Search Documents

By Timothy W. Ellis, John A. Howes

The production of lead-acid batteries is defined by a closed-loop product life-cycle. Active material and grid alloys converge on an adaptable specification that improves both performance and recyclability. This mapping of product requirements for lead-acid batteries has taken over 80 years to develop. But, as the use of batteries made with other chemistries continues to grow, the need for a comparable life-cycle management process becomes increasingly apparent given societal needs to manage raw materials, e.g. the European Union Battery Directive recycling targets. What has taken more than 80 years for lead-acid to evolve in a closed-loop paradigm must now be accomplished in less time for batteries using other chemistries and technologies. End-of-life costs are embedded in the product cost of lead-acid batteries. However, end-of-life costs are not reflected in the product cost of batteries made with other chemistries. Those costs are borne by other constituencies with often inefficient and environmentally damaging results. Lead-acid is a materials technology management model for other products.

Mar 1, 2017

By J. Andrew McGlenn, Greg Emslie, Murray Gant

The Second Narrows Water Supply Tunnel will ensure system reliability in the event of a major earthquake and increase the Greater Vancouver Water District’s capacity to meet a growing population’s longterm needs. It includes a bored tunnel between two deep shafts located in North Vancouver and Burnaby, BC, Canada. The support of excavation for the 16-meter-diameter (52.5 ft) TBM launch shaft consists of 83-meter-deep (272 ft) unreinforced concrete slurry walls. This paper discusses challenges encountered during construction of the launch shaft slurry walls, namely excavation methods and slurry loss, and mitigative solutions implemented to successfully complete the shaft with minimal impact to project schedule.

Dec 1, 2022

By David Wilshaw

Continuous Surface Wave (CSW) testing has been the “next big thing” in ground characterization for the last 25 years. The technique uses surface geophones to measure the speed at which Rayleigh waves (generated by a vibratory source) travel through the ground over a range of frequencies. The velocity at which surface waves travel through the ground is directly related to ground stiffness; the velocity of shorter wavelengths is influenced by the stiffness of shallower soil layers, while the velocity of longer wavelengths is influenced by the stiffness of deeper layers. Measuring the surface wave velocity over a range of frequencies, therefore, allows a stiffness / depth profile to be produced. Using the small-strain stiffness data measured by the CSW technique greatly improves the accuracy of simple limit state analyses; the data are also of sufficient quality for use in Finite Element modelling. Nonetheless, the technique has suffered from a perception of high cost, low productivity, and poor repeatability. An improved Advanced Continuous Surface Wave (ACSW) testing system has been developed by Ground Stiffness Surveys in the United Kingdom, has been deployed there commercially for several years, and is now available in the United States. ACSW uses an automated electronic control system that generates vibrations (from a purpose designed and manufactured portable seismic “shaker”) at different frequencies, measured across a 3m (10-foot) array of geophones, linked to a robust data acquisition and analysis software package. The range of applications in geologic and geotechnical site characterization includes rapid preliminary non-intrusive site assessments (utilizing published soil correlations); stiffness profiling to detect discrete layers (such as a variation in rockhead); average stiffness profiling for earthwork or ground improvement control testing, Working Platform stability assessments, foundation settlement analysis, rock quality and rippability assessments, and void detection.

Oct 1, 2022

By V. Svalbonas

The process of grinding mill quality assurance brings with it associated truths and myths. When the mill quality assurance process took its first great steps forward in the late 1970s and early 1980s, they were in response to the conditions existing, in our industry, at those times. In the late 1990s, we are faced with different conditions, and problems, and need fresh solutions. Yet the system developed for the early 1980s has produced no new approaches for the late 1990s, becoming instead more hardened and entrenched. This lack of development and actual resistance to research is now costing the industry significant amounts of money in late start-ups and useless scrap loss.

Jan 1, 1999

By Michael B. Mooiman, David J. Kinneberg, Philippe Cettou, Leo W. Simpson, Pierre Ramoni

"The demand for high purity precious metals began with certain industrial applications having uncompromising requirements for quality and performance. As industrial uses proliferated and as the jewelry industry became increasingly sophisticated, the demand for high purity gold has reached the point where 99.99% is now the standard in the marketplace. A similar evolution is expected for other precious metals.In this paper, we examine both the production and use of high purity precious metals, specifically gold, silver, platinum and palladium. After defining what is meant by ""high purity"", we discuss the various analytical techniques used for measuring impurity concentrations. Next, we review process strategies employed by extractive metallurgists to produce high purity precious metals. Lastly, we describe some of the principal applications for high purity materials including thick films, thin films, bonding wire, thermocouples and jewelry manufacture.Precious metals have unique physical properties that, despite their expense (and the ever-continuing search for more economical alternatives), make substitution difficult if not impossible. These physical properties are dramatically affected by small concentrations of certain impurities. As long as manufacturers continue to demand quality and performance, there will be a need for high purity precious metals.IntroductionIn the precious metals industry, the qualifier ""high purity"" describes any specification over and above commodity grade. High purity specifications delineate lower limits on overall metal purity or upper limits on individual impurities or both. Sometimes, if these special requirements become commonplace, either because of improved refining technology or because of market pressures, yesterday's ""high purity"" material becomes tomorrow's commodity. This transition is now occurring with gold bullion and probably will soon occur with platinum and palladium as industrial use of these materials grows."

Jan 1, 1998

By Richard A. Levins

The imposition of non-market regulations, such as the proposed SO2 standards for coal combustion, will typically lead to less efficient (thus more costly) production in a free enterprise system. For the coal industry these increased costs will occur in several ways, among which are mining less accessible low sulfur reserves and transporting low sulfur coal to distant markets. There are, of course, social benefits of reducing the S02 emissions from the use of high sulfur coal. The social benefits include decreased health risks, reduced damages to property, and certain unmeasurable benefits associated with the aesthetic appeal of clean air. Proponents of Federal S02 standards argue that the benefits gained from reduced emissions will exceed the costs borne by the coal industry and society in general in meeting the regulations. The purpose of this paper is to investigate the degree to which costs of meeting future energy demands from coal will change under different sulfur standards. No attempt is made to estimate the benefits of imposing regulations. Specifically, the impact of SO2 standards on the private costs of meeting regional coal demands, the competitive positions of the nation's major coal producing regions, the degree to which strip mining as opposed to underground mining will be feasible, the amount of coal being processed, and the amount of coal transported over major rail routes will be analyzed.

Jan 1, 1976

By J. L. Jambor, J. E. Dutrizac, J. B. O'Reilly

The present-day metallurgical community is quite familiar with the use of jarosites [MFe3(S04)2(0H)6 where M = K, Na, NH4, Ag, 1/2Pb, etc.] as a means of controlling iron, alkalis and sulphate in hydrometallurgical circuits. This modern precipitation technology has found an increasingly widespread application in the zinc industry111 and is gradually also being extended into the hydrometallurgical processing of copper and cobalt121 . The chief advantage of jarosite precipitation is that the iron precipitate settles and filters well, and gives low losses of divalent metals in the washed residue. Although this jarosite precipitation technology was developed only within the past twenty years, man's involvement with jarosites extends back to antiquity, and jarosites have played an important role as a source of silver in several ancient metallurgical centres. In the early days of this century, argentojarosite was an important local source of silver at the Tintic Standard mine, Dividend, Utah, where over 200 000 oz of silver were recovered from highgrade natural jarosite over a three-month period 131 . At the Matagente mine in Peru, pockets of argentiferous plumbojarosite up to 40 m thick were mined and processed by the Indians prior to the arrival of the Spaniards14-51 . In Cyprus there are vast jarosite deposits associated with the ancient mining sitesl51 , but exploitation of these jarosites has been insignificant because of their low silver values. The most extensive mining of silver-bearing jarosite, and certainly the oldest documented instance of such jarosite exploitation, was in the vast pre-Roman workings at Rio Tinto, Spain. This mine, the greatest single miningmetallurgical site currently known from the ancient world and also the oldest site of more or less continuous metal production, has witnessed many metallurgical firsts. Aside from the initial processing of jarositic ores for their silver values, the development of large-scale hydrometallurgy also seems to have occurred at Rio Tinto. As early as 1737, copper was recovered by cementation on scrap iron from the mine waters at Rio Tintol51 . Large-scale heap leaching of calcined ore commenced with the British operations in 1876 and, by 1900, raw pyrite was heap leached to recover associated copper values161 .

Jan 1, 1999

By Eldon C. Pattee

THE BUREAU OF MINES began an investigation of tungsten resources of Montana in September 1953. This report presents information obtained from July 1955 to September 1957 on tungsten deposits in and near the Mount Torrey batholith. The batholith comprises part of the Pioneer Mountains of Beaverhead County in the southwest corner of Montana. Included in the report are assays and preliminary-examination data on 22 properties. Tungsten minerals are known to occur in 19 of the properties. The major producer is the Brown's Lake mine which has produced more than 625,000 tons of ore. Nearly all of the deposits are in the Lost Creek, Utopia, and Bald Mountain mining districts along the east and south margins of the Pioneer Mountains. The districts are less than 27 miles from Dillon, Mont.

Jan 1, 1960

By Jack Mantel

The goal of this 42-month contract was to increase safety in low-seam underground coal mines through development and in-mine evaluation of a temporary roof support system for roof drills and floor-riding operator compartments for a loader and shuttle car. The program was performed in three phases. During Phase I, state-of-the-art canopy technology was investigated, and preliminary design and mock-up evaluations were performed for temporary roof supports for single-and dual-boom bolters and for transverse-mounted floor-riding canopies for a shuttle car and coal loading machine. The shuttle car and loader canopies were approved for further development, and the design, fabrication, testing, and certification were completed in Phase II. In Phase III, the Bureau of Mines furnished an FMC 6L shuttle car fur use in the evaluation of the canopy for 45 shifts. The shuttle car canopy was evaluated at Virginia Crews Coal Company in West Virginia. Efforts to secure an evaluation site for the loader canopy were unsuccessful. The loader canopy was shipped to Bruceton for possible future evaluation.

Jan 1, 1985

By Norman A. Jull

"IntroductionThe scope of this paper is intended to deal mainly with cyclones in grinding circuits. However, the section on Cyclone Equipment, contains more general descriptions, to cover most of the cyclones used in mineral separation plants.Cyclones as heavy media separation vessels are discussed by Mark Freberg (this volume). Their use in tailings deslirning is discussed by P.C. Lighthall, eta/. (this volume).Cyclone EquipmentCyclone TerminologyApexObviously, the apex of a cone is the smallest end. However, with cyclones the term is usually used for the fitting which is attached there to control discharge of the underflow stream.Note that the cyclone need not be so mounted that the apex is the lowest point, although that is the most common method. Keeping the apex below the rest of the cyclone helps avoid plugging when the underflow contains very large particles and the tonnage of underflow solids can fluctuate.Various devices for adjusting apex diameter or otherwise controlling the underflow are discussed later under ""Cyclone Construction"".BypassingThe transport of a portion of feed slurry directly to underflow so that classification is bypassed by that portion of feed.This action is fundamental in any hydraulic classification, whether gravity or centrifugal, because the large particles going to underflow have some void volume between them, which remains filled with feed slurry.D50By definition, D50 is that particle size which has an equal probability of going to overflow or to underflow.It is calculated by drawing a curve of recovery vs particle size and noting the size at which 500Jo recovery occurs.This may be done equally with corrected or with gross recovery (see below) and the resulting value should therefore be identified as d50c (corrected d50) or as d500 (gross d50).Note also that it is common in industry practice to plot size analysis data on the retained size rather than on the average of passing and retained (the middle of the size band). To portray sizing alone it makes no difference, but to read a D50 value off a curve of corrected or gross recoveries, it is essential to plot those values on the average size of each band."

Jan 1, 1989

There are many compelling reasons why correct sampling schemes should be standard practice in the mining industry, yet there are numerous examples where poor sampling practices are known to exist in the business yet permitted to continue. It is not just technical issues that can be ascribed to the reasons for the continued use of incorrect methods. This paper proposes non-technical reasons why incorrect sampling practices continue, and identifies potential ways to overcome them.

Mar 1, 2010

By M. R. MacIver, M. P. Pawlik

"An image analysis method based on chord length distributions is applied to the batch settling of polyacrylamide flocculated kaolin suspensions. Two features of the interaggregate void space, the void chord length distribution mean and the white-to-black distribution ratio are extracted from an image series obtained over the two hour settling experiments. This approach produces three signal values, from two different probability distributions that can be measured as an indication of underlying sediment bed density and aggregation state. Further work is required on the physical interpretation of the signal, the image acquisition conditions, and the parameter selection methods. It is suggested that this chord length based feature extraction technique may be a useful signal to monitor during batch settling or thickening.INTRODUCTIONFew in situ techniques are available that can be used to directly measure aggregate properties within sediment beds in thickeners or secondary settlers. Typical process variables monitored include rake torque and height, bed level and pressure, feed rate and density, underflow rate and density, settling rate, and overflow turbidity; yet these process variables are only weakly related to process dynamics (Concha et al. 2014). Additional process monitoring signals, based on the direct measurement of aggregate properties could improve solid-liquid separation control and allow the extraction of more detailed information from batch settling experiments.Several optical methods exist for measurement of moving suspensions of aggregated solids in the dilute concentration regime, such as focused beam reflectance measurement (Peng and Williams 1994), and the turbidity fluctuation method (Gregory 1985). In the more concentrated region of a thickener, acoustic backscatter penetration and attenuation measured with an acoustic probe and changes in the underlying solid concentration in the highly concentrated, near-bed region of a thickener as a function of height and time (Hunter et al. 2012). While machine vision for froth monitoring has been thoroughly studied with at least five commercialized technologies (Aldrich et al. 2010), its’ application to the study of thickening has been limited."

Jan 1, 2016

By John J. Sammarco

The U.S. Bureau of Mines is conducting research into computer-assisted mining, which requires investigation of new techniques for development and application of computer-based technologies. Today's technology can require significant effort in software development, as has become evident in the early stages of this Bureau research. Technologies for software automation, such as computer-aided software engineering (CASE), are available. This report explores CASE, its general features, and its importance in software development. Information is presented to assist in selection and application of the variety of CASE tools and methods for automating various stages of software development. When evaluating CASE for use, it is important to examine tools that support an organization's existing methods of software development. Support for existing hardware platforms must also be examined. Merely selecting a "good" CASE tool does not insure success. Thorough evaluation of implementing CASE is also critical. Subjects to evaluate for CASE implementation include organization culture, support from management and end users, training resources, and pilot projects. Organizations that benefit the most from CASE evaluate CASE features with respect to their needs and they properly implement CASE.

Jan 1, 1990

By E Kabwe, M Karakus

Deep hard rock underground mines tend to experience high stress as such drives exhibit dynamic responses attributed to a rock burst variant (strainburst). This dynamic behaviour is difficult to predict, and every effort is made to devise the appropriate dynamic support system for its associated failure restraint. This paper outlines the back analysis and the support scheme design for an underground decline that exhibited damage from a dynamic strainburst occurrence. It employs a decline section that experienced a dynamically loaded strainburst that initiated rock fragment ejections. The procedure involves a preliminary structural analysis, a seismic intensity measure, and a rock mass simulation to determine the static stress concentration and ground support system response. The numerical simulation is conducted in FLAC3D which employs the advanced strain-softening IMASS constitutive model governed by two Hoek–Brown (HB) bounding yield surfaces. To account for the post-peak brittleness response associated with strainburst the plastic strain multiplier () is adjusted to 0.0 < < 1.0. The back-analysis shows that the occurrence was initiated by a low-intensity seismic wave that superimposed an extra stress component to the initial static stress which triggered rock fragment ejections. Additionally, the appropriate support scheme comprised of Weldmesh, Fibrecrete, static (split set) and yieldable (Kinloc) reinforcements is recommended and implemented. Thereafter, the bolt’s efficiency is evaluated based on the axial force and elongation capacities and then compared with the published bolt performance data. The evaluation results show that the maximum bolt axial force (0.1 per cent) and elongation (0.006 per cent) are below the designed capacity and rupture strain.

Nov 29, 2022

By H. Colijn

Weight may be defined as the gravitational attraction or earthpull on a body (mass). Thus, from a practical viewpoint, a scale or other form of weighing device is a mans for determining mss. Weighing devices fall into two principal categories: (1) gravimetric; and (2) non-gravimetric or nuclear devices. At present, after many centuries of use, the effect of gravitational force as a meas¬ure of mass in industry and commerce remains by far the most common method for mass (weight) determination. Non-gravimetric methods are just becoming established in the industry. The general trend is toward weighing materials on the Trove. The predominant advantage of continous weighing over batch weighing operations is its ability to handle large tonnages without interrupting the material flow. The accuracy and reliability ability of continuous weighing equipment have improved greatly over the past decade. However, static weighing equipment still outsells continuous weighing equipment, because it is considered more accurate. Batch weighing can also produce a continuous weighed delivery through automation where the process requires it. In caparison with continuous weighing devices, such as belt scales, the batch-type scales have same inherent advantages affecting their accuracy. For example, weighing 300 lbs. per minute on a belt scale may mean that only 3 lbs. will be on the scale mechanism at one time. In order to obtain a scale accuracy of 1/2%, the sensitivity must be at least 1/2% of 3 lbs. or 1/4 oz. On the other hand, a batch scale may discharge a 300 lbs. load every 60 seconds through a timing mechanism. An accuracy of 1/2% can be easily obtained with a sensitivity of 1/2% of 300 lbs. or 24-oz.

Jan 1, 1970

By Karin Bäppler

Lyon with half a million inhabitants is the third largest city in France. Urban agglomerations such as Greater Lyon demand intelligent underground solutions for the freedom of mobility of its inhabitants. The city and metropolitan area of Lyon provide an example of a city strategy adapted to the changing needs due to demographic and living standard trends. The Lyon Metro Line B with a length of 2.4 km is one of the strategic projects with regard to city planning and future mobility. The paper will highlight on this special area of application in singular diverse geology with sophisticated mechanized tunnelling technology.

Jun 13, 2021

By J. S. Rapp

This report is based on existing reports and recently gathered field data. It discusses mineral resource potential of Tertiary playas in the Fort Irwin region. An estimated 1.3 million tons of measured salt "reserves", and 20 million tons of indicated salt resources, have been identified north of the fort. Other indicated resources include 300,000 tons of celestite, 800,000 tons of gypsum, and 10 million tons of selenite. Zeolitic tuff was mined south of Fort Irwin from 1978 to 1984, and unexplored occurrences are widespread. Calcium-bentonite is mined near Barstow, and more may exist, including valuable sodium-and lithium-based bentonites.

Jan 1, 1992

By Gordon O. Prickett

In two case studies we look at strategies of acceptance that the analyst can employ to gain entrance and to see his problem solution out to use. The first example comes from metal mines. The problem area was excessive usage and cost of wear parts in the concentrator and an atmosphere of crisis over frequent and unexpected breakdowns. The second case pertains to coal exploration. Better methods were being sought for representing coal quality in developing reserve tonnages. The first strategy is - Develop a detailed Human Impact Statement. The second strategy is - Write down in plain language with the keeper of the problem what he will consider as success in dealing with his problem.

Jan 1, 1978

By W. G. Pariseau

Recent advances in rock mass mechanics and computational technology now allow for stability analysis of excavations in "wet" mines where mining-induced changes in rock mass deformation and fluid flow are coupled and time-dependent. All the usual dry mine parameters including the premining stress state and rock mass properties are taken into account, in addition to water pressure and flow in jointed, possibly porous, rock masses. Finite element analyses of shafts and tunnels as circular, elliptical, rectangular and arched-rectangular hole shapes excavated in an initially stressed and pressurized rock mass indicate that the usual guidelines for optimum shape and orientation of single openings apply. Here, optimum means maximizing the minimum wall safety factor, or equivalently, minimizing the peak stress concentration. The results also show that failure originates in elements at the wall and that the minimum safety factor at the wall in the wet case is always less than the dry case regardless of drainage time allowed.

Jan 1, 1995

By Joseph L. Buckley

A total of 55 conveyor belt fire tests were conducted in the Bureau of Mines Fire Test Gallery, located at the Factory Mutual (FM) Fire Test Center West Glocester, R.I. The objectives of these tests were to: 1) determine the fire resistance and burning characteristics of various conveyor belt materials under simulated mine conditions; 2) provide essential data for designing a reliable bench-scale conveyor belt fire resistance test; and, 3) determine fire test conditions that will discriminate between low, moderate and high fire resistant materials. Belts, representative of those which mold he found in underground coal mines were examined under n umber of experimental conditions which included; ignition intensity; air flow rate; ratio of belt bright (h2) to overall gallery height (h1); exposure time; and, belt width. It was found that fire propagation could be achieved for some "fire resistant" belts (complying with the present Schedule 2G standard for approval) when exposed to an Ignition source of =6000 Btu/min for a 15-min period at a belt height ratio of 01.66. There appears to be a dependency of flame propagation on air flow rates and belt width, although the tests performed do not provide a quantitative trend. Recommendations are made for additional work to resolve some anomalous date and to fill voids in the rest program.

Jan 1, 1978