Search Documents

By R. R. Sayers

There is probably no industry , trade , or art in which mercury is used but what has produced some cases of mercury poisoning . This is true of the mining and smelting of mercury , where the hazard has long been recognized . When the ore contains free mercury or the more soluble salts , and when the workings are underground and are poorly ventilated , cases occur , but there are a far greater number of cases among the employees about the reduction works . 3 In 1863 William V. Wells visited the mines at Almaden , * Spain , which were worked by convicts . He reported that the men at the furnaces suffered severely , being able to work only about one week out of four , when it was necessary to transfer them to places where the exposure was less . He states that "pale cadaverous faces and leaden eyes are consequences of even these short periods . " Mercury , like lead , when absorbed in small amounts at intervals , as daily, over an extended period of time will result in symptoms of poisoning . This is due to the fact that the mercury is eliminated from the body more slowly than it is absorbed . The frequency and severity of cases of mercury poisoning are far less with modern methods of mining and recovery of the metal than formerly . However , further reduction is possible and much can be done by both the workmen and the operators by following the proper precautionary measures , some of which are described in this chapter .

May 1, 1922

By Ashish Ranjan Kumar, Steven Schafrik, Oscar Velasquez

Flooded-bed dust scrubbers installed on continuous miners use fibrous type multi-layered filters to capture dust from the airstream. Prolonged operations of the scrubber could lead to filter clogging due to dust accumulation. This results in reduced flow through the scrubber and elevated dust levels in the mine environment. This paper compares the performance of a conventional fibrous screen filter and a novel impingement type dust filter. The impingement filter is a self-cleaning system and was designed to have a resistance similar to the fibrous filter. The cleaning efficiencies for these filters were computed using iso-kinetic sampling and optical counting of coal dust particles in a clean unclogged state. The cleaning efficiency of the impingement filter also increased with an increase in particle size and was comparable with the conventional fibrous filter. The cleaning efficiency of the fibrous filter improved significantly with an increase in water flow. The non-clogging nature of the impingement filter and minimal maintenance requirement makes it an attractive alternative to the conventional fibrous type filter in mining applications. The research also proposes a term called ‘filter performance factor’ to compare the performance of different filters under similar operating conditions.

Sep 19, 2020

Jan 1, 1893

By Kevin W. Harris

Multiple-seam coal mining is a major issue in underground coal mining that adds additional complexity to the practice of ground control. As reserve exploitation is driven by economics, it is now difficult to mine coal without the existence of previous workings above and/or below the active seam; this is particularly true in the Appalachian coalfields. The frequency in which problematic multiple-seam interactions are now encountered has resulted in significant research regarding the underlying mechanisms of the problems and methods of mitigation. In the last few decades, a great deal has been learned about these interactions and the ability to minimize problems associated with these hazards has greatly advanced, resulting in better economics and improved safety. Minimizing the adverse effects of stress interactions often requires a thorough understanding of site-specific geotechnical parameters and previous mining geometry. This is especially evident in bump-prone ground, where pillar behavior is highly dependent on local conditions. This paper presents a case study in a deep cover, Central Appalachian coal mine where three bump events occurred. Initially, empirical design software was used in an effort to analyze the situation and prevent further instability. The empirical study proved ineffective. A detailed investigation of the bump events using the boundary element software LaModel 3.0 was then performed. This study resulted in a site-specific calibration standard that will be applied in numerical pillar design for the remaining reserve.

Jan 1, 2014

By J. D. Wright

This paper describes current milling practice at Endako Mines Ltd., a molybdenum producer in central British Columbia. The various steps in the crushing, grinding and flotation of the ore are outlined, with emphasis on the metallurgy of the latter operation. Tailings disposal and concentrate assaying methods are also described.

Jan 1, 1969

By Jose Agapito

Roofbolts with expansion anchors have been used at White Pine for more than twelve years, but always with an understanding that their performance was not entirely satisfactory. Some bolts fell out, some were obviously loose, and, when roof failures did occur, very few bolts actually broke. Obviously, there was an anchorage problem. A program was started in May, 1967, to define the problem and to solve it. This paper describes briefly those parts of the program which led to the development of a roofbolt assembly which performs much better in the medium-hard rocks at White Pine. As a result of the changes, significant improvements were found in the torque:tension, tension loss, and pull tests.

Jan 1, 1970

By D. Kovachevich, M. A. Pfeifer

"A t remote locations typical of mines and associated ore processing plants, diesel electric generators are ideally suited for power plants due to their inherent operating flexibility, efficiency and reliability. In recent years rapid escalation in fuel and related transportation costs has made extensive waste heat recovery from generating sets financially attractive to a much greater extent than previously.The paper outlines key considerations during planning and design stages for utilizing the various waste heat sources available to best advantage. Based on two /980 mining projects built in the Canadian Arctic, data is presented on potential operating and capital costs savings. A review of heat balances, engineering flow diagrams and major equipment selections for process and building heating systems utilizing waste heat is included.IntroductionResource projects increasingly occur in remote areas requiring on-site self sufficiency in electrical power generation. For such projects, the low- or medium-speed turbo-charged diesel engine is very often the preferred choice as a prime mover for the generating sets . It is inherently reliable, has good response to load changes and has comparatively high fuel efficiency over a wide load range . From a project execution standpoint, It is capital cost- competitive and procurement lead-time normally ' fits ' within tight schedule constraints. In addition, its potential for waste heat recovery is excellent , particularly in northern climates where space heating requirements are usually substantial, and also where there a re requirements for heat for process and plant services.The high cost of fuel , with add-on transportation costs , provides a major incentive to fully exploit the available waste heat recovery potential o f such installations.As a result of the rapid escalation in the price of petroleum products following major crude oil price increases in 1973 and again in 1978-79, liquid petroleum fuels, having the desirable properties of comparatively high heat content and transportability, are no longer 'cheap' commodities and have become so valuable that industry has widely undertaken serious conservation efforts.Currently, it appears that petroleum cost trends of the 1970s may not continue, at least in the near term, and that we may see somewhat reduced energy costs for a time. In the longer term , and certainly within the life spa n of major projects, however, it is generally believed to be inevitable that these fuels will be increasingly expensive . Energy costs are today a major operating cost for remote minerals processing plants and will remain so for the foreseeable future.In order to meet the economic challenge posed by high energy costs, future projects should be thoughtfully planned from the outset with the goal of minimizing energy requirements and maximizing the use of waste heat recovery to meet such requirements. There is also considerable potential for significant energy savings by retrofitting of existing installations."

Jan 1, 1984

By B. Wasmund, M. Parravani, M. Jastrzebski, Z. Coull

"One of the main drivers of overall profitability of pyrometallurgical vessels is refractory lining campaign life. Increased economic pressure to improve vessel life requires innovative solutions to the problem of refractory cooling. Hatch has recently developed a high-intensity, waterless cooling system that bridges the performance gap between external shell cooling and internal water-cooled copper elements. External shell cooling has a limited effectiveness in protecting the refractory lining, because it is thermally insulated from the hotface of the lining by its thickness. This situation does not improve until the lining itself has become worn near the end of the campaign. The patented technology developed by Hatch overcomes this problem by positioning high-velocity air-cooling channels within the lining, closer to the hotface where the cooling benefits can be realized throughout the entire duration of the campaign. The current paper presents the development and application of Internal Air Cooling technology as well as results from the pilot campaign in an operating commercial vessel. Various adaptations for this novel, cost-effective and inherently safe system are also discussed."

Jan 1, 2015

By M. J. Beus

Researchers at the U.S. Bureau of Mines have developed personal-computer-based data acquisition, instrumentation, and mine visualization and modeling techniques to evaluate a mine accessway in a deep hard-rock mine in northern Idaho. These techniques were applied to a mine shaft in a large silver mine that has been in operation for many years. A very deep, rectangular, timber-supported shaft extending to depths exceeding 2.3 km (7,500 ft) had been deforming continuously as a result of nearby mining, resulting in operational problems. Preliminary visual observations and rock and support monitoring confirmed that severe diagonal distortion was occurring. Extensive field measurements and data analysis confirmed initial observations, provided insights into the cause of deformation, and defined a general approach to structural modeling. Computer analysis of the problem was initiated by developing a three-dimensional model of the terrain. This represented a volume of rock approximately 80 km3 (40 x 1010 ft3) and an area on the surface surrounding the mine 9 km2 (3 square miles). Based on this model, a three-dimensional, finite- element analysis was conducted to establish boundary conditions for sequentially more detailed two- and three-dimensional submodels of the shaft area. Results from the computer study are being used to develop new approaches to mine design and to provide design guidelines for deep mine accessways subject to severe rock-mass loading conditions.

Jan 1, 2010

By R. W. Huber, R. C. Wiley, V. C. Petersen

"Three arc- melted ingots, two of a t itanium-7 percent manganese all oy and the third of unalloyed titanium, were forged and rolled into 3/ 4-inch plate; comparative data were obtained on these processes. The finished plate, part of which was used by the Naval Bureau of Ordnance, was tested for mechanical and other properties.These properties were correlated with sponge purity, forging technique, rolling temperature, and cooling rate from the rolling temperature. For the alloy material, transformation data were obtained, and their age-hardening characteristics were studied. The temperature-impact relationship was established for rolled sections from all three ingots.INTRODUCTIONArc -melted ingots of unalloyed titanium and a titanium-manganese alloy were fabricated into plate under closely controlled conditions by personnel of the Metals and Alloys Section, Physical Metallurgy Branch, Bureau of Mines, College Perk, Md. This program was cosponsored by the Naval Bureau of Ordnance. Bureau of Mines interest lay in correlating the processing procedures with the mechanical properties of the finished plate.Considerable data have been published recently on constitution diagrams and properties of titanium-manganese alloys in genera1. 3/ 4/5/6/ However, little if any correlation between processing schedules and end results has been published, particularly with respect to the present commercial production of the proprietary titanium manganese alloys . Several factors in the production of titanium and titanium alloys have a pronounced influence on the physical and mechanical properties of the finished product: (1) The degree and nature of impurities in the base materials, ( 2) the amount of impurities introduced during the melting cycle and their distribution, (3) the homogeneity of the alloy, (4) forging, (5) rolling, and ( 6) final heat-treating cycles. All of these item£ are important from a metallurgical standpoint in producing the desired end properties in the metal."

Mar 1, 1955

By A. G. Mayton, D. H. Ambrose, C. C. Jobes, N. K. Kittusamy

In a systematic study, the National Institute for Occupational Safety and Health (NIOSH) evaluated seat designs in low- and mid-seam shuttle cars during production operations at two underground coal mines in southern West Virginia. The purpose was to support, with additional data, earlier findings that NIOSH ergonomic seat designs (featuring viscoelastic foam padding and lower-back support) may help reduce health risks to operators of coal mine shuttle cars. Eight shuttle car operators evaluated seven seat designs (one already in use in each vehicle and five NIOSH designs) relative to perceived and measured whole-body vibration (WBV) exposure (including vehicle jarring/jolting) and discomfort. Operators’ perceptions using a visual analog scale (VAS) and questionnaire ratings were compared with International Standards Organization (ISO) 2631-1:1985 fatigue-decreased proficiency (FDP) limits and measured WBV levels on low- and mid-seam shuttle cars. Objective and subjective data results indicated that NIOSH seat designs (with added adjustability, lower-back support and improved seat padding) performed better to reduce vehicle jarring/jolting levels and that shuttle car operators favored them over existing seat designs. The NIOSH low- and mid-seam shuttle car seats showed 45 to 77 percent better performance in FDP and 9 to 60 percent better performance overall in operators’ ratings. Considering the VAS results for low- and mid-seam shuttle cars under no-load conditions, operators rated the level of jarring/jolting 18 to 89 percent lower with the NIOSH seats. Reductions in measured vehicle jarring/jolting were 19 to 46 percent for the three-directional vector sum accelerations relative to the existing seats on the low- and mid-seam shuttle cars. Questionnaire responses indicated that operators for both shuttle car models rated NIOSH seat designs as more comfortable overall. Vehicle operators most frequently suggested adding armrests to improve the seats on the mid-seam shuttle car. A suggested improvement for the low-seam shuttle car was to make the seat a better fit for the operator compartment, which would enhance clearance between the operator and vehicle controls and allow for better seat adjustment and operator visibility.

Jan 1, 2009

By G. C. Hodgson

Specification and Tests of Rope Wire Chemical Analysis: The range in composition of steel used in the manufacture of wire rope is as follows: Carbon 0 4 to 0.9 per cent Manganese 0 4 to 0.8 Sulphur Not above 0.04 Phosphorus Not above 0.04 The carbon and manganese content are varied according to the gauge of wire to be drawn and the tensile strength required. Generally speaking, best results are obtained from heats where the melt is not of too large a tonnage. The amount of reduction and patenting of the wire is left to the wire maker, who thus has a free hand in meeting the balance of the specification.

Jan 1, 1931

"Chairman: Professor E. P. PFLEIDER Rapporteur: Mr P. R. JANISCHPapers:Optimum design of an open pit by D. A. PhillipsAn open pit design system for stratiform ore bodies by L. A. J. Pronk van Hoogeveen, J. R. Cutland and M. WeirAn open pit design model by R. H. Robinson and N. B. PrennThe Chairman in opening the session highlighted the current situation in the United States of America where some 85 to 90 per cent of all mining (except for coal) is done by open pit methods, and where some 40 per cent of the coal is mined by open pit. The South African industry is, of course, dominated by the deeper level underground gold mines; however, with the aid of an extensive open-pit technology developed in other countries, South African companies arc continuing to explore possibilities of open-pit exploitation of base mineral, coal and diamond deposits. Several successful ventures are already in operation at Phalabora, Optimum Colliery, Kimberley and elsewhere, and South Africa is undoubtedly benefitting in this regard by drawing on the experience of others.The papers of this session were therefore particularly pertinent, particularly when viewed in conjunction with those presented at an earlier South African conference devoted specifically to open pit mining.Two themes dominated the discussion which followed presentation of the three papers at this session. The first related to the practicability of using the reported techniques as a tool for management, and their acceptability as such to mine management. This was, of course, not peculiar to this particular session, but rather the major point of debate over the entire conference.The second theme concerned the reliability of the initial drill hole data on which any open-pit design must necessarily be based. This gave added emphasis to the problem of practicability, for no management is likely to accept an elaborate pit design unless confidence can be placed in the ore reserve assessment.In noting these two features of the discussion, it should be remembered that all the three papers dealt largely with design and pre-planning; there was an unfortunate lack of papers or discussion on the subject of controlling the day-to-day mining of open pits, and this is an area where the potential impact which can be made by the computer is even greater.In introducing his paper, Mr D. A. Phillips pointed out that it was concerned only with optimization, and that it therefore assumed, firstly, an adequate subdivision of the orebody into ore blocks characterized by grade, rock type, structure, etc., and, secondly, an acceptable forecast of costs and mineral prices in order to generate a suitable profit matrix. However, programs dealing with these problems for both massive, disseminated and stratiform ore bodies are available to Roan Consolidated Mines. The method of optimization which he had described had been used on a region split into 28 000 blocks, for which the program used three hours of C.P.U. time on an IBM 360/40 computer. The computer design had provided a three per cent improve¬ment on a normal design of the same area."

Jan 1, 2014

By Michael P. Hardy

The report described improvements and applications of the Hybrid Computer facility. Improvements implemented under U.S.B.M. Contract H0252035 included expansion of the capability to model nonlinear seam behavior, installation of a color video output display monitor, and further development of software capabilities. To demonstrate the capability of the system, firstly, the influence of nonlinear seam behavior response to the occurrence of coal mine bumps was fully investigated and secondly, the effect of improper mining sequence on bump occurrence was demonstrated. In addition, the system was applied to the analysis of a series of practical coal mine problems. Mines in three coal seams were analysed to investigate the parameters which contribute to the occurrence of coal mine bumps.

Jan 1, 1977

By N Phillips

Fosterville gold mine recently celebrated production of its one millionth ounce of gold based firmly within a history of refractory sulfide gold mining. Compared with other Victorian gold mines, the disseminated nature of the sulfide gold is a deposit style with low estimation variance combined with established processes to accurately delineate the controlling structures. The systems in place had been established and have worked effectively for the majority of the one million produced ounces.By the end of 2014, diamond drill campaigns targeting the lower Phoenix orebody at depths of 800 m below surface began showing a change to the nature of the gold within the deposit. Coarse visible gold within 0.5–2 m thick quartz carbonate veins were being intersected with regularity showing the emergence of a different zone of gold mineralisation.Data about the new and exciting discovery couldn’t be gathered fast enough, however, established systems and processes throughout the geology and processing departments were not developed to handle a coarse gold environment. Change would be commensurate with the size and scale of the discovery, and new learnings would need to be implemented quickly to keep in front of a mining schedule that was focused on producing tonnes due to the dropping grades of the sulfide ore.Gold assays being returned were showing that the gold nature was different to those of other Victorian deposits. Comparative to the highly nuggety nature of gold found in other Victorian goldfields, the fine grained gold accumulations were dispersed in relatively consistent narrow linear trends grading consistently into the hundreds of grams per tonne. New drill intersections were being returned by the day and research to find developed orebodies that had published information into how to handle such a rapid change yielded few examples.The challenge was to review and set new standards with regards to handling an orebody that transitioned the very nature of the gold being mined. This involved reviewing all steps in the estimation process including data capture and quality control and quality assurance through to mineral liberation through the mill. Difficulties also involved finding analogous orebodies that consisted of both free milling and refractory ores that were dealing with drill assays that were measured as percentages of gold.CITATION:Phillips, N, 2017. Fosterville gold mine – breaking the mould for Victorian gold, in Proceedings Tenth International Mining Geology Conference 2017, pp 393–400 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES

Lithium-ion (Li-ion) battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12 V and 24 V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicate that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

Jan 1, 2024

By David White

Jan 1, 1925

By J. M. Singer

The Bureau of Mines investigated the threshold of dispersal of monolayers and piles of rock dust, anthracite, and Pittsburgh seam coal dust in a small wind tunnel that simulated a coal mine gallery, with the objective of preventing or limiting the formation of flammable dust clouds. The effect of selected variables on entrainment velocity was examined. Mode of entrainment and flow processes in the wake region of dust configurations were investigated by means of high-speed motion pictures. Significant results were as follows: 1. Local minimum air velocities required for dispersal were only slightly higher for shallow dust ridges than for dust particles. 2. Minimum velocities for entrainment of dust particles from smooth glass and coal surfaces increased in the order rock dust, anthracite, Pittsburgh seam coal. 3. The mechanism for dispersal of dust poles depended significantly on dust pile geometry, cohesiveness of dust, bulk density and compaction of dust, adhesive surface, and vibrations perturbing the supporting surface.

Jan 1, 1969

By R. H. King

The Deserado Mine of Western Fuels- Utah Inc. installed a micro-computer based mine wide monitoring and control system for mine environment, beltway fire protection, belt operating parameters, and equipment power utilization. The Colorado School of Mines was funded by the U.S. Bureau of Mines to document, evaluate, and report on the system design, procurement, installation, tests, and operation. This paper results from that project. The paper compares planned activities such as installation and start up, procurement contract specifications and system layout with actual performance to develop recommendations for future installations by mine operators.

Jan 1, 1987

By Tim O’Neil

Tire companies have historically used the mining industry as a platform to launch new technologies. And the mining industry has been receptive to that. So, while developing its Two Piece Assembly, Goodyear noted a number of trends in the mining industry: •The global market sophistication of equipment and operations requires the packaging of products and services to provide the best return on investment. •Industry consolidation and growth have resulted in fewer, more powerful mining houses, leveraging purchasing power in the marketplace. •User productivity demands continue to drive original equipment manufacturers to develop higher pay-load equipment. •Technology needs include improved ergonomics, to reduce fatigue and increase operator productivity. •Increased laws and environmental regulation prohibit on-site whole tire disposal practices.

Jan 1, 2003