Search Documents

By Earnshaw Cook, H. S. Avery, J. A. Fellows

TEe increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloys presented in a companion paper. The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. The Creep Test Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test iaboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit I000-hr. tests in the temperature range of I200° to 2 200°F. with a choice of applied stress extending from jo to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10:I ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a I-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, zo per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of -construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with aludum cement; the distribution of turns is adjusted to give a maximum temperature gradient of , I°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used „ to reduce the temperature of the threaded joints and thus to facilitate removal from the grips. Thermal losses are minimized by refractory insulators cut to shape and surrounded by diatomaceous ear,th. The taps

Jan 1, 1942

By J. A. Fellows, Earnshaw Cook, H. S. Avery

TEe increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloys presented in a companion paper. The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. The Creep Test Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test iaboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit I000-hr. tests in the temperature range of I200° to 2 200°F. with a choice of applied stress extending from jo to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10:I ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a I-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, zo per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of -construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with aludum cement; the distribution of turns is adjusted to give a maximum temperature gradient of , I°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used „ to reduce the temperature of the threaded joints and thus to facilitate removal from the grips. Thermal losses are minimized by refractory insulators cut to shape and surrounded by diatomaceous ear,th. The taps

Jan 1, 1942

By Ian James McDonald

Each year, approximately 400 million tons of blast furnace slag is produced worldwide with a tapping temperature of around 1,500°C. It is normally used as a substitute for cement clinker or as an aggregate material in road construction. Currently, the slag is granulated in wet-granulation plants using large volumes of water and to date, it has not been possible to utilise the remnant heat energy of the molten slag, which amounts to approximately 1.8 GJ of energy per ton. However, in an R&D project currently underway led by Primetals Technolgies and industrial partners, a new dry atomising technology is being investigated to use air to cool molten slag and recover the lost heat energy. The resultant pelletised slag fulfils the same criteria as wet-granulated slag for use in the cement industry. Phase 1 of the project has now been completed where a technical plant was set up at the University of Leoben in 2012. A series of dry-slag granulation campaigns were carried out using remelted blast furnace slag. The elevated offgas temperatures and the quality of the slag product as verified by the FEhS Building Material Institute have shown the process suitability as an industrial application and the decision was taken to escalate the project from large laboratory scale to a full size pilot plant. The phase 2 development of this plant is now underway and is scheduled for installation at the site of an industrial partner in early 2016 where full slag flow will be fed directly to the plant from Blast Furnace ‘slag runners. This paper will show the development path taken to date and the planned route to our goal in 2016 of being the first to industrialise the ‘game changing’ process of dry Slag Granulation with Heat Recovery from the slag.

Aug 16, 2017

By H. M. Smith

Data from the Bureau of Mines routine method for the analysis of crude petroleum are used to characterize crude oils. Some data are used directly while other data are used to calculate the aromatic) naphthene) and paraffin contents of the distillation fractions and the correlation index of the paraffin-naphthene portion of the fractions. The calculated properties show significant differences in composition between crude oils. The methods of calculation and interpretation of data are explained and illustrated.

Jan 1, 1966

By J. G. Groppo, J. G. Justice, B. K. Parekh

Removal of particulates and/or metal ions from mineral/coal processing waste water is a necessity from the environmental point of view. This paper describes application of a novel AC- electrocoagulation technique to remove the particulates as well as metal ions using AC power. A series of laboratory tests conducted on a stable black water sample obtained from a sub-bitminous coal operation provided a clear supernatant (-10 NTU) from the suspension. The process also shows promise in removal of up to 90 percent of phosphate ions and other metal ions (copper and nickel) from solution. A preliminary economic evaluation of the process will also be included.

Jan 1, 1992

By Harlan W. Nelson, James B. Purdy

The great majority of stokers used in residential heating installations are of the clinkering type. Because of inherent characteristics of the underfeed combustion process as it occurs in these small stokers, and because of the wide range of operating conditions encountered in residential heating schedules, not all bituminous coals can be used successfully in residential underfeed units. The problem of providing consumer satisfaction has been attacked by the joint efforts of the stoker manufacturers and the coal industry; the stoker manufacturers have been concerned with improving their product to permit the use of a wider range of coals, and coal operators have made every effort to market selected and better prepared coals. In view of the wide range of physical characteristics and chemical properties of bituminous coals, the problems are real and are receiving increased attention. Some twelve years ago a laboratory method was developed at Battelle Memorial Institute for the relative evaluation of coals for use in residential underfeed stokers. The method was developed in conjunction with work being done at that time for Bituminous Coal Research, Inc., and for individual coal producers, to obtain information on the characteristics of coal that determined the successful performance of the small stoker. Details of the equipment and test procedure were given by R. A. Sherman1 in a paper presented at the University of Illinois Fifth Short Course in Coal Utilization. During the past several years, the evaluation of over forty different coals has been determined by investigations sponsored at Battelle by coal operators in the eastern producing districts. The purpose of this paper is to compare the results and conclusions derived from the various tests with marketing experiences of the operators, and to discuss briefly the relationship of test results to standard laboratory determinations. Equipment Used in Tests Fig 1 shows schematically the equipment used in the evaluation tests. The stoker is a commercial model of conventional design, having a nominal feed rate of 30 Ib per hr. A special laboratory furnace is used, which is tightly sealed to prevent the entrance of secondary air. The complete stoker-furnace assembly is mounted on platform scales which permits the measurement of combustible weight losses occurring during the test. The furnace stack, in which are a thermocouple, flue-gas sampling tube, and smoke meter, is connected to the laboratory exhaust breeching through a friction-less connection. Through use of an auxiliary blower system, provision is made for the measurement of the air delivered by the stoker fan to the windbox. A water seal in the duct work eliminates inter-

Jan 1, 1950

By M Bond, R R. Hargreaves, G W. Booth

There are numerous causes of speculative mineral resource and reserve inflation. Traditionally, these are linked to issues of data accuracy or misinterpretation, the use of overly optimistic estimation parameters or assumptions, an absence of independent expert verification, or the simple pressure to increase company value, covert or otherwise. Owing to its subjective nature, classification of resources and reserves remains an opaque process. Of necessity, Competent Persons rely on personal heuristic interpretations, ideally underpinned by appropriate estimation and classification experience across commodity and deposit types. Whereas independent verification of individual resource and reserve statements remains impractical, publicly available data can be interrogated for potential category inflation, particularly when viewed with exploration expenditure statistics included in annual company reports. Abrupt changes in category tonnages and market capitalisation without concomitant expenditure can aid in outlier detection. Consequently, a comparison of common exploration and resource reporting parameters offers a basis for risk assessing classification robustness, over time. In this introductory study, an analysis of globally listed companies was undertaken over a multi-year period, examining base and precious metal projects in both preproduction and operational asset classes. From these, a series of exploratory decision tree trigger points were generated against which target companies were anonymously identified and risk-ranked.

May 24, 2023

By Colin Irwin, Adrian Naranjo-Castillo, Christopher Petta, Eric Zarobila

The Shoreline Consolidation Sewer is a CSO control project in Cleveland, Ohio that requires the installation of 5,000 feet of 72-inch inside diameter pipe using microtunneling methods. After award, the contractor submitted a value engineering proposal to eliminate two deep shafts and install the tunnel in two drives instead of four. In an example of successful collaboration, owner, contractor, and engineer worked together during the initial construction stages to modify the design and update the contract documents. This paper examines the importance of exible requirements in contract documents and a collaborative environment between all parties to successfully deliver a project.

Jun 23, 2024

By N. A. Abdel-Khalek

The objective of this investigation was to compare the results of counter-current flotation column versus conventional flotation cell for the cleaning of a sulphur ore and its discrete size fractions. The tests were carried out using diesel oil as a collector and alcohol as a frother. Generally, flotation column produced concentrates of higher grade. For example, the grade of a rougher concentrate for a given feed obtained with the column increased by 33% higher than that produced with the flotation cell. Such higher grade could not be obtained using conventional cell even after 3 cleaning stages. Moreover, the column gave superior results for flotation of fine and ultrafine particles.

Jan 1, 1991

By B. Mishra

Several reactive metal purification processes using molten salts generate effluent from which significant quantities of metal can be recovered prior to discardinglrecycling the salt. A Salt-scrub [SS] process has been applied where the reactive metals are recovered as a metal-gallium alloy by calciothermic reduction of the metal compounds. The SS alloy compositions were produced by mixing, pressing and sintering the metal-powders. Measurement of metal recovery has been studied for cerium, silver, tin and lead. The process has been optimized for variables such as the metal quantity per kg of effluent salt, amount of excess calcium over stoichiometry, stirring rate and time and holding time at reduction temperature. Over ninety-seven percent metal recovery has been obtained under optimized conditions. The development of an alloy for efficient Salt Scrub processing reduces a major contaminated waste disposal problem as well as recovering the valuable reactive metal. Surrogate metals have been used in this work to study the behavior of plutonium.

Jan 1, 1994

By R. Kramer

During foundry sand reclamation process development, molds formed from reclaimed chromite sand showed a rapid decline in tensile strength during thermal cycling tests. Because this characteristic could limit reuse of chromite sand in the. foundry, the sand was examined in detail Scanning electron microscopy, x-ray mapping, magnetic susceptibility, and x-ray diffraction were utilized to evaluate processed chromite sand. It was found that process variables such as binder composition, reclamation temperature, and processing method had a significant effect on the chromite sand particle surface. X-ray diffraction indicated a crystallographic change in the processed sands. Magnetic susceptibility also increased after processing. Diffusion of iron to the particle surface and increased surface roughness were identified as potential causes of the decreased tensile strength in the molds.

Jan 1, 1991

Heap leaching has become one of the prime technologies used for the recovery of precious metals from low-grade ores over the past ten years. The recovery process involves mining and stacking the ore on engineered leach pads, with or without crushing and/or agglomeration, followed by leaching with a low concentration sodium cyanide solution. The metal-bearing, pregnant solution is then processed by zinc precipitation or activated carbon absorption to extract the precious metals. The leaching process continues until all economic metal values are removed at which time the spent heap leach pads, the leached materials and excess process solutions require decommissioning. The management of these solutions may present a potential challenge for successful and environmentally sound decommissioning due to their composition, volume or continuity of generation from the spent ore even though active leaching has been terminated. The principal objectives of solution management in decommissioning spent heap leach pads are to meet all operative environmental regulations in a cost-effective manner and to leave the pads in a condition where they do not present a long-term liability either to the operator or to the environment. This involves the reduction in volume of the residual process solutions and/or treatment of these solutions to where they meet applicable water quality criteria. In the past, the environmental and economic aspects of decommissioning and solution management have been overlooked or under-estimated during the planning of mining operations. As a result, there is a potential for long-term liabilities and costs to be recognized only at the end of active leaching, a time at which operating revenues and cash-flow are minimal. Therefore, the decommissioning process requires addressing at the mine planning stage and agencies now require that a plan for solution management after the cessation of operations be submitted prior to initiation of mining. This paper discusses aspects of process solution management during decommissioning, both in terms of quantity and quality, and how potential issues may be recognized and planned for in the initial stages of heap leach design.

Jan 1, 1992

By Gerrit V. R. Goodman, Fred N. Kissell

The Bureau of Mines has evaluated the effectiveness of the safety elements used to prevent tunnel methane explosions. These fa1l under the general categories of better ventilation, better gas monitoring, reducing ignition sources, and improved worker training. For this evaluation, a technique called fault-tree analysis was used to analyze questionnaire responses from 27 tunneling experts. This analysis allowed us to rank the effectiveness of each safety element, and indicates where money is best spent to reduce the chance of a methane explosion. Results indicated that large decreases in the explosion hazard only take place with the simultaneous application of several elements. Most of these involve a human component - the everyday vigilance and awareness of those working underground.

Jan 1, 1991

By James G. Lyons

All machines vibrate and make noise. An increase signals impending trouble. Vibration and noise analysis allows the condition of the machine to be determined without costly interruption in service for disassembly and physical inspection.

Jan 1, 1977

By H. G. Hedlund

Tailings in Mining Industry can be handled in different ways. Today tailings disposal is in focus by projecting new plants as well as treating and handling of old Tailings dams.The trend today is to process minerals, detoxify the Tailings and place them as dry surface Deposition or Underground Backfill. This paper will briefly present five different Mining plants in North and Central America, where Tailings have to be dewatered for dry depositing. The Metso-Sala VPA is a filter especially developed for dewatering and drying of Mineral Concentrate and Mineral Tailings. Keywords: tailings disposal, dewatering, drying, mineral tailings

Sep 1, 2012

By G. H. Gilman

The campaign now being waged to improve the quality of the rock-drill bit is the natural outcome of the scientific development of the drilling machine during the past twenty years. In this development there has been a great increase of power output per unit of weight of machine. But the development of the rock drilling engine has been seriously hampered by the need of a drill bit that would withstand, without undue wear or breakage, the heavy rapid blows of the improved pneumatic hammer. This problem was difficult to solve because an increase in the weight or section of the drill-steel bar resulted in decreased cutting speed and higher operating costs of both the bit and its actuating engine. The solution, therefore, is to make the bit of steel that, for a given weight or section, will be more shock and wear resisting. In the attempt to meet these requirements, many of the drill-steel manufacturers alloyed the steel with vanadium, chromium, nickel, etc. on the assumption that such elements would improve the rock-drill bit but due to the sensitiveness of such steel to forging and heat treatment, higher cost, and lack of continuity of effort on the part of the steel manufacturer to perfect this product, but little progress has been made in the adoption of these steels and the so-called straight carbon steel is today recognized as the standard material for all rock-drill bits. The first step in improving drill-bit efficiency is the determination of the cause of breakage and wear. For this reason, in 1917, certain rock-drill manufacturers, in conjunction with some of the larger mining interests, conducted exhaustive tests in both the field and the laboratory. It was then found that, in the main, the cause of drill-steel troubles is not attributable to the duty imposed upon it by the normal operation of the drilling engine, but to improper forging and heat treating of the bit and to the subjecting of the bit to improper use. The fact that it is possible to minimize the troubles attributable to improper heat treatment of the drill steel has been demonstrated and it is recommended that such knowledge be made available by teaching those interested in the production, use, and up-keep of drill bits the principles on which success in this direction may be achieved. Unfortunately, but little attention has been given to the education of the drill smith. But a few years ago, the instructions given the man

Jan 1, 1922

By George S. Rice, J. W. Paul, E. H. Denny

Data assembled by the Bureau of Mines , coupled with requests from coal companies , have emphasized the desirability of establishing standardized specifications for brattice cloth with particular respect to durability and fireproofing . Brattice cloth is a canvas or other material , often covered with some fireproofing composition , which is used extensively in coal mining for temporarily deflecting air into pillar workings and maintaining ventilation at the working faces . These specifications will be established , it is planned , through a cooperative program in which the U. S. Bureau of Standards will make a series of tests of various brattice cloths treated with respect to fire- resisting qualities and the U. S. Bureau of Mines will continue to assemble field data on the use of brattice cloth . Plans now are being made for this cooperative work. Without attempting to make a complete survey , the Bureau of Mines has made preliminary studies and investigations , and verious representative coal - mining companies have furnished detailed information . The information thus gained will be used as the basis for the cooperative investigation , but the Bureau of Mines would welcome additional information from mine operators on the character and weight of brattice cloth , conditions of use , durability , quantity employed and price . Such information should be sent to the Director , Bureau of Mines , Washington , D. C. The mine operator is interested in procuring at reasonable cost a brattice cloth with lasting fireproofing quality and of as great durability and strength as possible . There has been a lack of assembled data and knowledge regarding the subject , but the Bureau of Mines feels that this lack of knowledge may be overcome if the coal -mining companies will lend their hearty support to the cooperative investigation and submit information relative to the use of brattice cloth in their own properties . Information contained in this report is based on data obtained from coal operators in bituminous districts of Pennsylvania , Alabama , Utah , Indiana , Illinois , Colorado and Nova Scotia .

Feb 1, 1923

By P. P. Gregory

ESTIMATION of re- serves in prorated sand fields has been discussed by S. A. Judson, H. D. Easton, Jr., and W. A. Schaeffer, Jr., in a paper that appears in Vol. 114 (1935), of the A.I.M.E. TRANSACTIONS. The purpose of this present paper is to extend the investigation to prorated flush limestone fields and to outline a method of procedure in determining the amount of oil originally in place and the amount of oil that can be recovered from such fields. Although it is possible to use the decline curves to estimate the amount of recoverable oil in certain limestone fields that are allowed to produce the oil at or near capacity production, such a method cannot be used in fields under severely restricted production rates. The problem is exceedingly complex due to fluctuation in the allowable rates of oil production over a wide range and at frequent intervals, and especially because of the heterogeneous nature of the reservoir itself. A well completed in a large solution cavity, capable of producing great quantities of oil per day, may be offset by a well of very limited capacity. Also, it is di5cult to arrive at an average figure for porosity in a given limestone reservoir due to abrupt variations in the character of limestone, in many instances even between two ad- joining wells. It is a safe statement that uniformity of porosity and permeability in limestone reservoirs .is nonexistent. It is evident, therefore, that the method of estimation of re- serves on the basis of per-acre content can give only approximate results.

Jan 1, 1935

By Y. Zedan

In this study, the statistical design of experiments (DOE) was applied to study and regulate the properties of near-eutectic Al-11%Si alloys. Develop regression equations for such response variables as hardness, yield stress, ultimate tensile stress, percent elongation, total cutting force, cutting power, and tool life together with other factors which, include the percentage composition of the alloying elements, and the requisite modification (Sr) level. These equations may be analyzed quantitatively to acquire an understating of the effects which the main variables and their interactions may have on the mechanical behaviour and the machinability of the alloy under investigation. The results reveal that increasing the levels of Cu and Fe content results in an increase in hardness, yield stress, and ultimate tensile strength in both modified and non-modified alloys. On the other hand, both Cu and Fe appear to affect the percentage elongation adversely, whereas the Sr-level has a positive effect on this parameter. It was found that Sr-levels have the most significant effect on the cutting forces and cutting power followed by the content in Fe and Cu. The results also reveal that the interaction coefficients of these variables have a significant effect on tool life compared to the main independent variables. This fact may be attributed to the formation of complex insoluble phases between Cu, Fe, Si, and Al as investigated using Scanning Electron Microscopy (SEM) attached to an EDX analysis system. The accuracy of the regression equations in predicting the expected properties has been verified by carrying out random experiments in the range of variation of these variables.

Jan 1, 2011

By Pefer F. Stacey

This paper considers some of the trends in slope design technology that are emerging as we approach the 21st Century. While the ability to design stable slopes has unproved greatly over the past 20 years, trends towards steep short-term slopes for small highgrade orebodies, and very high slopes for mega-pits centered on low grade deposits are starting to indicate limitations in available technology.

Jan 1, 1994