Search Documents

By R. D. Cook, J. L. Johnson

"Measuring mud bed level in a sedimentation device is an important control variable. Methods used to date for this purpose have had limited success providing continuous, consistent measurements at a reasonable price. This paper describes a new instrument for detecting the mud bed / liquor interface as well as bed density profiles. The state of the bed is measured directly with sensors located in the thickener. Data from bench-scale and full-scale tests show that the bed level is well defined and easily detected. In addition, full-scale testing revealed unprecedented information about thickener beds. Variation in bed density gave new insight into thickener bed dynamics, providing design and control opportunities never before possible. This novel instrument can significantly improve thickener control by providing reliable and consistent bed level measurements. It is also capable of measuring bed density profiles that can potentially identify significant operating problems early enough to take corrective action before experiencing costly shut downs. INTRODUCTION Numerous studies and papers have been devoted to the subject of thickener design and operation to achieve specified throughput and discharge densities. Mathematical models have been developed that present methods for sizing thickeners and predicting performance under varying process conditions. The compression effect of deeper beds on dewatering performance is a recognized phenomenon (Wilhelm and Naide 1981). This is one variable of many that are inter-related and influence thickener performance. For example in the steady-state, continuous operation of a thickener, if the solids feed rate increases and the bed level remains the same, the underflow discharge rate must increase with the result of solids concentration being lower. The interactions of these parameters are at the heart of thickener models. One such model (Burger and Narvaez 2007), predicts solids concentration profiles increasing downward and discontinuities between settling zones. This model uses sediment height (bed level) as a parameter that influences capacity calculations to achieve the specified solids concentration of the underflow. Knowing the bed depth is critical to maintaining stable thickener operation. Implicit in these modeling strategies are some basic assumptions such as homogeneous distribution of solids in the different settling zones, plug flow of solids through the settling zones and steady state operation of the thickener. The accuracy of these assumptions has not been verified because there has been little visibility inside the bed of full size operating thickeners. Testing of the instrument presented in this paper demonstrates that it provides a degree of visibility of the dynamics in a thickener not previously possible and indicates that the basic assumptions of the modeling strategies may not be completely accurate."

Jan 1, 2015

By R. W. Brigstocke

History The birth of the mining industry of Canada took place about 1670. According to Salone (Salone E., La Colonisation de la Nouvelle France, page 205) the first discovery of ore in the country was made by an iron-master, Monsieur de la Potardiere, near Trois Rivieres, Quebec. Under French rule some prospecting was done; but at this time no one seemed to consider the working of mines practicable. It was not until the time that Begon became Intendant, when the Marquis of Vaudreuil was Governor, that mining was attempted. Begon was a patron of industrial arts and did his best to promote home manufactures. The mining industry was developed under his regime and discoveries of copper and lead ores were made in 1730. About this time the St. Maurice Forges were erected to treat bog-iron ore, and they were in operation for many years. Prior to 1747, iron pans to the value of £21,000 were manufactured, together with bar-iron and plough-shares. About 1769, that is, ten years after the conquest by Wolfe, stoves and other articles, and, later, potash kettles, appeared. What is still more interesting to us-or was, at least, to General Wolfe-is that cannon balls made at the St. Maurice Forges delayed his operations. A map dated 1744, a copy of which appears in the report of the Ontario Bureau of Mines for 1913 (Vol. XIX), indicates the extensiveness of the wanderings of the French and also shows the location of the lead mine on the east shore of Lake Timiskaming. Bog-iron ore was turned into metal, with charcoal for fuel, at Norman-dale, Norfolk county, Ontario, in 1813, and at Clementsport, Nova Scotia, in 1825. In a volume published in 1672, reference is made to the occurrence of coal on the Atlantic seaboard, and in 1677 Monsieur Duchesneau, the Intendant, levied a royalty of twenty sous per ton on all coal taken from Cape Breton.

Jan 1, 1932

By M. Polat

Variations in flotation rate by particle size and specific gravity have been investigated for three different bituminous coals. The flotation rates for various components were determined by separating the products of bulk flotation into size-specific gravity fractions. The effects of feed size and reagent addition on the flotation response of individual size-specific gravity fractions were evaluated.

Jan 1, 1994

By G. E. Geiger

The purpose of this research was to develop a computer simulator fur predicting the air quality in existing coal mines as well as a design aid for developing new mines. In addition to the air quantity flow, the other variables of tempera Lure, moisture, methane and respirable dust are necessary to determine the air quality. An additional feature of this simulator is that it allows parametric studies of these variables to explore the effect that these variables have on the air quality of an operating mine system. The research has also pointed out arias where more research is needed, and promote better and more systematic data taking techniques. Wang and Hartman (see Reference 9, on page 1-98 of Section 1) had already published a computer program to determine the ventilation of large mines, and Wang and Saperstein (see Reference 10 on page 1-98 of Section 1) later published a refinement of the work in the previous reference. These references were the starting point of the simulator developed by this present research effort, and Section 1 of this report is a slightly modified version of the original vent elation program. The modifications were necessary to permit the additional programs of temperature-moisture, methane and dust to be

Jan 1, 1972

By K Ehrig, V Liebezeit, E Macmillan

The results from metallurgical test programs are used in feasibility studies for design of new plants and brownfield expansions, in long term mine plans, and to make decisions in an operating plant. There are many elements which contribute to a well-constructed test work program. Ultimately, understanding the accuracy and precision of the test work results is critical to ensuring good decision-making at various phases of a project.Every resource drilling and associated assaying program will have a quality assurance / quality control (QA/QC) component, however this often seems to be overlooked in metallurgical testing programs. The principles of “international standard” or “certified reference material” samples and replicate/duplicate testing can be applied to metallurgical programs, although there are metallurgical-specific considerations in both generating and analysing the data.This paper will describe the QA/QC program carried out within the Olympic Dam geometallurgy program. It will present results in the form of case studies from ten years of testing of replicates and bulk reference samples for industry-standard comminution tests as well as laboratory flotation and leaching tests. The Olympic Dam geometallurgy quality control program has enabled quantification of the precision of metallurgical testing and improved our understanding of the best possible modelling results given the underlying dataCITATION:Ehrig, K, Liebezeit, V and Macmillan, E, 2017. Metallurgical QA/QC – who needs it? The Olympic Dam experience, in Proceedings MetPlant 2017, pp 31–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By George C. Stone

WHEN George C. Stone, a Director of the Institute, and so well known to our Members in connection with the Institute's many activities was abroad in 1.919, he secured an interesting collection of these coins, which appeared in Zinc, a publication by the New Jersey Zinc Co. Regarding this collection of coin, Mr. Stone says: "During the war, all gold and most of the silver disappeared, making small change very scarce. As the French Government was fully occupied by the war, it allowed various Chambers of Commerce and other bodies to issue money, both paper and coins. Many of the latter were made of zinc, and I secured several while in Paris. We had all heard of the Belgian and German zinc coins, but I imagine few knew how many different kinds there were. The accompanying plates show both sides of those I got. I took all that the dealer had; but he said that there were a number of others in existence. The coins in the bottom line were issued by the Germans in Belgium during the war and all are still in common use. The first two in the next to the bottom line are German. All of the others were issued by Chambers of Commerce or corporations. A few have been nickel plated; these look and wear much better than the others. "Coins" made of pasteboard were also issued by similar bodies, also notes.

Jan 1, 1920

By T. Tomioka

1. An Overall View of the Japanese Ferroalloys Industry 1) Depressed Demand for Ferroalloys: In Japan consumption of ferroalloys in the last ten years has decreased, although there has been some fluctuation from year to year. During this term production figures of the steel industry, which are closely related to consumption of ferroalloys, are as follows: Shipment of steel products for the domestic market has declined gradually from 69 million tons in 1979, which was the peak year for steel production, to 60.3 million tons in 1982 and 60.4 million tons in 1983, the level of 1978. In addition, exports also have been a downward trend since 1976, which was the peak year with tonnage of 34 million tons, to 28 million tons in 1982 and 31 million tons in 1983.

Jan 1, 1984

By J. W. Paul

Withdrawing timber in coal mines is done for the purpose of inducing the roof to cave in the mined-out areas and thereby relieve stresses in the immediate roof material over the working places adjacent to the breakline of the roof, thus preventing the crushing of the ends of pillars and adding to the safety of those engaged in pillar extraction. A secondary purpose is the recovery of timber for further use either as prop-, crossbars, lagging, sprags or cap pieces. At some mines timber is withdrawn as a precaution against fire which may he of spontaneous origin, because wood always aids a fire of any origin. With some of the power-driven types of machines now in use a greater proportion of mine timber may be recovered, and in mines where pillars are left too narrow for their removal some of the timber in rooms might be salvaged for further use.

Jan 1, 1933

Universities have had a long history in the education of geology graduates, Analysis of this history reveals a record of success, as judged on a world basis. However there have been significant changes in the last 20 years that have impacted on the ability of universities to continue to provide their traditional style of geology education. These changes have increased in the last 10 years. In the teaching side, there has been a change in expectations. Additionally the increasing workload decreases the value of each academic to perform the tasks needed by the new education. In the area of research, the funds provided have continued to decline, in both real and absolute terms, and it is now necessary for universities to seek out funds to pay for their postgraduate research. Additionally, the universities have slipped into the error of what cahn only be termed "academic incest", and research student mobility has decreased to an undesirable level, stifling initiative and new ideas in a number of cases, The only solution is for Government monies to be "directed" - ie that the postgraduate student must leave his or her original university in order to receifve the research stipend/scholarship. On the government front, the government and its agencies have not adequately analysed and recognised the need for the redirection of education and research funds into the needy areas of science and technology, especially those that related to the minerals area.

Jan 1, 1986

By V. Hudecek

Problems of sudden outbursts of rock and gas present in deep mine mining ones of the most complicated interrogation. It is searching for the methods of prediction and prognosis that can be most useful for the government of these phenomena. Till now the pressure and the desorption of gas in bore holes was consider to be the decisive criteria. By the work of authors with using of statistical date was verify that for considerable reliability of forecast and prevent outbursts is necessity investigate characteristics of workplace and other indicators. These indicators were analyzing and assemblage into mathematical dependences which represent active and passive force asserting with in the process of rush. It was validated by using the equations which are presented in the manuscript that the accuracy of pre-diction of the phenomena is higher and methods of preventions are better also.

Jan 1, 2014

By T. T. Campbell

This report traces the development of techniques for the preparation of high-purity rare-earth metals. Rare-earth metals, excepting samarium, europium, and ytterbium, were prepared by converting their oxides to anhydrous chlorides or fluorides and reducing the rare-earth halides with active metals such as lithium or calcium. High-purity, anhydrous rare-earth chlorides were prepared by dissolving the rare-earth oxides in hydrochloric acid to form hydrated chlorides and by subsequently dehydrating the hydrated salts in the presence of ammonium chloride at temperatures ranging from 70° to 360° C. while under reduced pressure (50 microns to 1 inch Hg). The chlorides were also prepared by direct chlorination of rare-earth oxide-carbon mixtures. Reaction efficiencies in excess of 95 percent were obtained by either method; however, purer chlorides were prepared by the aqueous ammonium chloride conversion method. Purification of yttrium chloride by high-temperature vacuum distillation proved to be an effective method of separating, oxygen-bearing compounds from the chloride. Yttrium metal prepared from purified chloride contained significantly smaller amounts of oxygen (990 p.p.m. oxygen in yttrium metal prepared from raw chloride and 200 p.p.m. in that prepared from distilled chloride).

Jan 1, 1961

By Roberto Folchi, Hans Wallin, Mara Battocchio

An understanding of explosives science and technology, and the competence to harness it is central to maintaining Explosives capability, national security, and in sustaining a competitive industry. A consequence of eroding this competence is the increased likelihood of explosives accidents. These are often catastrophic as demonstrated by accidents in Nigeria, Russia, Toulouse and Enschede. In addition to the serious loss of life there was the very significant damage to houses, domestic and industrial infrastructure and to the environment at a cost of many millions of Euros.

Jan 1, 2013

By V. Kecojevic

The objective of this research was to establish the relationship between production, consumption and energy cost in the surface mining of bituminous coal. Specific energy sources such as diesel, gasoline, electricity, explosives and bituminous coal were considered in this study. Gain in net energy, proportion of the cost of energy consumption and total energy cost relative to total revenue of extracted coal were determined, and a new energy efficiency index and a new energy-cost ratio were established. A case study on an operating surface coal mine was carried out to demonstrate the application of the newly developed method. The results of this study can be used by the mine operators in establishing strategies for the optimization of energy production and consumption, and for reducing the cost of bituminous coal extraction.

Jan 1, 2014

By N Rivera, A Music, C Cisternas

In an underground mine operated with panel caving and subjected to high stresses, geotechnical events such as collapses or rock bursts are fairly recurrent. Both situations can involve risks for people, considerable production losses and increasing operational costs.This paper discusses an operational methodology for the recovery of the undercutting front carried out at El Teniente mine, which uses panel cave mining with post-undercutting, after the occurrence of severe damage due to a seismic cluster. The main objective of the recovery of the undercutting front is to prevent the spread of the collapse to the production level, risking the operational continuity. The methodology is the result of repairs that were carried out in the year 2014 at the North Reserves sector from El Teniente mine. Its characteristics are an undercutting front of almost 1000 m long, with the presence of relevant structures and faults, high stresses and high seismic activity.The practical implementation of the proposed methodology was successful since it prevented the spread of the damage, completely recovered the undercutting front and avoided production losses during the execution of the repairs. Also, considering the origin of the damage and the operations associated to the subsequent recovery of the undercutting front, in this paper we discuss the main control variables to be measured. These variables should allow any operator and short-term planner to take action in mines operated with conventional panel caving in a complex geotechnical environment.CITATION:Rivera, N, Music, A and Cisternas, C, 2016. Recovery of the undercutting front in a mine with conventional panel caving – case study at North Reserves sector, El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 713–722 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By R Berry, J Lett, C L. Harraden

"In the past decade, increased processing capacity combined with precision robotics in high resolution spectrometers has resulted in a new generation of high-speed hyperspectral core logging systems. The application of these multisensor automated platforms provides a key advancement in the characterisation of metal resources. The development of this technology has allowed for comprehensive, drill core-based, mine-scale rock mass characterisation studies. Here we propose a new method for the extraction of parameters that seek to more accurately quantify ground conditions, including quantified rock mass rating (RMR) and the Rock Tunnelling Quality (Q) Index. Data inputs include rock quality designation (RQD), number of joint sets, joint roughness, joint alteration and joint spacing. Geologists and geotechnical engineers have historically collected these inputs by manually logging drill core. With automated core scanning technologies, these parameters can be estimated from the acquired image data and used to objectively calculate RMR and Q-index values for oriented core.Corescan is an automated hyperspectral core scanner that uses a 3D laser profiling system to measure the height of the surface of drill core. This technology allows for rapid core analysis to produce detailed fracture and rock condition data. Through an integrated geometallurgical approach, the proposed methodology will test the accuracy of joint measurement using the height profile Corescan data from oriented drill core. This will be combined with joint roughness and alteration mineralogy measured from the hyperspectral images to calculate the RMR and the Q-index continuously downhole. The values obtained can then be compared to the traditional, manual geotechnical log data. If the precision is sufficient, these techniques can then be applied site-wide to automate the collection and modelling of key ground condition classification indices across an entire deposit. Compared to the laborious manual geotechnical logging procedures that currently form the industry standard, utilisation of core laser profile data and high resolution red-green-blue (RGB) images provide an opportunity to collect large volumes of consistent geotechnical data, which can increase the efficiency and accuracy of deposit scale geotechnical models.CITATION:Harraden, C L, Berry, R and Lett, J, 2016. Proposed Methodology for Utilising Automated Core Logging Technology to Extract Geotechnical Index Parameters, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 119–124 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By A. Plugatyr, C. P. Baxter

"Bessemer matte iron content is a critical process parameter that needs to be closely monitored and controlled in order to achieve optimal Ni/Cu smelter returns. Current process control practices during Ni/Cu converting often rely on visual observations and typically involve matte sampling to confirm that target composition was reached. A high-level techno-economic analysis study was carried out to evaluate potential direct benefits of advanced process control during the final stages of Ni/Cu matte converting. The results indicate that the magnitude of direct benefits will largely depend on matte iron control practices already implemented as well as matte iron set point. Preliminary assessment suggests that under the assumptions used in this study, implementation of advanced process control can potentially result in additional revenues ranging from several hundreds of thousands to tens of millions of US dollars per year per converter producing about 200 tonnes of Bessemer matte per day based on Ni, Cu, and Co metal recoveries alone.INTRODUCTION Real-time measurement of molten metal elemental composition, arguably, remains one of the key unresolved issues impeding full automation and real-time optimization of pyrometallurgical operations in different industrial areas, including non-ferrous metals and ferro-alloys. In particular, current process control practices during Ni/Cu matte converting often rely on visual observations and typically involve matte sampling in order to confirm target matte composition. In addition to being time consuming, this approach relies heavily on operator experience and diligence, and, therefore, requires continuous performance and quality control efforts. For instance, the need to improve quality of the Bessemer matte (BM) at the Copper Cliff smelter has prompted an impressive staff engagement and training campaign that was carried out by Vale’s team in the late 2000’s (Zanini, Wong, & Cooke, 2012). This training exercise was executed to address the compounded effect of several operational challenges, namely demand for higher throughputs, changes in the feed concentrate composition, increased feed variability, loss of process knowledge and expertise due to retirement, as well as lack of a comprehensive approach to improving the overall performance of the flowsheet rather than meeting production targets for intermediate products. Although the campaign was very successful and has resulted in significant improvements in the Bessemer matte quality, it has also highlighted the need to move away from “the-art-of-converting” and develop analytical tools that would enable real-time process monitoring."

Jan 1, 2018

By Carle R. Hayward

THOUGH recent months have seen a rapid decline in lead-smelting activity and consequent uncertainty as to the future, the first half of the year showed progress in keeping with similar activity in other metals. Demand for scrap increased and various lead-bearing materials found their way to plants producing secondary lead. Some of these materials introduced complications into normal smelting procedure and were the cause of many conferences among plant officials attempting to find the most satisfactory method of treatment. If a blast furnace is to do itself justice it must be run with an open charge. Troubles inevitably result when materials are added to a charge which tighten it up and pre- vent free burning of the coke and con- sequent rapid smelting with a clean hearth This fact has long been recognized by plants producing primary lead, but only recently only it received the attention it deserves.

Jan 1, 1938

By E R. Ramanaidou

The value of Raman spectroscopy to undertake mineral and chemical characterisation of iron ores was assessed by applying the technique to representative samples of banded iron-formations (BIF) and a BIF-derived, martite-goethite ore. The common iron oxides haematite, magnetite and goethite as well as gangue minerals such as quartz and carbonates all show distinct Raman spectra that enables these phases to be easily detected and mapped in situ for either samples prepared as polished blocks or unprepared material. Raman spectroscopy also offers the potential of in situ chemical characterisation. Shifts in the excitation bands of carbonate detected in BIF were related to the Mg content of Fe-carbonate and confirmed the first world-wide occurrence of a high Mg-bearing siderite (pistomesite) in BIF.The discriminatory power of Raman spectroscopy coupled with the potential of the technique to offer large-scale (volumetric) characterisation of iron ore will be of great value not only to the existing BID and CID ore types, but also to the newly emerging magnetite iron deposits (MID).

Jul 11, 2011

By Henrique Lacerda Eleutério, Aldo Henrique de Almeida Barbosa, Vicente Tadeu Lopes Buono

The automotive industry’s interest in galvannealed (GA) boron steel for hot forming processes application has been steadily increasing due to its excellent surface quality, galvanic protection provided to the parts, good paint adhesion and better weldability in relation to other coatings for this application. In this study, samples of 22MnB5 galvannealed steel were heat treated and hot stamped on a water cooled die in laboratory scale. The influence of heat treatment on stability of coating and steel was assessed by using initial heating rates 11.0ºC/s and 15.0ºC/s. Microstructural evolution of galvannealed coating and structural integrity of steel during hot forming were investigated by scanning electron microscopy with energy dispersive spectroscopy analysis (SEM/EDS/Line scan), X-ray diffraction (XRD) and optical microscopy (OM). It was possible to quantify the Fe-Zn phase evolution during hot forming, to understand the effect of these heating rates on the product properties and to establish an optimized heat treatment for hot forming of these steel. The heat treatment with the heating rate of 15.0ºC/s presented greater operational flexibility and final products free from surface defects or cracks in the substrate.

Oct 1, 2019

By C. A. Young

Previous experimental results have shown that an increase in temperature and/or oxygen concentration leads to an increase in the hydrophobicity of fluorite (CaF2) with adsorbed oleate. Subsequently, ex-situ Fourier transform infrared (FT-IR) transmission studies suggested that this increase in hydrophobicity was the result of double-bond reactions between adjacent oleate species adsorbed at the fluorite surface. Now an in-situ FT-IR study on single crystals of fluorite has been used to monitor this phenomenon using internal reflection spectroscopy (IRS) with the crystals serving as reactive internal reflection elements. The double-bond reaction has been correlated with in-situ adsorption density measurements. These results demonstrate that only the first chemisorbed oleate layer undergoes the double-bond reaction at an appreciable rate. However, multilayers of precipitated calcium oleate in the case of fluorite appear to react minimally even for oxygen saturated solutions at elevated temperatures.

Jan 1, 1991