Search Documents

By R. Raby

During the 1980 decade, the rapid price increase for flake graphite has generated a high degree of interest for the discovery and the development of alternate occidental sources of supply in response to fluctuations in quality and availability from current producers. Alike many industrial minerals, graphite draws its complexity not only from its mineralogy and unique properties but also from the very large spectrum of industrial applications each calling for specific quality criterion. As new high technology uses are being developed, more rigid specifications will apply. Discovered during the latter part of 1988 by Mazarin inc., some 30 Km South of Fermont near the Quebec-Labrador border, the Lac Knife deposit was quickly identified as one of the world major long term alternate source of stable supply for this mineral. This paper also reviews the status of the project development as of late 1991, while updating previous papers published by Industrial Minerals1990 and Mining Magazine 1990.

Jan 1, 1992

By J. F. Shirley, H. K. Burke

In January, 1964, three years of laboratory and pilot plant test work reached its culmination. The San Manuel Div. of the Magma Copper Co. switched its molybdenite extraction circuit from the sodium hypochlorite-ferrocyanide process to the new process described in this paper. The San Manuel Div. Concentrator of the Magma Copper Co. is located near San Manuel, Ariz., approximately 45 miles northeast of Tucson. The concentrator treats approximately 35,000 tons of ore per day containing about 0.85% copper and 0.025% molybdenite. The San Manuel ore body is a disseminated copper deposit in quartz monzonite and quartz monzonite porphyry. The primary copper mineral is chalcopyrite; minor amounts of chalcocite, bornite and covellite are also present in varying degrees. Pyrite makes up somewhat more than half the sulfide content of the rock. The molybdenite is nearly always found on fracture faces or associated with quartz veinlets.' On January 9, 1964, the sodium hypochlorite-ferrocyanide process that had been used for molybdenite recovery was replaced by the following process: 1) A conditioning step with hydrogen peroxide, sulfuric acid, sodium cyanide and zinc sulfate. 2) A two stage rougher flotation step with stove oil and sodium ferrocyanide. 3) One cleaning step with sodium ferrocyanide. 4) One cleaning step with sodium hypochlorite and potassium ferricyanide. 5) Four cleaning steps with an anti-foam Exfoam 636 and potassium ferricyanide. COPPER CONCENTRATOR Since molybdenite recovery is closely allied with previous steps in the operation, the copper concentrator will be briefly described first. The ore is ground to approximately 5% plus 65-mesh and 65% minus 200-mesh in a two-step grinding circuit consisting of rod mills in open circuit and ball mills in closed circuit with rake classifiers. A straight forward rougher circuit producing only one concentrate is used. The rougher concentrate is combined with the discharge from the regrind ball mills and is then cycloned, with the overflow going directly to the cleaner circuit and the underflow going to the regrind mills. The feed to the cleaner circuit is approximately 90% to 94% minus 325 mesh. The cleaner circuit consists of two stages in which the tailing from the final cleaner stage is returned to the primary cleaner and the primary cleaner tailing is returned to the rod mill discharge at the head of the circuit. Approximately 0.013 lb of the allyl ester of amyl xanthate (S-3302) per ton of ore is added to the rod mills and approximately 0.006 lb of sodium isopropyl xanthate (2-11) per ton of ore is stage added down the rougher banks. The frother used is methyl iso-butyl carbinol (MIBC) and it is added at various points in the grinding and the rougher flotation circuits. Lime is added to the ball mills and/or to the rod mills to maintain the desired pH in the rougher flotation. The rougher flotation has been operated at various pH levels between 10.5 and 11.5. Fuel oil is added in the regrind mills at a loading of approximately 0.01 lb per ton of ore. Factors Which Directly Affect Molybdenite Recovery: It has been found at San Manuel that, to obtain maximum molybdenite recovery, an oily type flotation collector must be added in the grinding circuit. When molybdenite is crystallized in the characteristic platy form, which appears to be the case almost all of the time at San Manuel, its surface has a greater tendency to adhere to oils than water. 2 Of the several oily type collectors available on the market, the allyl ester of amyl xanthate seems to be the best molybdenite promoter. The floatability of San Manuel's molybdenite does not appear to be affected, at least up to a pH of 11.5, by lime. It has been reported that at several plant operations high lime alkaline circuits have adversely affected the molybdenite recovery.3,4 It has been found through microscopic studies that the bulk of the chalcopyrite will float before the molybdenite in both the rougher and cleaner circuits. It is necessary to add fuel oil to the regrind mills to enhance the

Jan 1, 1965

By A. J. Kraemer

This paper is the second and concluding report of the results of the twenty-fourth semiannual survey made by the Bureau of Mines of motor gasoline marketed in the United States. The first report7 on this 1931 survey gave the results of the examination of the gasoline samples in accordance with the new Federal specification for United States Government Motor Gasoline.8 The present paper reports results of the examination of the gasolines for color, doctor test, gravity, end point, per cent recovered, copper-dish gum, and steam-oven gum. The retail price and the tax at the time each sample was taken are also reported.

Jan 1, 1932

By Ralph H. Sweetser

OF SPECIAL importance in the design and construction of an iron blast-furnace plant are tile raw materials to be employed. Obviously the iron must come from some ore of that metal, but the many kinds available lead to important differences in plant arrangement, and in the design of furnaces and accessory equipment. For instance, the bulk of the gangue in the ore is subject to wide variation as is that of the ash in the fuel. A gradual increase in the bulk of raw material necessary to produce a ton of pig iron has been noted, but this has been more than offset, so far as costs of operation are concerned, by improvements in the machinery used for handling large quantities of ore. coal limestone, and slag. The mechanization of coal and iron-ore mining. the building of big ore boats and limestone carriers, of ore docks for fast loading and unloading, and the general use of heavy railroad equipment have all contributed to greatly reducing the number of man- hours required to mine, transport, and manufacture the raw materials into a ton of pig iron. This looks like a big saving and it is. If it were not for these big labor saving machines it would be impossible to produce the tonnage of iron and steel that is made each year in this country. On the other hand, the total capital investment necessary to bring down the man-hours per ton of pig iron to a 2.3 hours average at the blast furnace and to a total of only 12 man-hours from ore to metal (see Table 1) is so great that even the present high price of pig iron is probably not far above the true cost of manufacture when all the fixed charges are properly included.

Jan 1, 1939

Discussion of the paper of B. H. Dunshee, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 30, August, 1913, pp. 1511 to 1531. GEORGE E. MOULTHROP, Butte, Mont.:-The recording for the first time by Mr. Dunshee, in a readily usable form, of the various systems of square-set framing applied in the Butte district is a valuable contribution to mining information. The many different methods of framing employed, due to the individual ideas of superintendents and foremen of segregated companies, have given full opportunity to determine the best framing for the conditions as found in these mines, and the final adoption of a system uniform for all the mines has come about through a study of these various methods and an experience covering a period of many years. The sawed 10 by 10 in. and 12 by 12 in. timbers undoubtedly give the best satisfaction; and the style of framing the sawed timber that under all conditions has given the best practical results is that used in the Anaconda group and other mines, described and recommended by Mr. Dunshee. In this framing the posts have a horn 2 in. high and 6 in. square, the cap end having dimensions of 3 by 6 in. Instead of the framed girt shown in the drawings of the Anaconda group, the 6 by 10 in. girt adopted at some other mines, which fits into the cap and post framing with no other preparation than cutting the timber to the necessary length, fills all the necessary requirements for strength and affects a material saving in timber and labor. This, as Mr. Dunshee states, is without doubt the type of framing which would be adopted as a standard for 10 by 10 in. sawed timbers if sawed timber sets were to be used in the future generally. But saw-timber for the mines was becoming scarce and expensive, and round timber for the square sets furnished an alternative which provided, at greatly reduced cost, material which in every way supplied the requirements of the mining conditions. The use of the round timber with a satisfactory framing makes available a conveniently located and large source of supply which up to this time has served no useful industrial purpose. Particularly is this true of small timber, which is still standing in great quantities in the forests where the trees more desirable for commercial purposes have already been cut and marketed.

Jan 11, 1913

By A M. Ebbels, D Pratt

The current commodities super-cycle has seen an explosion in the number of mining projects demanding human resources throughout the world. The demand for key personnel currently far outweighs the international talent pool and will take several years to subside. A highly effective project team can be the difference between a successful project and a bad public relations exercise. Building an effective team and retaining the team members has become one of the major influencing factors for successful project development in the mining industry in the last decade.Increasingly, international teams are being established combining skill sets, subject matter experts, unique previous experiences and diverse cultures to deliver mining projects all around the world.This paper explores the characteristics of a highly effective team, the communication and geographic challenges and some potential pitfalls which influence the ability to form effective teams within the mining industry.CITATION:Ebbels, A M and Pratt, D, 2012. A great project team - Bringing together location and culture, in Proceedings Project Evaluation 2012 , pp 197-202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By James R. Jones

The purpose of these opening remarks is to establish a viewpoint, which will form part of the basis for later discussion between panel members and between the panel and the audience. Important issues will be identified. These ideas in the form of questions and answers, hopefully, will provide the necessary background for the ensuing dialogue. Is There An Urgency? We do not believe there is the urgency for immediate control legislation that has been depicted by some Congressional sources, environmental groups, and certain segments of the press. Emissions of sulfur oxides in the United States have decreased 15% during the 19701s, even though the use of coal by electrical utility power plants increased nearly 80%. That trend will continue as the older plants are phased out of operation and are replaced with newer plants, which must meet the New Source Performance Standards (NSPS) requiring the use of "scrubbers" to reduce sulfur dioxide emissions by 70% or 90%. The present Clean Air Act Amendments of 1977, by allowing the logical progression of economic events- -depreciation, retirement, replacement, and growth--will produce approximately a 50 % reduction in SOX emissions by the year 2015.

Jan 1, 1984

By F. L. Kadey

A discussion of fillers would not be complete without allotting adequate time to that unique and different mineral material, diatomaceous silica. Historical references to its use challenge the aesthetic aspect of man's curiosity; whereas modern scientific tools have provided a dimension of measurement that has motivated many of its more recent applications. A brief review of what is already known is in order. The diatom is a unicellular, plant-like, microscopic organism, related to the algae1. Its natural function appears to be that of a food for other marine or lacustrine organisms, The diatom's "claim to fame" from an industrial viewpoint is dependent on the fact that it secretes an opaline siliceous skeleton that must survive, chemically and structurally, the geologic processes that caused its formation in the first place; its subsequent demise, burial, consolidation, and alteration; and finally, its ultimate exploitation by man--in somewhat that order. In addition to its siliceous nature, the skeletal structure of the diatom possesses a variety of shapes, patterns, and sizes that have not only been the intrigue of microscopists for decades, but have served to set diatomite apart as an industrial mineral; and have reserved for it applications that cannot be satisfied by any other material. Its chemical inertness, its intricate structure, and its intrinsic hardness-coupled with fineness and friability-- are generally known and have accounted for its application in a wide range of filtration and filler uses. The increasing use of the electron microscope has considerably expanded our knowledge of heretofore unseen secondary and tertiary structure of submicron dimension in the diatom valve. The development of electro-sensing methods of particle size measurement which seem to supersede sedimentation and microscopic techniques has portrayed size distribution in a more realistic light. Interest in the surface chemistry of these silica structures has further strengthened our understanding for certain uses. Thus, new tools and ideas have made possible the introduction of diatomite into such sophisticated technologies as that of chromatographic supports, its improved utility in paint applications for the control of gloss and sheen, and its usefulness in the entirely new concept of "Dry Acid Concentrates." Each of these applications has been discussed elsewhere before people particularly interested in analytical chemistry, in paint, and in liquid handling, respectively, where the diatom has been a means to an end. The emphasis here, before the mining fraternity, however is on diatomite as a raw material with reference to the uses mentioned above. It is therefore toward an awareness and understanding of diatomite properties pertinent to these newer filler applications that this paper is directed.

Jan 1, 1967

By S W. Houlding

The Certificate in Mining Studies program at the University of British Columbia, Vancouver, Canada is a collaborative initiative between mining schools and industry to provide accessible, cost-effective, accredited continuing education and training, designed to address the future needs of the global mining community. Content is provided by industry specialists and delivered through an integration of online learning, short courses and interactive webcasts. Accreditation is provided by a network of mining schools. In 2011, the program will deliver close to 100 short courses and interactive webcasts and provide 24/7 access to more than 130 online courses in six mining streams, to participants from as far afield as Tanzania, Argentina and Mongolia. The program is proving adaptable to corporate and mine site engineer-in-training and graduate-development programs, as well as providing accessible professional development opportunities for individuals. It also provides opportunities for cross-training from other disciplines and integration with mining school curricula.

Nov 22, 2011

By Guy Ervin, Delwin D. Blue, John E. Conley

"INTRODUCTION Extraction of alumina from various materials, such as low-grade bauxite and clay, by means of a lime-soda sinter has been the subject of a number ofinvestigations (1, 2, 3, 4, 5, 7, 9, 10, 11, 12, 13, 16, 17). 5/ in recent years, Although many of the details of these investigations are lacking, it is believed that there is one difficultly that frequently develops under certain conditions, namely, that of thickening or gelation of the slurry formed during extraction of the sinter. If gelation occurs even to a slight extent* Serious mechanical difficulties result, very low liquor recoveries are obtained, and the extraction step becomes virlually inoperable. Under 'favorable conditions, a solid gel is formed which can only be removed from the equipment with great difficulty. At the Eastern Experiment. Station of the Bureau of Mines in College Park, Md., a study of lime-soda processes was begun in November 1941. This work has included studies on low-grade bauxites, kaolin clay, and nodular diasporic clay. Gelation was most serous with kaolin clay and least with diasporic clay. As a part of the Bureau's investigation, a study was made of the effect of the pertinent variables on gelation. The results permit the selection of various sets of conditions at which gelation will not occur. These data are essential to the final selection of optimum conditions for the over-all process."

Aug 1, 1946

By N. Erarslan, M. Ghamgosar

With the increased use of mechanized rock excavation, there have been developed internationally a number of methods to assess the abrasivity of rock materials. These methods range from determination of abrasive and hard mineral content using petrographic thin section analysis to weight loss or rate of wear flat development on specified test pieces. The Cerchar abrasivity index (CAI) test has been widely accepted for the assessment of rock abrasiveness and is determined as the abrasion of a steel pin after scratching over the freshly-broken or saw-cut surface of a rock. Two types of testing devices are in use today: (i) the original ‘Cerchar apparatus’, and (ii) the ‘West apparatus’, which was adopted herein. The CAI is calculated from the measured diameter of the resulting wear flat on the steel pin after 10mm scratching. This test has been considered to provide a reliable indication of rock abrasiveness for isotropic rocks. However, a great amount of rocks in natureis anisotropic. Phyllite is an anisotropic and foliated metamorphic rock and various types of phyllite specimens were tested in this research. Although phyllite is a type of rock primarily composed of quartz and the expected CAI value can be high, mechanical cutting of this rock should not be very problematic compared with igneous rocks have same CAI value. As phyllite is a foliated metamorphic rock, most of the specimens split into sheets through the quartz seam by the tip during scratching normal to the axis of quartz seams. Hence, viability assessment of Cerchar abrasivity test and F-Schimazek index values for the anisotropic rocks is investigated in this research.

Jan 1, 2015

By G. W. Ostroot, S. Shryock

Cementing deep, high-temperature oil wells where static temperatures range from 350 to 400F has become routine in the part decade. In the United States there were 271 wells drilled deeper than 15,000 ft during 1963. Many of these wells had static temperatures higher than 400F. Bottom-hole static temperatures near 700F are now realities in the geother-mal (steam producing) wells of California's Salton Sea area. The detailed planning initiated prior to drilling the wells is discussed together with the methods, materials and equipment used in solving the cementing problems which are encountered. Data are also presented that lead to development of cementing compositions that provide adequate thickening time, do not retrogress in strength, and maintain low permeability under these extreme temperature conditions. Field data include the cementing programs used on eight relatively trouble-free geothermal steam wells in the Salton Sea area. INTRODUCTION Not too many years ago cementing oil wells with temperatures in the range of 300F caused considerable anxiety. In some areas of the United States it is now fairly common to cement wells having bottom-hole static temperatures in excess of 400F. We are now confronted with the problem of cementing wells with temperatures ranging from 500 to 700F. Temperatures in this order of magnitude are often found in geothermal steam wells. From where does this extreme heat emanate? There are many theories as to the source of this steam flow. The most widely held views are: (1) heat- ing of ground water fairly close to the surface by an intrusive mass of hot rock; (2) steam generation from a reservoir of metamorphic rock, normally found below 25,000 ft and not at the shallower depths of the Salton Sea reservoir; and (3) high-temperature gases (water vapor) escaping and migrating from molten or semi-molten rock (magma) at a considerable depth. Of these. No. 3 seems to be the most generally acceptable explanation. Heat from springs and fumaroles has been used for years as a means of heating and cooking; however, significant progress in harnessing the vast power of underground steam reservoirs has been relatively slow. The first large-scale attempt to use the heat generated by steam from wells was made in Italy around the beginning of the 20th century. In excess of 250,000 kw of electrical power is now being produced from holes around Larde-rello, Italy. Another very active drilling program was initiated in the volcanic area of New Zealand in 1949.' Natural steam for power projects in the United States began in the early 1920's. An early commercial steam field is located at the Geysers, approximately 75 miles north of San Francisco, an area discovered in 1847 and used for many years as a health resort. Steam originates from 15 wells that have been drilled since 1957. The present output from this project is 25,000 kw. Success of the Geysers operation has been responsible for several companies taking a careful look at the feasibility of producing steam for power generation in the Salton Sea area of Southern California's Imperial Valley. Geothermal steam activity in this latter area began in 1961 when O'Neill, Ashmun and Hilliard completed Sportsman No. 1, at that time the hottest wellbore in the world.' Since its References given at end of paver. completion seven additional wells have been successfully completed in this area. Many problems encountered in drilling steam wells had to be overcome to make the ventures successful. Formation temperatures encountered in the Salton Sea seemed to be a straight-line function (a gradient of 13F per 100 ft of depth).' This imposed severe conditions on all aspects of drilling and completion. This varied, to some extent, from gradients in the older geothermal areas. Not to be overlooked is the effect of these temperatures on casing creep or elongation by thermal expansion (Table I), because standard API flanged wellhead equipment makes no provision for this kind of performance. Floating equipment was redesigned, and changes in types of downhole equipment were made in an effort to eliminate anticipated problems. In the later completed wells, standard oil-well cementing equipment has been used. During the early development of geothermal steam wells there were some problems resulting from blowouts. However, these were eliminated in the deeper Salton Sea wells and no problems were encountered with the drilling mud. A sodium surfactant mud was used on the Sportsman No. 1 to drill from 2,690 to total depth. Nevertheless, it was necessary that a cooling system be added and the mud cooled before circulating it back into the well. The difficulty in evaluating the size of the steam area and its potential in terms of pounds of steam and years of productivity still has not been resolved. Economic complexities have also entered into the steam play in the Salton Sea. The wells at the Geysers were drilled at a cost of $15,000 to $20,-000, whereas the Salton Sea wells will cost more than $150,000. This cost differential has to some extent been accounted for because of the heavily

Jan 1, 1965

By Cecil H. Desch

THE progress of metallurgical practice and the demands made by the engineering industry on our foundries and mills have made the crystalline structure of metals a subject of far more than academic interest. Metals and alloys are made up of crystals. Even if we accept the view, so ably maintained by some metallurgists, that the crystals are separated from one another by an amorphous layer, it remains true that all but a very minute fraction of any metallic mass is crystalline. The conditions which affect the growth of crystals are therefore of importance in metallurgy. It is not only castings whose properties depend on the arrangement of their crystals, for the more we learn of the behavior of forged, rolled and drawn metals, the more certain it becomes that it is profoundly influenced by the size and arrangement of the crystals in the original ingot, deter- mining a structure which may persist in a modified form through a long series of mechanical operations and annealings. This is mainly due to the concentration of much of the impurities in the last portions of the liquid to freeze, so that the boundaries between single crystals or groups of crystals are marked out by a zone of segregated material, differing in properties from the mass, and offering a barrier to diffusion and equalization of composition throughout the whole. The importance of this fact has been fully recognized by steel manufacturers, who have to deal with ingots which are sometimes very large, and are cast at a high temperature, containing impurities which have a marked effect on the properties even when present in very small quantity. For this reason the Iron and Steel Institute has set up a committee to examine the whole question of the heterogeneity of steel ingots,(l)f and a report has been issued, containing an account of the structure of 16 ingots, ranging in weight from 15 cwt. to 172 tons, each of which was sectioned and examined by chemical analysis and by etching. A valuable body of data concerning segregation has thus been collected. The work of the committee is being prosecuted with great activity, and at the same time researches are in progress to determine the physical

Jan 1, 1927

By AIME AIME

THE Petroleum Division opened its proceedings on Wednesday morning, with two simultaneous sessions on engineering and economics. The first paper at the engineering session, over which A. W. Ambrose presided, was "Underground Surveys of Oil Wells," by Alexander Anderson of Los Angeles, Calif., was presented by John Suman of the Humble Oil & Refining Co., Houston, Texas. Following this, the paper of E.'H. Griswold of the Mailand Oil Co., Houston, Texas, was presented by C. V. Millikan of the Amerada Petroleum Corp., Tulsa, Oklahoma. Following the presentation of these two interesting papers a general discussion followed on the subject of "Crooked Holes." The discussion was entered into by F. H. Lahee, Sun Oil Co., Dallas, Texas;'Messrs. Bigelow of Tulsa, H. W. Hixon of New York City, Van Court Warren of Los Anyeles, Calif; H. L. Wheeler of St. Louis, Mo.; R. R. Brandenthaler, United States Bureau of Mines, Bartlesville, Okla.; H. H. Riggs, Indiana Territory Illuminating Oil Co., Bartlesville, Okla.; C. V. Millikan and John R. Suman

Jan 1, 1929

By K. A. Brunk

Newmont's research, operations, history and experience with pre-treatment of preg-robbing carbonaceous ores are described, with emphasis on the chemistry, physics and kinetics of chlorine treatment. Present operations, control strategy and projected changes are also described, including a summary of the adsorption of chlorine into pulps and off-gas scrubbing. Conditions of chlorination have been optimized by the use of Eh-pH diagrams of the gold-chlorine-water system, and have resulted in significant increases in gold recoveries and decreases in chlorine consumptions.

Jan 1, 1987

By Elaine T. Cullen

Safety training materials appropriate for specific underground noncoal operations in the United States are often outdated or nonexistent. The Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and H ealth has developed several new training tools, including three videos on common underground activities, software that will allow trainers to create a virtual training mine using their own mine map, and toolbox training materials. SRL is working closely with industry in the development of these tools. Teams of safety professionals are involved in the early stages, and actual mines and miners are involved throughout the production phase. This presentation describes the development process and results of SRL’s safety training projects.

By Rongjie Kong, Shiwei Wang, Guomin Wei

Owing to the selective oxidation and uneven combustion that occur on the surface of carbon anode, some carbon particles detach and form carbon residue, which is defined as spent anode slag (SAS). The highly graphitized and toxic impurities such as fluorite ( CaF2), corundum (α-Al2O3), and cryolite ( NaAl11O17) are crucial components of SAS resource but are difficult to separate from graphite. This study developed a method of using water-soluble (emulsified) kerosene to separate the carbon particles from the toxic impurities in the SAS resource. The flotation purification approach of utilizing conventional kerosene was experimentally investigated and compared with that of using water-soluble kerosene. The results showed that with the use of emulsified kerosene, the maximum combustible matter recovery of the carbon particles was 89.86% while that of using traditional kerosene was 80.30%. The emulsified kerosene was comprehensively examined by various instruments to clarify its adsorption mechanism on the carbon particle surfaces. Because of the superior dispersibility of emulsified kerosene, it effectively envelops carbon particles with a smooth surface, oxygen-containing functional groups, and hydrophilic C–F bonds, thereby increasing the surface hydrophobicity and flotation responses of targeted carbon particles.

Feb 6, 2024

By Wangzhi Zhou, Jian Xu, Jing Zhang, Xuecheng Gong, Mingsheng He, Guohua Xie

Graphite, which has a unique stack structure that enables a small friction coefficient, is used as one kind of the best hearth rolls to support and convey silicon steel strip in continuous annealing furnace. However, the buildup formation in/on the surface of carbon sleeve has always been a worldwide difficulty in the silicon steel industry. Based on the analysis of the microstructure, topography and composition of the buildups, combined with simulation experiments, the mechanism of forming buildups is discussed. The results show that buildups experience the process from nucleating to growing-up, and buildups are formed by nano liquid phase sintering (NLPS). Meanwhile, some countermeasures to reduce or prevent the formation of the buildups are proposed.

Mar 1, 2018

By JO Choi

Jet-grouting method is a useful technique to reinforce foundations on relatively soft or vulnerable soil layers such as fractured zone and stratum with cavities. Although jet-grouting has been widely applied to various field works, a reliable design standard has not been established yet. A number of model tests were performed to investigate end bearing behaviors of piles reinforced by jet-grouting. It was concluded that end bearing capacity was increased in proportion to uniaxial compressive strength of grout column. Based on the test results, the design criteria for the end bearing capacity were suggested.

Jan 1, 2006

By D. M. Waldorf

Steam permeability measurements have been made in the laboratory on several samples of natural reservoir materials. The steam temperatures and pressures were selected to simulate conditions which might exist in a reservoir during the injection of steam. For each sample tested, the experimental permeability to superheated steam was comparable to that measured with air and no evidence of plugging was detected. Some samples were exposed to water at various temperatures and plugging was found to occur in materials which contained significant quantities of monmorillonite clay. Temperature had little effect on the degree of plug-ning between 75 and 325 F. The measured pemeabilities tended to increase slightly with temperature, but the changes were small compared with the initial loss of per~neability on wetting. Sequential pemzeability measurements were made on two samples using air, water, steam, water and air, in that order. Both samples were water-sensitive and plugged extensively after the initial injection of water. Upon exposure to superheated steatm the samples dehydrated and their permenbilities to superheated steam were comparable to those initially measured with air. The remaining measuretnetzts with water and air confirmed that the water plugging was reversible and that the samples were not seriorrsly damaged during the tests. INTRODUCTION The swelling of water-sensitive clays during water floods has long been recognized as a potential source of reservoir damage. The recent extensive application of steam injection and stimulation has compounded this problem since both hot water and steam (as well as fresh water at reservoir temperatures) are, at sume time, in contact with the producing zone adjacent to the bore of a steam injection well. The purpose of this paper is to present data which compare the sensitivity of some natural sedimentary rock samples to water at various temperatures, and to super-heated steam. Some properties of montmorillonite clay are briefly reviewed, and comparisons are drawn between empirical data and the predicted behavior of the montmorillonite known to be present in the samples. PROPERTIES OF MONTMORILLONIT E CLAY Water initially adsorbs on dry N a -montmorillonite clay in discrete layers in the interlaminar space between clal platelets. The platelet spacing, which is 9.6 A (angstroms) for a dehydrated clay, has been observed to expand in discrete steps to 12.4, 15.5, 18.4 and 21.4 A spacings, indicating the formation of four discrete layers of regularly oriented water molecules.' The first two layers are easily formed by hydrating a dry sample to equilibrium in an atmosphere with carefully controlled humidity. The formation of the higher layers is more difficult. The usual X-ray diffraction patterns of the more highly hydrated samples indicate a gradual increase in the average spacing betwcen 15.5 and 19.2 A, followed by a discontinuous expansion to 31 A when the weight ratio of water to dry clay is between 0.5 and 1.2.' Platelet expansion above 31 A proceeds monotonically as the moisture is increased and no regular arrangement of the platelets ib observed. Water-sensitivity in sedimentary rocks is usually associated with Na-montmorillonite clay when it is in the noncrystal-line state. Mering3 found that the average lattice spacing of sodium montmorillonite hydrated at 68 F and 70 per cent relative humidity was 15.5 A, and that the spacing, at 92 per cent humidity was 16.5 A. The water adsorbed at the higher humidity has the same free energy as liquid water at 65.6 F. Kolaian and Low' used a tensiometer to measure the thermodynamic properties of water in diffuse suspensions of montmorillonite clays relative to pure water. They observed that water in suspensions as dilute as 6 per cent clay became partially oriented when left undisturbed. The bonding associated with this orientation was not extensive because the free energy difference between the water in suspension and pure water was only a few millicalories per mole. They also found that the measured free energy difference decreased rapidly with temperature and became negligible above 100 F. This evidence indicates that montmorillonites contained in sedimentary rocks would dehydrate to a crystalline structure when exposed to superheated steam, and that the rock permeability measured with steam would be equivalent to that measured with air. The effect of elevated temperatures on the swelline of montmorillonite clays in aqueous suspensions has not been investigated. The Gouy-Chapman diffuse-ion-layer theory has been used to predict the swelling pressure of clay suspensions in dilute salt solutions at room temperature with reasonable success. theory also correctly predicts the direction of the thermal response of Na-mont-morillonite swelling pressures in dilute salt suspensions, 9 Over the temperature range of 33 to 68 F, an increase in

Jan 1, 1966