Search Documents

By Yuting Xue, Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Khaled Mohamed

Rib brows present a significant safety hazard in underground coal mines in the United States. To address this issue, researchers at the National Institute for Occupational Safety and Health (NIOSH) and Missouri University of Science and Technology (MST) are developing a practical tool to assess both the potential of rib brow formation and the stability of any formed brows. As part of this effort, a monitoring study was conducted to assess the potential for rib brow formation in coal pillar ribs. This study was conducted in a room-and-pillar coal mine where coal pillar ribs are prone to developing rib brows. Although no rib brows formed in the instrumented pillar, data from monitoring and visual observations provided valuable insights into the loading mechanisms impacting the instrumented pillar. These findings helped identify factors that may reduce rib brow formation, including the cavability of the roof in mined areas, the applied rib support, the strength of rock partings, and the overall integrity of the coal seam. The scientific findings published in the case study aid in assessing the potential of brow formation, offering additional evidence for the need to improve rib control methods in underground coal mines.

Feb 1, 2025

By L. A. Wilson, P. J. Root

The relative costs of heating a reservoir by steam injection and by combustion have been examined. The comparison was based on a model similar to that proposed by Chu.' The cost of boiler feed water, the price of fuel, pressure and plant capacity were parameters in determin-ing the costs of air compression and steam generation. The analyses compare the cost of heating to the same radius by the two methods. Results suggest that the two primary factors for comparison are the price of fuel and the amount of crude burned during underground combustion. The cost of fuel has a greater effect on the cost of heat from steam than it does on its cost by combustion. As a result, analyses indicate that when the price of fuel is low, steam may be unequivocally cheaper than air. The influence of heat loss is such, however, that as the heated radius increases combustion becomes relatively more competitive depending upon the amount of crude burned. This implies that steam may be cheaper for small stimulation jobs (huff and puff) but combustion may be more economically attractive for heating large areas (flooding). INTRODUCTION Use of thermal methods of recovery is an accepted fact today. After an induction period of several years, processes are being widely used that involve reservoir heating to augment recovery. Of the several techniques, steam injection and forward combustion appear to be destined to dominate the field. Although the objectives of both are the same, the basic differences between generating heat in situ and injecting heat after surface generation influence the cost in different ways. This study compares the cost of heating a reservoir either by steam injection or by forward combustion. There has been no consideration of recovery. Presumably, recovery from the swept region would be high in either case. The sole consideration was the cost of heating to the same radial distance by either process. PROCEDURE THE MODEL The basis for comparison was a mathematical model similar to that used by Chu' for combustion. The model simulates a radial heat wave in two-dimensional cylindricaI coordinates. It includes heat generation, conduction and convection within the reservoir and conduction in the bounding formations. Thus, heat losses from the formation are considered. Three significant modifications were made. 1. Equal logarithmic increments rather than equal increments were used for the mesh spacing in the r direction. By this technique large distances were simulated with relatively few mesh spaces. 2. A backward difference approximation to the convection term was used to avoid troublesome oscillations which result from a central difference approximation when the convection term is large. 3. The radial increments of the combustion zone motion were not necessarily uniquely related to the mesh configuration. The cumbersome step function introduced by the heat of vaporization of steam was circumvented by assuming the enthalpy of the steam to be a linear function of temperature between reservoir temperature and steam temperature. This is equivalent to assuming an average heat capacity numerically equal to the difference between the enthalpy of saturated steam and the enthalpy of water at reservoir temperature divided by the difference between the two temperatures. Heat losses obtained by this model are in essential agreement with those obtained by the analytical solution of Rubenshtein.' A detailed description of the model is presented in the Appendix. Using the model, the times required to heat to particular radial distances were obtained as a function of injection rate and other physical parameters. For the steam case, injected fluid was assumed to be saturated steam at pressures of either 500, 1,000 or 1,500 psia. The corresponding temperatures are 467, 544 and 596F, respectively. Thickness ranged from 10 to 50 ft and injection rate ranged from 100,000 to 1 million Ib/D. Reservoir and overburden temperatures at the injection well were assumed to be that of saturated steam at the injection pressure. The effect of maintaining the overburden temperature at the well at a different temperature (initial reservoir temperature) was examined with no significant change in behavior. The influence of wellbore heat losses for the steam case was determined in the following manner. The rates of heat loss as a function of time were estimated using an approach similar to that suggested by Ramey." he data were based on injection through 2%-in. tubing in 7-in. casing. Integration of these data over the entire iniection period yielded the total heat loss. Total heat losses were then corrected to their equivalents in steam (this number resulted from dividing the total heat loss by the latent heat). This was considered additional steam required to accomplish the reservoir heating and the total cost was increased accordingly.

Jan 1, 1967

By P. R. Thomas

The Bureau of Mines determined the costs associated with the production of chromium, in the form of chromite and high-carbon ferrochomium, from the demonstated resources of 10 market economy nations. The analyses evaluated the relative geologic and economic position of these chromite resources contained within 80 producing or potential mining operations. This report presents cost evaluations of a demonstrated resource of chromite, contained within the nations studied, of appoximately 1.2 billion metric tons (t). Of this total, 70 pct is contained within the southern African nations of Zimbabwe and the Republic of South Africa. The majority of current chromium mining and smelting capacity is contained within these two countries as well. India and the Philippines have recently demonstrated greatly increased chromite resources and hold the most promise for expanding both chomite and ferrochromium production outside southern Africa. Their demonstrated resources represent approximately 7 and 16 pet, respectively, of the cost evaluated total tonnage. Chromite resources, on an identified or hypothetical basis worldwide, are highly concentrated within Zimbabwe and South Africa, with these two nations containing in excess of 95 pet of the total. Given the present market structure, a majority of chromium contained within the demonstrated chromite resources of the nations studied is economically recoverable; but from a long-term resource and economic perspective, South Africa should inceasingly dominate the markets for both chromite and high-carbon ferrochromium. In addition, it is anticipated that an increasing percentage of chromium traded on the world market in the future will be in the form of high-carbon ferrochromium as opposed to chromite, as this additional processing stage continues to relocate from the industrial nations that account for a majority of chromium consumption to those nations that mine chromite.

Jan 1, 1984

By Eldon Keith Stanek

This annual report deals with four distinct tasks related to research on the safety and reliability of mine electrical power systems. Task one is to develop tests and the associated instrumentation to detect incipient faults on a mine or any low-voltage power system. Task two is a dual effort related to the digital prediction of electrical transients on mine power systems and laboratory testing of transient suppression devices. Task three is also a dual effort. This task consists of both theoretical and laboratory work to assess both the reliability and the fail-safe characteristics of several items of protective equipment used in mine power systems. Task four consists of an effort to use programmable calculators and/or computer terminals to check overcurrent protective device coordination.

Jan 1, 1976

By Ludwig Schmidt

This report, the second of a series, presents the results of laboratory corrosion studies which were made in connection with a one-year test on aluminum lease tanks conducted by the United States Bureau of Mines. Part I of the report contains the results of the field teats.5 The studies were made on an oil lease in a so-called "sour district," near Borger, Tag., where free hydrogen sulphide accompanied the production of oil, gas, and salt water. Steel tanks previously used on the lease had suffered severe corrosion, because steel is inherently susceptible to attack by hydrogen sulphide. Because of the high resistivity of aluminum to the action of hydrogen sulphide, it Was believed that this metal had promising possibilities as a material for the construction of lease tanks in "sour districts." The results of the one-year field teat proved that aluminum lease tanks will withstand corrosion by hydrogen sulphide, but it was found that aluminum was susceptible to attack by salt water, which was invariably present in certain portions of the tanks, and that hydrogen sulphide accelerated this salt-water corrosion in an indirect manner, as will be explained hereinafter. In order to study corrosion conditions encountered in the tanks during the test period, a laboratory was maintained at the site of the aluminum lease tanks.

Jan 1, 1931

By R. H. Sprute

The Federal Bureau of Mines conducted full-scale field tests in electro-kinetic dewatering and consolidation of slimes in cooperation with the Hecla Mining Co. at two of the firm's underground mines in north Idaho. To test the technique on new deposits, 4,000 ft3 of slimes from a collection sump, pumped into a watertight stope equipped with electrodes, were treated in two steps. Immediately after placement, direct current was applied using a floating electrode to hasten settlement of suspended fine particles. After removal of clarified water, the residue was further dewatered and hardened with electrokinetic treatment. In 25 hours, the material had become firm and dense with a surface capable of supporting workmen. In testing old deposits, 10,000 ft3 of slimes, placed in an unused tail drift 10 to 12 months previously, were treated. This material was sufficiently consolidated by electrokinetics to allow its removal from the mine with standard ore-handling equipment. In both tests, electrokinetic treatment densified slimes in a relatively short time with moderate power consumption.

Jan 1, 1976

By T. Joseph, E. Zheng, M. Curley

"Hydraulic transportation efficiency and production optimization are considerations in the surface extraction of Athabasca oil sand deposits. To reduce the dependence on haul trucks, it is possible to extend the hydraulic transport system to production faces using a mobile at-face slurry system (AFSS). The flexible arrangement of connected pipelines transports slurried minerals from the mining face to the processing plant. An experimentally verified mathematical model indicates the friction loss of oil sand slurry associated with the AFSS. Laboratory-scale testing enables extended analyses for examining pipeline slurry transport in an oil sands environment.RÉSUMÉ L’optimisation de l’efficacité du transport hydraulique et de la production sont des considérations importantes dans le domaine de l’exploitation à ciel ouvert des gisements de sables bitumineux de l’Athabasca. Afin de réduire la dépendance envers les camions de transport, on envisage d’étendre le système de transport hydraulique aux fronts de taille à l’aide d’un système mobile de transport des matériaux sous forme de boue à partir du front de taille (AFSS, de l’anglais at-face slurry system). L’organisation flexible des conduites reliées permet le transport de minéraux à l’état de boue du front d’exploitation jusqu’à l’usine de traitement. Un modèle mathématique vérifié de manière expérimentale indique la perte de charge par frottement des schlamms provenant du traitement des sables bitumineux associée à l’utilisation de l’AFSS. Des essais en laboratoire permettent de mener des analyses approfondies portant sur le transport de boues dans des conduites dans un environnement de sables bitumineux. INTRODUCTIONObjectives and scope of studyThe at-face slurry system (AFSS) concept has become a competitive means for materials handling to optimize haulage system efficiency and cost. The mobile and flexible arrangement of the AFSS introduces a unique set of hydraulic transport problems. This paper will focus on developing the mathematical models governing the friction and head losses within the AFSS concept.Background of the problemLarge-capacity shovels and dump trucks are increasingly used for excavation, loading, and hauling in the operation of surface mining. Production cost and efficiency optimization are demanded during the Athabasca oil sands (Alberta, Canada) mining process to secure North America’s energy supply. Increasing haulage distances, rugged terrain, and a constrained mine environment are conditions that will reduce the effectiveness of the shovel-truck haulage system (Frimpong, Szymanski, & Changirwa, 2003). In such conditions, the tire heat index and weight, distance, and time limits for truck haulage can be exceeded, simultaneously creating extreme tire wear and high maintenance costs. In addition to low production cost and equipment effectiveness, a mining environment also requires efficient waste-material recycling and distribution. Waste materials need to be recycled from the processing plant to a new destination such as a tailings dam, or replaced in mined-out areas such as backfill. The Athabasca oil sands configuration and location characteristics result in a mining environment that would benefit from flexible pipelines for constant production and an efficient waste-material recycling process."

Jan 1, 2017

By A. K. Watt

"The availability of fresh water to meet present and future needs in Ontario is of concern to an increasing number of people. Rain and snow are the source of our potable water and provide, on the average, some 180,-000 billion gallons of water annually. This amount is reduced to 94 billion gallons a day as a result of the evaporation and transpiration of water and our inability to construct the necessary reservoirs for capturing surplus stream flow.The water used for domestic, irrigation, public supply and industrial purposes amounts to some 7 billion gallons daily at present and will reach 21 billion gallons daily by the year 2000; however, only about one-fifth of the water used is actually consumed, and this, along with the possibilities of water re-use, improves the water supply picture still further.The need for adequate pollution control has accompanied industrial and urban expansion and is an important factor in the extent to which our surplus water is used. In the 10-year period since the formation of the Ontario Water Resources Commission, the cost of water and sewage works constructed in the Province has exceeded one billion dollars. A special effort is now being made to control the industrial pollution situation.Numerous federal and provincial agencies are engaged in hydrologie studies in the Province, providing in-formation of benefit to those involved with water resources management."

Jan 1, 1967

By AIME AIME

ON Thursday a most interesting symposium on "Gases in Metals" was held, with both morning and afternoon sessions. The morning was devoted principally to the considerations of the steel maker, the nonferrous field being taken up in the afternoon period. Dr. John Johnston, as chairman, introduced the subject with "A Short Analysis of the Gas-metal Problem and Its Practical Importance." He then introduced P. H. Brace who explained in considerable detail the various vacuum fusion and other methods in use at present, both here and abroad, in the study of "gases" in metals. He was fol¬lowed immediately by H. W. Graham on "The Effect of Oxygen in Steel." The papers elicited considerable discussion, the point being particularly noted by both Dr. Rawdon and Dr. Sauveur that a knowledge of "total oxygen" alone is not sufficient information for the metallurgist, distribution of oxygen being probably the more important. Dr. Johnston, in commenting on the lack of agreement among many of the methods now in use, such as the Ledebur and vacuum fusion, spoke of the contemplated plan of the Iron and Steel Division to have a number of standard samples analyzed by many laboratories by the various methods, the Bureau of Standards acting as a clearing house, so that more definite information may be obtained on the comparative accuracy of the method.

Jan 1, 1933

"Liberation is a key requirement for efficient separation in mineral processing. As a consequence of this an understanding of the inherent textural features of an ore is no longer possible since during the process of liberation, texture is destroyed. Knowledge of key textural features, such as mineral grain size and distribution, prior to breakage processes provides the opportunity to understand the textural drivers for ore hardness. Modern characterisation methods, including automated SEM-based techniques, provide the possibility of measuring mineral characteristics at a range of scales. This paper discusses how textural features of two different ore types in a porphyry copper deposit can be measured and interpreted at a number of scales. Standard breakage tests conducted on the ores indicate that one of the ores can be characterised as hard and the other as soft. The impact of mineral grain size and the presence and scale of vein type structures in the two ores have been used to determine the extent to which these features influence ore hardness.INTRODUCTIONIn order to effectively convert ore into metal, knowledge of both the processing stages and the characteristics of the ore are essential. Prior to the advent of technologies that enabled the fundamental understanding of the sub-process at each stage of processing and the measurement of appropriate ore properties the most effective way to understand how an ore would respond to a process was to put it through that process, for example the way to determine how an ore would break was to first break it. Existing comminution models seek to predict the size distribution of rock fragments as the result of applied energy based on knowledge of the rock strength. It is common for these models to consider the rock as homogeneous and despite providing important data for the design and optimisation of industrial comminution circuits these models are only applicable within a narrow range of operation. In order for reliable predictive models to be developed that account for the inherent ore characteristics, a step change is required in the type of measurements that are carried out to characterise an ore and the type of data that is extracted and used as model inputs."

Jan 1, 2016

By Bernard Lewis

This report summarizes the fundamental research and technical studies conducted by the Explosives Branch of the Bureau of Mines from July 1, 1943, to June 30, 1949. It is the thirteenth of a series of annual reports, which have aimed to bring to the reader a resume of the research results that have appeared in published form during each fiscal year. The work of the Explosives Branch covers a number of activities - explosives research, explosives testing, flame and combustion research, flammability of gases and vapors, dust-explosions research, and technical studies in the experimental mine. An important part of the work of the branch is fundamental research to advance our knowledge and understanding of explosion processes. Considerable emphasis has been placed on studies of ignition and flame stabilization, as it is felt that an understanding of these processes should assist materially in alleviating explosion hazards in coal mines. The results are also finding important application in the development of jet propulsion. Studies of the explosibility of gases, vapors, and dusts saving thousands of lives and are preventing the destruction of much property. In innumerable instances in which potential explosion hazards exist, safe operating procedures have been recommended from data taken in the Laboratory. Aware of the value to national security of research results of combustion, flame, and explosion, the Army, Navy, and Air Forces are actively supporting important phases of this fundamental research.

Jan 1, 1950

By ALEXANDER S. CORSUN

THE main orebody in the Hecla mine, Burke, Ida- ho, occurs along a nearly vertical shear zone in the Burke quartzite, with a substantial gouge and lamprophyre dike occurring in an irregular manner throughout the lode. The veins range from 3 to 40 ft. wide and dip from 70 deg. to 90 deg. There is 110 definite line of demarcation between the lode and the wall rock. Stringers of ore are often found in the wall rock for irregular distances. Horizontal but irregular quartz stringers are also found running into the walls and positions of the wall have a tendency to break to the quartz stringers and the accompanying gouge, which causes indefinite, uneven and extremely heavy side and top pressures.

Jan 1, 1930

By Shangyong Lin, Wei Sun, Weiping Liu, Muhammad Azam, Junfeng Cheng, Yujie Zhao, David Asubonteng, Michael Ngoie

Copper concentrates have wide application in global smelting operations, comprising primarily of chalcopyrite (CuFeS2) as the principal mineral, accompanied by chalcocite (Cu2S) and bornite (Cu5FeS4) as secondary copper-bearing minerals. However, these concentrates frequently harbor detrimental impurities, notably fluorine ions, which can cause various complications during the smelting process. Moreover, an elevated fluorine content in copper concentrates may entail financial penalties and sales constraints. This review conducts a comprehensive analysis of existing methods for the removal of fluorine, presenting a nuanced assessment of their merits and demerits. It also provides valuable insights into the current landscape of fluorine elimination from copper concentrates and pinpoints pivotal areas warranting future investigation. This review endeavors to serve as a pragmatic resource for researchers and industry professionals operating within this domain.

Jan 1, 2024

By Christopher Robben, Alexander Mosser

"X-ray transmission (XRT) sorting has been introduced into the minerals industry in 2006 and has found various applications in diamonds, industrial minerals and metal ore processing since. The technology offers planar projections of the atomic density of single particles similar to the principle known from airport scanners, but being capable of treating up to 150tph per metre working width. In 2010, a pilot operation using a belt-type sensor-based sorter went into production at the Mittersill mine to treat the fraction 16-28mm. After an optimisation phase, the results were superseding expectations and therefore in 2012 a bigger production plant was set up. Two XRT-based sorters are parallel in operation since. One is treating the fine fraction 16-30mm while the other one is treating the coarser fraction 30-60mm after the secondary crushing stage. The XRT sorters are operated with the objective to reject barren waste before it enters the mill and flotation plant. 105,000tpa of waste material are rejected per year and can be sold as aggregate for road construction. This means that about 22% of the run-of-mine ore are rejected at an early stage with a waste reject grade lower than 0.03wt%WO3. The installation has not only led to lower specific operating costs but also led to reduced tailings disposal in an environmentally sensitive area. This allows the mine to reduce its headgrade which allows for a longer mine life. Alternatively it is possible to produce more tungsten concentrate, which is delivered to the smelter. This article will introduce the technological principle of XRT-based sorting and will discuss the flow-sheet of the Mittersill mine. Experiences that have led to the current plant design are described as well as the impact it has on the operation."

Jan 1, 2014

By Francis J. Dennis

(San Francisco Meeting, October, 1911.) MANY factors govern the value of dredging-ground, and much capital can be wasted by the mistaken policy of contracting for the purchase of property and the installation of machinery before a thorough, examination has been made. To the uninitiated investor the presence of gold is generally the criterion,, and very superficial evidence is necessary to satisfy him as to this point. He considers the comprehensive report of a competent engineer as a wasteful extravagance and cannot understand why the engineer requires so much time and money to ascertain the information on which to base his conclusions, when the promoter can furnish him such pleasing and satisfactory data with but little expenditure of time and money. The uninitiated investor will often optimistically risk capital for purchase and equipment, and not until the venture comes to grief does he learn that the conditions are wholly unsuited for dredging. In many instances, a short preliminary examination by a competent engineer would have disclosed these facts. The mere presence of gold is by no means sufficient; some of the other factors necessary to be ascertained in determining the value of placer-ground for dredging-purposes are : (1) character and distribution of gold, and how much can economically be recovered; (2) character of bedding underlying the gravel, its contour, and whether its gold can be recovered by ordinary dredging-operations; (3) area and depths of gravel, surface contour, over-burden, water-level, proportion of fine material and boulders, and the presence of any material which might interfere with the dredging-operations and the recovery of the gold; (4) water-supply, power available, labor, transportation, and supplies, and cost of these ; (5) climatic condi-tions; (6) title to property, cost and royalties, and legal obstacles to carrying on dredging-operations. A brief reconnaissance may be sufficient to determine that some of the essential conditions for successful dredging are

Apr 1, 1912

A microcomputer based expert system is presented for fast and cheap mineral identification. Because of the increasing pipularityof and interest for minerals and precious stones (selling, hobby polishing, collecting, teaching etc.) we pointedly deal with gemstone identification. In most cases only some fundamental data are needed to identify a mineral sample (or precious stone) if we know how to use these data. The important, characterizing data of the well-known minerals are stored in the data-base of our program-system. The visible and measured optical and physical properties of the sample are compared adequately with the stored data to get the result, the name of the examined mineral. The system works in a simple, friendly way - asking questions, understanding answers - so that no special computer knowledge is necessary to use it, only the answers should be typed in. The main advantage of the system is that only relatively simple and fast measure-ments are required. Based on these measurements a fast, reliable identification is processed on a cheap com-puter running a sophisticated program-system. The MINTEST system handles even those cases when the tested mineral cannot be determined based on the given input data.

Jan 1, 1985

By R. Lasmanis, W. C. Utterback

"The Mount Tolman porphyry Mo-Cu deposit is 64 km south of Republic, Ferry County, Washington. It occurs in the composite Keller Butte pluton, which consists of the Keller Butte porphyritic biotite granite and granodiorite, the Mount Tolman quartz porphyry granite, and the Meadow Creek biotite granite phases. The three phases range in age from 61.3 Ma ± 2.3 Ma to 55.7 Ma ±2.0 Ma. The stockwork deposit occurs in the Keller Butte phase above the contact with the Mount Tolman quartz porphyry granite.Mount Tolman is a hybrid calc-alkaline deposit that has features of both a Climax-type and a plutonic type. Prior to post-ore faulting, the deposit had a flattened hood like shape. In plan it is elongated- 1.6 km wide, 3.2 km long, and up to 609 m thick. The orebody has a 292 o strike. It contains a geologic reserve exceeding 2.18 billion tonnes of ore averaging 0.093% MoS2 and 0.09o/o Cu using a 0.048% MoS2 cutoff. Of this total, 816 million tonnes of measured and indicated ore averaging 0.097% MoS2 and 0.09o/o Cu could be mined by open pit with an overall waste-to-ore ratio of 0.91 to 1.The deposit is a stockwork of quartz and quartz-sericite-pyrite veins and fracture fillings that contain molybdenite, chalcopyrite, sphalerite, and magnetite. Five separate episodes of fracturing and mineralization produced the orebody and were followed by four additional episodes of fracturing with sulrgrade mineralization. The Mount Tolman deposit contains propylitic, argillic, phyllic, topaz greisen, and potassic alteration zones. Extensive silicification overlaps the K-feldspathized, quartz-topaz, and phyllic alteration zones."

Jan 1, 1995

By Albert W. Deurbrouck

This report describes the preparation characteristics of the significant coalbeds in Russell County , Va . Almost 2 million tons of coal was mined in 1961 ; 75 percent of the coal was cleaned mechanically in preparation plants in the county . The coal of Russell County is ranked as medium- to high- volatile bituminous , contains small amounts of sulfur , and generally requires some cleaning to reduce the ash content to limits acceptable for metallurgical purposes .

Jan 1, 1963

By Krishna Parameswaran

This paper discusses sustainability considerations in primary copper smelting using selected examples of practices at ASARCO LLC, an integrated U.S. primary copper producer. Using the classic Brundtland Commission definition of sustainable development, i.e., “development that meets the needs of the present without compromising the ability of future generations to meet their own needs,” the paper discusses how copper mining and smelting practices can be made sustainable. The examples used to illustrate sustainability considerations include: (1) adoption of flash smelting; (2) emission reduction and process improvement associated with anode refining of blister copper and the converter retrofit project, and (3) preliminary research findings on alkali treatment of copper smelting slags and copper mine tailings.

By J. M. Barker

New Mexico is the leading domestic producer of perlite, a hydrated volcanic glass that can be expanded thermally to form a white, very porous, lightweight material. The United States is the leading consumer and producer of perlite in the world (Pettifer 1981). New Mexico produced, at five mines (Fig. 1), about 86% of all domestic crude ore mined in 1984 (Meisinger, 1985). Perlite is mined in 6 other western states, ore is expanded in 33 states, and the expanded ore is consumed in all states (Meisinger, 1985). Gross value of domestic ore mined in 1984 was about $16,500,000 (FOB mine; Meisinger, 1985) with much value added by expansion and processing prior to sale to end users. In contrast to the ubiquitous nature of perlite products in the U.S. economy, facilities for testing perlite ore, expanded perlite, and perlite products are notably lacking on a commercial, cost-effective, or readily accessible basis. The New Mexico Bureau of Mines and Min¬eral Resources (NMBM&MR) established a perlite¬testing facility in 1984 to mitigate this lack and to further the mining of perlite in the state.

Jan 1, 1985