Search Documents

By Kenneth G. Broadhead

Four applications of radiotracer techniques in metallurgical research are described: (1) In electrowinning tungsten from scheelite, molybdenum 99 was used to detemine the molybdenum concentration of the fused alkali-phosphate bath and the electrowon tungsten; (2) an attempt to detemine the solubility of tagged ceric oxide in molten CeF3-BaF2-LiF was unsuccessful, but a high rate of cerium ion exchange was observed; (3) iron 59 was added to cerium during casting and used to follow the migration of iron during solid state electrolysis; (4) radiotracers were used in developing special analytical techniques applicable to high-purity rare-earth metals produced by molten salt electrolysis.

Jan 1, 1963

By Charles D. Litton

Laboratory experiments were conducted to determine the responses of a prototype smoke detector and a commercially available photoelectric smoke detector to smoke particles generated from various combustion sources. The prototype smoke detector combines optical scattering measurements with ionization chamber measurements in order to reduce/eliminate nuisance alarms due to the presence of airborne dusts or diesel exhaust particles. The commercially available smoke detector is designed for use in harsh environments where airborne dust represents a major problem due to both nuisance alarms and detector contamination. In the experiments, the responses of the two detectors were measured when exposed to smoke particles from the exhaust of a diesel engine and from a variety of fire sources, including wood, coal, styrene butadiene rubber, and No. 2 diesel fuel. For the solid fuels, data were obtained for both smoldering and flaming combustions. This report describes the experiments, their results, and the use of these results as they apply to early-warning fire sensors capable of the rapid and reliable detection of fires in atmospheres that may or may not be contaminated by either airborne dust or the products produced from diesel engines.

Jan 1, 2008

By Israel Liebman

The Bureau of Mines developed three types of passive water barriers for suppressing slow-moving coal dust explosions. One type is a modification of a conventional tub barrier and depends on the dynamic pressure generated ahead of an explosion to tilt the tub to release its water and suppress the explosion. The other two barriers operate in response to an increase in static pressure developed ahead of the explosion. Tests indicate the first barrier begins to release its water at air speeds as low as 50 ft/sec, and the second and third barriers will operate at a rise in static pressure as little as 0.5 psi. All three barriers were found to be effective in suppressing coal dust explosions propagating at speeds as low as 100 ft/sec. A plan is described for installing a water barrier in a working mine on a trial basis.

Jan 1, 1976

By C. W. Dunham

DESIGN of the structures for the Morenci Reduction Works involved many interesting problems. Naturally, the chief purpose of these structures is to house and support the equipment and other things necessary for or incidental to the conduct of production. hence most of the features of the design were developed to suit these particular conditions; however, several are so generally applicable as to warrant description.

Jan 1, 1942

By H. E. Peterson, W. L. Anderson

"INTRODUCTION The great demand for tungsten incident to the war has led to the exploration of a large number of low-grade tungsten deposits. To properly evaluate the low-grade deposits it is essential to have available a dependable method of analysis applicable to all types of low-grade tungsten ores. Results reported on the tungsten content of the ores have often varied quite widely and have led to confusion. The Bureau of Mines has been requested by Government lending agencies and by companies interested in the production of tungsten to publish a general method for the determination of tungsten in low-grade ores. To meet this need, the Bureau of Mines is herein submitting two methods for analysis that have been proved on a large number of tungsten-bearing ores various types in the Bureau of Mines laboratory in Salt Lake City. Also, a third method was developed that requires no cinchonine and has proved to be applicable on most tungsten ores. The cinchonine method is the generally accepted for analysis of tungsten ores. Very reliable results can be obtained by this method if certain precautions are taken, as outlined in this report."

May 1, 1943

By C. W. JEFFERS

During the past few years the use of mechanical equipment for the loading and transportation of coal at the working face has rapidly increased . Many mining officials are of the opinion that mechanical methods have tended to reduce the hazards of mining, and a number of statements have been made to this effect . Little actual data upon which to base conclusions in regard to the relative safety of various methods of mining have been made available . While it may be possible that these systems of mechanical mining are inherently less hazardous , obvious dangers should not be disregarded in the belief that the mere act of installing mechanical loading equipment automatically brings about better accident records . The same rules and regulations , modified to meet the new regime must be applied with the same discipline as heretofore . By diligent study and application there is reason to believe that new methods of concentrated mining can be utilized with at least a possibility of increased accident performance . With the idea of preventing accidents by taking available precautions against their occurrence , attention should be directed to the dangers that exist where room and face conveyors are in operation . Due to the cost pressure prevalent in the mining industry at the present time mechanical means are often used in an attempt to decrease cost of production. The management , after having spent considerable sums of money for new equipment , is expected by stockholders and investors to show results by increasing tonnage and reducing operating costs . Consequently the operating officials apply the same pressure to local mine officials to obtain results . The natural reaction of the superintendent and mine foreman is to secure the maximum production from the new method , and unfortunately safety is frequently , if not generally , sacrificed to this end . In many instances , operators of new types of mechanical loaders are difficult to secure and after being obtained are difficult to hold , especially if the new equipment is more or less in the experimental stage . The tendency is to handle the machine operators with " gloved hands " and to permit many unsafe practices which ordinarily would not be allowed, in order to keep from antagonizing them and losing their services . Although these unsafe practices become habitual and even uneconomical , conditions thus established are difficult , sometimes impossible , to change .

Jul 1, 1930

1.1 Bituminous-Coal and Lignite Dust. - Carboniferous material having a volatile ratio of 12 percent or more by weight and a fineness such that the material passes through a No. 20 sieve. 1.2 Active Underground Workings. - Underground places in which men are required to be or to pass through in the performance of normal mining operations for the production of coal. 1.3 Working Areas. - Underground areas where bituminous coal and lignite are mined, specifically: (a) Face. - The solid surface of the unbroken portion of the coalbed at the advancing end of the working place. (b) Face Area. - The working area inby the last open crosscut in an entry or a room, including the pillar being extracted or longwall being mined. (c) Room. - A place abutting an entry or airway where coal has been mined and extending from the entry or airway to a face. (d) Crosscut (Breakthrough). - Passageways or openings cut through a pillar to connect adjacent entries or rooms. 1.4 Entry. - Underground haulageways, travelways, and airways, except working areas as defined in section 1.3. (a) Active Entry. - An entry in which coal is being mined from a portion thereof or from connected sections. (b) Parallel Entry. - Usually an intake airway parallel to the haulageway. (c) Back Entry. - Usually a return airway parallel to the haulageway.

Jan 1, 1960

By D. G. Purdy

Planning, as defined in Webster's New Collegiate Dictionary, is a detailed program of action designed to achieve an end. When developing a detailed plan to incorporate all the complex activities involved in a surface lignite mine, many elements must be carefully evaluated as to the individual and cumulative effects on the end result. The following elements are generally evaluated when planning a surface lignite mine: ? Reserve evaluation, including lignite quality characterization; ? Delineation of mining parameters, including lignite recovery factors, geotechnical factors, land control factors; ? Selection of mining blocks; ? Pit sequencing; ? Reclamation, including soil reconstruction design and land use planning; ? Overburden handling design; ? Selection of equipment; ? Sizing of equipment; ? Manpower requirements; and ? Other elements, including contract negotiations and execution, financing, investment return, operation economics, permitting and scheduling.

Jan 1, 1985

The writer presents a concise summary of eleven recent discoveries made in the Maritime Appalachian area, with suggestions for fur the research. This information may prove helpful to geologists working in other fields and to students contemplating further avenues of research in mining geology and exploration. INTRODUCTION THIS paper is not intended as a research study on the subject, but i. merely a brief review of eleven discoveries that have been made in the Canadian Appalachian area. Furthermore, this is not a critical analysis of the merits of any one geophysical method, but it is an un-prejudiced observation of how these discoveries were actually made and what techniques were apparently most fruitful. Some generalizations are attempted whicl1 may suggest further avenues of research in the field of mining exploration. The writer wishes to thank his colleagues in the field for their comments, which he was able to in-corporate into this paper. In particular, he is grateful to Dr. Paul Bevan and

Jan 1, 1963

By B A. Wake, G G. Lowder, M J. White

The Tooloom gold field is located within the New England Fold Belt in the far northeast of New South Wales, approximately 130 km south southwest of Brisbane. Gold was first discovered at Tooloom in 1857. Within a few years up to 10 000 people were mining placer gold deposits in the Tooloom valley and a few tried their hand at mining hard rock occurrences as well. Mining of alluvial gold continued in a small way at Tooloom until very recently, but only in the last few years, since Malachite Resources acquired its interest at Tooloom (now 100 per cent), has the full potential of this large, reduced intrusion-related gold field been appreciated. By the mid 1870s, once the alluvials were largely worked out, most of the early miners had made the 270 km trek north to the newly discovered Gympie gold field and Tooloom slipped into obscurity. Such was this obscurity that the Tooloom gold field was not recorded on published Government geological maps until 2001, four years after Malachite became involved. The many hard rock prospects that Malachite has identified in recent years were largely or completely unknown. Tooloom is a good example of blinkered thinking when it comes to modern mineral exploration. The New England province in NSW has long been the æpoor relationÆ to the much better known and more highly favoured Lachlan Fold Belt in NSW. It has also suffered serious neglect compared with the Queensland part of the New England Fold Belt that hosts such major gold deposits as Mt Morgan (>7 Moz), Gympie (>3 Moz) and Cracow (>1 Moz). Tooloom is proof that prospective geology does not stop at state borders.

Jan 1, 2004

By Hyunsuk Yoon, Kiho Lee, Juhyng Lee, Younghoon Jung, Junboum Park

"The environmental double pile method is presented as a device to improve the engineering properties and to clean up contamination of low-permeability soil. This method is one of the novel technologies based on the concept of one step process. It can be applied to low permeable contaminated ground for site reuse. It uses piles to improve drainage, contaminant remediation, and bearing capacity of the ground. To evaluate the on-site applicability of this technology, drainage and strength properties of the environmental double pile were assessed by a series of experiments and numerical analysis. Environmental double pile was found to be a feasible alternative method to improve contaminated soft ground.Korea is a peninsula with many coastal industrial zones. These zones are located in regions mostly underlain by soft ground with low permeability and adjacent to industrial areas that can be contaminated. Therefore, a new region-specific remediation method is required to achieve environmentally sustainable development. This research introduces the Environmental Double Pile (hereinafter, refer to as EDP) for the lowpermeability contaminated ground and focused on both contaminant remediation and soft ground improvement. Basically, the EDP is quite similar to sand compaction pile (SCP). The SCP has been studied extensively to improve soft ground (Braja 1999; Hansbo 1994; Madhav and others 1978; Taylor 1948). But unlike SCP, EDP is filled with oyster shells instead of sand and an inner pile is inserted in the center of this oyster shell filled-zone. Therefore, it is a double pile consisting of the oyster shell pile and the inner pile, as depicted in Fig. 1."

Jan 1, 2005

By W. G. Kegel

Coal mining today is confronted with numerous problems, all of which affect in some way the ability of the operator to produce profitably. The major endeavor, therefore, is a quest for cost lowering techniques. Complete belt haulage from shuttle car to river barge appeared to be a step in such a direction. A deep look into all aspects proved this to be more involved than just the installation of such a belt line. With this paper, we will attempt to present to you the problems and requirements of design and installation of an all-belt haulage system, believed to be the longest underground belt installation in the world at this time. The first and most important item is the justification of an all-belt haulage system. The following is a brief history of the coal property and the facts affecting our decision.

Jan 1, 1964

By T. Rockley, B. Goertz, S. McDaniel, J. Brune, K. Bakhsh

"Researchers at the Colorado School of Mines, under a project funded by the Alpha Foundation, have developed a working prototype of a dust sample collection device designed to determine if sufficient rock dust has been placed in an underground coal mine to prevent coal dust explosions. When used in conjunction with the Coal Dust Explosibility Meter (CDEM), the device will provide near instantaneous results on the quality of rock dusting at the tested location. The sampling device applies a pulse of air to a testing surface and collect a representative sample of mine dust based on the pneumatic entrainment process during a mine explosion. The use of both physical testing and Computational Fluid Dynamics (CFD) modeling has allowed researchers to refine the design to accurately represent the particle entrainment and optimize the sample size collected for the CDEM. The prototype is being tested in a mine environment to produce information of usability and practical aspects of mine dust sampling. This paper is a progress report summarizing the current status of sampler development. Researchers expect to have a fully developed and tested sampler in early 2016. INTRODUCTION Underground coal mines face the danger of methane and coal dust explosions. The disaster at Upper Big Branch mine (2010) has demonstrated the impact of a violent coal dust explosion that fatally injured 29 miners. Reviewing the history of coal dust explosions, researchers found that that mine operators and mine inspectors do not have a reliable method of collecting dust samples to assure that sufficient amounts of rock dust have been places to inertize the coal dust. This is a problem specifically with small mines that do not have dedicated safety departments to track rock dusting work. The aim of this research is to develop a simple, portable device that can help underground mine examiners collect dust samples from workings and test the explosibility of the sample near instantaneously. Researchers determined that the current brush-and-pan sampling method required by MSHA (MSHA 2013) is flawed in several aspects: Mechanical sampling with a brush exerts forces on the mine dust that may differ significantly from those present during an explosion. Also, U.S Bureau of Mines research (Nagy 1965) has determined that only the top 0.125 inches of the mine dust layer will be entrained in a coal dust explosion. Using a handheld pan and brush, it is difficult to correctly and repeatably sample a layer of this exact thickness. The following will describe the CFD modeling and experimental testing for the development of the prototype sampler. Researchers analyze the accuracy and performance of the prototype during the course of the build process."

Jan 1, 2015

By A. W. BELDEN

Among the investigations that the Bureau of Mines is conducting witha view to increasing efficiency in the utilization of fuels belonging to or for the use of the Government is an investigation of the processesthat take place in a foundry cupola during a melt. Some observations on the results of cupola tests of cokes at the Government fuel-testing plant in St. Louis, Mo., the coke being fromcoal from many coal fields of the United States, have been stated in a previous bulletin.s Especial attention was given to the meltinglosses that resulted from the use of different grades of coke, light and porous or heavy and dense. These losses amounted in one instance to 52.5 per cent of the iron charged and showed, in convincing manner, the need of exact information in regard to conditions in the fuelbed of the cupola.b Melting losses of iron have been fully appreciated but little under-- stood. The fact that these losses were possible with either light or heavy coke led to the belief that by using small charges 80 placed that. melting would take place in that zone of the cupola where the highest heat and the smallest percentage of oxygen prevailed and by confiningall melting to this zone these losses would be eliminated and the economical use of practically any coke produced for metallurgical purposes would become possible. This widening of the field from whichcoke might be drawn for foundry purposes would serve to place the foundryman in an independent position as regards his source of supply, and would tend to conserve the better grades of coking coals, which are being rapidly exhausted, by making the poorer grades available for mixing with them. In order to investigate conditions within a cupola, the Bureau of Mines as a first step decided to install a commercial cupola, to sample the gases during their travel from the tuy~res upward, and to determine the temperature of the fuel bed.

Jan 1, 1913

By S. D. Bearden

Color enhances expression and communication in all physical objects experienced in life. Pigments provide color and in some applications have a specific additional function. Natural iron oxides are widely distributed throughout the world but only a few deposits are sufficiently pure and possess acceptable color and brightness properties to merit their processing into pigment form. Ochre, the common name for goethite ore, is the best and most under used material in the buff colored pigment market. The geological occurrence of ochre in the basal Shady Formation of the Cartersville Mining District (Georgia) is described. Exploration, processing, and product applications of New Riverside Ochre Company, Inc. are discussed. An overview of the worldwide pigment market is presented with emphasis placed upon the North American activity in iron oxide production and application. The purpose of this paper is to increase the awareness of ochre and its potential market in the colored iron oxide pigment industry, encourage research on the origin of ochre deposits, and stimulate interest in new applications of this unique substance.

Feb 27, 2013

By C. H. Stephenson, Z. White

This paper presents the design approach case study for incorporating a Technogrid® conveyance End-of-wind arresting system within the new South32 Hermosa headframe. Focus is placed on energy absorption requirements, structural integration, and mounting details tailored to the geometry and operational constraints of the headframe. Key considerations include arresting forces, load path continuity, and connection design to ensure reliability and maintainability. The paper also discusses coordination with other headframe systems and the iterative design process used to meet safety standards and client objectives.

Feb 22, 2026

By C. -S. Jiang

In most copper refineries, addition agents are added at predetermined rates with no further monitoring of their activity or concentration in the electrolyte. Increasingly stringent cathode quality requirements, and a desire for better process control in tankhouse operations, have recently directed a number of refineries to search for a better addition agent control strategy. Extensive development work has been carried out at the Noranda Technology Centre for the monitor in of glue and thiourea in copper refinery electrolyte using cyclic voltammetry (cv~. Data from both synthetrc and commercial electrolytes are presented, showing the ability of CV to produce reliable and easily identifiable fingerprints of addition agent concentrations in copper refinery electrolyte.

Jan 1, 1991

By Q Zhou, J Pan, D Q. Zhu, C C. Yang

Oxidised pellets have become an indispensable high-quality charge for blast furnaces (BF) due to their uniform particle size, high iron grade, high mechanical strength, good metallurgical performance, as well as relatively low energy consumption and gaseous pollutant emissions in pellet production. Nevertheless, due to the rapid development of the global steel industry, highquality pellet feeds are becoming more and more scarce. In order to broaden the source of pellet feeds and reduce the production cost of pellets, more and more steel mills are going to use coarse iron ore fines with relatively low iron grade and low impurities for preparation of desirable pellet feeds through a typical wet grinding-settling-filtering process. In this work, the grinding, settling and filtering behaviour of Brazilian and Australian iron ore fines are studied and compared, aiming at finding out the internal relationship between the mineralogical characteristics of different iron ore types and their grinding-settling-filtering performance. The results show that the grindability is heavily dependent on the hardness of iron ores, which is governed by the mineralogical characteristics of the raw materials. Usually the higher the hardness, the more grinding energy is required. Except for Brazilian specularite, Australian hematite-goethite type iron ore fines and Brazilian hematite ore fines exhibit good grindability with a Bond Work Index of about 10–15 kW•h/t. In addition, the settling and filtering performance of ground iron ores are largely affected by the density, mineralogical characteristics of iron ore fines (eg, quantity of clay minerals and goethite and porosity of ore particles), grinding fineness, etc. Generally, iron ore fines with higher density, lower quantity of soft minerals (clay and goethite) and larger particle size give superior settling and filtering performance. For iron ore fines with inferior grinding, settling and filtering performance, applying more energy-efficient grinding techniques, blending with ore types with good settling and filtering performance can reduce grinding energy consumption and improve settling and filtration rates to maximise the productivity of equipment and lower the operational cost

Sep 18, 2023

By V. G. Papangelakis, G. A. Moldoveanu

The use of anhydrite (AH) seed, control of acidity levels and ageing were assessed as means to promote the conversion of freshly produced metastable gypsum generated in-situ to the less soluble anhydrite phase and force deposition of calcium sulphate on seed as opposed to on equipment as scale, while achieving lower terminal aqueous calcium concentration as well. It was found that moderate sulphuric acid levels (0.25M) and ageing in the presence of AH seed accelerated the gypsum-AH conversion, achieving 100% transformation of the metastable gypsum generated in situ to the more stable, less soluble AH in 6-7 days, while lower/nil acidity did not promote more than 30% AH conversion for 10 days, even in the presence of AH seed. These findings indicate that anhydrite seeding, ageing and incomplete neutralization are beneficial for scale control as well as achieving lower calcium levels, thus rendering the resulting solution more amenable for recycling.

Jan 1, 2015

By J. W. Walkiewicz

The Bureau of Mines investigated alloys containing lanthanum (La), praseodymium (Pr), neodymium (Nd), cobalt (Co), copper (Cu), iron (Fe), and magnesium (4g) as possible components of a permanent magnet mate¬rial utilizing a cerium-free synthetic mischmetal (M) as a substitute for scarce samarium (Sm) metal. Magnets containing M-Co-Cu-Mg and M-Co-Cu-Fe-Mg were fabricated by powder metallurgy techniques and evaluated. A synthetic mischmetal (M20) containing 20 pct La, 60 Pr, and 20 Nd yielded the best overall magnetic properties. The M20-Co-Cu-Mg alloys had energy products as high as 13.2 MGOe, remanences as high as 7.89 kG, normal coercivities as high as 6.26 kOe, and intrinsic coercivities as high as 13.4 kOe. The best value of intrinsic coercivity, 22.9 kOe, was obtained with an M-Co-Cu-Mg magnet in which the synthetic misch¬metal contained 30 pct La, 50 Pr, and 20 Nd. These values compare favorably with those of the Sm-Co magnets fabricated and measured at the Bureau's Reno Research Center, which had energy product of 15.1 MGOe, remanence of 7.8 kG, normal coercivity of 7.5 kOe, and intrinsic coercivity of 27.4 kOe. Iron substitution for part of the cobalt resulted in a decrease of magnetic properties, although several percent iron can be added before a drastic loss of magnetic properties occurs.

Jan 1, 1983