Search Documents

By Northeastern University, B. Y. Cui, B. Y. Wang, D. Z. Wei, W. G. Liu, Z. C. Guan, S. L. Gao

To recover iron values from low grade ores by reverse froth flotation method, further research on cationic collectors used in reverse flotation of iron ores is launched to promote the utilization efficiency of iron ores. In this paper, one new cationic surfactant, bis(2-hydroxylethyl) dodecylamine (BHD), that could be dissolved in water easily was used as collector for quartz flotation. Flotation results indicated that BHD shows stronger collecting performance on quartz than hematite. The maximum recovery of 96.30% to quartz is obtained at a collector concentration of 20.0 mg/L in the pulp pH range from 5 to 7. This collector can be used to float quartz from hematite. And optimal separation results with 86.59% iron recovery and 66.60% iron grade to synthetic sample were achieved at a collector concentration of 20.0 mg/L and pulp pH of 5.02 when hematite and quartz were mixed at a mass ratio of 3:2. The adsorption mechanism of the collector on quartz surface was investigated by XPS analysis, infrared spectroscopic analysis and zeta-potential measurements, which revealed that electrostatic attraction and hydrogen bonding adsorption occur between collector and quartz surface.

Jan 1, 2016

By Dennis A. Hansen

As part of a U.S. Bureau of Mines program to develop a more continuous titanium metal extraction process that uses domestic resources, a study was made to determine the extraction of titanium (Ti) and iron (Fe) from New York rock ilmenite using fluosilicic acid (H2SiF6). The effects of leach temperature, acid concentration, and particle size were investigated for the rate at which Ti and Fe are extracted from the ilmenite. Within the leach time studied, the extraction data fit a shrinking-core model; the rate-controlling step was diffusion of H2SiF6 through an ash layer resulting from a heterogeneous leaching reaction. The rate is linearly dependent on the H2SiF6 concentration and is inversely proportional to the square of the particle diameter. Using 2.6M H2SiF6 at 85°C, 49% of the Ti and 53% of the Fe in 44-to 74-µm New York rock ilmenite were extracted in 3 h.

Jan 1, 2010

By Fabio Santillan, Lyndon Bedford

"This paper presents the main features of the Wolf Creek Dam Foundation Remediation Project, highlighting the innovative construction approach and stressing on how the collaboration between the contractor and the owner became a key element for the success of this project.The main rehabilitation contract, $341 M, was awarded in 2008 for the construction of a 980,000 sqft concrete barrier. Most of this 2ft-wide concrete barrier wall is being built to depths reaching 277 ft using innovative construction techniques proposed by the contractor and under quality control measures that exceed by far the industry standards.The construction of the barrier wall entails the use of nine different foundation techniques which run concurrently following very stringent requirements in terms of verticality, distance between open elements, strength, permeability and dimensions that control the installation sequence of each barrier wall element.The innovative construction approach by the contractor and the collaborative efforts by the contractor and the USACE (“US Army Corps of Engineers”) have brought this unique and very difficult project to a successful completion, setting new standards in the dam foundation industry and nine months ahead of scheduleINTRODUCTIONWolf Creek Dam is on the Cumberland River in south central Kentucky. It provides hydropower, flood control, water supply, and water quality benefits for the Cumberland River system and surrounding region. The lake is a source of recreation that has attracted more visitors (4.89 million) than Yellowstone National Park (2.87 million).The dam and its adjacent reservoir reside upon a heavily Karst bedrock foundation. In late January 2007, the USACE placed the dam under a 'high risk' for failure designation. As a temporary measure, the pool elevation was lowered to 680 ft Above Main Sea Level (“AMSL”), 80 ft below its maximum capacity, with huge impacts to the local economy while the major, and ambitious, $ 594 million remediation program to bring the dam back to its full operating condition was carried out.The main rehabilitation contract of $341 million was awarded in 2008 for the construction of a 980,000 sqft concrete cut-off barrier. Most of this 2ft-wide concrete barrier wall has been built to depths reaching 277 ft using innovative construction techniques under quality control measures that far exceed the industry standards."

Jan 1, 2015

By Montaser S. El‑Salmawy, AHMED A. S. SEIFELNASSR, Ahmed Al‑Abady, Abdeaziem M. Abdelaal, Amr F. M. Ibrahim

Iron is a key detrimental impurity in silica sands that determines their contribution to high-technology industries. Herein, a simple ecologically sound approach is investigated for iron removal from a silica sand sample obtained from the El-Zaafarana area-Egypt. The sample was subjected to a detailed microscopic mineralogical study supported by XRD and XRF characterization. The sample was beneficiated using distilled water attrition scrubbing and screening over a 25 μm sieve followed by leaching using a mixture of equal amounts of phosphoric and oxalic acids. Leaching experiments were designed and analyzed using the Box-Behnken design (BBD) methodology. A model was developed and evaluated using the analysis of variance technique to map the relationship between the residual iron oxide in the produced concentrate and selected variables such as leaching temperature, oxalic acid, and phosphoric acid concentrations. XRD and mineralogical analysis reveal that quartz is the most dominant constituent of the studied sand and other minerals such as kaolinite, iron oxide, rutile, and zircon exist in trace amounts. The head sample shows a silica and iron oxide content of 95.69% and 2379 ppm, respectively. Attrition and separation over a 25 μm sieve increase the silica content to 97.05% and decreases the residual iron oxide to 455 ppm. The final product after leaching under optimized conditions shows 99.82% silica and 55 ppm iron oxide.

Aug 30, 2022

By R. R. Bhappu

The metallurgical processing industry is in the midst of a hydrometallurgical revolution with mining companies looking for low cost, energy efficient and environmentally friendly technologies for processing sulfide ores and concentrates. The Intec Copper Process is one of the most advanced of these technologies and has the potential to greatly change the way copper concentrates are treated in the future. Specifically, the Intec process has the ability to be built on a small scale and at mine sites while being much more economic than conventional smelting. Intec Copper has constructed a I tonne of copper per day demonstration plant in Sydney, Australia designed to verify metallurgical and operational performance. This paper will describe the process in more detail and provide preliminary results of the process based on the plant's performance. It will also compare the Intec Copper Process with a few of the competing technologies and evaluate the relative economic merits of Intec.

Jan 1, 1999

By David Hartley

United States Steel Corporation Minntac Mine is located at Mt. Iron, Minnesota, on the Mesabi Iron Range. The taconite pit is two miles long by a mile wide, with a maximum depth of 170 feet. This paper will deal with the radio remote control of locomotives engaged in the railroad haulage of crude ore and waste rock at this property.

Jan 1, 1970

In the past few years the Rietveld method emerged as a routine tool for quantitative phase analysis (QPA) from X-ray diffraction data. Fast and reliable results became possible by combining modern computer technology and optimised mathematical algorithms with the fundamental parameters approach in the Bruker AXS TOPAS software. Here the routine analysis of bauxite raw material and of aluminium bath electrolyte is presented. The accuracy of bauxite quantification was tested by analysing the IUCr round robin sample. An agreement of better than one per cent was obtained for minor constituents and a maximum deviation of 2.5 per cent for the major phases. This is excellent agreement with expected results from weighting. Ten different phases were quantified in natural samples from Turkey with a precision better 0.5 per cent for the major phases and one per cent for the minor phases. Additionally, crystallite sizes were obtained from the peak profiles that give valuable information for the processability of the material. XRD data from solidified aluminium electrolytes were rapidly measured using silicon strip detector technology. With the LynxEyeTM detector full patterns were collected in 90 seconds and analysed with TOPAS. It is shown how to derive well-established measures such as bath ratio and excess AlF3 from the Rietveld results. These measures are widely used in aluminium production and readily available with very high precision. The excellent agreement with ALCAN reference data demonstrates the outstanding accuracy of the method. The mean deviation between here presented results and reference data is below 0.5 per cent for total CaF2, below 0.25 per cent for excess AlF3 and 0.02 for the bath ratio. The precision of the method was evaluated by repeated measurements.

Jan 1, 2008

By Alfred L. Ransome

The plan to develop a standard system of names and definitions of regions and districts in Alaska was borne of the need for a tool to use in statistical and economic studies of the mineral industry of the Territory. The purpose of this report is to present to the mineral industry, and to those individuals interested in the mineral or allied industries in Alaska, the system used by the Bureau of Mines in connection with its legal function of collecting and disseminating mineral statistics. It is hoped that the specific descriptions given will result in a more complete understanding of what is meant by the regional and district names that appear in publications of the Bureau of Mines relative to the mineral industry of the Territory. Problem of Standardization of Names and Definitions The question might be asked, does the naming and defining of regions and districts in Alaska present a problem relative to the establishment of a standard? Is it necessary to establish a standard?

Jan 1, 1954

By Todd Wanless

This paper addresses the challenges experienced by the designer and three government agencies during implementation of major improvements for the Turkey Creek Tunnel in Kansas City, Kansas. The tunnel serves as a vital stormwater conveyance system for upstream flood control. Major structural deficiencies were identified within the tunnel including complete loss of sidewall and invert. Without immediate attention, complete loss of the tunnel arch could lead to blockage and extensive remedial repairs under difficult conditions. Considering that tunnel flows must be maintained during construction, a phased design and construction process has been implemented to expedite stabilization of the erosion cavities followed by tunnel liner repairs.

Jan 1, 2008

By Michael Windhager

UltimaTM rolls have been designed for intermediate and finishing stands of rod and bar and small and medium section mills. The rolls and rings are spun cast, with a highly alloyed working layer and a tough nodular iron core. Microstructure and hardness level can be adjusted over a wide range, which allows us to adapt the rolls to differing rolling conditions. After introducing the UltimaTM concept, this paper will describe the results of UltimaTM rolls achieved in various mill applications, like finish rolling of rebar, and slitting. Special emphasis is given to performance gains when using UltimaTM rolls, compared to standard rolls. This paper also examines the impact of UltimaTM rolls on mill and roll shop productivity.

Jul 30, 2018

By James E. Hoffmann

This paper briefly reviews the conventional technologies employed for the treatment of copper refinery electrolyte bleed. The strength and weaknesses of conventional practice will be reviewed and a number of process options to address the weaknesses of present process technology will be described and evaluated. The effect of process selection upon energy consumption and the environmental aspects of process effluent control will be discussed.

Jan 1, 1997

By R. Thierbach, W. Kahnt, Oberthür. T., D. Eisenburger, V. Gundelach

ABSTRACT: The ground penetrating radar (GPR) method was used in a platinum mine in Zimbabwe by members of the Federal Institute for Geosciences and Mineral Resources (BGR). The measurements were carried out in boreholes and drifts. Electromagnetic re?ections from a fault that consistently trends parallel to the mineralization zone permitted the mapping of the economically minable parts of the deposit. An introduction is given to the geology of the studied area and the application of the GPR method. The electrical parametres of the rocks are measured in situ, the GPR measurements are displayed with radargrams, and the visible structures are explained in illustrations.

Jan 1, 2010

By ROBERT H. BOOTH

THE happy intra-plant relationships of the Bridgeport Brass Co. are largely attributable to the interest of the management in this important business factor. In furtherance of this development Carl F. Dietz, President of the Company and a member of the Institute, has contributed the novel plan for the objective presentation of business economics, described herein. All of the officers of the corporation are active in its management and they together with many other workers filling both executive and subordinate positions have a substantial financial interest in the enterprise. The viewpoint of this organization is fairly reflected by the following quotation from Roosevelt's "The Foes of Our Own Household."

Jan 1, 1924

By J. V. Batty

The Bureau of Mines devised techniques involving the use of beta-and gamma-ray-emitting radioisotopes and successfully adapted these techniques to the density of mineralized flotation froths) the rate of flow of finely ground ore pulps) and the residence time of pulps in processing circuits. Specifically, the water and mineral loads of flotation froths were continuously measured by determining the proportion of a constant-strength beam of beta rays that was absorbed by the froth column. Continuous measurement of the rate of flow of an ore pulp was accomplished by measuring the changing width of a free-falling stream of the pulp with a collimated beam of beta rays. The residence time of solids in conditioning and resin-in-pulp circuits was accurately measured by following the progress through these circuits of a portion of the pulp that had been tagged with the gamma-emitting Ag110 radioisotope.

Jan 1, 1966

By R. E. Nivens

In the past, Newmont Gold Company relied on cement for their ore agglomeration process. With assistance from Betz Industrial, Newmont began Investigating the use of polymers for ore agglomeration. If gold recovery would not be jeopardized, then polymers could replace cement and possibly reduce operational costs associated with cement agglomeration. The following outlines the preliminary testing conducted to determine the feasibility of polymer agglomeration with Newmont's ore and the results of the test heap, which was constructed so the program could be examined under actual operating conditions. Similar polymer agglomeration testing has been successfully performed in other Nevada gold operations. By eliminating the need for cement, a polymeric agglomeration program could improve material handling operations, as well as offer the following additional savings. First, the polymer application uses only lime for adjusting basicity, the polymer does not contribute any alkalinity to the heap. Because lime is more soluble than cement, detoxification of the heap becomes much faster and less costly for the mine relative to rinsing cement alkalinity. The following graph compares the detoxification rate of cement and polymer over a 33 day cycle.

Jan 1, 1993

By L. E. Snow, L. F. Pett

AT the Utah Copper Pit of Kennecott Copper Corp. a versatile mobile drill unit has been developed and tested. Through increased drilling speed and additional available drilling time, an improvement of 233 pct in drill performance has been realized. Operators using drill power can quickly and easily convert the unit from a vertical to a toe hole drill. Drilling is done with the machine in line with the unit or at right angles to it. Table I covers the 1950 drill record at the mine, showing the types of machines used and the footage obtained. Development of the new units was prompted by a desire for solution of the following problems: 1—The ever-expanding operations within the Utah Pit, requiring some 65 miles of transmission pipe lines radiating from a central compressed air plant, have now taxed this compressor plant beyond capacity. While 100 lb per sq in. pressure is maintained at compressors, transmission losses from innumerable small leaks result in low terminal pressure at the drills. Fig. 1 illustrates that while terminal pressure varies according to size of air hose and fittings used, the average drill is operating on air pressures within the 60 to 70-lb range. The compressor plant is operated primarily for air rock drills. All drilling is done on day shift, but it is necessary to run two of the three 3720 cu ft capacity compressors during night shift in order to prevent drastic loss of pressure through leaks. On day shift all three compressor units are operated at capacity, so that there is no reserve safeguard available for extensive repairs to any compressor. The calculated volume of compressed air required for operation of 25 drills is but 33 pct of three day-shift compressors. While compressed air is being used to a minor extent for purposes other than drilling, it is felt that satisfactory substitute facilities could be pro- vided in the event that air lines were no longer available. 2—Drill performance has increased beyond the capacity of present 3-in. drifter machines. 3—The installation, maintenance, and moving of air lines in routine mining is a growing problem. The 2-in. level lines are placed outside electrification towers and must be moved to new location upon completion of each shovel cut. In addition to these moves it is often necessary to dismantle level lines so that excessive shovel spillage, or material covering track following a blast, can be pushed in the clear with bulldozers. Where level room is limited, it is often necessary to remove air lines in giving bulldozers room to prepare grades for wagon drills. In spite of precautions taken, many level lines become buried, twisted, and constricted, with excessive air loss resulting. Excessive back break in blasting often leaves several sections of air line suspended in mid-air. Occasionally air lines come in contact with defective electric transmission towers, so that holes are burned through pipe. 4—Rail-handling of drilling equipment such as wagon drills from one location to another requires considerable locomotive crane crew time. Any new unit developed should travel under its own power. 5—Present practice requires accessory material including hose, water pressure tanks, water barrels, drill steel, and bits to be transported by means of push cars when drill locations are changed on any level. 6—In order to supply numerous drill locations with material, many stock piles of new drill rods, drill bits, and other essentials must be left at strategic points, usually in the vicinity of powder magazines. This practice makes for poor housekeeping and contributes to the loss of supplies. Planning the Unit It was felt that a mobile drill unit which would rectify the foregoing problems should meet certain demands: 1—It must furnish compressed air to operate a 4-in. rock drill at a pressure of 90 to 100 lb.

Jan 1, 1953

By L. E. Snow, L. F. Pett

AT the Utah Copper Pit of Kennecott Copper Corp. a versatile mobile drill unit has been developed and tested. Through increased drilling speed and additional available drilling time, an improvement of 233 pct in drill performance has been realized. Operators using drill power can quickly and easily convert the unit from a vertical to a toe hole drill. Drilling is done with the machine in line with the unit or at right angles to it. Table I covers the 1950 drill record at the mine, showing the types of machines used and the footage obtained. Development of the new units was prompted by a desire for solution of the following problems: 1—The ever-expanding operations within the Utah Pit, requiring some 65 miles of transmission pipe lines radiating from a central compressed air plant, have now taxed this compressor plant beyond capacity. While 100 lb per sq in. pressure is maintained at compressors, transmission losses from innumerable small leaks result in low terminal pressure at the drills. Fig. 1 illustrates that while terminal pressure varies according to size of air hose and fittings used, the average drill is operating on air pressures within the 60 to 70-lb range. The compressor plant is operated primarily for air rock drills. All drilling is done on day shift, but it is necessary to run two of the three 3720 cu ft capacity compressors during night shift in order to prevent drastic loss of pressure through leaks. On day shift all three compressor units are operated at capacity, so that there is no reserve safeguard available for extensive repairs to any compressor. The calculated volume of compressed air required for operation of 25 drills is but 33 pct of three day-shift compressors. While compressed air is being used to a minor extent for purposes other than drilling, it is felt that satisfactory substitute facilities could be pro- vided in the event that air lines were no longer available. 2—Drill performance has increased beyond the capacity of present 3-in. drifter machines. 3—The installation, maintenance, and moving of air lines in routine mining is a growing problem. The 2-in. level lines are placed outside electrification towers and must be moved to new location upon completion of each shovel cut. In addition to these moves it is often necessary to dismantle level lines so that excessive shovel spillage, or material covering track following a blast, can be pushed in the clear with bulldozers. Where level room is limited, it is often necessary to remove air lines in giving bulldozers room to prepare grades for wagon drills. In spite of precautions taken, many level lines become buried, twisted, and constricted, with excessive air loss resulting. Excessive back break in blasting often leaves several sections of air line suspended in mid-air. Occasionally air lines come in contact with defective electric transmission towers, so that holes are burned through pipe. 4—Rail-handling of drilling equipment such as wagon drills from one location to another requires considerable locomotive crane crew time. Any new unit developed should travel under its own power. 5—Present practice requires accessory material including hose, water pressure tanks, water barrels, drill steel, and bits to be transported by means of push cars when drill locations are changed on any level. 6—In order to supply numerous drill locations with material, many stock piles of new drill rods, drill bits, and other essentials must be left at strategic points, usually in the vicinity of powder magazines. This practice makes for poor housekeeping and contributes to the loss of supplies. Planning the Unit It was felt that a mobile drill unit which would rectify the foregoing problems should meet certain demands: 1—It must furnish compressed air to operate a 4-in. rock drill at a pressure of 90 to 100 lb.

Jan 1, 1953

By S. C. Schaefer

Thermodynamic properties of indium oxide (In203) have been studied with a high-temperature galvanic cell employing stabilized zirconia electrolytes. In the temperature range 790° to 1,230° K the free-energy change for the cell reaction 21n(1) + 3Cu20(c) = In203(c) + 6Cu(c) together with the standard free energy of formation of cuprous oxide gives the standard free energy of formation of indium oxide from the elements as ?Gf° = -218.78 + 75.34 X 10-3T ±0.7 kcal/mole. A third-law analysis yields the standard enthalpy of formation: ?Hf°298.15 = -221.5 kcal/mole.

Jan 1, 1971

By Don Rapp, Rufus Flinchum

Air blast and flyrock are two of the most critical concerns facing the blaster of today. This paper will provide the blaster with proven procedures for recognizing open face and bench surface problems, explain various surveying methods, and provide the mathematical formulas for calculating and designing proper hole placement and explosive load configuration. A concept called "Pattern Footage" is utilized in conjunction with a USBM study to develop blast designs aimed at minimizing air blast and flyrock. In addition to this main focus, this concept can be used in shot displacement and cast blasting design.

Jan 1, 1993

By John Greenhalgh, Benoit De Rivaz

"1.INTRODUCTIONThis paper is based on the Lee Tunnel project, which is part of the Thames Water’s Tideway Project.The client Thames Water has employed a Joint Venture of Morgan Sindall/Vinci Grand Projets and Bachy Soletanche to undertake the design and construction of the project under the management of CH2M Hill at a value in excess of £635 million ($990 million). The 3 main elements of the tunnel project are the permanent lining to the shafts, the precast segmental lining, and the secondary tunnel lining. All 3 are reinforced with different types of Dramix steel wire fibers and each element will be described in this paper. This paper will explain the basic structural design of FRC (Fiber reinforced concrete) based on the post cracking residual strength and will describe all the steps of this project, the testing program realized to support innovative design and the main technical learning point. 2.BASIC CONCEPT OF STRUCTURAL DESIGN OF FRCStructural design of FRC elements is based on the post-cracking residual strength provided by fiberreinforcement. Other cases, like early age crack-control or fire resistance, are considered non-structural use of FRC. For structural use, a minimum mechanical performance of FRC must be guaranteed. Fibers can be used to improve the behavior at SLS (Service Limit State) since they can reduce crack spacing and crack width, thereby improving durability and they can be used to improve the behavior at ULS (Ultimate Limit State) where they can partially or totally substitute conventional reinforcement in most conditions. In the design process, the definition of the performance expected from the material is a key factor and the mix-design of the material has to be optimized for the required structural performance.2.1 Testing Method In order to ascertain the structural requirements requested for the FRC segments, preliminary testing on samples will be required and the effectiveness of the proposed solution will also be assured by the testing of full scale specimens. Structural design of FRC elements is based on the post-cracking residual strength provided by fiber reinforcement. For structural use, a minimum mechanical performance of FRC must be guaranteed. Nominal values of the material properties can be determined by performing a 3-point bending test on a notched beam according to EN14651 (figure 1) or by performing the ASTM C1609 beam test:"

Jan 1, 2016