Search Documents

By C. A. Pearson, W. D. Dietzman, M. E. Hawkins

Results of chemical analyses and electrical resistivity measurements of 422 samples of oilfield brines from 120 east Texas fields in Railroad Commission of Texas Districts 5 and 6 are presented in tabular form . These samples represent water from all of the major petroleum- productive formations in the area . Water analyses and electrical resistivity data , when fully utilized by proper study techniques , are useful tools in the solution of many engineering problems such as detection of well leaks , identification of water sources , and interpretation of electrical well logs . In the area included in this study , these representative data should facilitate the solution of problems in which water analysis and water resistivity are factors .

Jan 1, 1964

By William G. Pariseau, Mark K. Larson, Heather E. Lawson

Rational design based on engineering fundamentals is essential for the layout of safe, stable shafts and tunnels. Shafts and tunnels including winzes, raises, adits, and crosscuts are lifelines to the underground and must be secure. The contribution of this paper describes a significant extension in existing software previously developed for five important design problems in strata-bound mines such as coal, trona, salt, potash, and some large, lead-zinc mines. This extension in software allows analysis to proceed in three easy steps: (1) preparation of a strata properties file, (2) generation of the finite element model, a mesh, and (3) finite element program execution. Circular, elliptical, and rectangular shaft sections are available for a single shaft, twin shafts, and shafts in a row. Spacing of twin shafts and shafts in a row is a free parameter (pillar width). Tunnel shapes are the same as shafts but include the conventional arched back section. Dipping strata of variable thickness, depth and orientation relative to the excavation of choice are allowed. The analyses are three-dimensional. An elastic-plastic material model based on associated rules of flow and an N-type yield condition for isotropic, transversely isotropic, or orthotropic rock are used for all strata. Example analyses from several hardrock mines are provided to illustrate the three-step process including mesh plotting and plotting of selected results. The goal of this software is to advance mine design technology for improved miner health and safety.

By K. J. Palmer, D. A. Silva

"Evaluating resources and reserves requires the reliable modelling of geological domains and their grades. “Multiple point statistics” simulation is a relatively new geostatistical method to generate complex, high-resolution geological models by extracting high-order spatial relations from training images. A method based on combining multiple training images is developed to obtain the correct amount of large-scale continuity and short-scale variability. A calibration process matches the geological spatial variability between the final realizations and the drillhole dataset. A case study with data from the Red Dog mine, Alaska, United States, shows an appropriate reproduction of short-scale variability along boundaries between geological units.RÉSUMÉ L’évaluation des ressources et des réserves exige une modélisation fiable des domaines géologiques et de leur teneur. La simulation par « statistique multipoint » est une méthode géostatistique relativement nouvelle pour générer des modèles géologiques complexes à haute résolution par l’extraction de relations spatiales d’ordre supérieur à partir d’images d’entraînement. Une méthode basée sur la combinaison de multiples images d’entraînement est développée afin d’obtenir la bonne quantité de continuité à grande échelle et de variabilité à petite échelle. Un processus d’étalonnage fait correspondre la variabilité géologique spatiale entre les réalisations finales et l’ensemble des données de forage. Une étude de cas avec des données de la mine Red Dog, Alaska, États-Unis, montre une reproduction adéquate de la variabilité à petite échelle le long des limites entre les unités géologiques."

Jan 1, 2015

IN carrying out experiments to determine the amount of metal taken away by fume or fine dust the apparatus used requires to be strong and compact, as it is generaIIy necessary to work on a staging fixed at considerable distance above the ground and against a smoke stack or flue. It is essential that the test be carried out at a part of the stack welI away from any bends, to prevent eddies. The method described below has been used for estimating the dust losses from Dwight & Lloyd sintering machines, antimony drossing furnaces, pot sintering trials, etc., and has been founc! satisfaetory. It is welI to bear in mind that the longer the period over which dust coIIection is extended, the more valuable the result is likely to be. The rateof aspiration of the gases through the apparatus is kept as regular as possible by changing the filter thimbles frequently, and the rate of flow should correspond closely with the rate of flow of the gases up the stack.The apparatus required for carrying out a test is as folIows :-{a) Thermometers : two are required, one for taking the temperature of the gas in the stack and one for giving the temperature of the gas in the aspirating drum. If the temperature in the stack is over 400° C., it is advisable to use a pyrometer such as the "Bristol" the couple being standardized before use at about the temperature of the stack.(b) Pilot Tube: The foIIowing sketch (Fig. 1) iIIustrates the principle of the pitot tube. The readings are to be taken in a straight flue, or stack, preferably 20 diam. away from any bend. A, which is open, faces the air current and...

Jan 1, 1922

By A L. de Ambrosis, S J. Clarke

In the non-codified realm of tunnel design there are issues which are sure-fire instigators of controversy. This paper presents a discussion regarding one particular issue which in the authors’ experience often results in comment and debate. This issue only forms part of the rock load assessment process, but it is specifically addressed with the intention of presenting a rational basis for design, which may result in broader acceptance within the tunnel design community.The issue considered relates to the characterisation of in situ rock stresses for the design of tunnel support in the Sydney Basin. A summary is given of the literature on the topic, with emphasis on the main sources of uncertainty and contention. A design approach is proposed, with particular focus given to the numerical modelling of in situ ground stresses and the approach used to ensure that the adopted stress regime is consistent with the assumed ground model. The resulting variability in the initial stress field is discussed and comparisons made to the test database.CITATION:de Ambrosis, A L and Clarke, S J, 2014. Characterisation of in situ stresses for tunnel lining design in the Sydney?Basin, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 247–252 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Dennis Hoffmann

"Abstract - Banded iron formation rocks associated with massive sulfide lenses in the Broken Hill Pb-Zn-Cu-Ag deposit in the Namaqualand Metamorphic Complex, South Africa , were investigated with respect to the geochemistry of manganiferous silicate-rich bands. Two common varieties of these are: amphibole- and garnet-rich iron formation bands. The results reveal that the former are enriched in Fe, Mg, Cu, Co and S. The garnet-rich bands are enriched in Mn, Ca, P, Pb and Ba with significant detrital contamination of Ti, Al, Zr, Cr, Y, V, Ni and Nd.The silicate-rich bands have compositions, in terms of, Si/Al, Si/Fe, Fe/Mn, La/Ce and Co/Zn, comparable to submarine chemical sediments which precipitated from hydrothermal fluids. The garnet­ and amphibole-rich bands are interpreted as ""evolved"" and ""immature"" hydrothermal sediments, respectively. The latter resulted from rapid precipitation after exhalation, whereas the former had a longer residence within sea water. The silicate-rich bands both exhibit increasing Mn/(Mn+ Fe) fractions, which are consistent with a variation expected from proximal to distal depositional settings. The prevalence of garnet-rich bands over amphibole-rich bands is interpreted as the result of injection of hydrothermal fluids from a single vent situated along the northwest margin of the Broken Hill deposit."

Jan 1, 1994

By J. T. Hanks

Process development is one of the principal tasks required in the course of turning an exploration discovery into a mine. Exploration geologists should have an understanding of the more important metallurgical processes and the test work required for each process. The paper discusses the important metallurgical processes, the test work and sample requirements for each, and the costs and time requirements to accomplish the testing. The limitations of reverse circulation drill samples for metallurgical testing are discussed. The level of process definition required to support engineering studies: scoping, pre-feasibility and feasibility studies are also described.

Jan 1, 1997

By Joseph Poplawski, Christian O’Keefe, Robert Maron

"Unique and difficult minerals processing measurement situations will be described and the application of passive array-based technology for performing these measurements will be illustrated. Examples of these situations include volume flow measurements in froth lines and flotation feed lines with entrained air, slurry lines with magnetite and other magnetic ore, slurry lines with abrasive or corrosive materials, high pressure lines, and slurry and non-slurry lines exhibiting scale buildup. Other situations include measurement of entrained air levels in pipes and in flotation columns. These measurements are achieved through CiDRA’s patented passive sonar array-based technology. This technology performs two independent measurements – flow rate and entrained air amounts. Two hardware implementations of this technology have resulted in a non-intrusive flow and entrained air meter which easily is installed on the outside of the pipe, and a submersible version for entrained air or gas holdup measurements which is used in flotation processes. Recent developments in extending this technology to solve other unique measurement problems such as valve movement confirmation will be covered.INTRODUCTIONThe minerals processing industry faces many unique and challenging process control conditions and environments. In terms of flow measurements, many of these situations are not being properly served by traditional flowmeters such as ultrasonic meters, magmeters, turbine meters, orifice plate meters, vortex flow meters, Coriolis flow meters, and venturi meters. A new class of flowmeters has been developed that solves these unique situations and flow measurement problems. This new class of flowmeter technology utilizes sonar-based processing algorithms and an array of passive sensors to measure not only flow, but also fluid composition. It does so accurately, reliably and without making contact with the fluid. These measurements are performed on practically any type of fluid within virtually any type of pipe.PRINCIPLE OF OPERATIONSonar array-based flowmeters are ideal for tracking and measuring the mean velocities of disturbances traveling in the axial direction of a pipe. These disturbances generally will convect with the flow, propagate in the pipe walls, or propagate in the fluid or slurry. First let us focus on the disturbances that convect with the flow. The disturbances that convect with the flow can be density variations, temperature variations or turbulent eddies. The overwhelming majority of industrial flows will have turbulent eddies convecting with the flow, thus providing an excellent means of measuring the flow rate as described below."

Jan 1, 2008

By Lloyd M. English

During the past 30 years, the research arena has changed significantly in all fields, mining included. The relative representation of the topics of research, how the research is performed and who has performed the research have all changed. Although there are a lot of subjective ideas and anecdotal "analyses" concerning these changes, there has been no actual study of these trends to verify the facts. This study was divided into six five-¬year periods for the purposes of comparison. Some of the trends analyzed are co-authorship, research areas, research sponsors and cooperative efforts. In today's research arena, 30 years is a long time. Technology has advanced more rapidly than in any time previously and that pace continues to increase. There are more researchers, more tools for research and an increasing number of companies, agencies and institutions engaged in research. The pace of change and its impact is often discussed and debated at professional meetings and in institutions that engage in research. These conversations will often influence the research decisions of the participants in directions to take or subjects to pursue.

Jan 1, 1995

By T. J. DeMull

The business of heap leaching requires accurate forecasting of metal production from the heaps. Business forecasts typically follow a format that project periodic (monthly, quarterly, or annual) product shipments based on anticipated operating results, e. g., tons of ore placed, grade of ore, and rate of leach extraction. Since revenue and cash flow are dependent on the metal production stream, forecasts of metal production are very important for project evaluation and business planning purposes. Nevertheless, production forecasts, particularly for new heap leach projects, have been prone to errors. The present paper identifies some of the pitfalls that would be encountered in preparing production forecasts for new heap leach operations and provides a checklist of considerations to assist in preparing a forecast. Also, the paper presents a case study of copper production forecasting used for the Sanchez Project, a heap leach operation located near Safford, Arizona, that is presently under development by AZCO Mining, Inc.

Jan 1, 1995

By E. Asselin

Electrochemical polarization experiments were conducted on alloy 625 in ammonia solution between 25 and 225°C and the results were compared with those of an oxygen solubility model. Results confirm that corrosion is under oxygen control, Normalized corrosion rates are determined based on the rate of oxygen diffusion to the corroding surface, and the corrosion rate at 200°C (-9.7 µA.cm-2) is roughly 24 times higher than the corrosion rate at 25°C (0.4 nA,cm-2), An oxygen-solubility model for Supercritical Water Oxidation (SCWO) conditions was generated using the Redlich¬Kwong-Soave (RKS) equation of state, Results of the model confirm many of the experimental observations from SCWO reactors which suggest that corrosion is at a maximum at temperatures just short of the critical point, The RKS/oxygen diffusion model predicts that the corrosion rate at 365° C is ?85 times higher than the corrosion rate at 25' C. Given that a normalized corrosion rate is obtained, this type of model could be useful for selection of SCWO reactor materials.

Jan 1, 2005

By Walter Wood, J. T. H. Cannarella, H. F. Yancey, R. E. Zane

More than 50,000,000 tons of bituminous coal and probably about the same quantity of anthracite are cleaned annually in the United States by wet methods. The water, fine coal, and impurities from the water used for washing ordinarily are recovered by moans of various forms of settling tanks. Settling and clarification may be hastened markedly, thereby greatly increasing the capacity of clarification equipment already installed, by the addition of substances to the washery water that cause the fine particles in suspension to agglomerate and thus settle more rapidly. This phenomenon, although well known and applied in other fields, has been used at only a few coal washeries in the United States. It is widely employed, however, as an aid in the recovery or disposal of fine coal or impurities, as a means of preventing, stream pollution, and to enable reuse of washery water at many plants in Europe. Pioneering work in the United States has been done principally by two companies -- the Pittsburgh Coal Co., in Pennsylvania, 6/ and the Pacific Coast Coal Co., in Washington.

Feb 1, 1940

By J. E. 214-000-000-010 Warren, M. R. J. Wyllie, T. Meidav, L. Scharon, R. Uhley, A. J. deWitte

By considering the stoichiometry of the underground combustion process, an equrztion was derived relating the point velocity of the combustion front as a function of the air flux, fuel content, efficiency' of oxygen uitilization, hydrogen:carbon ratio, and ratio of carbon dioxide In carbon monoxide produced. In addition, an equation for cnlcrllating the amount of injected air necessary 10 produce the oil from I Cu. ft of reservoir space was derived. This equation has a direct bearing on evaluating compression costs for the process. Values calculated from these equations are in good agreement with experimentnlly obscrvcd values obtained from laborator) tube runs reported in the literature. The equations are also u\eful for atlcrlyzinf: experinlental data for inconsistencie.r.. I NTRODUCTION The injection of energy in the form of heat into an oil-bearing formation as a means of increasing the recovery of oil has been the subject of much discussion and experimentation as far back as 1920. The ideas have ranged from the injection of steam to the direct use of electricity as a means of getting thermal energy into a formation. However, most laboratory and field studies have been confined to the process whereby a portion of the crude in the reservoir is burned to generate the necessary heat to increase the mobility of the oil by reducing its viscosity. A recent paper by W. L. Martin, et al.', described the results of a number of laboratory experiments in which the combustion process was studied in a sandpack. Studies such as this indicate that with the temperatures involved, the oil is partially coked in this process and it is this coke which provides the fuel for combustion. The combustion of this residual coke can be analyzed theoretically by applying simple stoich-iometric principles to the combustion process. It is the purpose of this paper to compare the results reported in these experiments with those obtained from theoretical considerations. The variables studied by Martin, et al, among others, include combustion front velocity, air flux, oxygen utilization, fuel concentration, ratio of carbon dioxide and carbon monoxide in combustion gases, and the hydrogen:carbon ratio of the residual fuel. All these variables come into consideration when the stoichiometry of the combustion process is studied. The experimental conditions and results are tabulated in Tables 3 and 4 of Ref. 1. For purposes of comparison with calculated results, it was necessary to change the units of a number of the variables. UNDERGROUND COMBUSTION STOICHIOMETRY The combustion or oxidation of the carbonaceous residue or "coke" on the sand can be described in terms of the equation: where n is atomic ratio of hydrogen to carbon, m is ratio of moles of CO2 to CO produced, and CH. is taken as the unit molecular weight, realizing that actually the coke has a large range of high molecular weights. Assuming that all the fuel laid down in the sand is burned, the ratio of moles of oxygen consumed to moles of coke can be written as follows. Moles 0MolesMolescoke In terms of moles O2 per pound of coke, where 12 + n is the molecular weight in pounds per mole. If the 0, consumed is measured in standard cubic feet (60°F and 1 atm) and the coke in pounds per cubic foot of formation, 2, then:

By Yuanfei Chen, Jianfeng Zha

"China is the largest producer and consumer of coal in the world. The mining-induced surface subsidence has bad influences on the surface and structures above the surface. In order to minimize disasters, removal, reinforcement, or maintenance structures are often adopted. In the application of maintenance methods, it is necessary to carry out dynamic surface subsidence prediction to choose maintenance methods, optimize maintenance time, and evaluate the amounts of work. Time series methods and influence function methods are common for dynamic surface subsidence prediction, but the former is difficult to consider with underground mining conditions, and the latter has low prediction precision. Therefore, this paper develops a dynamic subsidence prediction model aided by field-measured data and realizes the model programming. The model could achieve high-precision prediction of dynamic surface deformation through optimizing the parameters in time by using field-measured data of surface subsidence. The research results of engineering cases show that, with the method of dynamic prediction, the standard error can be controlled in the range of 5%, greatly improving the accuracy of dynamic prediction of mining subsidence, which provides strong technical support for the maintenance and management of structures. INTRODUCTION With the rapid economic development and continued industrialization process, the demand for energy is growing in China. Today, China is one of the largest coal, oil, and gas consumers in the world. Coal consumption accounts for 47.7% of the total consumption in the world (Tian, 2016). In order to meet the demand for coal resources in the process of modernization, more and more coal mines carry out coal mining under villages, buildings, highways, and bodies of water. The mining-induced overlying strata and surface subsidence have bad effects on surface and on various structures (such as buildings, railways, highways, high-tension transmission lines) and could even cause various disasters (Williams et al., 1998; Bell et al., 2000; Doyle et al., 2002). Generally, methods, such as removal, reinforcement, or maintenance are taken to eliminate the adverse impacts (Kraatz, 1984; Bell and Genske, 2001; Wang, 1989). When reinforcement or maintenance is selected to remove bad effects, the proper maintenance methods must be chosen. In addition, maintenance time, as well as an evaluation of time it will take to do the work are necessary to predict the surface subsidence with high precision."

Jan 1, 2017

By Ma Shao Xian, Li Dong, Li Zhen Guo

"The new type shaft calciner ( SK-10 Serials) is developed and designed by CADRE itself on the basis of the conventional shaft calciner. The actual application in a number of calcinations plants have proven that they are of very good effect. Calcined coke calcining heated by the shaft calciner has a high quality, lower lost by fire. The shaft calciner needs no additional fuel when it is working. Anode Carbon Plant and calcined coke Plant commonly used the shaft calciner in domestic. The waste heat from the shaft calciner can be recuperated to generate electricity and to make the steam for produce. Exhaust waste heat is recovered by 90% or more. The new type shaft calciner's structure is optimized by computer simulation for fire-wall structure, combustion air to fuel ratio, volatile combustion is fully in use, furnace cooling zone structure, the exhaust smoking structure and calciner heat balance. Furnace structure and production operating parameters has been got the best optimized results. This paper introduces the working principle and characteristics of the shaft calciner - the equipment for calcining of the petroleum coke. It also demonstrates measured process parameters of the new type shaft calciner. Through comparison with the rotary kiln and conventional shaft calciner, it proves its own technical characteristics and advantages: higher capacity, high quality products, provides more energy for power generation, equipment operation and maintenance costs lower.IntroductionChina's petroleum coke market is mainly dominated by the delay raw petroleum coke. Rotary kiln and shaft calciner are the main process equipment for calcined petroleum coke. As the shaft calciner burning less, no external fuel, waste heat utilization is high, long service life, the utilization rate in China is more extensive than the rotary kiln."

Jan 1, 2012

By Raymond E. Zimmerman

The use of standard dense-media cyclones is well known, as they have been in use for many years. They are especially well suited for operating at low separating densities and for treating difficult coals containing a high percentage of near-gravity at the point of separation. Very few modifications of the basic design have ever been made. The author recently, however, has been interested in the development of a new type of dense-media cyclone that has been produced in Japan. He has observed the testing of this unit and has collected much data which he feels should be of considerable interest to coal preparation engineers. He feels that this unit, called the Swirl Cyclone, may be of substantial value as an alternate to the standard cyclones. It is certainly worthy of further investigation. There has been relatively little written in English-language publications on the Swirl Cyclone. It was briefly described at the Fifth International Coal Preparation Congress. I It has been described in a general manner by the author in two prior publications. 2, 3 This paper proposes to describe this device in more detail and at the same time submit technical data illustrating its wide characteristics.

Jan 1, 1977

By M G. Aylmore, L W. de Klerk

Roasting of refractory gold ores has been a commercial process for many years. Improvements in design of fluidised bed roasting technologies and low capital and operating costs compared with other refractory treatment processes can potentially make roasting a viable option.However, gold extraction from roasted ores carried out on laboratory scale equipment often invariably yields lower recoveries than other processes such as bio-oxidation or pressure oxidation. Non-optimal laboratory roasting conditions can incorrectly write roasting off as a process option.Low gold recoveries from the cyanidation of calcine products from roasting can often be attributed to roasting conditions not favouring gold liberation and agglomeration processes, particularly if lockups of elements such as arsenic are being pursued for environmental reasons.This paper reviews the conditions favoured for gold agglomeration and accessibility of gold to cyanide, test conditions to achieve gold liberation and agglomeration on laboratory scale and designs that incorporate staged decomposition and roasting to make roasting a more commercial option.CITATION:Aylmore, M G and de Klerk, L W, 2013. Conditions and design considerations for maximising recoverable gold in roasting of refractory gold ores, in Proceedings World Gold 2013 , pp 375-388 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By J. W. Cunningham, M. J. Stultzman

THE demand for improved materials for high-temperature service has increased during the last few years. Iron,- nickel,- and cobalt-base alloys have been investigated extensively and many alloys with outs'tanding high-temperature strength have been developed. Considerable research has been directed toward improved methods of processing these alloys. The vacuum furnace as a tool for the purification and improved control of high-temperature alloys has been studied extensively and production units are in operation. The research covered by this paper studied the effects of casting in air, vacuum, or argon upon the elevated-temperature properties of two nickel- and two cobalt-base alloys. The alloys investigated were Stellite 31, He 1049, Udimet 500, and Guy Alloy. MELTING AND CASTING PROCEDURES Two heats of each of the four alloys under investigation were melted and investment cast under the following conditions: 1) Stellite 31 was melted and investment cast in air and in vacuum, with an argon atmosphere for pouring. 2) He 1049 was melted and investment cast in air and in vacuum, with an argon atmosphere for pouring. 3) Udimet 500 was melted and investment cast in vacuum with and without additions of zirconium and boron. 4) Guy Alloy was melted and investment cast in vacuum and in argon. The heats were all melted in induction furnaces equipped with preformed magnesia crucibles of 50-lb capacity. The air-melting furnace was powered by a spark-gap converter of 40 kw capacity. The vacuum-melting furnace was powered by a motor-generator set of 100 kw capacity. The argon heat of Guy alloy was melted in the vacuum melting furnace under an argon atmosphere. Virgin materials were used for preparing all heats except the air heats of Stellite 31 and He 1049. The charge for the air heat of Stellite 31 was a commercial blend of shot. The charge for the air heat of He 1049 was Stellite 6 shot plus those virgin materials necessary to give the desired composition. All of the materials used were of the same grade used com-

Jan 1, 1960

By G. Morin, G. Marin, M. C. Parr, J. Carignan

"Investment casting offers many advantages for the near net shape production of complex geometries, however, molten titanium reacts with most of the refractories used in investment casting shelling systems, which leads to the formation of an oxygen contaminated surface layer. This layer, called alpha case, is 0.1 to 0.6 millimeters in thickness according to the casting section size and must be removed either by mechanical or chemical milling processes. Alpha case removal processes affect casting tolerances and may contaminate the part intended for medical applications (e.g. embedding of abrasive grit media in the alloy). A shelling system based on an yttria prime slurry has been developed and was found to almost suppress the mold metal reaction. Yttria is an expensive refractory, but slurry life was found acceptable for small castings using a closed container and flow coating process instead of conventional pattern dipping. Alpha case depth has been determined for Ti6Al4V by metallographic techniques and microhardness measurements on different step block casting cross sections. Alumina and yttria second prime stuccos were evaluated in this study. The shelling system minimizes finishing operations in the production of casting for medical applications.INTRODUCTIONTitanium investment castings have been in the commercial market since the beginning of the titanium era in the mid 50’s. Investment casting is a cost effective way to produce complex parts for medical, aerospace and chemical processes applications. Investment casting of titanium is difficult due to the high reactivity of titanium with air and refractories used for shell mold building especially for the face coat. Melting is done under vacuum and no shelling system has been proven effective to suppress the mold-metal reaction yet. The main issue with the mold-metal reaction is the formation of an oxygen enriched zone at the surface of the castings named alpha case (Frueh et al., 1997; Kim, 2002; Saha, 1986). The alpha case is brittle, reduce the fatigue life in service of the parts and must be removed by chemical milling.For industrial purposes, calcia partially stabilized zirconia based slurries have become widely used in titanium investment casting for primary coats due to a combination of limited metal shell reaction. Calcia stabilized zirconia slurries have an acceptable shelf life and offer an interesting production window. Our experience shows that a resulting alpha case depth is 280 micrometers for a casting section of 6.35 mm in thickness is typical with such a shelling system (Morin, 2013)."

Jan 1, 2016

By George C. Stone

AS most of you probably know, Australia has had many strikes. The two places that had the worst reputation were the Broken Hill mines and Port Pirie, where the smelter was located. About four or five years ago, the smelter changed hands. The new proprietors - immediately endeavored to get on better terms with the men and made such progress in that respect that, the men came to them and said, "There is no use giving us any more money. You have just raised our pay one- bob a day, but the store-keeper and the boarding-house keeper have raised their prices. The boarding housekeeper raised our board three bob a week and the storekeeper took the rest of it and we are no better off." Learning that what the men needed most was firewood wood the company bought the wood on a tract of ground across Spencer's Gulf and- sent men over to cut it. The wood was brought to the works and given to a man to cut up. He thought he had an easy job and loafed, but when the committee representing the men discovered that his loafing added to the cost of 'the wood, it promptly disciplined him and made -him work as he had never worked before. The next question that arose was the distribution of the wood. The committee got bids from several cartmen whose prices varied from about two to five shillings. It gave the work to the next to the lowest bidder. The fact that if delivering the wood cost more, the user would have to pay for it, was an entirely new idea to the men.

Jan 1, 1920