Search Documents

By Kenneth G. Colman

Even though wet processes were used in coal preparation plants prior to 1941, dewatering coal was not a problem then because the finer sizes were uneconomical to recover and were considered waste. However, during the war years the scarcity of raw materials necessitated the utilization of every pound of natural resources and coal plants began seeking an economical mans of recovering fine coal. Early efforts to this end concentrated primarily on centrifugal dewatering devices. Such equipment produced good results but was relatively expensive. In 1944, a method was devised utilizing a vibrating screen fitted with a profile wire deck rather than the standard woven wire cloth deck. This machine came to be referred to as a dewaterizer. Results obtained with the dewaterizer approached those of the centrifugal equipment, but at a lower capital cost, Their use reduced either the number of centrifugal units required to follow the dewaterizers or the required energy input to heat dryers, In some cases they eliminated the need for any further dewatering equipment.

Jan 1, 1970

By Harry Perry

In the United States the state mining laws enacted in the late 1800s were the first laws to recognize that an employer had a responsibility to provide the employee a place to work that met at least some minimum safety standards. The coal mining industry was also the first major industry in the United States to be regulated in 1952 by federal safety laws, although federal inspectors had the right-of-entry as early as 1941. Within recent years, however, the Congress has enacted a number of federal safety regulations for a variety of industries, such as the Aviation Act (1958), National Traffic and Motor Vehicle Act (1966), National Gas Pipeline Act (1968), and Radiation Control for Health and Safety Act (1968). The fatality and injury experiences of the mining industry in the United States, while at a significantly higher rate than for industry as a whole, showed a continuous improvement until the last decade or two-at which time the rate leveled off. Although fatality and injury rates in foreign countries have been generally lower than in the United States, further improvement in those countries also has been difficult to achieve in recent years. It appears, therefore, that some major change in mining laws, combined with a radical improvement in mining technology and a more effective labor-management safety program, will be needed if further reductions are to be achieved in fatality and injury rates. At the same time, there is a growing awareness by society that an employee's place of work, where he spends nearly half of his waking hours, should be made as safe as possible. As increased consideration is given to means for achieving greater safety in all industrial situations, it is becoming apparent that more is required than merely providing physical safeguards on tools and machines. Rigorous, strictly enforced safety standards are useful, but more important is the desire of labor and management to make certain that industrial accidents are prevented. The pressure to achieve increased productivity, and thus receive higher wages, can be a significant deterrent to safe working practices. The temptation can be great to "take a chance" or "cut a corner" in order to speed up production. Public concern over all types of industrial safety in the United States was reflected by the introduction of a number of general occupational health and safety bills in Congress for the first time in 1968. While no legislation resulted, the hearings revealed that, although there were differences in how standards should be set and who should administer them, there was agreement on the need for adequate laws. Since the mining industry has been subject to safety standards longer than other industries, it is not surprising that advanced safety concepts for mining are being explored by the industry and the enforcing agencies. More complete and sophisticated accident reporting is being planned that will reveal the

Jan 1, 1976

By J. L. Schroeder, W. G. Talman

EXPERIENCE has shown that certain known natural conditions and other indefinite characteristics combine to make a mining area vulnerable to mountain bumps. Some of the known conditions are heavy overburden, an overlying stratum of strong non-elastic rock, a structurally strong coal seam that does not crush easily and yet is the weakest stratum in the series, and a floor stratum of more than ordinary firmness. The indefinite characteristics could include resistance of top or bottom of a coal seam to lateral flow, effect of immediate top and bottom strata, nature of the coal seam, and other factors about which very little is known. It is in this area that exhaustive study is needed to achieve positive control of the dreaded mountain bump hazard. In the Gary district, West Virginia, two of the five operating mines have areas known to be vulnerable to mountain bumps.These are the No. 2 and 6 mines, which are working the Pocahontas No. 4 coal seam. In this area the seam is overlain at a zero to 10-ft interval by the massive Eckman sandstone, which is about 100 ft thick in the vulnerable areas. Total overburden, consisting of shale, coal seams, and sandstones, ranges from 700 to 1400 ft where bumps have occurred (Fig. 1). The coal seam is 4 to 8 ft thick and has a weak columnar structure of very soft and spongy or woody coal. The immediate top is either the Eckman sandstone or hard shale, both of which provide generally good roof conditions for mining operations. The bottom ranges from medium to hard gray shale. The incidence of bumps in the Gary district dates from about 1930 and can be correlated to some degree with the increased rate of extraction attained with mechanical mining. During early years of operation at the No. 2 and 6 mines, most of the work was development and under comparatively light cover. As overburden became heavier, together with an increasing percentage of coal coming from pillar extraction, mountain bumps began to occur. Before 1945 they were much less severe than in later years, and because there were no injuries or fatalities, no records were kept. But by 1951 the incidence of bumps had increased to such extent that it became evident a mining system would have to be designed to eliminate or at least minimize these occurrences. Drawing on experience with modified versions of old systems and certain characteristics peculiar to the Pocahontas No. 4 coal seam, the district mining engineer, Martin Hayduk, outlined the essential factors for bump control in the Gary district. These control factors indicated: 1) The highly stressed area, which lies within the limits of convergence effects, moves at approximately the same rate as the retreating pillar line. 2) There is a decided softening of the periphery of blocks which is greatest and deepest on the gob side. 3) Blocks less than 45 ft wide never have been known to bump in the Pocahontas seams. Fig. 2 shows the mining plan based on these observations—a thin-pillar system with a minimum of secondary development. It was recognized from the start that the Hayduk system had certain limitations. When pillar work backed up to an inevitable surrounded block it was no longer applicable; also, burnt bottom and/or unknown factors reduced the system's effectiveness in certain headings. Since there was no way to eliminate the loaded block, it was decided to experiment with auger drilling to attain controlled release of this stored-up energy. The decision to auger was made after consideration of three separate plants, which were: 1) To cut the solid block into pillars of maximum size by driving away from the fracture line and at such a distance outby that development

Jan 1, 1959

By William D. Spielvogel

The Massachusetts Highway Department awarded the Porter Street Outfall Project to the J.M. Cashman Company in November 1991. Timely completion of the Project in one and one half years is critical to the start of the subsequent Third Harbor Tunnel North Approach project. Existing subsurface conditions and the Project's location at Boston's Logan International Airport significantly increases the difficulty of construction. The major contractual work involves relocating a reinforced concrete double box culvert supported on a continuous wood pile foundation. This existing culvert crosses and interferes with the future Third Harbor Tunnel North Approach alignment. Two parallel culverts constructed approximately 20 feet from either side of the future Third Harbor Tunnel alignment replace the existing double box culvert structure. Under the original contract design, approximately 3,100 feet of 14 ft. by 15 ft. reinforced concrete culvert is cast in place adjacent to the west side of the Third Harbor Tunnel and is located in the center of the Airport's main service roadway, Harborside Drive. This culvert is the Porter Street Combined Sewer, PSCS, which handles a combined flow of sewerage from the East Boston community and storm water runoff from Logan Airport. In addition, approximately 2,230 feet of 17 ft. by 15 ft. reinforced concrete culvert is cast in place adjacent to the east side of the Third Harbor Tunnel and is within 20 feet of an active aircraft taxiway and heliport. This culvert is the Bird Island Flats Storm Drain, BIFSD, which handles storm water runoff from the Logan Airport airfield. The existing outfall, on the west side of the Third Harbor Tunnel alignment is to remain in service and is to be connected to the new PSCS and BIFSD culverts. Therefore, a portion of the BIFSD culvert is designed as a bridge to span 128 ft. across the Third Harbor Tunnel excavation during construction.

Jan 1, 1994

By Timothy W. Beck

Roof bolter occupations in underground coal mines continue to experience overexposure to respirable dust. One potential source of dust in roof bolting operations is the exhaust from the roof bolter dust collection system. A wet exhaust conditioner (?water box?) has been developed to reduce dust emissions from the exhaust of the vacuum dust collection system on roof bolting machines. The exhaust conditioner consists of a muffler chamber and a water chamber with four internal partitions to direct airflow over the surface of the water. The National Institute for Occupational Safety and Health conducted a series of laboratory tests to assess the respirable dust capture ability of this device as compared to the standard exhaust muffler. To determine the dust collection efficiency, both devices were placed in the exhaust stream of a simulated roof bolter dust collection system. Gravimetric samplers were operated upstream and downstream of the exhaust conditioner and muffler to evaluate the ability to capture both respirable coal and limestone dust. Researchers observed a 41 percent reduction in dust concentrations for the water exhaust conditioner in the laboratory configuration. Significant levels of dust deposition in the sampling chambers may have contributed to this effective capture rate.

Jan 1, 2010

By D. Boreck

The Bureau of Mines is conducting research on the feasibility of incorporating in situ stope leaching into active underground metal mines. Stope leaching, a modified in situ leaching technique, proposes to recover metals by leaching fragmented ore in existing underground openings and collecting and processing the metal-bearing solution to recover the valuable metals. If leaching solutions escape from the stope, either through geologic discontinuities or highly permeable zones in the rock, valuable metals dissolved in the solution may be lost. Escaping solutions may also contaminate ground waters. Consequently, in fractured rock, the characteristics of the fractures in the vicinity of the leaching stope must be understood before introducing actual leach solutions into the stope. Effectively characterizing a rock mass requires the integration of several disciplines including structural geology, borehole geophysics, hydrology, geochemistry, and mining engineering. This paper will focus on the general geologic and geophysical techniques that can be used to characterize the rock mass at an underground simulated stope leaching site. The results of several geophysical logging methods, tested at the site, are compared to the geologic core descriptions. Then, the? effectiveness of the different geophysical techniques in delineating fracture zones will be assessed. Knowledge gained through the geologic and geophysical analyses can be used to supplement results from hydrologic testing. This information can also be utilized in designing blast patterns and developing strategies for controlling or blocking movement of escaping leach solutions.

Jan 1, 1991

By Harry F. Weaver

Rivers in industrial and raining areas frequently are contaminated by material dumped into them causing the water to carry in suspension large amounts of silt, which subsequently is deposited alone; the banks and, ultimately on the agricultural lands if the water is used for irrigation purposes. Two common examples of this practice are the dumping of breaker refuse in the anthracite region of Pennsylvania and the dumping of tailings from the metallurgical mills in various metal-mining districts. Studies in stream pollution and its resultant problems are very important, and surveys are constantly being made by Federal and State agencies, as well as by private companies, to determine the quantity of solids actually being carried by these watercoarses. These studies require accurate sampling of the silt-carrying water to determine the amount of solids within reasonable limits. A device that will obtain reasonably accurate samples of material from silt-bearing streams is described in this circular.

Jan 1, 1943

By A. M. T. S. Bandara

The solubility of rare earth (RE) salts in aqueous solutions depends on many factors including the type of cations and anions in solution, their concentrations, temperature and the type of solid precipitated. Experiments were conducted using anhydrous La2(SO4)3 and Ce2(SO4)3⋅8H2O as solids and lanthanum(III) perchlorate prepared by dissolving La2O3 in HClO4 solutions as RE-sources. Solutions of H2SO4, H3PO4 and their mixtures in the presence or absence of Na+, Ca2+, Fe(III) or Al(III) as perchlorates served as test solutions. Saturated solutions and precipitated solids were assayed and characterized using standard techniques to show that the La(III) and Ce(III) ions precipitate as hydrated sulphates, phosphates or double salts with sodium, depending upon the solution composition. The change in solubility of RE-salts with solution composition and temperature is the result of the composite effect of changes in solubility products (pKSP) of salts, pKa of acids and other equilibrium constants for ion-association.

By G. J. Knighton

Introduction The Sullivan concentrator treats the complex lead-zinc-iron ore from the Sullivan mine of the Consolidated Mining and Smelting Company of Canada, Limited, to make a lead and a zinc concentrate for its metallurgical plants at Trail. Three miles separate the mine and mill, which are situated near the town of Kimberley, in the East Kootenay district of British Columbia. The orebody consists typically of banded sulphides, mainly galena, sphalerite, pyrrhotite, and pyrite. Important factors in the concentration of the ore are its exceedingly complex and its high specific gravity. It should be remembered throughout the paper that results and figures are based on Consolidated's experience with the Sullivan ore. The present mill feed rate is 8,500 dry tons of ore per 24 hours, for an operating week of five and a half days. Grinding and classification of the ore are carried out in three stages and, in addition, there is a re-grind section which re-treats the zinc middling. It is the purpose of this paper to discuss the classification in the various stages and to give the results o comparative tests which have been carried out for the purpose of improving operations in the mill. The Primary stage consists of six units, each made up of a ball-mill and classifier (see accompanying flow-sheet). Four units operate in open circuit and two in closed circuit. The secondary stage consists of eight ball-mills operating in closed circuit with twenty-one classifiers. In the Tertiary stage are two ball-mills in closed circuit with eight classifiers. The re-treatment section for re-grinding the zinc middling comprises one ball-mill in closed circuit with two classifiers.

Jan 1, 1947

In 2009 Newmont Mining Corporation?s annual global spend on grinding media reached $94M USD, having doubled in the five years since 2004. The major contributing factor to the spend escalation during this period was unit consumable price, with total media consumption also rising as a function of annual ore tonnes milled. In an effort to better understand and manage the growth of this expenditure a significant supply chain management program was implemented. This was complemented by a series of technical initiatives focussed on grinding media specifications, quality management and the prediction of grinding media wear rate as a function of physical ore characteristics. This paper discusses the methodology and outcomes of these activities.

Jan 1, 2012

By S. J. Hardison

IN the fall of 1912, the appearance of water in the oil of the Nevada Petroleum Co., Coalinga, Cal., made necessary the installation of a dehydrating plant to reduce the water below the 3 per cent. limit prescribed by the agency. Unlike the mining industry, technical literature of the oil industry is limited and extremely unsatisfactory. Until the recent efforts of the Petroleum and Gas Committee of the American Institute of Mining Engineers, no concerted movement has been instituted to secure publication of papers dealing with the problems of the oil business, and because of the additional fact that dehydrating of oil has not been practiced in California to any extent up to comparatively recent time, it was found necessary to experiment in order to determine the most satisfactory plan for this purpose. It is easy to write regarding successful enterprises, but, while not so pleasant, it is equally desirable to write of failures so that others may be saved the loss incident to such investments. The water in this oil occurs both free and as an emulsion. Free water easily settles out, but the emulsion requires treatment. So far as can be determined, the emulsion consists of globules of water surrounded and enveloped by a film of, oil. Starting with this hypothesis, the theory has been evolved that in order to break up this emulsion the water must be heated at least to boiling point, when an explosion takes place destroying the globule. Unfortunately, this condition was not recognized in the installation of the first plant, which was planned on the following lines: A heater was arranged so that all the oil from the wells could be heated before reaching the shipping tanks, these being already fitted with coils for steam heating. Tanks were filled with about 4 ft. of water, live steam was turned into the coils and the water brought nearly to the boiling point, when the heated oil was run in. This for a time was partly successful, but the length of time necessary to apply this heat was too great for practical operating.

Jan 3, 1915

By Mark J. Zdunczyk

"The term “aggregate” has a number of definitions depending primarily on the use of the material. Aggregate in some context is sand, gravel, crushed stone, slag or other material of mineral composition used in bituminous and portland cement concrete, mortar, plaster, railroad ballast, filter beds and a variety of other uses where aggregates can be utilized.Of the natural aggregates, crushed stone is widely used for most construction purposes. Crushed stone can be mined from a variety of rock types such as limestone, dolomite (dolostone), granites, and granitic type rocks, basalt, gabbro (trap rock), sandstones, schist, marble, gneiss, quartzite, rhyolite, as well as other rock types. The U.S. Geological Survey (USGS) breaks down the rocks by type sold as follows: limestone, dolomite, marble, calcareous marl, shell, granite, trap rock (basalt, diorite) sandstone/quartzite, slate, volcanic cinder and scoria and miscellaneous stone.In 2015, the USGS estimates that 1.32 Gt (1.45 billion st) of crushed stone were produced in the United States. The volume of crushed stone produced, and the numerous mines that produce it make the crushed stone industry the largest mining industry in the United States. The five leading states for production of crushed stone in 2015 were Texas, Pennsylvania, Missouri, Florida and Ohio. The size of the first two states certainly helps in output because of the large market area. The remaining states benefit from being able to barge along rivers to outside markets in adjoining states. Georgia producers rail large amounts of granitic aggregate to Florida and adjacent states devoid of crushed stone aggregate, especially skid resistant aggregate (aggregate used on the top course of asphalt roads)."

Jul 1, 2016

By John C. Edwards

A fire location computational model was developed by the U.S. Bureau of Mines. The model can determine all the possible paths in a mine that smoke can travel from a fixed fire source to a smoke detector. The associated FORTRAN computer program can be utilized to determine the minimum travel time from a source fire to a smoke detector. The difference in travel time from an isolated fire source to two or more detectors can be used to isolate those airways in which the source fire is located.

Jan 1, 1990

By Dr. Kyle Perry, Ryan Sibley

Rock blasting is an inherently difficult field to quantify independent & dependent variables and the specifics of how the energy interacts with the material for a number of reasons. Independent variables such as geology are innumerable and stochastic, thus, on a laboratory and full-scale basis these variables are assumed to be homogenous across the desired rock boundary. Dependent variables are difficult to quantify in the laboratory based on the specific aspect of the fracture mechanisms that caused the fracturing. The same variables are difficult to quantify in the field because of the shear amount of material being blasted. The energy interactions with the material are difficult to quantify due to the rate of the reaction and the lack of quantification of independent variables. The second main issue with laboratory scaled rock blasting is the nature of the small form-factor explosives required for use in a scaled setting. These explosives that are utilized, traditionally PETN detonating cord, have a greater ratio of potential energy converted to shock energy rather than gas energy when compared to traditional field explosives, such as emulsion or ANFO. Research over the past decades has indicated that gas pressure has the greatest contribution to rock blasting performance, such as fragmentation and material throw. The factor of varying ratios of energy production has not been discussed in any of the reviewed publications. Publications discuss dimensionless scaling, dynamic similitude, and length-based scaling, however, none of these scaling methods discuss the ratio of energy production. The main focus will be correlation of energy production ratio of shock versus gas to dependent variables. This paper analyzes previous publications within rock blasting and related field as they pertain to scaling procedures and will highlight the similarities and differences in the various publications and detail the observed omitted variables that possibly lead to skewed data.

Jan 21, 2025

By Jameel Menashi

A process has been developed for recovering the refractory metal values contained in mixed secondary source materials such as contaminated grinding wastes, oxides and sludges. The wastes are calcined with sodium carbonate in air to convert the refractory metals to water soluble Na2CrO4, Na3V04, Na2Mo04 and Na2W04. The base metals, Fe, Ni, Co and Cu, are converted to water insoluble oxides. An aqueous leach of the calcine effectively separates the refractory metals from the insoluble base metals. Co, Ni and Cu can be recovered from the oxidic residue by conventional processing methods. The leach solution is purified and then treated to recover the refractory metals as Cr203, NH4VO3, (NH4)6Mo7024?4H2O and H2WO4. The purity of the products is sufficient for their use in many metallurgical applications. The Na+ values in the leach solution are recovered as Na2CO3(or NaHC03) and are recycled to the calcination step. It is shown that the process can accommodate a wide range of feed compositions and generates a minimum of aqueous effluents.

Jan 1, 1984

By Lee W. Abramson

Performing risk analyses on tunnel projects has become common place and on many projects it is required from an owner or regulatory perspective. After the project is planned, designed and constructed, the data concerning identified risks, assumptions, costs, probabilities and mitigations is generally long forgotten and buried in some file somewhere. A study was performed comparing predicted risks versus actual events on several recently constructed tunnel projects. Probabilities and costs for selectively common risks on tunnel projects have been studied and re-evaluated. Conclusions are presented that can guide future projects and the veracity of the tunnel risk analyses performed.

By R. B. Russell

SINCE Cahn's¹ paper on plastic deformation in orthorhombic (a) uranium an increasing amount of work is to be expected on orientation of single crystals and preferred orientation in this metal. It would seem desirable to have a table of angles between crystallographic planes (hkl) and (HKL). Table I shows these angles as distances from (loo), (0l0), and (00l), and in Fig. 1 as a standard (001) stereographic projection. Only the locations of poles whose diffracting planes produce Cu Ka reflections up to 0 = 70.5" (i.e. (154) ) are given." The relative reflection of these planes are represented by circle diameters. It is hoped that the projection may also be used in making inverse pole figures, originally suggested by Harris.' Values of 4 were calculated from the expression hH kK 1L cos = hH/a²+kK/b²-lL/c² where the lattice parameters a, b, c, and the spac-ings d were taken from the work of Jacob and Warren." (They report a = 2.852 kX (2.8578 A), b = 5.865 kX (5.8768 A), c = 4.945 kX (4.9550 A).) The parameters reported by them may be subject to revision,4,5 accordingly the interplanar angles are listed to only the nearest tenth of a degree. References ¹R. W. Cahn: Acta Metallurgica (1953) 1, p. 49. ¹G. B. Harris: Philosophical Magazine (1952) 43, p. 113. 3C. W. Jacob and B. E. Warren: Journal ACS (1937) 59, p. 2588. 4J. S. Lukesh: Acta Crystallographica (1949) 2, p. 420. ³ J. Thewlis: Nature (1951) 168, p. 198.

Jan 1, 1954

By W. R. Ingalls

THE main objective of everybody, individually and collectively as the people of nations, is to earn their living and improve the scale thereof as much and as rapidly as possible. We are able to earn" our living only by working and producing. We I are able to rise to higher standards of comfort only by increasing our production of goods, or diminishing the waste of those that we do produce, or both. This statement is trite. It is equally trite to dwell upon the importance of increased production to be derived from increased efficiency of labor and improved manage-ment; and the good results that would accrue to every-body if employers and employees would work together to secure the maximum of production at the minimum of cost. All of this is nothing more than platitude, to which every intelligent person subscribes in the abstract; but what concerns us especially, and what is neither so easy nor so understandable, is to translate the expres-sion of the abstract principle into formulas for action. The national net income obviously may be increased in two ways, or by both together. One is to diminish the waste of the goods that we already have made available. The other is to increase the supply of goods. .Increasing the supply of goods may involve the elimina-tion of waste, but a distinction is to be drawn between the waste of things that we have and the failure to obtain those that we might have. If we limit the term "waste" to the careless and profligate use of the materials that have come into our possession, together with the absorption of labor in doing obviously unnecessary things; and if we character-ize by the term "inefficiency" the failure to accomplish in our industrial operations the best of which we are capable, we shall create a distinction that will be pro-motive of clear thinking. In this paper I am going to deal with inefficiency, not waste, observing the distinc-tion, arbitrary if you please, that I have made. Without any doubt the greatest inefficiency that exists in our economic affairs is that which causes hundreds of thousands, perhaps millions, of men to be idle a good deal of the time. The major reasons for such idleness are two-fold. One of them is the conse-quence of what for convenience may be called business cycles, although I do not hold to the hypothesis of business cycles as it is now being rather widely expounded. That hypothesis involves the idea of rhyth-mic undulations due to causes unknown, but which it is hoped may be ascertained. The movement of busi-ness in waves up and down is undeniable, but that there are recurrences of cycles every so often is purely imag-inary, I think. It is unnecessary-to digress into that subject. The extents of the rises and falls above and below a median line undoubtedly is less than is commonly supposed.

Jan 3, 1922

By J. Weijdema, D. N. Dietz

In the conventional underground combustion process (dry combustion) much heat is left behind in the swept formation and goes to rva.rte. Econonmy can be improved by heat recuperation through water injection. This is most advantageous if done at the earliest opportunity before much heat is dissiputed to cap and base rock. Water injected simultaneously with the air will flash to superheated steam, which passes through the combustion front together with the nitrogen from the air. A condensation front traveling up to three times as fast as the combustion front drives out the oil. In this type of wet combustion, the water evaporates before it reaches the combustion zone. The evaporation front travels more slowly than the combustion zone. If so much water is injected that the evaporation front overrun the combustion front, combustion in that spot will be quenched and some unburned fuel will be left behind. Air reacts with the oil farther down-stream where steam temperatures occur; at steam temperature, the air reacts rapidly with the oil. Velocity of the combustion front is increased thereby and is governed essentially by the water-injection rate. In the extreme case of high water-injection rate, a short heat wave of constant length is driven through the formation by water injection. Once this wave has been established, no more heat need be generated than that required to make up the heat losses from the short heat wave; a relatively low rate of air injection will suffice. The feasibility of partially quenched combustion has been confirmed in tube experiments. A heat wave at steam temperature is observed. Chemical analyses of flue gas indicate preferential burning of hydrogen while a carbonaceous residue is left in the formation. Introduction A disadvantage of so-called dry in situ combustion is that air-compression costs are rather high. An air consumption of about 400 std cu m/cu m (400 scf/cu ft) of formation swept is an accepted figure. This high consumption is mostly wasted since much heat is left behind in the depleted oil sand. Methods were investigated for recuperating as much as possible of the heat left behind. This paper deals only with basic principles and is confined mainly to one-dimen- sional flow without lateral heat losses; experiments were conducted in relatively narrow, well insulated tubes. If some water is injected with the air, it will turn to superheated steam in an evaporation front, which should travel behind the combustion front. The steam having passed the combustion front causes a steam drive by a condensation front that can travel faster than the combustion front. The latter needs to travel only part of the distance covered by the oil-displacing condensation front, and thus consumes less air. The water-air ratio would seem limited to that at which cold water overruns the combustion. This limitation was deliberately exceeded considerably in theory and experiments. It was found that combustion is then indeed quenched, but only locally. Farther downstream, the oxygen finds residual oil at steam temperature, which is suficiently high to ensure rapid oxidation. Thus, the combustion front uses only part of the available fuel because it is chased through the formation faster than its normal velocity. No heat is left behind. This new process is called "partially quenched combustion". At the upper limit of the water-air ratio, a small heat slug is moved through the formation by the flow of water and steam. Only a small flow of air is needed since it has only to generate sufficient heat to make up for the lateral heat losses of the short heat slug. Theory Although many factors complicate underground combustion, the processes will be presented in their simplest form. For this reason, one-dimensional flow without lateral heat losses is assumed. Heat conduction in the direction of flow also is disregarded. Under these conditions, dry combustion causes very high temperatures. The heat-carrying capacity of the gas stream is small. Heat generated by oxidation of a residual oil saturation is retained in the sand. The available fuel determines the air requirement and the temperature obtained. Accepting the often-mentioned air consumption of 400 std cu m/cu m (400 scf/cu ft) formation, we calculate a temperature of the swept sand of 1,200C (2,192F) (Fig, I). If water is injected at a modest rate with the air, it will flash to superheated steam upon contact with the heated sand. One cu m (35.31 cu ft) of hot formation will evaporate about 0.5 cu m (17.66 cu ft) of water, and thereafter will accommodate (at an estimated 0.80 saturation and an assumed 0.40 porosity) another 0.3 cu m (10.59 cu ft) of water in cold condition. As long as less than 0.5 + 0.3 = 0.8 cu m (28.25 cu ft) of water is injected for every 400 std cu m (14,125 scf) of air (water-

Jan 1, 1969

By S-L. Jämsä-Jounela

Fault diagnosis systems have attracted growing interest in a number of engineering fields. The number of applications has increased and successful results have been widely reported. The fault diagnosis system presented in this paper is integrated, and it monitors the states of the process and performs fault detection and diagnosis on the process equipment. The monitoring of process states is carried out by means of Kohonen Self-Organising Maps that is a powerful tool in visualisation and analysis of high dimensional data in engineering applications. This paper presents the results of SOM analysis carried out on the Outokumpu flash smelting process. The subsystems analyzed in more detail are the condition of the concentrate burner, the condition of the gas line on the basis of the pressure distribution in the process and the cooling water circulation of the waste heat boiler, and the condition of the furnace and furnace equipment on the basis of the temperature distribution in the furnace and gas line. Keywords: Fault diagnosis, Process monitoring, Kohonen Self-Organising Maps, flash smelting

Jan 1, 2001