Search Documents

By MARK J. VANARELLI

Estimating groundwater inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies for estimating steady-state groundwater inflows into deep rock tunnels. The case studies included the Chattahoochee and Nancy Creek tunnels. In this paper, statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations. A semi-empirical procedure was utilized for estimating groundwater inflows into these deep rock tunnels. It is the most widely used method/procedure in the tunnel industry. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels which exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semi-empirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Packer test data plotted in histograms were observed in all cases to be log-normally distributed for the radial flow condition. Modeling using Monte Carlo simulations was observed to be an effective tool for removing irregularities in the distribution of the data and incorporating high-end permeability data to derive reasonable groundwater inflow estimates. This paper is based on the PhD thesis entitled “Improvements to the Current State of the Practice in Steady-State, Groundwater Inflow Estimates into Rock Tunnels based on the Application of Statistical Analysis Methods of Packer Test Data obtained from Exploratory Borings During Geotechnical Site Investigations.”

Oct 9, 2020

By Frank E. Cash, Roy G. Stott

This circular describes four modern change houses of the Lake Superior iron - ore district , all conceived and constructed since 1937. The oldest change house described herein was constructed and occupied in 1938 , yet it embodies the modern improvement of air - conditioning . The purpose of this report is to describe and illustrate improvements with regard to health and safety features combined in the construction , arrangement , ventilation , heating ,lighting , and other features , with the aid of photographs , sketches , and diagrams . The modern change house is a fire - resistant structure in which intermingling of men in mine clothes and men in street clothes , hazardous dust , heat and humidity , crowding , poor lighting , slippery and muddy floors , and inadequate facilities for clothes and for bathing have been largely eliminated . The miner coming off shift at a modern mine no longer faces the elements when he gets off the cage . He travels through a tunnel to the change house , where he is cooled gradually by room temperatures as he passes from the mineclothes section and shower room to the street - clothes room . He is assured of dry clothes when he is ready for them . No longer is he sent out of the change house into a muddy yard to drive away as best he can . The modern change house has an improved parking lot and graveled or concreted walkways from it to the change house entrances .

Jan 1, 1949

By R. Barany

Thermodynamic calculations pertaining to the minerals gibbsite, kaolinite, halloysite, and dickite have been hampered by the lack of adequate heat and free energy of formation data. Previous data for gibbsite were highly uncertain, and there were no data for the other three substances. By use of hydrofluoric acid solution calorimetry, the Bureau of Mines derived heat of formation values from the elements and from the oxides for the four substances, and the data were combined with known entropy values to obtain the corresponding free energies of formation. The results show that gibbsite and halloysite are thermodynamically unstable with respect to the oxides (a- alumina, a- quartz, and liquid water) at 298.15° K,, while kaolinite and dickite are only moderately stable (to about the same degree), The instability of halloysite, in comparison with kaolinite and dickite, results in a 60°-lower equilibrium decomposition temperature.

Jan 1, 1961

By M. Gorman

The Mineral Park Mine is an open pit copper-molybdenum mine located in northwestern Arizona, approximately 74 miles southeast of Las Vegas, Nevada. The property has been owned by the Duval Corporation, Cyprus Mining Company and Equatorial Mining of Australia. Mercator purchased Mineral Park from Equatorial in 2003. Mineral Park commissioned a 25,000 tpd copper and molybdenum concentrator in November and December of 2008. The process includes two stage milling (SAG and Two Ball Mills) fed by primary crushed ore. Metals are recovered in a copper-molybdenum flotation circuit consisting of mechanically agitated roughers and cleaners. The copper- molybdenum flotation concentrate is thickened and further processed in the molybdenum flotation circuit which separates the copper and molybdenum minerals into salable concentrates. The molybdenum circuit also uses mechanically agitated cells. This paper describes the plant and some of the highlights of the commissioning process.

Jan 1, 2010

By AIME AIME

THE PAPER, "Surface Effects on Assay Beads Caused by Metals of the. Platinum Group," presented by J. L. Byers, before the Institute of. Metals Division at the February meeting of the Institute, is the subject of interesting discussion, an abstract of which follows. The original paper is available at Institute headquarters as a Preprint. Member-What assurance have you that the percentage of metals, as stated, is really an accumulation?

Jan 1, 1932

By C. Banff, E. C. F. Hamman, J. Venter

Open pit slope stability analyses for large scale instabilities are often carried out using limit equilibrium, finite element or finite difference computer programs. All of these require empirical estimates of rock mass shear strength when calibrated values are not available, which is a common occurrence. A common method of estimating rock mass shear strength is the Hoek-Brown failure criterion, which often over- or underestimates rock mass shear strength when used in limit equilibrium or elastic linearly plastic slope stability analyses, resulting in published alternative estimates for the coefficients of the Hoek-Brown failure criterion. This paper investigates the differences between limit equilibrium and elastic linearly plastic slope stability analysis based on the Hoek-Brown failure criterion. The investigation consisted of a comparison of 3840 RS2 finite element analysis models completed with strain softening, and 216 Slide2 limit equilibrium models. The models were used to evaluate a methodology to determine equivalent limit equilibrium and elastic linearly plastic shear strength parameters that provide the same stable slope angles and instability back break distances as the more representative strain softening stress analysis methods. This paper presents the methodology and compiles the results into design charts and equations for equivalent limit equilibrium Mohr-Coulomb shear strength parameters, that simplify calibration against actual case studies. The results compare well with older empirical shear strength estimates, however, a detailed calibration of the results against case studies will need to be carried out. The analysis also did not consider pore pressure effects; this is left for future publication.

Sep 1, 2025

By W. L., Yerkes

AN interesting study of the application of air-, conditioning to the problem of mine ventilation and cooling can be found on the Witwatersrand in South Africa. Here there are a large number of deep mines in a relatively small area. Due to the nature of the reef, many mines are working at a depth of 6000 ft. and some have gone down to 8000 and 9000 ft. below the surface. At such depths, even in a country geologically as old as Africa, the virgin rock temperature approaches 110°F. The flow of heat from the- rock to the ventilation air is tremendous though the shaft or drift may have been open to ventilation for some years. In addition, there is the heat produced by machinery, lights, and men at work and the heat of adiabatic compression of air introduced into the mine. The difference in atmosphere pressure between the collar of a shaft and a level 6000 ft. below is nearly 3lb. per sq. in., resulting in an increase in heat content of nearly four B.T.U. per pound of air delivered to the mine at surface. Further the exclusive use of wet mining to reduce the incidence of miner?s phthisis increases the latent- heat content of the air.

Jan 1, 1941

By D. E. Keeley

lntroduction Some years ago it was general practice in Canadian mines to use the best timber available, just as it was cut from the tree. Later, to prevent 'borers' from getting into the wood while stacked in the yard, the bark was peeled off, cleaned up carefully, and burned to eliminate a breeding ground for these and other destructive insects. This practice of good housekeeping also decreased the hazard from fire in scattered bark. A few years after damage by borers had been minimized, it became apparent that increased temperatures in the mines, occasioned by deepening operations, were being accompanied by rapid growth of fungus and by decay in timber underground, greatly shortening its life. In places on upper levels where the air temperature was below 50 deg. F., untreated timber retained a large proportion of its strength for ten or more years. In other places on these levels, however; its life was short and it developed much dry rot and merulius lacrymans. In these latter places and on lower levels in the mine where temperatures ranged from 50 to 60 deg. F., approximately, the wood became infested with extensive growths of this white fungus. This development was accompanied by the production of millions of spores. Spread of infection was due mainly to the transfer of spores from the warm lower levels to the cool upper horizons by upcasting ventilation currents. So serious did this become that about twenty years ago Lake Shore, Hollinger, and McIntyre Mines decided to investigate the use of wood preservatives and the plant necessary to treat timber.

Jan 1, 1949

By Kunwar Pal, S. K. Tyagi, A. K. Pandey

"This study deals with the performance evaluation, technical and environmental aspects of different cookstove models (NIRE-02, NIRE-03 & NIRE-04). These cookstove models were designed, fabricated and evaluated following Bureau of Indian Standards (BIS) and their performance was compared from technical and environmental points of views. The theoretical efficiencies of all the cookstove models are found to be in good agreement with the experimental one. Also, the overall performance of these models is found to be in the order of (NIRE-04 > NIRE-03 > NIRE-02) which is also observed to be much better than that of the traditional cookstoves being used by the people in most of the developing countries around the world. The CO2 emission reduction from these models is found to be between 2.0-3.0 tons per household annually which is ultimately in good agreement with the experimental values.IntroductionMore than 2.5 billion people around the world depends on the biomass based resources for cooking and heating applications which includes wood, cattle dung, charcoal and agriculture residue [1,2]. Generally, people of rural area cook their food on unvented open fire, which burn biomass fuel inefficiently besides it creates many thermal and environment pollution hazardous causing health problems in the women and girl children due to more exposure of emissions. Also the consumption of biomass is very high as compared to the fossil fuels due to the fact that the large population of the developing countries lives in the rural area than that of in the urban area. It is estimated that about 3% of the diseases are caused due to incomplete combustion of biomass, which results in the around 1.8 million premature death every year including around 0.9 million death under five year of their age [3,4].Ramanathan and Carmichael [5] recently found that the black carbon of unburned smoke is playing a major role in global warming. The emission factors for different combinations of fuel and stove tested in China for direct and indirect GHGs as well as other airborne pollutants such as, CO2, CO, CH4, TNMHC, N2O, SOx, NOx, TSP etc. for a typical set of operating parameters [6]. The improved biomass cookstove technology came into assistance which is technically feasible, socially reliable and economically viable [7, 8]. The improved biomass cookstove not only reduces pressure on the biomass resource, but also reduces the environmental pollution and also minimize the time required for collection of fuel wood [9, 10]. Sharma et al. [11] emphasized on the adoption and large-scale propagation of efficient stoves to improve the health of rural women and to reduce the consumption of firewood and environmental pollution."

Jan 1, 2014

By V. F. Parry

"INTRODUCTION During the war period the Bureau of Mines expanded its investigations on western coals principally in connection with Investigations of raw material resources for western steel production. Owing to the expansion of the steel industry, there was some concern regarding the availability of suitable coking coals; end because of the potential steel shortage, the production of sponge iron, using the lower-rank fuels, was considered. Work was conducted by the Bureau of Mines on exploration projects and on testing of coals both at the Central Experiment. Station at Pittsburgh, Pa., and at the Bureau of Mines Station at Golden, Cole.The results of these investigations are being published by the Bureau in several reports of investigations and technical papers. In making this resume of coal investigations, the work done by the Bureau of Mines at Pittsburgh in the Mining and Coal Carbonization Sections will be discussed and the investigations at Golden described in greater detail.INVESTIGATIONS OF WESTERN COALSThe Mining and Coal Carbonization Sections of the Coal Division, Bureau of Mines, under the supervision of A. L. Teeny es and J. D. Davis, respec¬tively, conducted many field investigations to locate and evaluate new sources of coking coals. Drilling explorations were made in Colorado, Wyoming, Utah, New Mexico, and Washington and revealed two important new reserves of coking coal. The first one studied was the Willow Creek bed at Kemmerer, Wyo., which was reported in 1945.3/ A recoverable reserve estimated at 11,200,000 tons was blocked out, and samples of coal were extracted for coking tests. The coking properties of the coal were not quite equal to those of Sunnyside coal, but it was indicated that a 50-percent blend of the Willow Creek with Lower Sunnyside will produce a satisfactory metallurgical coke based on Columbia steel standards."

Jan 1, 1948

By Robert L. Anderson

A shaft or slope bottom is that portion of a mine that is contiguous to the bottom of the main hoisting shaft or slope. It includes the terminal tracks for loaded-and empty-car storage, locomotive run-arounds, locomotive shops, charging stalls, supply rooms, pump rooms, waiting rooms, and offices for dispatcher, weighmen, and foremen. This paper will deal principally with the arrangement of tracks and the handling of cars on the bottom, but includes other data that may be affected, directly or indirectly, by the bottom lay-out. All of the mines discussed are being operated in comparatively level coal seams.

Jan 1, 1937

By Alan J. Fejes

As part of its mine subsidence research program, the Bureau of Mines and the American Electric Power Co. cooperated on a study, conducted at the Price River Coal Co. No. 3 Mine, directed toward developing the capability to estimate the surface subsidence resulting from longwall mining in a geologic, topographic, and mining environment common to coalfields in the Western United States. Subsidence was monitored at the No. 3 Mine over two adjacent longwall panels. The subsidence study area was reduced when the two planned panels were reduced in length because of equipment failure and a mine fire. Subsidence was measured for 21 months. Subsidence continued for 6 months after mining had been completed. A maximum of 2.2 ft of subsidence occurred over the two longwall panels mined at an overburden depth ranging from 300 to 1,500 ft.

Jan 1, 1986

By F. D. Cannon

"In metal and nonmetallic mineral mines during the 15-year period 1911 to 1925, 30.17 per cent of all fatalities and 16.57 per cent of all injuries were caused by falls of rock or ore from the back or roof or from the wail; 1.24 per cent of the fatalities and 11.05 per cent of the injuries were caused by rock or ore while loading at the working face; 6.66 per cent of the .fatalities and 2.49 per cent of the injuries resulted from men falling down 3 chute, winze, raise, or stope; and run of ore from chute or pocket caused 1.48 per cent of the fatalities and 1.93 per cent of the injuries.3 Hence, accidents due to falls of men and material caused. 39.55 per cent of the fatalities and 34.05 per cent of the injuries in these mines. Accident prevention can best be assisted by each company's preserving complete records of accidents classified according to cause and rate per thousand or 10,000 shifts. A systematic method of recording accidents and the employment of graphs or charts will be helpful to the company safety department in analyzing the cruses of accidents. The purpose of this publication is to analyze data on accidents caused by falls of men and material in metal -mines of the United States, and to suggest methods of preventing or reducing such accidents."

Jun 1, 1929

By H. M. Woodrooffe

This paper deals with the laboratory facilities at the Mines Branch for carrying out research in the industrial minerals field, and also reviews current programs in ceramics and construction materials, in non-metallic minerals and in the milling of industrial minerals. It then discusses the application of these pro-grams to industrial problems.

Jan 1, 1967

By T. Dlokweni, M. Bester, C. Koegelenberg, I. Basson

Certain degrees of safety, economic, and financial risk are implicit in any mining operation. At Thabazimbi Mine, slope stability was one of the major sources of risk, largely due to data uncertainties. Consequently, a risk-based approach in slope design was followed. On 6 June 2015, a slope failure occurred in Thabazimbi Mine’s Kumba pit, involving approximately 65 million tonnes of rock failing into the pit and the valley below. Although the failed mass moved rapidly and resulted in a run-out distance of approximately 900 m, controls had been put in place to successfully evacuate all personnel. Risk assessment during the onset of failure supported the decision to not compromise the safety of personnel in any way, leading to unavoidable equipment loss. This contribution presents the failure as a case study in the context of a risk-based approach to slope design as well as the importance of implementing geotechnical controls to effectively manage slope instability risk. Furthermore, a comprehensive back-analysis was performed, on a fully constrained 3D model, utilising 3DEC software, to gain insights into the failure mechanism. In conclusion, lessons from the Thabazimbi slope failure are valuable as they demonstrate the importance of following a risk-based approach in slope design to effectively manage safety and financial risk in open pit mines.

Sep 1, 2025

By Uday Kumar

This paper presents details of an availability study for a fleet of diesel engine operated load-haul-dump (LHD) machines used in a Swedish mine. For the purpose of this study, the LHD machines have been considered as a system comprised of many subsystems like engine, brake, transmission, etc., in series. As availability is dependent on both the reliability and maintainability characteristics of the system, together with reliability, the concepts of maintainability are also discussed. The need for exploring the data for the presence of any structure, which is very common in repairable system data sets, is emphasized with suitable examples. Simple graphical techniques are used for verifying the independent and identically distributed (IID) assumption for the data set. The error introduced due to the use of the exponential distribution in place of more appropriate distributions in estimation of availability and reliability characteristics is analysed.

Jan 1, 1989

By Kenneth Eltschlager

Blasting represents the highest risk of any surface coal mining activity that could result in injury and/or property damage off the permit area. In addition, blasting related issues e.g. flyrock, vibrations, air blast, etc., are responsible for a large percentage of citizen complaints. Thorough and consistent regulation of individuals certified to conduct blasting by the Office of Surface Mining Reclamation and Enforcement in Federal Program states and on Indian Lands under Federal jurisdiction is vital, as it serves to: facilitate coal production to meet the nation’s energy needs; protect people and property on and adjacent to Federal mining permits; form a basis for states to grant reciprocity certificates to Federal blasters; and be a positive example to primacy states. OSM issues Federal blaster certificates for blasting on Federal surface coal mine permits. The certification program includes experience, training and testing components similar to many of the states. But where a state program may focus on the specific blasting applications within its boundary, the OSM certificate requires a very diverse test to cover all potential blasting applications and products across the nation. Therefore, the Federal certificate is a good surface mining credential for blasters anywhere in the United States.

Jan 1, 2010

By N. L. Kozlinsky, B. W. Gandrud

"The Marvel mines 1 and 3 of the Roden Coal Co. are located in the Cahaba field in Bibb County, Ala., nearly southwest from Birmingham, an airline distance of roughly 30 miles. The coal of the Clark seam at this point has some coking properties, but at present it is sold exclusively as a domestic and steaming coal.This paper, which is the second of a series on the washability of Alabama coals, like its predecessor dealing with the Mary Lee seam,5 contains screen-sizing and float-and-sink tests of a representative sample of the raw slack, and slotted-screen tests showing the proportions of flaky particles in certain selected sizes; inasmuch as this coal is not used for coke manufacture, no crushing tests have been made. These data have been obtained in connection with an exhaustive study of coal preparation in Alabama, now being conducted by the United States Bureau of Mines and the University of Alabama with the cooperation of the different coal operators. As the work progresses, other papers will follow containing further data on Alabama coals and giving results obtained in preparing these coals by various methods.The only published investigative work on the Clark seam is that of Forbes,6 who gives a number of sections of this seam in Marvel No. 3 mine with proximate and ultimate analyses of face samples taken in the mine and also some analyses of delivered coal.The available information on this coal indicated that the preparation problem was one of ash reduction. In order to substantiate this information a complete analysis of the 3/4 by 3/16 inch size, and sulphur determinations and ash-fusibility tests of the float-and-sink fractions have been made; these results are given in Tables 1 and 2. As these results also indicate that the preparation problem is one of ash reduction, the tests and discussion have been devoted to that subject."

Jun 1, 1930

By A. A. McCloskey

APPROXIMA TEL Y 95 percent of Waite-Amulet's Lower A orebody will be mined by diamond-drill stoping. This method of stoping was developed, and has been successfully applied, at the Noranda mine in recent years(1) and is now used in several base-metal and gold mines in north-western Quebec and in other parts of Canada, South Africa, and Australia. The purpose of this paper is to deal with the features of the Lower A ore-body which led' to the adoption of this method of stoping, and in addition to give a general description of stope layout, stope development, main haulage development, chutes and grizzlies, diamond drilling for stope blasting, diamond drilling and equipment, primary blasting, secondary blasting, haulage and loading, ore pockets, pumping and drainage,. and shafts at Waite Amulet. Figure 1 is an isometric projection of the orebody, illustrating the mining system. The factors that led to the adoption of diamond-drill stoping of Lower A orebody are as follows: (1) Safety.0 (2) Size and shape of the orebody, and depth of the orebody below surface. (3) Strength of the hanging-wall, footwall, and sulphide ore. (4) Continuous ring-drilling from sub-level drifts, with no delay for blasting. (5) Large-tonnage blasts at the end of Saturday afternoon shift, after ali men are out of the mine. (6) Sub-levels may be retreated from top to bottom simultaneously, or lower sub-levels may be retreated first without any change in the ring-drilling la yout. (7) Large stopes up to 100 feet wide can be mined, leaving substantial pillars up to 60 feet in width, which may be partially recovered by âiamond~drill stoping or by other stoping methods. (8) A large tonnage may be drilled-off in advance of blasting, but only a supply of unoxidized ore for flotation treatment is blasted. (9) Better ventilation during working shifts. (10) Gravity flow of all broken ore to grizzlies located in the footwall of the orebody. (11) Electric blasting by a crew of two men.

Jan 1, 1941

By E. G. Erspamer

Laboratory investigations were made by the Bureau of Mines on ore containing the sulfides of both mercury and antimony to develop a method or methods for the economic recovery of mercury metal and the concurrent recovery of antimony as metal or salts,. If standard mercury-recovery techniques are applied to such ores, the antimony content interferes with the effective production of mercury metal; further-more, the antimony is lost. This report presents the results of tests on a sample of cinnabar-stibnite ore from the Red Devil mine near Sleitmute, Alaska. Red Devil ore was chosen for the investigation because it is purported to be typical of ores of the Kuskokwim River area, which, in their aggregate, constitute large potential reserves of mercury and antimony. Studies included petrographic, spectrographic, and chemical analyses, gravity-separation tests, bulk flotation of mercury and antimony sulfides, differential flotation, leaching, and furnacing of crude ore and of flotation concentrate.

Jan 1, 1956