Search Documents

By Frank A. Jerabek

Problems of mine backfilling and fill material deposited underground, the characteristics and relationship between the deposited fill material and overlying ground, and the practical applications and limitations of hydraulic backfilling as ground support are discussed. A great variety of materials ranging from coal washery refuse to concentrator tailings is used as hydraulic fill. Some materials will solidify and cement; others will resemble quicksand, Hydraulic fill as ground support is more efficient in inclined mine openings than in horizontal mine openings, where it cannot be placed tightly to the back. This and other deficiencies of hydraulic backfilling led to the development of pneumatic stowing. Research work in hydraulic backfilling at the Pennsylvania State University is also discussed. This research work includes the investigation of segregation in the discharged fill slurry, the quantity of solids escaping in the drain liquid, the relationship of escaping solids to slurry concentration and discharge rate, and the compressibility of fine fill material.

Jan 1, 1965

By Josef K. Alter

Long-term performance and behavior of post-tensioned ground anchors subjected to axial cyclic loading constitutes an important aspect of the stability, reliability and overall performance of wind turbine deep foundations. Axial cyclic loading of post-tensioned (PT) ground anchors in soils has not been thoroughly investigated as evidenced by the research conducted for this topic. This paper evaluates research test data, available literature, and industry expert opinion on the current status and problems of deep foundation post-tensioned ground anchor (PTGA) technology, as applicable to the wind energy industry. It also introduces a proposed design solution that addresses the problems of construction cost and long-term performance of wind turbine deep foundations in soils subjected to dynamic cyclic axial loading. Deep foundations using ground anchors for wind turbines have only recently gained attention as a possible viable alternative to the mass spread footings currently in use. One of the primary problems with general acceptance of current PTGA designs is the need for long-term anchor maintenance. The research that was conducted for this study indicates that current literature only partially addresses the many factors influencing load capacity and pullout performance of ground anchors. The lack of information indicates the deep foundation industry has fallen behind in designing and implementing new technology to improve safety and performance, ensure sustainability, reduce costs, and address environmental responsibility. This paper describes the significance of this problem as it applies to the wind energy market, and proposes a new technology solution. The research, expert opinion, and analysis presented by the author is used to support the premise that ground anchor construction cost and long-term maintenance can be reduced with PTGA systems using the Con-Tech Systems (CTS) patent-pending Groutable Void Form (GVF) technology.

Jan 1, 2010

By Simón Díaz-Quezada, HUMBERTO ESTAY

The heap leaching process has been widely used for recovering different metals since its first application at the end of the 1960s. In Chile, copper production via heap leaching has accounted for between 30 and 40% of annual copper production over the past 10 years. This level of production has been achieved through and supported by the use of a mathematical relation, known as the leaching ratio (LR) or irrigation ratio (IR), which relates operational parameters with metal extraction in a heap leaching operation. This ratio has been used to develop leaching column tests, to scale up results from the laboratory to industrial operations, to design new heap leaching plants, and in metallurgical control and production estimation. In spite of the widespread industrial use of this relation, few scientific studies mention it. This is due to its simplicity and basic theoretical foundations. This disparity between industrial practice and scientific research could lead to operational decisions which lack substantial theoretical support, and to scientific studies which have limited industrial impact. Against this background, several questions arise about the use of the LR: What are the constraints on the use of the LR? Are there practical advantages with respect to reported kinetic models? What is the main reason that industry prefers the use of the LR over kinetic models, which enjoy greater theoretical support? In order to guide its future use, this paper describes the leaching ratio and its current uses and limitations, through a literature review and case studies.

May 2, 2020

By K J ROSENGREN

Underground rock mechanics was initiated as a formal discipline in Australia by early studies for underground structures for the Snowy Mountains Scheme in the 1950s. These techniques were quickly embraced by underground mining and there has been steady development to the present time. The paper reviews the status of current techniques for rock mechanics studies and discusses some important issues such as ground support, mine filling and caving. It concludes that a considerable degree of engineering judgement is still required for the practical application of rock mechanics to underground mine design.

Jan 1, 1992

By S. F. Urban, G. Derge

At the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for ' large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions of operation. The most important general conclusion reached was that the time a heat is held under a reducing 'lag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. Procedure The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. companion slag and metal samples were taken just prior to slag-ofi and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional I3 heats. slag Sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from the furnace in a well-slagged car-bometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace hats. The Big wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting I in. wide, 1 1/2 in. long, and 34 in. maximum thickness, and was finally adopted as the most satisfactory design.

Jan 1, 1948

By S. F. Urban, G. Derge

At the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for ' large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions of operation. The most important general conclusion reached was that the time a heat is held under a reducing 'lag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. Procedure The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. companion slag and metal samples were taken just prior to slag-ofi and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional I3 heats. slag Sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from the furnace in a well-slagged car-bometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace hats. The Big wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting I in. wide, 1 1/2 in. long, and 34 in. maximum thickness, and was finally adopted as the most satisfactory design.

Jan 1, 1948

By Rhual L. Guerguerian

MINING has been practised by mankind for over sixty centuries (1). In 1876, the "ball mill" was patented, and during the century that followed rotary grinding developed to the state where individual machines are treating tens of thousands of tons of ore per day. This paper gives a brief description of design practices prior to the availability of advanced facilities, followed by modern analytical design development at Dominion over the past ten years.

Jan 1, 1978

By Robert Bissonette, Samir Sbai

Machine Situational Awareness (MSA) requires the ability to efficiently evaluate the probability of interaction of objects within the environment, without creating false alarms or ignoring materializing hazards. To do this, an MSA system needs to assign context to observed object activity and integrate as much information about object identity, kinematics, behavior, and current state as possible. This paper describes how known object characteristics, attributes, and activities (drilling, dumping, driving, etc.) can refine interaction probabilities and help identify rogue actors that introduce anomalous risks to the health and safety of miners. Path projections need to incorporate velocity and direction as a function of time while accounting for terrain, safety response, environmental factors, current assigned activity, etc. This paper also describes the methodology for properly prioritizing responses to place the highest value on human safety.

Feb 1, 2024

By Gerd Weyand

Gontermann-Peipers GmbH (GP) Germany developed a new, high alloyed steel grade for the manufacturing of back-up rolls. The advanced GP double pour casting processes provide highest flexibility in being quite open in rolls work layer chemistry and hence microstructure with no influence on core respectively neck properties. GP took the process advantage to provide a brand new back-up roll grade with remarkably reduced roll wear while operating with textured work rolls. In the meantime several successful trials have been made with this new roll grade on different Skin Pass Mills. As a result the performance of back-up roll and thus availability of mill will be improved while specific costs for mill will drop. This quite new back-up roll grade has recently been launched. As next step increasing the field of applications is under progress.

Aug 17, 2017

By A. F. Giamei, F. Landis, M. O. Duffy, R. J. Mador

"The directional solidification of complex advanced gas turbine airfoils must be carried out without the nucleation of undesirable grains and with minimal shrinkage. Such problems are typically eliminated by using a number of mold design and process iterations. A more efficient approach is envisioned where a solidification model is generated and utilized to accelerate process development. Towards this end, the directional solidification (DS) of simple geometrical shapes in a crystal grower apparatus has been simulated with MARC finite element nonlinear thermal analyses.The finite element models of cylindrical (2D) and rectangular (3D) cross-section bars in the DS environment are presented. Temperature dependent properties, the impact of latent heat of fusion and a time-dependent radiation boundary condition constitute the more salient features of the MARC models. Solidification zone thermal behavior is predicted during the withdrawal transient for the specific case of nickel based superalloys grown in ceramic shell molds. Comparisons of analytical results with experiments demonstrate notable prediction accuracy. INTRODUCTIONSingle crystal and uni-directional crystal turbine blades require tightly controlled conditions if metallurgically and mechanically acceptable parts are to be produced. Gated blade geometry and process parameters must be precisely determined if incorrect grain structure, orientation and shrinkage are to be avoided. Since purely experimental development programs designed to evaluate these parameters can be excessively costly and time-consuming, an effort combining engineering analysis and verification by experiment has been initiated at Pratt & Whitney. Comparison of analytical predictions and measured data for geometries simpler than a turbine blade, namely cylindrical and rectangular bars, comprised the initial stage of this effort. Subsequent tasks involve modeling geometries of increasing complexity and ultimately the simulation of the directional solidification of the turbine blade, shown schematically in Figure 1. This paper summarizes the results of the initial stage of the effort."

Jan 1, 1986

By K. H. J. Clarke

SINCE the beginning of this century the non-ferrous mineral industry has contributed $17,809,-000,000 to the economic growth of Canada. To contemplate the vast amount of investment capital required and the resultant beneficial distribution of these billions of dollars for labour, transportation, supplies, taxes and dividends, challenges the imagination. It is the purpose of this paper, (a) to trace the development of the industry since its formative period to the present; (b) to discuss the current situation and problems; and ( c) to attempt to peer into the hazy future. Although there are 21 metals currently being produced in Canada which are classified as non-ferrous, or as alloying metals, copper, lead, zinc, nickel-the metals which will be discussed in this paper-constitute almost 60 per cent of their total value. ;The story

Jan 1, 1961

By J. E. Chilton

The Bureau of Mines has developed a portable flammable gas detecting system for estimating the flammable gas concentrations in a mine containing one or more combustible gases at concentrations up to 100 vol pct. With this portable detecting system, mine rescue or recovery personnel can quickly determine if they are working in a potentially explosive gas atmosphere and either leave the area or make appropriate changes in the fresh air ventilation of the mine to render the area safe. The detecting system uses a commercial, intrinsically safe, flammable gas detector with a range from 0 to 5 vol pct methane (CH4). The flammable gas detector has a catalytic heat-of-combustion sensor that can detect all flammable gases that would be encountered in a mine including methane (CH4), ethane (C2H6), carbon monoxide (CO), and hydrogen (H2). To determine the mine gas concentration, the rescue worker dilutes a sample with fresh air carried within the detecting system. The concentration of the diluted sample is then measured with the permissable flammable gas detector. The actual mine gas concentration is calculated from the product of the indicated diluted gas concentration and the system dilution ratio using a pocket calculator or the nomograph on the side of the unit.

Jan 1, 1987

By J. F. K. Brown, E. E. Roecker

For three years The Hudson Coal Co. has used egg anthracite instead of coke in its foundry cupola. It has long passed the stage of being told it cannot be done—the metal would be cold, of poor quality, or the speed of operation would be low. From observation, from use and from test. we know that our metal is about average; the cast iron invokes no adverse comment from the machine shop and the speed suits our foundry requirements. We have there-iore resolved into practice anthracite combustion processes in an industrial furnace formerly using coke, under conditions suitable to our needs. When it comes to translating what we know into use in another cupola, however, where operating conditions may be different, or to explaining why, with seemingly the same conditions in our own cupola, we have attained sometimes a temperature of 2800° in the metal and at another time 2600°, or a speed of 5 tons per hour against 2 35 tons per hour, we cannot do it. We cannot do this because there seems to be an unbridged gap between laboratory ideas on combustion and practical ideas on com-bustiqn, which we have been unable to cross in terms understandable to us as practical consumers. This gap or bridge centers around the problem of how combustion actually takes place; and we believe it is controlled by two factors: (I) the character of the surface of the fuel and (2) the space provided and needed within which the oxygen of the air is allowed to or can act on that surface. It has long been contended on behalf of coke that porosity is an important factor in combustion, although, admittedly, there are two schools of opposing thought on this question, as revealed in technical literature. It has been understood generally that a light, porous coke is the best metallurgical fuel because there are more square inches of carbon exposed to the blast of air, therefore more useful carbon-dioxide reactions can take place in the given space between the entrance of the air and the point where useful work is done. It is now our general idea that the heavier and the harder the coal, the better the metallurgical fuel, provided the surface of that fuel is suitable for fast reaction with the oxygen. Time and Space A cupola is loaded in layers of fuel and iron. The horizontal line where the first charge of iron rests on the coal is the top of the bed coal. With us that is 22 in., usually, above the tuyeres where the air enters. This means 600 lb. of coal. Every subsequent coal layer is 100 to 125 lb. of coal, and that 100 to 125 lb. of coal melts 1000 lb. of iron at around 2700° in the ladle. This quantity of coal represents a 3-in. layer spread across the cupola. The question arises: If this 3 in. of coal will melt 1000 lb. of metal, why was it necessary to use 600 lb., or 22 in., of coal beneath and between the first charge of iron and the air entrance?

Jan 1, 1944

By E. E. Roecker, J. F. K. Brown

For three years The Hudson Coal Co. has used egg anthracite instead of coke in its foundry cupola. It has long passed the stage of being told it cannot be done—the metal would be cold, of poor quality, or the speed of operation would be low. From observation, from use and from test. we know that our metal is about average; the cast iron invokes no adverse comment from the machine shop and the speed suits our foundry requirements. We have there-iore resolved into practice anthracite combustion processes in an industrial furnace formerly using coke, under conditions suitable to our needs. When it comes to translating what we know into use in another cupola, however, where operating conditions may be different, or to explaining why, with seemingly the same conditions in our own cupola, we have attained sometimes a temperature of 2800° in the metal and at another time 2600°, or a speed of 5 tons per hour against 2 35 tons per hour, we cannot do it. We cannot do this because there seems to be an unbridged gap between laboratory ideas on combustion and practical ideas on com-bustiqn, which we have been unable to cross in terms understandable to us as practical consumers. This gap or bridge centers around the problem of how combustion actually takes place; and we believe it is controlled by two factors: (I) the character of the surface of the fuel and (2) the space provided and needed within which the oxygen of the air is allowed to or can act on that surface. It has long been contended on behalf of coke that porosity is an important factor in combustion, although, admittedly, there are two schools of opposing thought on this question, as revealed in technical literature. It has been understood generally that a light, porous coke is the best metallurgical fuel because there are more square inches of carbon exposed to the blast of air, therefore more useful carbon-dioxide reactions can take place in the given space between the entrance of the air and the point where useful work is done. It is now our general idea that the heavier and the harder the coal, the better the metallurgical fuel, provided the surface of that fuel is suitable for fast reaction with the oxygen. Time and Space A cupola is loaded in layers of fuel and iron. The horizontal line where the first charge of iron rests on the coal is the top of the bed coal. With us that is 22 in., usually, above the tuyeres where the air enters. This means 600 lb. of coal. Every subsequent coal layer is 100 to 125 lb. of coal, and that 100 to 125 lb. of coal melts 1000 lb. of iron at around 2700° in the ladle. This quantity of coal represents a 3-in. layer spread across the cupola. The question arises: If this 3 in. of coal will melt 1000 lb. of metal, why was it necessary to use 600 lb., or 22 in., of coal beneath and between the first charge of iron and the air entrance?

Jan 1, 1944

By James H. Gary

Data regarding the composition and physical properties of Florida land-pebble phosphate-waste slime are presented, and the feasibility of dewatering and beneficiating the slime by several different methods is discussed. Chemical analyses, electron micrographs, and X-ray diffraction data showed that principal constituents of the slime included quartz, attapulgite, and flaorapatite. Viscosity of the slime changed with pH; thixotropic, Newtonian, and rheopectic states were observed as the pH increased. Use of various flocculating agents was not effective in improving thickening properties of the slime. Dewatering tests using pressure filtration showed that temperature influenced the filtration rate more than pressure; the filtration rate at 165° C was tenfold that at room temperature. Selective flotation of the slime, using two different processes, gave promising results. About 25 pct of the phosphate was recovered in a concentrate assaying 31 pct P205, Other tests demonstrated that the slime could be successfully fractionated at 20-microns using a hydrocyclone. In hydrometallurgical tests about 80 pct of the phosphorus and alumina were chemically extracted from the slime using sulfuric acid. Limited bacteriological studies made of the slime showed that several types of microorganisms were present and grew in the material despite the presence of fluorine-bearing minerals.

Jan 1, 1963

By S P. Young, K R. Monro

Reducing metal prices have forced mining operations to become more efficient and innovate in order to do more with the existing base. Much of this effort has focused on improving the efficiency of load and haul operations. The key to this is to understand and quantify where delays and missed opportunities exist. Metrics such as utilisation of availability, efficiency utilisation and asset availability are helpful indicators of performance; however, uptime-based time usage models and performance analysis tools using productive operating time models help to identify additional improvement opportunities.Phu Kham is a copper-gold mine operated in the Lao People’s Democratic Republic (Laos) since 2008 by PanAust Limited. The mine is a single large open pit of 450 m depth, running a fleet of 51 100 t class rigid dump trucks and 300 t and 200 t shovels controlled with the aid of a fleet management system in order to achieve ex-pit material movements of 56 Mt/a.Commencing in late 2014, a range of initiatives were implemented in order to improve the efficiency of the mine haulage fleet. These include hot seating of all operator changeouts via changeout ramps, split shifting of crews to minimise queuing delays, maximising blast volumes and minimising blast event days to reduce blast exclusion delay events including opportune refuelling of equipment during blasting events, inspections of trucks during refuelling events, implementation of a dedicated haul road services team to help reduce wet weather related delays and infrastructure development for haul path efficiency improvements.These and other initiatives have allowed the mine haulage fleet utilisation of availability (UofA) to be sustainably increased from 85 per cent to 97 per cent (see Figure 1), efficiency utilisation to increase from 85 per cent to 90 per cent, and productive operating time (POT) to increase from 73 per cent to 84 per cent. The corresponding increases in efficiency of the haulage fleet has allowed an equivalent reduction of eight haul trucks from the fleet to meet continuing life-of-mine production requirements.CITATION:Monro, K R and Young, S P, 2016. Truck haulage improvements at the Phu Kham mine – the journey to 97 per cent utilisation of availability, in Proceedings International Mine Management Conference, pp 339-346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By Bruce A. Kuyper

Routine core drilling at the Cove deposit failed to confirm gold-silver grades and length of intercepts observed in reverse circulation drilling. A drilling program was designed to ascertain whether the disparity was due to problems with reverse circulation drilling techniques, core drilling techniques, or the erratic nature of the gold-silver mineralization. Special sampling devices and core drilling methods were employed. Data obtained from core-reverse circulation twins showed that down-hole contamination during reverse circulation drilling accounted for much of the variation between reverse circulation and core drill results. Down-hole contamination occurred as a result of high ground-water inflows eroding friable vein material from hole walls.

Jan 1, 1991

By J. W. Hunter, J. H. Jacobs

"Approximately 355 tons of nodules from Chamberlain; S. D., ore were processed in the 1-ton-per-day electrolytic-manganese pilot plant of the Bureau of lanes at Boulder City, Nev., in a continuous 3-month operation. The ore, ground to minus 48-mesh, was found to be amenable to leaching with acid directly or after roasting under reducing conditions in a Skinner muffled multiple-hearth furnace.Unroasted ore gave an acid-leach extraction of 84 to 88 percent of the manganese, which after neutralization showed an over-all extraction of between 81 and 85 percent of the manganese. The amount of iron extracted varied, but it was always,enough to permit the use of ammonia for neutralization.Roasted ore showed an acid-leach extraction of 89 to 91 percent of the manganese. A large amount of iron went-into solution, so that it was not economical to neutralize it entirely with ammonia. By neutralizing with calcine to a pH of 5.0 and completing -neutralization with ammonia to a pH of a.5 an over-all manganese extraction of 84 to 86 percent was obtained. The slight increase in. extraction on roasted ore probably would not justify the cost of roasting.Acid consumption averaged 1.75 pounds per pound of manganese extracted. Settling rates of the residue in leach solution were to slow to permit clarification in thickeners, but a Moore vacuum leaf filter proved to be satisfactory. Purification of raw leach solution was .accomplished readily by hydrogen sulfide with a low gas consumption. Electrolysis was normal, without difficulty, and with -current efficiency ranging between 62 and 66 percent.The use of Chamberlain modules for the production of electrolytic manganese would result in an operating cost of 0.8316 cent per pound higher than the cost of producing electrolytic manganese from Three Wids ore."

Mar 1, 1946

By Harry R. Nicholls

A simple economical method has been developed for determining the in situ longitudinal and shear velocities in rock from which its elastic constants can be calculated. By detonating small charges of high explosives in shallow drill holes near a free surface, both longitudinal and shear waves were generated simultaneously. Accelerometers and velocity gages mounted to the rock surface were used to record the arrival time for both waves over travel path lengths from 50 to 450 feet, Measurements were made in two rock types. From the arrival time measurements, the longitudinal and shear wave velocities were calculated. From these velocities and the density of the rock, the elastic constants were calculated. The dynamic elastic constants of drill core samples of the two rock types were determined in the laboratory by the resonant-frequency method, The lab- oratory and in situ elastic constants are compared and significant differences noted. In general, there is less spread in the in situ data than in the laboratory data, and Poisson's ratio does not fall outside the theoretical limits for the in situ data as is often the case for laboratory-determined elastic constants.

Jan 1, 1961

By David Hanson, Sean Warren, Chaparral Berry

"Coal bumps, also referred to as dynamic failure events or coal bursts (Lawson, Weakley, and Miller, 2016), continue to be a hazard in underground coal mines. While current design methods have significantly reduced the occurrence of coal bumps, they have not been completely eliminated. This paper investigates a correlation between coal compositional components, coal molecular structure, and probability of coal bumps in an effort to deepen understanding of coal behavior in an effort to reduce hazards in underground coal mines.Samples from the Penn State Office of Coal (PSOC) Department of Energy Coal Samples (DECS) were obtained for Fourier Transform Infrared Spectroscopy (FTIR) analysis using the KBr pellet method. Peaks indicative of the coal molecular structures were obtained using spectral integration software. These data, combined with published elemental data, were compared to historic bump occurrence in order to establish a possible correlation. Finally, results based on multivariate analysis of the elemental and FTIR data with bump status as the dependent variable suggest that elemental sulfur and molecular structure can be used as an indicator of bump susceptibility within the sample set considered.INTRODUCTIONThe study of coal requires consideration of multiple variables: percentages of organic and inorganic components, organic component origins, coal age, pore structure, cleat density, elemental composition, etc. Examining coal in situ increases the number of variables, such as coal depth, seam thickness, surrounding stratigraphy, and so forth. This collection of variables influences the subsequent behavior of coal simultaneously, and weighing their relative impact is a challenge for researchers. “A problem never exists in isolation; it is surrounded by other problems in space and time” (Ackoff, 1956). Having a substance such as coal that we know so much about, and yet so little, we have to ask what can be learned.An experimental study using Fourier Transform Infrared Spectroscopy (FTIR) was undertaken to determine if the chemical structure of coal contains information which may lead to a better understanding of triggers or attributes which may, in turn, lead to an increased probability of a dynamic failure event. While a full analysis of the factors driving dynamic failure are beyond the scope of this study, it is possible that a better understanding of the chemical structure of coal will lead to an increased knowledge of its inherent behavior, including its propensity to burst."

Jan 1, 2019