Search Documents

By J. O. Jones

[Willis Mountain in southeastern Buckingham County is one of several kyanite deposits its central Virginia. It is composed principally of kyanite resulting from metamorphism of siliceous sedimentary beds rich in alumina. The mountain, which trends north-south, is 2 miles long and is topped by a narrow ridge with sleep rugged sides rising to an altitude of 1,160 feet and projecting 500 fast shove the surrounding countryside. Bureau Mines engineers examiner Willis Mountain early in 1949, when bonded concentrations of coarsely crystalline kyanite were observed in the kyanite-quartzite on the northern end of the mountain and in loose boulders on the eastern slope. Commencing in late July 1949, the investigations continued on the Long Mountain segment for 11 months, ended in June 1950. A total of 600 samples from 32 diamond-drill holes, aggregating 3,876 feet of drilling, and from 255 feet of sampling in 3 trenches was assayed for kyanite and ferric oxide.]

Jan 1, 1954

By Bernard Porter

The rate of the heterogeneous reaction between high-purity uranium metal and uranium tetrafluoride in molten lithium fluoride was measured. The apparent heat of activation for the reaction is 16.91 kilocalories per mole of UF4. A surface-controlled mechanism is suggested in which UF4 is adsorbed on the uranium metal surface. Additional UF4 reacts with the adsorbed species and the metal site to form an activated complex that decomposes to the product UF3. The reaction is an important source of metal loss in the electrowinning of uranium metal.

Jan 1, 1966

By Marko Oosthuizen, Charl P. Botha, Lidia Auret, Annelette Malan, Marthie de Leeuw

Flotation performance is affected by upstream disturbances (e.g., mineralogy, water quality, flow rate) and controlled variables (e.g., pulp level and air addition). Process disruptions can lead to undesired conditions, such as pulp overflowing flotation cells (with insignificant/absent froth, and thus no valuable mineral concentration). Early detection and appropriate intervention of pulping events improves concentrator performance. An approach to real time flotation pulping event detection by means of convolutional neural networks is presented, including a case study of the industrial application of this technology on three flotation banks.

Feb 22, 2026

By H Bateman, I Cawrse, G Carnes, S Cawrse

In developing mineral resources, the focus typically centres on the management of identified social and environmental impacts and compliance with regulatory requirements. However, opportunities to protect and enhance the environment and communities are most effective in the planning and design phases. Achieving the objective of integrating sustainability considerations as an element of design decision making requires that the design criteria be technically sound, relevant to the project and applicable to desired design outcomes. This is particularly important for projects employing virtual teaming, where design engineers may be geographically dispersed and are unlikely to be familiar with site specific sustainability challenges and opportunities. This paper documents the approach taken by BHP Billiton to incorporate sustainability principles, objectives and guidelines in design criteria for the Olympic Dam Expansion (ODX) project. It describes the range of inputs used in defining sustainability objectives which interface in a framework that is dynamic and transferable to other mining projects and to engineering design in general. The Sustainability in Design Criteria document distils statutory requirements, corporate standards, lessons learned and leading industry practice into a single coherent framework that supports engineers to approach problem solving as a holistic and integrated exercise with a long term perspective. The framework also serves to improve linkages between internal stakeholders by fostering greater communication, collaboration and innovation to deliver more sustainable outcomes through the design process.

Jan 1, 2009

By E. M. Cameron

Reconnaissance radiometric and geochemical data have been obtained for an area on the western shore of Wollaston Lake that includes the Rabbit Lake uranium deposit. The study area is extensively drift cover ed. The geochemical data were obtained by analysis of center-lake sediments and surface waters for a variety of elements and other constituents. The airborne radiometric data comprise measurements of eU, eTh and K obtained with a .50,000-cc NaI (Tl) detector at a mean terrain clearance of 120 m and 5-km flight-line spacing. Uranium in lake sediments and uranium in waters are the most effective geochemical indicators of uranium mineralization; the other elements measured are not notably anomalous. A sample site density of one per 1 8 km 2 is more than adequate for identification of the mineralized area. Because many water samples contain close to or below the current analytical detection limit of 0.05 ppb U, the use of sediments is generally favoured. for broad-scale reconnaissance in the region. Uranium in these lake sediments appears to be little influenced by variations in the organic or iron and manganese content. The most effective radiometric indicator of the mineralization is the eU/eTh ratio. This parameter is less influenced by environmental variation on the ground beneath the flight line than eU alone . The eTh/K ratio is anomalous under the Athabasca Formation unconformity where, in places, the uranium mineralization is localized.

Jan 1, 1977

By B. A. Slaker, T. Miller

"An underground limestone mine in eastern Ohio was experiencing significant floor heave and roof falls, attributed to high horizontal stresses. Areas of the mine showing floor heave were monitored with roof-to-floor extensometers and photogrammetry surveys, to determine the rate and magnitude of heave. Extensometer data were recorded hourly at four locations across adjacent entries while photogrammetry surveys of the floor were performed at the same locations every two to five weeks. A final survey was performed using an I-Site 8200 laser scanner. Following instrumentation, floor heave up to 10.1 cm (4 in) was measured by the extensometers, photogrammetric reconstructions, and laser scanner over a 6-month period. The extensometers were biased by the location where they were placed, failing to consistently capture the location and extent of floor heave and cracking. The photogrammetry surveys were not precise enough to capture small magnitude movements. Mining in the area was halted and within several months the floor movement and incidence of roof falls was significantly lessened. INTRODUCTION Limestone formations in the United States can be subject to relatively high horizontal stresses due to the presence of tectonic loading of the strata. Horizontal stresses have a documented history of causing stability issues in underground limestone mines. Kuhnhein and Ramer (2004) discussed the influence of horizontal stress on complex ground control interactions associated with limestone pillar design and mine layouts. Esterhuizen et al. (2008) documented roof damage observations associated with high horizontal stresses such has roof guttering, beam instability, oval-shaped falls, and failure propagations. There have also been a number of documented case histories of horizontal stress causing unexpected roof and pillar failures at shallow depths (Stacey and Yathavan, 2003). To the knowledge of the authors, there has only been one well-documented case of floor failure causing stability issues in an underground limestone mine. Murphy et al. (2015) documented the role that a weak, moisture-sensitive floor had in the development of a massive roof collapse. For this paper, the study site neighbored, and was in the same general geology of, the site in Murphy et al. (2015). However, the weak, moisture-sensitive floor was not present for the current study. The current study site has experienced significant floor instabilities caused by high horizontal stresses. The instability area was monitored using two different methods to determine if the floor failure would eventually propagate into roof or pillar failure. The objective of this paper is to analyze displacement monitoring measurements from string potentiometers and remote sensing techniques in an area experiencing active movement. Based on the measurement trends and observed damage from inside of the mine, the presumed failure process will be discussed."

Jan 1, 2017

By W. G. Pariseau

A study of coal pillar strength was done at the Beehive Mine during a three year period, 1974?1977, in a cooperative effort involving the University of Utah, RE/SPEC, Inc., and the American Coal Company (Pariseau et al, 1977). The Beehive Mine is located in the Wasatch Plateau coal field in central Utah near Orangeville, Utah, where mines are developed from outcrops between steep canyon walls with topographic relief of a kilometer or so (3,600 ft). Coal is found in Cretaceous sediments that dip gently to the west. Detailed geology of the Wasatch Plateau is described by Doelling (1972). Mining was done in the Blind Canyon seam. An earlier Deseret Mine worked the Hiawatha seam that is lower in the stratigraphic column by about 36 m (120 ft). Mining progress and ownership changes occurred in time with mine mergers and name changes eventually to the collective Des-Bee-Dove label. At the Beehive Mine, depth varied with topography but was approximately 360 m (1200 ft) on average; seam thickness varied from 1.5 to 6 m (5 to 20 ft) and usually required two passes of the miner. The mine was eventually closed and finally reclaimed in 2003. Semborski and Oakley (2006) present a brief history of the mine and describe the reclamation work in some detail. Figure 1 shows the surface topography in the vicinity of the mine that is in the center of the figure.

Feb 23, 2014

By R Ayothiraman

Tunnel excavation may induce adverse effects on nearby existing structures/foundations in urban areas. Accurate prediction of tunnelling effects on pile foundations of nearby structures in the urban environment poses a major challenge during design. Several studies have been undertaken to understand the mechanisms of the soil-tunnel-pile interaction, which focused only on influence of tunnelling on nearby existing building and foundations. However, effect of pile loading on existing tunnels did not receive enough research attention so far. So it is essential to measure the response of existing tunnel-lining due to loading on newly constructed pile to assess to the safety against the additional forces/moment caused by pile loading and to evaluate the critical distance for the proposed construction of any structures from the tunnel location. This paper presents result of three-dimensional (3D) finite element analysis carried out in ABAQUS to investigate the effects of pile loading on existing tunnels embedded in cohesive soil. It is found that the effects on tunnel lining depend on horizontal separation distance between pile and tunnel as well as location/elevation of pile tip with respect to tunnel location.

Mar 8, 2011

By Richard M. Winar

In September of 1988, the United States Environmental Protection Agency (US EPA) published final regulations that effect owners and operators of underground storage tanks (USTs). These regulation include stringent technical requirements for owners and operators of USTs containing petroleum and certain hazardous substances. The technical requirements effect both new (those installed after December 1988) and existing USTs and include notification; performance and operating standards; release detection, reporting, investigation; release response and corrective action; and closure requirements for out-of-service USTs. The USEPA also published final regulations regarding financial responsibility requirements for owners or operators of petroleum USTs in October of 1988. These regulations require owners or operators of petroleum USTs to demonstrate financial responsibility for the costs of corrective action and compensating third parties for bodily injury or property damage caused by releases from petroleum USTs. Like thousands of other industries, the mining industry must become thoroughly familiar with these new regulations in order to properly manage their UST systems, ensure compliance, and understand other ramifications imposed by these regulations.

Jan 1, 1990

By J Foster

The Lanfranchi Nickel mine is located approximately 48 km south of Kambalda in Western Australia. Mining first commenced in the mid-1970s under the previous owner, Western Mining Corporation Ltd. After two years on care and maintenance, Panoramic Resources (previously known as Sally Malay Mining Ltd) purchased the operation in November 2004. The site currently produces approximately 10?000 tonnes of nickel metal annually from approximately 430?000 tonnes of ore. The Ore is mined from four main orebodies; Deacon, Helmut South, Lanfranchi and Schmitz. The Helmut South orebody is situated approximately 790 m below surface and extends to a resource depth of 940 m. Horizontal thickness of the orebody ranges from 10 m to 45 m in width, with the average being 30 m. Previous mining at the Lanfranchi operations specifically the Helmut orebody, had a history of seismic activity. When Panoramic Resources acquired the operation it was decided that seismicity was going to be an issue and therefore a mining method needed to be selected that could effectively manage this potential risk. The dip of the orebody is quite shallow at 45º, with a 30º plunge to the south . The hanging-wall comprises of very weak ultramafics. Due to these factors the orebody posed several mining challenges. To safely and effectively mine the Helmut South orebody in the Lanfranchi Nickel mine, underhand cut and fill mining was selected as the most appropriate mining method. Paste fill comprising of cemented gold tailings was the backfill of choice. This paper is intended to convey some of the key learnings from the use of a mining method that has not been commonly practiced in Australia.

Mar 21, 2011

By Diego Benites

El presente texto señala los resultados de la caracterización mineralógica de 28 muestras con importante contenido en sulfosales de plomo y cobre de origen hidrotermal provenientes de la Sierra Central del Perú. El principal objetivo fue caracterizar la mineralogía de la zona con énfasis en las sulfosales y el aporte de plata que éstas podían contener. Así, las sulfosales identificadas por microscopia óptica en conjunto con microscopia electrónica de barrido son: tetraedrita, tennantita, boulangerita, bournonita, fizélyita, jamesonita, semseyita, zinkenita; entre otros. Para determinar qué minerales aportaban plata y en qué porcentaje, se realizaron estudios puntuales por microscopia electrónica. Así también se verificó que la plata se aprecia en pequeñas cantidades en sulfosales de plomo, mientras que éstas aparecen en mayor abundancia con respecto a las sulfosales de plata y de cobre.

Oct 21, 2015

By A P. Wilkinson

This paper reports on the implementation of the critical control concept to manage material risks in the mining and metals industries. The critical control management (CCM) approach assumes it is better to identify weaknesses in risk controls before an incident happens as opposed to discovering weaknesses from an investigation after an incident occurs. The first is sometimes referred to as active monitoring and the second as reactive monitoring (Health and Safety Executive and Chemical Industries Association, 2006). Both are needed. However, whilst methods for both active and reactive monitoring of risk controls are well established in many high hazard industries, such as oil and gas, petroleum and chemical industries, until the publication in 2015 of the International Council on Mining and Metals (ICMM) guides, (Good Practice Guide and the subsequent Implementation Guide) (ICMM, 2015), there was no specific mining and metals industry guidance on critical control management. This paper reports on progress in implementing the ICMM guidance drawing on two main sources. First, a benchmarking survey of a representative sample of coal and metalliferous mines, both underground and open cut/pit), sponsored jointly by the Queensland Resources Council and the Queensland Commissioner for Resources Safety and Health in the context of a recommendation that the Queensland mining industry adopts high reliability organisation (HRO) principals (Queensland Resources Council and Commissioner for Resources Safety and Health, 2022). Second, it draws on Noetic’s experience of implementing critical control management in mining and other high hazard industries in Australia, Africa, China and North America (Wilkinson, 2018). The paper describes good practices found and where significant improvements can be made, providing specific and actionable examples of both. From this it also identifies how future guidance on this topic could be improved.

Apr 16, 2024

By R. V. Higgins

This report presents the results of a study of gas injection in the Upper and Lower Terminal zones in fault block VB and in the Upper Terminal zone in fault block VI, Wilmington field, California. This report is based on data obtained to January 1956. Earlier studies of gas injection in other California fields have been reported .3/ The Upper and Lower Terminal zones, fault block VB, have been producing oil since 1945 and the Upper Terminal zone, fault block VI, since 1948. Before starting the gas-injection project, the expansion of dissolved gas was the principal mechanism moving the oil to the wells. Gravity drainage and an edgewater drive also have contributed to the movement of the oil to the wells. When the gas injection was begun, the reservoir pressure and the oil production had declined appreciably. Gas injection was started in the Upper and Lower Terminal zones, fault block VB, in May 1953 and in the Upper Terminal zone, fault block VI, in October 1953.

Jan 1, 1957

By K. Narayana Swamy

Experimental results of 3-phase mixing in a physical model of a CCRL for metals refining, at high levels of bottom gas injection (up to a superfIcial gas velocity (Us) of 12.5 cm/min), are presented. A thermal tracer technique was used to elucidate both longitudinal mixing and interphase heat transfer. The results indicate that even under conditions of significant bottom gas injection, it should be possible to maintain acceptably low longitudinal mixing (D. < 20 cm2/s and D/uL < 0.1) in the CCRL. Interphase mass-transfer coefficients of the order of 0.02 cm/s and higher, are predicted from the measured interphase heat transfer coefficients using the mass and heat transfer analogy. Adequate performance is likely to be possible for an industrial CCRL, based on extrapolation of these results to full-scale conditions.

Jan 1, 1996

By Robert Essler, Paul Marsden, Paul Pandrea

"1. THE VICTORIA STATION TRANSPORT HUB Victoria Underground station is part of the Victoria transport hub, which comprises one of London’s main train termini and a major bus station. At the Underground station, the District Line running in the older shallow brick tunnels dating back to 1868 cross the Victoria Line running in the lower tunnels, which were opened in 1969. After Waterloo, Oxford Circus and King’s Cross/St. Pancras Tube stations, Victoria is the most frequented station on the London Underground network and is used by over 80 million passengers per year. Capacity at Victoria Tube station has been inadequate for many years with passenger numbers steadily rising. Overcrowding is a constant challenge and the station has to be closed regularly during morning and evening peaks until sufficient trains pass through to clear the platforms. For this reason an extension has been debated since the 1990s. After intensive preliminary investigations and feasibility studies covering many variants, which included a large-scale jet grouting test to determine the applicability of this technology as a protective measure for the tunnelling works, the project was officially started with the Victoria Station Transport and Works Act Order (Secretary of State, 2009) effective on the 18th of September 2009. Following a competitive tender process a joint venture of Taylor Woodrow and BAM Nuttall were awarded the contract by London Underground, with their design being carried out by Mott MacDonald Ltd. Ensuring the busy station remained open to the public was a key requirement of the Victoria Station Upgrade. Jet grouting works, which were executed from ground surface, were also carried out while the station was fully operational 2. OVERVIEW The Victoria Station Upgrade aims to increase the capacity of the Underground station significantly and one of its major design objectives is to optimise the transfer between the Underground lines. In order to achieve this, the following new structures are currently under construction: •,A new North Ticket Hall •,Extension of the existing South Ticket Hall •,Nine new escalators •,Connecting tunnels between the North and the South Ticket Hall •,8 new lifts providing step free access to all platforms •,An improved connection between the rail/bus terminus and the Underground station As the elevation and geometry of the existing structures cannot be changed, the new structures need to be adapted to the existing structures (see Figure 1)."

Jan 1, 2016

By M Simanjuntak, A M. Supomo

PT Freeport IndonesiaÆs copper/gold operation disposes of approximately 222 000 dry metric tonnes of tailings per day via two thickeners. Reduction of the flocculant dosage rates in each of the tailing thickeners has been achieved with the installation of Clarometers«, modifications to the existing operating DCS control strategy and a change in plant flocculant. This has reduced the flocculant consumption rate in the last twelve months by approximately 20 per cent. It has also highlighted the disparity in the settling rates of the two thickeners. Collaborative efforts between Cytec technical site engineers and Freeport operational personnel have made possible the overall gains achieved in the tailings thickener optimisation.

Jan 1, 2003

By R. B. Krog

The use of belt air as an intake source at longwall operations has greatly changed over the past decades. The practical considerations for the use of belt air are controlled by a variety of factors including airflow quantity and velocity, coal methane content, methane desorption rates, coal mining rate, belt length, stopping leakage, and the number of gateroad entries. At longwall operations, the advantages and disadvantages of belt air are different for gateroad development and longwall panel extraction. During gateroad development, the use of belt air to ventilate the working section will reduce the leakage from the intake to the belt compared to the belt air being ventilated outby the working sections because of lower pressure differentials. A greater quantity of airflow will reach the last open crosscut with belt on intake than outby, given the same amount of pressure and airflow available at the mouth of the section. This paper will investigate the current ventilation practices regarding the use of belt air during gateroad development and longwall panel extraction. Operating considerations regarding air quantities and pressures to deliver the required airflow will be investigated using ventilation network modeling.

Jan 1, 2009

By Sanjeev Malhotra

"This paper presents the results of a pile installation monitoring and performance assessment program for pile foundations supporting 14 piers and 2 abutments of the 1700-ft long bridge crossing over a river in Baltimore, Maryland. Dynamic measurements were conducted during installation and restrike of 16 test piles, one at each support location. The foundation piles were 30-inch diameter, 0.75 inch thick pipe piles at the piers and 24-inch diameter, 0.5 inch thick at the abutments. The piles at the piers were approximately 100 ft long and were designed to carry 260 kips service load with a factor of safety of 2.25. The piles were driven open ended into a variable site stratigraphy containing recent deposits of organic clayey silts near the mudline followed by loose to medium dense sand, with some silt, and then by soil deposits from the Cretaceous period consisting primarily of dense to very dense, poorly to well graded sands and gravels and cobbles, with occasional seams of very hard to very stiff, low to moderate plasticity silts and clays. This paper presents the approach taken to evaluate the driven index piles and to develop criteria for driving production piles. It provides the Engineer with some data on pile driveability in Cretaceous soils in the Baltimore area, soil set-up effect, and an estimate of pile capacity.INTRODUCTIONThe typical approach to pile foundation design and construction should include an indicator pile program with dynamic measurements and a static load test program. However very often paucity of funds and schedule constraints cause an owner to do away with conventional static load testing which can take $25,000 to $100,000 and several weeks per test. This paper examines an alternate (though not equivalent) truncated approach to foundation assessment and presents a case history where this approach was implemented.Dynamic measurements were conducted during pile installation for the 14 piers and 2 abutments of the new 1700-ft long bridge over a river in Baltimore, Maryland. Strain transducers and accelerometers were attached to the pile top during initial driving and restrike of 16 pipe piles. The foundation piles consisted of 30-inch outside diameter, 0.75-inch thick pipe piles at the piers and 24-inch outside diameter, 0.5 inch thick at the abutments. The piles were driven open ended into a variable site stratigraphy. The approach taken to assess the foundation performance included 1) a pre-field wave equation driveability analyses, 2) field pile driving measurements, 3) post-field Case Pile Wave Equation Analyses (CAPWAP), and, 4) revised wave equation analyses based on field and CAPWAP data. The following sections describe in greater detail each of the steps taken to assess foundation performance and the results obtained."

Jan 1, 2005

By Bernard F. Anderson

INTRODUCTION In this chapter, the term "down-the-hole drill" (DTH drill) is used as a generic name that encompasses the various trade names and other references such as "downhole drill," "in-the-hole drill," etc. This chapter is limited to a description of DTH drills used in stoping large underground ore bodies. DTH drills differ from conventional drills by virtue of the placement of the drill in the drill string. The DTH drill follows immediately behind the bit into the hole, rather than remaining on the feed as with ordinary drifters. Thus, no energy is dissipated through the steel or couplings, and the penetration rate is nearly constant, regardless of the depth of the hole. Since the drill must operate on compressed air and tolerates only small amounts of water, cuttings are flushed either by air with water-mist injection or by standard mine air with a dust collector at the collar. HISTORICAL DEVELOPMENT Mine managers have long known the economies enjoyed by quarry and open-pit operators in producing large quantities of ore. The savings are due primarily to the availability of massive equipment, capable of drilling large blastholes to reduce the amount of drilling, increase the fragmentation, reduce secondary blasting, and im¬prove the flow of the product. In an attempt to reduce underground mining costs, various methods are used for long-hole drilling, includ¬ing standard pneumatic percussion drifters and diamond drills. These systems have their shortcomings; percus¬sion drills are limited to small hole sizes and they ex¬perience excessive deviation and significant loss of energy with increased depth. The diamond drills provide deeper and straighter holes, but only at high cost. Both systems suffer from high noise levels, low penetration rates, and poor explosives distribution, among other problems. When the mining companies approached the drill manufacturers for a compact and portable large-hole jumbo for underground use, they specified not more than 1 % deviation on 60 m (200 ft) of vertical hole and a penetration rate of 15 m/h (50 fph). On Dec. 23, 1960, a test unit was placed in service in Montana and met the performance criteria. Though lacking the so¬phisticated features available today, the economies of surface blasting were brought underground. Unfortunately, the first system did not gain immedi¬ate acceptance in the industry. Among the factors con¬tributing to its demise were resistance to change, the need to alter development methods for the ore bodies, and a lack of flexibility in moving the rig from setup to setup and from level to level. In 1972, the mining industry again challenged the drill manufacturers to provide a workable jumbo that would combine compactness, ease of maintenance, relia¬bility, and efficiency, all on a self-propelled chassis. The manufacturers responded by providing improved jumbos, which have been accepted with enthusiasm throughout the mining industry. Today&apos;s DTH jumbos are capable of drilling from 100 to 200 mm (4 to 8 in.) diam holes that can be reamed to even larger diameters. The holes can be drilled to depths of 150 m (500 ft), depending upon ground conditions and the capability of the jumbo to retrieve the steel and drill. Fig. 1 illustrates a typical DTH jumbo. APPLICATIONS The uses to which DTH drill jumbos have been put are quite numerous, with new uses being found regularly. For convenience, these uses may be classified as primary blastholes and nonblasting holes. Primary Blastholes The original purpose for the development of the DTH jumbo was for drilling primary blastholes that could be mined by open-stope methods. Prior to the advent of the DTH jumbo, extensive development was required before production drilling could begin. Sub¬levels were required to allow access for column-and-arm stopers or ring/fan jumbos, to the extent necessary based on the effective penetration of the chosen machine. With the DTH jumbo, the mine engineer is able to reduce preproduction time and development costs. How¬ever, the most significant saving results from an im¬proved cost per ton of broken ore in the production phase. To utilize a DTH system, only a top heading and drawpoints are necessary. The top heading can be the width of the ore body with a 3.7-m (12-ft) back. A drop-raise pattern is drilled and shot to begin the stoping operation, providing a free face for subsequent blasting. A typical layout is illustrated in Fig. 2. The advantages of this system include: 1) Drilling and blasting are independent operations, and blasting can be performed at a rate congruous with the mine&apos;s ton-per-day capacity. 2) The development layout is simplified. 3) Good explosive distribution is achieved, provid¬ing more uniform fragmentation. 4) Environmental conditions for operators are im¬proved, including improved safety with all work directed downward (not overhead), lower noise levels, little fog, and a reduced dust count. 5) Improved production per manshift. 6) Simplified and easier operator work cycles. 7) Reduced cost per ton of product. 8) Fewer holes lost due to ground shifts. Nonblasting Holes With the introduction of the compact DTH jumbos, other practical uses became apparent, including the drilling of: 1) Holes for sand fill, from level to level and from level to stope. 2) Drain and dewatering holes. 3) Power and communications cable holes.

Jan 1, 1982

By R. V. Ramani, J. M. Mutmansky, P. C. Luna, V. A. Marple, Honglin He, B. A. Olson

The development of a sampling instrument for the assessment of an underground coal miner’s exposure to airborne respirable coal mine dust on a continuous and real-time basis has been long identified as essential for timely initiation of control actions. A respirable dust dosimeter (RDD) which operates on the principle of increasing pressure across a filter media with increasing dust mass on the filter has been developed by the National Institute for Occupational Safety and Health. Comparisons of the performance of the RDD with an U.S. approved gravimetric respirable dust sampler (GRD) have shown that the RDD may meet the requirements for measuring miners’ exposures on a cumulative, near real-time basis such as mid-shift and end of shift exposures. Recently, the performances of the RDD and GRD were compared by conducting side-by-side area sampling experiments in a controlled experimental environment in the laboratory and in underground coal mines under normal operating conditions. In this paper, the results from the in-mine study are presented and discussed. The experimental design for the in-mine study included two mines in different coal seams in different geographic coal regions. To ensure a wide range of concentrations, the experiments were conducted in a continuous miner section in Mine 1, and a longwall face in Mine 2. Airborne dust sampling was conducted for four different shifts at each mine. In each shift, two samples of different exposure durations were collected from two different locations. Each sample consisted of the readings of three dosimeters and the exposed filters from the three paired GRD samplers. As a result, a total of 96 comparative samples were obtained, 48 for each mine. The data were analyzed for the precision of the RDD and GRD measurements and for the relationships between the differential pressure of the RDD and the mass of dust on the paired GRD filter. The analyses indicate that, on the average, the RDD and the GRD track the airborne respirable dust concentrations well, exhibiting both a high correlation between the two measurements and a reliable predictive relationship of one from the other. Details of the experimental design, data analyses procedures, results, conclusions and recommendations of the underground experiments are presented in this paper.