Search Documents

By J. S. Lee, R. K. Massarsch

"A 3.2 km long immersed road tunnel forms part of the Busan-Geoje Fixed Link in South Korea, which connects Korea's second largest city Busan, with the island of Geoje. To ensure the water tightness of the joints of the segmental tunnel structure and to limit the forces in the shear keys, the differential settlements have to be limited. This was achieved by extensive soil improvement of the marine clay below the tunnel with cement deep mixing (CDM) and sand compaction piles (SCP). This paper focuses on the characteristics of the marine clay, the basic design principles, layout and constructional issues of the CDM soil improvement, and numerical and numerical analyses to predict settlement and stability.INTRODUCTIONThe Busan-Geoje Fixed Link consists of two short cut & cover tunnel access ramps, a 3.2 km long immersed tunnel (Figure 1) and two long span cable stayed bridges. The tunnel consists of eighteen concrete elements each of 180 m length having a rectangular cross section of 26.5 m in width and 10 m in height. The tunnel elements are cast in a dry dock on shore and floated out to the sea, immersed in their final positions on a gravel bed in pre-excavated trench and connected to each other by a dual gasket system. The water depth was up to 50 m making the tunnel of the deepest yet constructed. After immersion, the tunnel is protected by backfill material at the sides and rock armour on top. Each tunnel element consists of eight 22.5 m long segments. The joints between the segments and between the tunnel elements are equipped with EDPM water stops, Omega seals and concrete shear keys. The longitudinal displacement behaviour of the segmental tunnel structure in the varying ground conditions represents a complex soil-structure interaction problem which has been modelled with a FEM structural model representing the tunnel, the joints and with springs to represent the soil that are derived from the PLAXIS soil/foundation models. In order to ensure the water tightness of the joints which have limited opening capacity and to limit the forces in the shear keys, differential longitudinal settlements have to be limited. This is achieved by limiting the variations in subgrade modulus along the alignment and it in practice means that differential settlements are limited to a few tens of millimetres. Without soil improvement of the marine clay below the tunnel, long-term tunnel settlements of up to 400 mm were predicted when taking into account the likely variations in the trench profile, backfilling and uncertainties in the soil properties. Such large total settlements led to large variations in the sub-grade reaction along the alignment, which in turn resulted in significant differential settlements, unacceptable joint opening and large shear key loading. It was therefore decided to carry out extensive soil improvement with cement deep mixing (CDM) (CDIT, 1999) and sand compaction piles (SCP) (Kitazume, 2005) after studying a number of foundation alternatives."

Jan 1, 2015

By N. Aouad

Dump truck operators are exposed to whole-body vibration (WBV) levels that exceed the International Standard Organization (ISO) 2631-1. The WBV level measured by RMS acceleration value, for operator comfort, and long-term health and safety is under 0.315 m/s2 by these standards. However, fundamental research by Frimpong and Aouad (2009, 2012) and field experimental study by Kumar (1999) have shown that operators are exposed to extreme WBV levels exposing them to injuries and musculoskeletal diseases in the long-term. These extreme WBV values in the vertical direction are equal to 3.56 m/s2, 1.12 m/s2 and 0.87 m/s2 for the operator?s seat, lower-back and cervical regions, respectively. This paper will outline current research to solve these problems. Keywords: WBV, Truck Vibrations, MSC.ADAMS, Virtual Prototyping

Feb 27, 2013

By P. Hr?enjak

Two groups of methods are usually used in design procedures of underground excavation of dimension stone: the analytical and numerical methods of analysis. In all of these methods the in situ rock mass strength represents the main problem. This is due to massive rocks in dimension stone deposits, consisting of large blocks of rock separated with particular discontinuities, for which the Hoek-Brown empirical criterion, developed for jointed rock masses, cannot be realistically used to estimate rock mass strength, especially for a particular block of rock mass or a particular pillar. On the basis of the regular underground excavation process of dimension stone by separating blocks with the flat jack application, we developed the in situ flexural strength testing method. We carried out numerical analyses and evaluation of uncertainty of measurement in order to validate the in situ flexural strength testing method. On the basis of very good validation results, as well as results of the in situ flexural strength testing of exploitable layers on the ?Kanfanar? quarry, we introduced a new coefficient of reduction, which can be used for correction of other strength parameters determined by laboratory testing for obtaining a realistic value of rock mass strength.

Aug 1, 2013

By M. L. Lissberger

entirely suitable for certain uses and even possess advantages over present solders at high temperatures, but they are certainly not suitable for all uses. However, it is conceivable that their use in many places will effect a material conservation of tin. It will probably be wiser to use cadmium in solders where good results have been obtained than in brass where this element will be a source of possible trouble. F. F. Colcord,* New York, N. Y.-—The cadmium-lead solder has a higher conductivity than the lead-tin alloy, which ought to make it advantageous in the manufacture of electrical machinery. In the case of solder for tin-can work, one of the high officials of the American Can Co. said that he fully intended to .give it a good trial, and I do not believe they are going to reach hasty conclusions and run the risk of poisoning the public. Solder, Its Use and Abuse Milton L. LissbeRgeR,† New York, N. Y.—Solder is a mechanical mixture of tin and lead, a fact which is susceptible of very simple demonstration. A bar of solder of a grade even as low as 30 per cent. tin and 70 per cent. lead, passed through a buffing machine, will show a surface practically identical with that of a bar of second-quality or reclaimed tin. The buffings, on chemical analysis, will prove to be almost pure lead. According to the best practice, solder is made in the following manner. Virgin pig lead is first melted, and when it is thoroughly liquefied, virgin pig tin is added, together with a small amount of flux; the latter is for the purpose of bringing to the surface the so-called "liver," consisting of impurities that may have remained in either the lead or the tin as a result of incomplete refining. The combined material, when completely liquid, is thoroughly stirred for some hours, and is then cast into small pigs. Just before casting, and continuously during this operation, the molten metal yields dross, consisting largely of the oxides of lead and tin; this should be carefully skimmed off. After the pigs have cooled, they are taken to a smaller kettle, re-melted, and cast into the desired shape for use; or if wires, ribbons, etc., are to be made, the solder is cast into slugs suitable for extrusion and rolling. During this second operation, the skimming of dross should be even more carefully done than at first. Hand mixing has proved to be the only reliable method for the production of the best quality of solder, irrespective of its percentages of lead and tin. The best quality of solder is not necessarily that which contains the highest percentage of tin, but rather is that composition which performs best on the required piece of work. In order to produce

Jan 1, 1919

By G M. Volkmann

Pipe umbrella support systems – also called canopy tube systems – have been used successfully for tunnelling in challenging ground conditions since the 1970s. Historically, the drilling unit was the limiting factor for pipe umbrella installations – less attention has been paid to pipe couplings and their influence on labour time and load-bearing capacity.This contribution investigates the influence of the type of pipe connection on the load bearing characteristics of a connected pipe and discusses associated influences on design calculations and installation performance. Standard thread connections reduce the effective cross-section and thereby load-bearing capacity in the connection area. To achieve design parameters, over-dimensioning of the un-weakened pipe section is the only way to overcome this limitation. Recently, two new, alternative connection types were designed and developed for connected pipe umbrella pipes. The first one is the nipple coupling, consisting of fitting with a threaded connection that is pressed and welded into the ends of standard tubes. The second type is the squeezed connection, which mechanically connects non-threaded pipe ends, achieved by force-fitted squeezing from the drill rig. Both coupling types have technical as well as operational advantages compared to the common thread couplings, which are the weakest point in the support system.In the following sections significant technical differences are explained, design values given and a site example presented to illustrate the operational advantages of the newly developed coupling?type.CITATION:Volkmann, G M, 2014. Development of state-of-the-art connection types for pipe umbrella support systems, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 333–338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The development of 3D multi-parametric models facilitate the provision of resource information well in advance of the mining face. Using the model, one can evaluate mining areas not only for grade and tonnage predictions but also for predictions of rock mass quality. Blast design and milling requirements can be derived from the rock mass quality predictions. This information can be used for overall mine planning and evaluation, costing, production optimization and slope design. This allows the full range of mining activities and costs to be interconnected, thereby lowering costs and improving efficiencies through the application of the multi-parametric model. Feasibility studies for new projects require an expected budget expenditure estimate to within 5% of actual costs. This level of accuracy is expected by mining companies and investors but cannot be achieved without a sound knowledge of the rock mass variability. By developing a 3D multi-parametric model as part of the feasibility study and using the same geological model exploration boreholes, a significantly better understanding of the rock mass conditions can be obtained. This rock mass information can be used for equipment selection, economic pit layouts, processing plant design, underground mining layouts and support requirements, to name but a few design parameters that depend on rock mass conditions. The initiative at Anglo Platinums, Potgietersrust Platinum Ltd.?s (PPRust) operation, has delivered significant results showing improvements across the mine to mill value chain. These include increased loading rates, reduced electricity and crushing consumables, as well as higher plant throughput. The ore reserve model has gained international acceptance as an invaluable tool for a mining operation. Certainly most financial organizations will not invest in a mining project that does not have an ore reserve model. There is the potential for multi-parametric models to be recognized as vital tools in the mining process, as is the case with ore reserve models.

Jan 1, 2007

By Roger Storry, Donald Bruce, Arnaud Hochart

"INTRODUCTIONThe Port of Miami Tunnel (POMT), designed and constructed by Bouygues Civil Works Florida between 2009 and 2014, was a Public Private Partnership between the Miami Access Tunnel Concessionaire, Florida Department of Transport, Miami-Dade County and the City of Miami. The project comprises dual 11.3m internal diameter, 1.27km long, twin lane road tunnels running between Watson and Dodge islands and under the main shipping channel in Biscayne Bay (Figure 1).The POMT was a unique project which embodied many technical firsts and involved the first large diameter tunnels constructed through Florida’s challenging sedimentary carbonate strata. At the outset, a comprehensive ground investigation was performed, using both conventional and less conventional investigation techniques, to characterise the highly heterogeneous ground conditions.The findings of the investigation had a major impact on the tunnelling methods, triggering a series of mitigation works to ensure that the tunnels could be excavated safely and effectively. The mitigations included modifications to the already designed Tunnel Boring Machine (TBM), to facilitate an innovative excavation process, and a unique grouting campaign (Storry et. al. 2013a). The project was completed and opened to traffic in August, 2014 and has significantly alleviated traffic congestion in Downtown Miami.GEOLOGICAL CONTEXTThe geological conditions at the project site consist of carbonate sediments which can be divided into distinct geologic units; the Miami Limestone Formation (Layers S3, S4), the Fort Thompson Formation (Layer S5), the Anastasia Formation (Layer S6), the Key Largo Formation (Layer S7) and the Tamiami Formation (Layer S8). Multiple changes in sea level over a relatively short geologic time scale have resulted in a heterogeneous profile consisting of interbedded sedimentary rocks and sediments, which vary widely, both vertically and laterally (Figure 2)."

Jan 1, 2016

By Steve Colburn

The CRITERION Survey Systems utilize both theodolite mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environments characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, Windows-based, interactive software program which can be run on any standard PC.

Jan 1, 1997

By William R. Kohl, Craig B. Clemmens

"Since 2010, North Central Resources, Bridgeport, WV, has been using the sonic log to estimate the rockmechanics properties of the coal and adjacent strata in their exploration drilling program. In 68 out of the 85 boreholes they have drilled since 2010, they have conducted shear wave analysis on sonic logs run in these boreholes. By incorporating the rock mechanics logs into the geological model of the coal seam, the engineers can develop a better understanding of the support requirements for the mine.WellCAD Borehole processing software provides vastly improved efficiency in analyzing shear waves from borehole sonic data than previously available methods. The calculation of most rock mechanics parameters requires knowledge of the density and both the compressional wave velocity and the shear wave velocity. Density logs are well known and an industry standard. Sonic logging is equally well known, although less frequently used, as an accurate source of compressional wave velocity. Shear wave velocity is difficult to measure in a geophysical log, but can be estimated from digitally recorded wave form records. This is a time consuming manual procedure which requires the visual examination of thousands of individual wave forms.WellCAD allows the viewing all the wave forms on a VDL display. The observer can create a pair of false logs by manually tracing the interference points on the display for each receiver. He can check himself by observing wave forms in the traditional format. He can then create a shear wave transit time log or “Delta-S” log by subtracting the false log from the near receiver from that of the far receiver. This can be plugged into standard formulae to generate curves for most standard rock mechanic parameters, including bulk modulus, shear modulus, Young’s modulus, and Poisson’s ratio.While these parameters do not entirely substitute for destructive testing, they are extremely cost effective. An entire borehole can be analyzed for the cost of a single destructive test. This allows for a more judicious use of destructive testing while permitting the extension of test data into the rock mass with much greater confidence."

Jan 1, 2015

By A. E. M. Warner

In co Limited has long and extensive experience in converting nickel-copper primary smelting mattes over a broad range of nickel/copper weight ratios and combined nickel-copper-cobalt contents. At the Copper Cliff Smelter, the composition of the converter product matte has to meet the requirements of the matte separation process; at the Thompson Smelter, converter matte of a different composition is cast into anodes for nickel electrorefining; and in Soroako, Indonesia, a very low copper product matte is granulated for the Japanese market. Recently, Inco has conducted pilot plant testing of three possible nickel-copper matte continuous converting routes, namely flash converting, oxygen top blowing-nitrogen bottom stirring, and tuyere blowing. This test work has generated substantial new information on nickel-copper matte converting chemistry. This overview paper reviews the metallurgy of nickel-copper matte converting, in particular the behaviour of cobalt and the operating conditions required to meet the iron and sulfur specifications of the product matte. The relevant thermodynamic information is used to discuss the industrial data.

Jan 1, 2003

By N. Arbiter, C. C. Harris

In 1961, a research program started at Columbia into the mechanical aspects of flotation,* and certain ends are now in view. The purpose of this note is to explain these tentative conclusions in the hope of stimulating discussion and eliciting new data, especially industrial data, with which to test the views expressed. The variables presently under consideration are impeller rotational speed, N, volumetric air rate, Q, and impeller diameter, D, the latter being the parameter chosen to designate cell size. The most favorable *The latest work 1 references all previous publications. chemical environment is not under discussion since the procedures for establishing it are better understood than those for optimizing N and Q by virtue of a longer history of more intensive investigation. THE GRADE AND RECOVERY SURFACES With a given ore, chemical treatment, and flotation machine, both grade, G, and recovery, R, are functions of N and Q. The GNQ and RNQ relationships are best viewed in terms of three-dimensional surfaces (Fig. 1) which are experimentally determinate.2 TO maintain grade at an acceptably high level, it is necessary for N and Q to lie within certain limits, and similarly with recovery. However, the ranges of N and Q for grade on the one hand and recovery on the other are rarely the same. Selecting the single N

Jan 1, 1970

By Thomas C. Wilder

The concentration and activity of oxygen in liquid copper has been measured by the reversible galvanic cell: at 1100°and 1200°C for the concentration range of oxygen of 3 to 5600 ppm Measurements for approximately thirly alloys at each temperature indicate that the activity of oxygen roughly follows Henry's law, the activity coefficients of oxygen being 0.12 and 0.205 at 1100° and 1200°C, respectively. These results compare javorably with the results of seven other electrochemical and gaseous equilibrium studies on this system, the free energy of the solution reaction 1/2 O2 = O (7 at. pct in Cu, liq) being -18.10 * 0.30 kcal per gfw at 1200°C. Estimates of the standard molar free energy of formation of CupO(S) are also made. Praclicul consideration of this cell as an oxygen sensor for liquid metals is discussed briefly. SOLID mixed-oxide electrolytes which have a defect structure in the anion sublattice have recently become a very popular means by which the chemical potential of oxygen is measured at high temperatures. Since the pioneering work of Kiukkola and Wagner1 such electrolytes have been used in numerous cell studies for determining the thermodynamic properties of metallic oxides and oxy compounds, the partial pressure of oxygen in vacuum systems and other atmospheres, and the properties of oxygen dissolved in metals and alloys. The use of a solid electrolyte in a cell for a fast reliable method of oxygen determination in liquid metals would be a very important tool to the process metallurgist. In copper, for example, the oxygen content of the molten metal in the cathode furnace is a prime factor in determining the "set" or solidification profile of cast wire bars. In this investigation the activity of oxygen in liquid copper was measured by an electrochemical cell employing the electrolyte ZrO2 + 7 1/2 wt pct CaO. The cell used at 1100° and 1200°C was

Jan 1, 1967

By Terrence J. Stobbe

On the job injuries to the musculoskeletal system are probably the oldest of the industrial safety problems. Long before we had pinchpoints to guard, chemical vapors to ventilate, and noise to enclose, people were getting strains, sprains, and sore backs from their work activities. In spite of the age of the problem, it remains a long way from being solved. The past ten years have seen a significant commitment by the sci¬entific community to understanding the problem. Engineers, scientists, doctors, and epidemi¬ologists have been involved, and as a result, today we have a much better understanding of the problem. The first step in understanding a problem such as this is to explore its history and epidemiology. The research done by Chaffin (1977), Snook (1970), Ayoub (1978), the ILO (1962), and others, led NIOSH to publish its Work Practices Guide for Manual Lifting in 1981. The guide was based on research carried out in general industry, but subsequent research by Stobbe (1983) and Peters (1983) has suggested that the nature of the problems producing injuries in underground mining is the same as in general industry. The problems are more intense in the mining environment.

Jan 1, 1984

By Yafei Xiong, Yue Wang, Guotao Xu, Shuzhong Li, Huaiyuan Li

"The composition, properties and structure of taphole clay with high strength and friendly surrounding used in a new blast furnace with 3800 M3 volume was studied. The developed taphole clay had been applied in the blast furnace for four months, pouring times were 11-13 every day, flowing rate of hot iron was 7.5 t/min and the consumption of taphole clay was 0.49Kg per ton iron, which can make the new blast furnace attach the designed production quickly and decrease the cost of hot iron. The taphole clay is easy to be opened in the channel of hot iron which can be remained in stable shape under the corrosion of slag or hot iron, and it dose not produce poisonous smoke in yellow or dark color in the use process. The development of new taphole clay is useful to improve the work surrounding of the blast furnace.IntroductionIn the iron-making process, the taphole clay's function is filling up the taphole and protecting the formation as well as the growth of the clay in the blast furnace, maintaining the enough taphole depth; simultaneously it is easily to open a hole and knock out the clay. The taphole clay has a good performance of molten slag and hot iron resistance. The traditional taphole clay uses coal tar or carbolineum as a binder, and the performance of taphole clay is good, but it has the black and yellow poisonous smoke, which is harmful for work condition. Through the investigation on the binder's composition and poisonous performance of taphole clay, the environmental taphole clay is developed by some foreign companies, which is named the third generation product with benzene is less than 300ppm, and it has been used in European steel companies. This application of the taphole clay with high strength and environment-friendly using in 3800m3 blast furnace is introduced and the performance is discussed and analyzed in this paper."

Jan 1, 2012

By W. T. Sampson

Introduction The Kirkland Lake (Ontario) property of Wright-Hargreaves Mines, Limited, - consists of four claims. The two main shear zones or 'breaks' of the Kirkland Lake camp extend through three of these claims, for a distance of approximately 3,500 feet. These claims are on the northeast side of the original lake. The water in this section of the lake has now been replaced with mill tailings. The degree of success of any completed undertaking, especially in the mining industry, reflects the personnel involved. I state with pleasure that the successful deepening of No. 5 winze from 6,400 feet to 7,272 feet was largely due to the co-operation and skilled workmanship of Shaft Captain J. Myelde and his efficient 'leaders'. This winze was sunk at a time when it was most difficult to obtain experienced shaftmen, with the result that the crews did not wholly consist of experienced men (although their desire to learn shaft sinking soon gave good results). This condition added greatly to the responsibilities and duties of those in charge, whose first consideration was for the safety of those engaged in the work, and I take great pride in recording that the entire sinking programme was completed without a lost-time accident. Location of Winze Due to the information obtained through deep diamond-drill holes collared below the 6,000-foot level being of sufficient importance to warrant further exploration, it was decided to deepen the existing No. 5 winze rather than sink another winze. This decision meant that the sinking must be co-ordinated with and proceed simultaneously with operations in the winze, where mining was being carried on between the 3,900-foot and 5,100-foot horizons, inclusive.

Jan 1, 1948

By G. Venkateswara Rao

The multi-gravity separator (MGS) is a novel piece of equipment for the separation of fine and ultra-fine minerals. However, the published literature does not demonstrate its use in the separation of Iron ore fines. Therefore, an attempt was made to study the effects of different process variables on the performance of an MGS for the beneficiation of Iron ore fines. The results obtained from this study revealed that among the parameters studied, drum rotation, amount of wash water and angle of inclination play dominating roles in controlling the yield and grade of the Iron ore. The majority of the newly developed Multi gravity concentrators have tremendous potentials for various applications. Therefore, the performance evaluation of these concentrators treating various minerals, coals, heavy metal recovery from tailing dams, etc., have become an active research topic. Several attempts have also been made to develop appropriate mathematical models of individual concentrators. Despite all these efforts, these concentrators have yet to find the widespread applications they deserve. The ?as received? sample assayed 40.80% Fe, 40.90% SiO2,0.24% Al2O3and 0.20 % LOI and all other trace elements within the specified range. The current paper deals with the Mineralogical studies, characterization and process amenability studies of Sub grade Iron ore from Deposit No. 5, Bacheli complex of Bailadila using Multi Gravity Separator (MGS).

Sep 1, 2012

A system to continuously measure the concentration of radon in mine ventilating air has been developed and tested in a uranium mine. In use, the air/radon mixture to be monitored is pumped through filters into a scintillation cell where nuclear decay of the radon produces flashes of light. These are electronically counted, giving a quantitative measure of the radon present. Air is continuously drawn from the mine atmosphere into the radon sensor box. This air sample passes through two filters into the detector cell as shown in the schematic diagram. A portion of the radon in the detector cell will experience nuclear decay, producing polomium 218 and an alpha particle. The alpha particles from the fraction that decays strike a zinc-sulfide coating on the inside wall of the cell and produce flashes of light. These enter a photo-multiplier tube which records each flash as an electrical pulse. An amplifier increases the voltage of each pulse, allowing electronic screening to remove noise and other undesirable pulses. The remaining pulses are counted by a conventional data acquisition system.

Jan 1, 1978

By J. C. Bradley

The relation of annealing temperature to conductivity of copper wire has been determined. Conductivity hard was 98.26 per cent. After a 10-min. heat,ing at 200" C. it was 98.69. By annealing 10 min. at 300" C. a large increase, to 100.93, occurred. Maximum conductivity, 101.15, was attained after a 500" C. anneal; thereafter it decreased to 100.53 after a 950" C. anneal. If copper is gassed the decrease is much more than this. Material and Method The work was done on high grade electrolytic copper, 99.942 per cent, copper plus silver, silver 0.0008 per cent. It was hot-rolled to 1/4 in., then cold drawn to 0.080 in. The wire was cut into 25 5-ft. lengths and numbered 1 to 25 as cut. Four samples were tested hard. The others were wound into 5-in. diameter coils. For the 100" C. heating a coil was put into water, the water brought to . boiling, and the wire kept at this temperature for 10 min. For the higher temperatures the coils were placed in envelopes of sheet copper, a little water added, and the envelopes sealed by folding over the edges twice, and hammering them together. This kept the air out very well. The envelope and wire were brought to the desired temperature; this was maintained for 10 min., then the whole was water-quenched. Results Data from the tests are shown in the table and plot (see Fig. 1); conductivity is referred to the International Annealed Copper Standard at 20" C. Conductivity hard is considerably less than conductivity soft.1 The increase is sharp when the wire anneals. The maximum, 101.15 per cent, in the particular material used, comes at 500º C.; thereafter the conductivity falls to 100.53 per cent. after 950" C. annealing, a drop of 0.62 per cent.

Jan 1, 1927

By G Richmond, J R. Glen

Western Metals Mt Gordon Operation is a copper mine and processing plant situated 120 kilometres north of Mt Isa. The unique Mt Gordon copper process utilises a whole of ore acid/ferric pressure leach to produce copper cathode from the Esperanza massive sulfide copper orebody. Esperanza ore contains chalcocite, covellite and minor chalcopyrite hosted in a massive pyrite matrix. These ore stocks will be depleted in late 2003. Recently the process circuit has been upgraded to allow the treatment of lower grade Mammoth ores. These include the installation of a ball mill to complement the existing SAG mill, a single stage rougher flotation circuit and a tailings thickener. The leach bleed neutralisation plant was also upgraded at this time. Commissioning of these new circuits occurred in March 2003 and involved all the challenges of ensuring current production levels were successfully maintained while new process steps were incorporated into the whole circuit. This paper explains the background flow sheet of the patented Mt Gordon process and the reasoning behind the enhancements required for an already successful copper leaching circuit. Included are discussion of the influences of the new ores on individual process components such as comminution, leach chemistry and solid/liquid separation. Longer term ore processing options are also discussed.

Jan 1, 2003

By A. C. Rubel

WHAT does management expect of W and from an engineer? First and foremost, it expects that he should become, and therefore should fit himself in every way to be, a part of management so that he may assume as much and as many of the responsibilities of management as his ability and the opportunities of the job permit. Let me make clear at the start that the profession of pure, technical engineering offers but limited opportunities at the top levels because of the inherent organization of engineering work. The line of succession to top jobs may be likened to a cone with a broad base and an extremely sharp point. Consider any oil company, large or small, or any operating function of that company, and you will find few top engineering jobs in the organization. This is true by the nature of the work handled. There will be a few district engineers depending on the spread of operations, a chief petroleum and production engineer, perhaps a few research engineers, possibly some technical executive assistants, and that is usually all. The road to these jobs is a long one and the competition is tough. The larger the organization the greater the opportunity, but always the ratio of engineers to top engineering jobs is only a small one.

Jan 1, 1947