. Considerable interest has been shown recently in the new type of continuous internal-type vacuum filter which is associated with my own name1. In response to frequent inquiries regarding it and the steps which led up to its invention, I am giving herewith a brief account of the early history of this development and some of the more important installations which have been made during the last year or so. A. M. Nicholas (now deceased), an Australian engi-neer, conceived the idea, several years ago, of manu-facturing a continuous vacuum filter with the filter medium applied upon the inside of the drum, as con-trasted with existing drum filters in which the medium is applied externally. Nicholas recognized that a ma-chine of this type would be simpler than one with a tank and would overcome some of the difficulties en-countered with tank filters on certain classes of pulps, and he appreciated the value of having filtration take place in the same direction as the gravitational settle-ment of the solid particles in the pulp, the pulp being retained within the drum instead of being held against the outside surface. The ease of starting up after a shut down was likewise realized by Nicholas. It was tried in the United States, but was not entirely success-ful primarily due to mechanical defects.

Jan 5, 1928

The Molycorp operation at Mountain Pass, California, is unique in that it is the only place in the world where bastnasite is mined. The orebody is a metamorphic carbonatite; the mineral of importance is bastnasite, a fluocarbonate containing principally cerium, lanthanum, neodymium, and praseodymium, with small amounts of samarium, gadolinium, and europium. In addition, appreciable quantities of barite, calcite, and strontianite are present. Molycorp had mined and processed the bastnasite ore since the early 1950s at a rate of about 100 tpd by a unique hot flotation process in a plant originally used for cyanidation of gold ore. The concentrate was primarily used in high quality glass polishing, lighter flints, ceramics, and in specialty steel making. Then in the early 1960s, Molycorp and the Colorado School of Mines Research Foundation developed a solvent extraction process to recover europium from the bulk rare earth concentrates. In 1965 a new SX plant was constructed to produce this material for use as a red phosphor in color television tubes. Because of the demand for this material, a new 500 tpd concentrator was designed and constructed in 9 ½ months. Then, because of a sharply increased demand for europium, the plant was expanded to 1200 tpd only four months after completion of the original construction. The crushing section of the new plant was designed similarly to those portable units used in road construction and arrived on the site in ten major pieces. Foundations were concrete piers; and after their completion, the entire crushing plant composed of primary and secondary crushers, conveyors, and a screen was erected in fourteen days by a crew of ten men assisted by a mobile crane. Pit-run ore is loaded into 35-ton trucks by a 7 yd (5.4 cu m) loader, trans- ported to .the crushing plant, and dumped into the 65 -ton concrete pocket. A 42 in. by 20 ft (1.07 m by 6. 1 m) apron feeder feeds ore to the 30 in. by 42 in. (760 rnrn by 1070 mm) single toggle jaw crusher. Crushed ore is trans- ferred by a scissors conveyor to a 5 ft by 14 ft (1.52 m by 4. 27 m) double- deck screen which produces a final ¾ in. (19 rnrn) product with the oversize being treated in a 4 ¼ ft (1. 3 m) standard cone crusher. Cone crusher product is returned to the first scissors conveyor to join the primary crusher product. Dust collection is by a wet scrubber, and an operator's control room is located to overlook the primary. The entire crushing is in the open, and a 30-ton mobile crane is used for maintenance. Molycorp’s two-stage crushing plant is an excellent example of functional design for a small mining and milling operation.

Jan 1, 1978

The Telfer Gold Mine, owned and operated by Newcrest Mining and located in Western Australia, is currently being expanded. A new underground sublevel cave development is proposed along with an appreciable expansion of the open pit. The Telfer area is generally subject to low rainfall, however, during the wet season cyclonic events can result in sizable rain events, which have the potential to cause substantial inflow. In addition to this, during the first five years (nominal) of the mineÆs life, there is the potential for drainage paths between the pit and the underground mine via decommissioned underground workings which lie directly under the pit. After this initial five year period the pit floor will be mined out below the old workings and will therefore no longer connect to the underground, however cave breakthrough to the surface may start to occur thus providing another water path into the underground mine. To arrive at an optimum, safe solution for dewatering the mine that successfully addressed the above items, a rigorous risk analysis was included as an integral part of the design process. This involved the determination of the probability of events occurring and the consequences of these occurrences. This was compared against the cost of mitigation for the various events. This paper outlines the process by which a safe concept addressing all the issues relating to dewatering the proposed mine has been arrived at. This process included: Establishing the pit catchment areas. These were based on historical run-off data and took into account practical mitigation works. Establishing an Average Recurrence Interval (ARI) based on reference material and historical rainfall data. Utilising a standard approach based on Australian Rainfall and Run-off (ARR) to calculate pumping and storage requirements for the various catchments. Analysing the 20 years of recorded rainfall in the Telfer area to establish the duration, magnitude and sequence of events. This analysis assisted in determining the surface run-off coefficient. Establishing potential water storage areas and determining the risks associated with using particular storage options. Establishing the percolation rate through the cave zone. A degree of uncertainty regarding the percolation rate in the cave zone required that the consequences of using various percolation rates were considered to aid in establishing the rate which was adopted. Establishing preliminary concepts and determining the most economically viable concept. Conducting a risk assessment based on the principles outlined by Australian Rainfall and Run-off (ARR) to confirm that the appropriate Average Recurrence Interval (ARI) had been selected. A risk assessment was also conducted in accordance with client requirements. Establishing the optimum pump station sizes and storage capacities. Establishing the appropriate numbers of duty and standby equipment. By using the foregoing process, which included a number of stages of risk analyses, an optimum dewatering system concept was produced.

Jan 1, 2003

By Jorge Goldfarb

El presente texto señala la importancia de la investigación científica donde se explicita los fenómenos básicos asociados a los procesos productivos. Este conocimiento es el que sirve de base a los tecnólogos para controlar, modificar o cambiar esos procesos. Sin una comprensión de los factores que regulan el comportamiento de los sistemas, es virtualmente imposible su control. En este sentido, los trabajos de investigación básica están dirigidos a obtener mayor información sobre las características de los fenómenos físico-químicos superficiales que se consideran importantes para una mejor comprensión de los mecanismos de acción de reactivos colectores y modificadores. Por ello, se presentan trabajos de flotación de minerales oxidados como los mecanismos de sulfidización, estudios de agregación y desagregación en suspensiones de compuestos oxidados de cobre, adsorción de xantatos, electroquímica de los procesos de sulfidización y absorción de xantato.

Nov 1, 1973

By J. Bender

The objective of this research was to (1) Further develop cyanobacteria mats' for metal-tolerance and cold-tolerance, (2) test them for durability in the field environment and (3) assess them for metal sequestering potential with actual and simulated field samples. Results show that mats performed well In the field and effectively sequestered metals from actual and simulated field samples. Metal uptake from Iron Mountain Hine samples was for Ins 87%, Cu and Cd 99%, Initial concentrations (mg/L) were Zn = 3,250, Cu , 279, Cd = 28. In solutions simulating the Gulf Tunnel drainage, Zn and Mn were effectively removed by mats immobilized on glass wool. Effluent water, after treatment, generally had a Ph of 7 .5-8.5. Al though the final metal concentrations in the mats 'harvested from the decontaminated water were only 1% or less, the actual mechanism of metal deposit was probably a mat-mediated alteration of the environmental conditions causing the metals to deposit outside the mat as oxides or carbonates. Bioflocculents, released by the mats, were likely involved in the metal-removal process.

Jan 1, 1996

By J. Shibata, N. Murayama

"Rare earth elements are present in more than 100 minerals, of which monazite, bastnaesite and xenotime are typical. Rare earth elements have excellent chemical and physical properties for industrial use in functional materials such as phosphors, magnets, electronic components, abrasives and catalysts. China produces more than 90 % of the world’s rare earths, and Chinese trends significantly influence the demand and price of rare earths. From the viewpoint of resource securement, it is desirable to separate and recover rare earth elements from low-grade resources and wastes. Phosphate gypsum, which is a by-product of wet phosphoric acid manufacturing, contains low concentrations of rare earth elements. In this research, the separation and recovery of rare earth elements from phosphate gypsum were investigated. A series of recovery methods including washing of phosphate gypsum, leaching of the rare earth elements with sulfuric acid, adsorption and desorption of rare earth elements by using ion-exchange resin, and precipitation of rare earth oxalates were carried out. The separation of rare earth elements from Ca2+ simultaneously leached from phosphate gypsum was also investigated."

Jan 1, 2014

By G. J. Mei

Separation of hematite and iron-containing silicate gangue - aegirine by Flotation using fatty acid collector and (NH4)2SiF6 depressant was investigated in this paper. The flotation tests with single minerals show Ammonium hexafluorosilicate (AHFS) is a selective depressant for aegirine in hematite flotation in weakly acidic medium, which can strongly reduce the flotation recovery of aegirine in the pH range of 4~5 while has no evident effect on the flotation of hematite. The results of flotation tests with actual ores show the separation of hematite from aegirine gangue by forth flotation was possible, and good selectivity was achieved. Chemisorptions were observed on aegirine mineral surface treated by AHFS solution by using SEM and IR spectrum measurements. On the basis of coordination chemistry, a comprehensive mechanism, which reasonably explains the selective depression of AHFS for iron-containing silicate, is also proposed.

Jan 1, 2014

By Jaime Fernández Concha

El presente texto señala la ubicación, fisiografía, geología general y cubicación del depósito de Fierro del Cerro Tarpuy y Cerro Mirador ubicado en el departamento de Arequipa.

Jul 1, 1956

Because surface mining removes the original plant cover from the land and exposes the soil, special care is needed. Until the mined land is stabilized by revegetation, snowmelt and rainfall can pick up sediment and erode mined lands much faster than undisturbed areas. Sediment control is an important aspect of protecting the environment during mining and reclamation because without it, large amounts of sediment can clog streams, increase the risk of flooding, damage irrigation systems, harm aquatic habitat, and limit the use of water for other purposes. Stream quality can be affected many miles downstream from the mine. Before SMCRA was implemented many streams were degraded by uncontrolled sediment from mining. Sediment is controlled through careful planning and a design that incorporates a variety of measures that work together to reduce soil erosion at the mine. Disturbed areas are graded, and some areas terraced, to achieve stable slopes, reduce runoff water velocity, increase infiltration, and divert runoff into drainage channels so that it flows away from unvegetated, erodible areas. Grading along the slope contour and scarify in gun vegetated slopes with bulldozer track marks help prevent erosion by slowing down the flow of water. Runoff from haul roads is controlled by culverts and roadside ditches. Sedimentation ponds or other forms of sediment control are required at all mines to minimize the amount of sediment leaving the site.

Jan 1, 1992

By A. Wahab Khair, S. Jung

"This paper deals with the fracturing process of laterally confined blocks of coal subjected to impact indentation. During the test, blocks of coal with approximate dimensions of 10 in. x 10 in. x 6 in. were laterally confined to predetermined equivalent in-situ stresses and then subjected to an impact indentation by dropping coal cutting bits (various shapes) attached to a known weight from a known height. During the test a number of parameters, namely surface strains (using strain gages), penetration depth (using L.V.D.T.) and acoustic emission characteristics were measured. After the test, the fractured surfaces were photographed with the aid of a camera attached to a microscope. The fracture, its intensity and extended zone within the coal blocks were mapped using sonic techniques. By correlating measured parameters, fractured zones under a given set of test parameters were identified and characterized.INTRODUCTION To improve the understanding of basic failure mechanisms in coal cutting, a better knowledge of fracture and crack regions caused by the indentation in coal is needed. This study reports the detailed experimental procedure used in fracture analysis of indentation experiments on coal specimens using the Acoustic Emission (A.E. hereafter) and sonic techniques. The relationship between microcracking and the inelastic deformation of rock was confirmed by a series of experiments in which the A. E. generated by the cracking in the rock specimen were recorded and the number of events were compared to the strain measurement. (Scholz, 1967).According to fracture mechanism theory, crack initiation in brittle materials such as rocks begins from ""flaws"" either pre-existing or induced by the indentation process itself. Rocks are pervaded by natural cracks and pores, from which numerous possibilities for crack initiation arise (Lindquist, Lai and Alm, 1984)."

Jan 1, 1989

By R. J. Lutton

The U. S. Army Corps of Engineers is seeking empirical slope data from mining companies and other organizations to help establish guides for engineering Judgment in crater excavation for canals and other civil works. Slopes from about 100 open pits and other excavations range in heights to greater than 1000 ft. Factors known or expected to affect stability (and optimum slope inclination) are: geological structural orientation, geological structural ordering, method and technique of blasting, design life of slope, groundwater conditions, depth of excavation, climate, and height. These and other more subtle factors appear to combine and produce an overall effect brought out best on a family of empirical curves relating slope height and inclination.

Jan 1, 1968

By Dever Ashmead

ANTHRACITE was first mined in the Wyoming Valley and sold as an article of commerce in 1808. As some preparation has always been necessary to make it ready to burn, the preparation of anthracite must date back over a hundred years. Two vital factors have determined to a large extent the degree and method of anthracite preparation. These are, first, the character of the beds worked and the methods by which they were mined and, second, the equipment used and practices followed in the burning of the coal. It is not the intention here to go deeply into these phases of preparation as a paper of no mean length could be prepared on the history of either. Rather, the intention here is to point out the main considerations and to show the influence they have exerted on the preparation of anthracite. MINING METHODS AND THEIR RELATION TO PREPARATION In the beginning f the nineteenth century, the coal beds were virgin with the possible exception of some outcroppings that had been worked, to a slight extent, by the Indians. It is known that the American aborigines had a knowledge of the use of this fuel, because when the Wyoming Valley was purchased from them, in 1754, they mentioned the fact that, by selling the land, they would lose their coal.

Jan 9, 1921

By Melina Gamis da Silva

A evolução microestrutural que ocorre durante o processo de laminação a quente pode ser modelada em termos dos tamanhos de grão da austenita e de suas frações recristalizadas ao longo dos passes. Este artigo apresenta uma metodologia que permite a análise da cinética de recristalização e precipitação durante a laminação, com base na composição química do aço e parâmetros do processo. Essa metodologia pode ser utilizada na criação de modelos computacionais. Neste trabalho, as simulações apontaram para a alteração do teor de Nb e da temperatura de reaquecimento da placa como solução para otimizar o processo, resultando em melhorias no produto, ganho de produtividade e redução de custos.

Aug 16, 2017

By G. I. Voiloshnikov, V. E. Dementyev

Wide use of adsorption methods for metal recovery is one of the most important achievements of gold metallurgy of the last decades. Anion exchange resins or activated carbons may be used as adsorbents. This paper presents a brief overview of IRGIREDMET effotts on development, testing and implementation of techno­logical flowsheets using both adsorbent types and attempt to compare their technological properties. IRGIREDMET Institute was founded in 1871 as a laboratory for gold smelting and gold ore testing. In 1930 it obtained the status of the Research Institute. IRGIREDMET functioned as leading research center for gold mining industry in the former Soviet Union. At present it is the Open Joint Stock Company dealing with all s01t of research and design works for gold min­ing (ranging from geology to gold refinery). IRGIREDMET started development of ion exchange technol­ogy in 19641• The first stage of work (1964-1970) including development of principle flowsheet of RIP process was carried out jointly with the Moscow VNIIKHT Institute (All-Russian Scientific Research Institute of Chemical Technology)2• The flowsheet of RIP process is presented in Fig. I and includes the following basic operations: gold adsorption from pulp; washing of loaded resin; acid treatment; thiourea adsorp­tion; gold elution by acid thiourea solution; resin washing to remove thiourea; alkaline treatment of resin; resin washing and gold recovery from eluates by electrowinning. The technology developed and equipment used were tested for treatment of clayey ore of Kuranakh deposit at a pilot plant of the Lebedinsky gold complex ("Aldanzoloto" company, Yakutia, Russia). The pilot plant throughput was 200 t/day. At the same time IRGIREDMET conducted the tests on ion exchange technology for ore and concentration products of oper­ating gold plants and for ores of new deposits. Laboratory and pilot plant tests were done and developed initial data and process design criteria for designing of 15 plans of the former Soviet Union. In the course of this work a great number of newly synthe­sized anion exchangers including strong and weak base resins was studied, the peculiarities of anion exchange resins using two different raw material types ( ores and concentrates includ­ing clayey, carbonaceous, silver bearing, arsenic, antimony and base metals bearing products); some theoretical regularities of adsorption process were investigated; the technology of two stage adsorption of gold and silver from silver gold ore, improved flowsheet for gold elution and resin regeneration, design of adsorption equipment including pulsation columns, design of electrowinning cells were developed; conditioning technology for pulp with complex ion composition prior to gold and silver adsorption was developed, etc.3·8• IRGIREDMET specialists took part in commissioning of practically all the plants in the former Soviet Union using RIP and RIL process including Lebedinsky, Kuranakh, Sovetsky, Karamken, Matrosov's plant and Mnogovershinny plants. Due to this works RIP process became standard technology for Russia and the CIS.

Jan 1, 1998