Search Documents

By W. E. Anable

The Bureau of Mines studied the purification of commercially available yttrium by melting it in a 100-kw electron-beam furnace. Button-scale melts were made to determine the ultimate purification that could be attained by melting yttrium at 1,733° to 1,770° C at low pressure (0.05 to 0.1 micron) for 1 to 120 minutes. In addition, numerous melts were made to study the effect of doping yttrium with carbon, 17 selected metallic additions, and 3 compounds. Except for nickel and zirconium, the metallic impurities in yttrium were lowered significantly on extended treatment; silicon was lowered only slightly. The nonmetallic impurities} oxygen, nitrogen, and carbon, were not lowered except on short exposures. In isolated instances, the oxygen content was lowered from 5,860 ppm to about 5,000 ppm. In most instances the carbon con-tent was lowered from 545 to about 220 ppm in 20 minutes and then increased again. It was concluded that yttrium cannot be purified by direct heating or by the doping technique employed.

Jan 1, 1965

By C. K. Baxter, A. Odeshi, M. Mohammadi, E. D. Cyr

"Metal additive manufacturing has been a revolutionary step in designing new complex shapes with faster and cleaner building capacity in comparison to subtractive manufacturing processes. The ability to print lightweight alloys such as aluminum has made metal 3D printing attractive to different industrial sector from aerospace to energy and bioengineering. Of particular interest in this study, are the mechanical and microstructural properties of AlSi10Mg-200°C alloys. In this project, samples were 3D-printed in horizontal direction using an EOS M290 machine by Direct Metal Laser Sintering (DMLS) technique. Uniaxial tensile tests and high strain-rate impact e tests were carried out to investigate the mechanical properties and to study the repeatability of the process. A constitutive model is developed to predict the results of the mechanical tests at varying strain rates to better understand the high strain-rate behaviour of these alloys. Using optical microscopy, features such as scan tracks and melt pools within the AlSi10Mg-200°C samples were observed, and the microstructure was observed to be homogenous. The previously listed tests were compared to the results obtained for similar cast alloy counterpart, i.e. A360.0.INTRODUCTION A relatively new way of manufacturing parts is on the increase as rapid prototyping becomes increasingly popular throughout the world. Additive manufacturing is a process which, given a 3D model, uses metallic material in powder form to build a part layer by layer until completion (Gu, Meiners, Wissenbach, & Poprawe, 2013). This way of rapid prototyping is very attractive in comparison to other possibilities because of its ability to accommodate complex design and geometries. Conventional manufacturing methods have limitations when it comes to complex geometries, but additive manufacturing allows for increased design flexibilities while maintaining a light and stable final product (Murr et al., 2012). It also allows for a reasonable cost, especially for small batch sizes that would otherwise be extremely expensive."

Jan 1, 2018

By R. Kok, N. B. Strydom, P. L. Jooste, W. H. Van Der Walt

Intermittent exposures to heat, and the retention of heat acclimatization by N. B. STRYDOM, M.Sc., Ph.D. (Illinois) (Fellow), R. KOK, M.Sc. (Potch.) (Visitor), P. L. jOOSTE, M.Sc. (Stell.) (Visitor), and W. H. VAN DER WALT, B.Sc. (Potch.) (Visitor) Twenty-one heat acclimatized subjects were assessed for the degree of acclimatization attained with respect to heart rate, rectal temperature, and sweat rate during a standard four-hour heat-stress test. Thereafter, they were put on light duties in cool environm ents for four weeks, except for four hours of exposure to heat every seventh day. Their state of heat acclimatization was again assessed two days after the final week's exposure. Although heart rates and body temperatures showed significant increases over the initial values, no differences were observed in sweat rates and, in general, the subjects were rated as still adequately acclimatized to heat.

Jan 7, 1975

By Glenn Stevens

After 40 years of operation with the original design, Pan Pacific Copper determined it was necessary to rebuild the Saganoseki Flash Smelting Furnace to continue safe operation. The original design employed a rigid steel frame, which, through hearth growth, led to severe distortion of the frame. Contributing to the continued growth of the hearth were thermal cycles that occurred during the government mandated annual shutdowns. Hatch designed a unique sprung bound, pivoting binding frame to maximize crucible size within the existing furnace footprint, while integrating the PPC designed cooling jackets. The bound system maintains tight brick joints, while the new conductive hearth design with integrated bottom cooling produces a protective freeze layer to accommodate higher furnace throughput. Minimization of furnace downtime for the rebuild was achieved through effective construction planning, highly trained contractors, and through an efficient start-up and ramp-up to full production.

By William I. Nissen, Richard Havens

Continuous flotation studies were made at a 50 - lb - per - hr feed rate to confirm the effectiveness of a batch - scale procedure for concentrating phenacite and bertrandite minerals from Mount Wheeler ores that contained , in percent , 0.47 , 0.78 , and 4.7 BeO . The procedure for selective froth flotation of the beryllium minerals from a gangue composed chiefly of calcite , fluorite , and mica comprised closely controlled preconditioning with sodium fluoride and sodium hexametaphosphate in a series of small mechanically agitated tanks and use of a mixture of oleic acid with kerosine , fuel oil , or turpentine as a collector . It was difficult to adapt the laboratory flotation procedure to continuous operation . The principal problem of achieving adequate conditioning to depress calcite and fluorite ultimately was resolved by conditioning in series . Thereafter , three ore samples of different grades treated on a continuous basis yielded concentrates containing from 12 to 25 percent Beo from these relatively complex and difficult ores . Recoveries , on a BeO basis , ranged from 75 to 88 percent . Losses , which primarily were due to incomplete liberation , probably could be lowered in a commercial operation .

Jan 1, 1964

By Raden Haris Handayana, Jihan Farhan Lubis, Milia Putri, Tengku Deli Hamonangan Hasibuan, Sani Salahudin

An environmental issue that must be controlled from coal overburden blasting near the structure is ground vibration. Damaging ground vibration is the effect exerted from residual energy from blasting that does not work to fracture the rocks. Sebuku Tanjung Coal is a coal mining that operates T3 Pit adjacent to the High Voltage Tower. This structure is included in the Class 5 building with a maximum Peak Particle Velocity (PPV) of 40 mm/s. The shortest distance from the blasting location to the structure is 105 m. The initiation system used is electronic detonators combinate with emulsion as an explosives type. In Indonesia, the government regulated vibration limitation on SNI 7571:2010. The blast outcomes targeted are PPV below 40 mm/s, fragmentation size <80 cm for Excavator Komatsu PC-2000, and digging time <12 seconds. In this paper, the blast design was engineered by conducting Signature Hole Analysis for optimizing delay timing configuration and Scale Distance regression analysis to determine optimum charge weight per delay at the blast site. PPV results from 30 blastings achieved 100% below 40 mm/s with the range of about 1.773-30.250 mm/s. The deviation between PPV prediction to PPV actual is less than ±18% which provides the blasting with electronic detonator resulting in good PPV prediction for controlling vibration. The average fragmentation size (D80) is 55.81 cm in the 1st layer and 54.81 cm in the 2nd layer. The average digging time is 10.30 seconds in the 1st layer and 10.12 seconds in the 2nd layer.

Feb 6, 2023

By Z. Yanni, W. Xuan, Z. Jingyu, D. Jun

"In order to conserve the coal resources, many coal mines which have been mined begin to re-mine. Re-mining face is of complicated circumstances and coal spontaneous combustion is unknown, so experiments are designed to study the characteristics of multiple oxidized coal samples. The investigation into the oxidation of coal is conducive to the safe mining of the coal seam groups and thick coal seams. The non-caking coal is collected as coal samples. The raw coal sample with initial oxidation and the sample after second oxidation and third oxidation are obtained after a certain treatment of the coal. The temperature-programmed system, and proximate and ultimate analysis are adopted to compare the releases of gaseous products of spontaneous combustion characteristic parameters of the multiple oxidized coal sample. With the increase of oxidation times, experimental results indicate that the oxygen consumption rate, the release rate of carbon monoxide and the intensity of heat release are significantly decrease. The characteristic temperature dropped and the size of the pores in coal is smaller as well. INTRODUCTION China accounts for 13% of global coal resources [1-2]. In recent years, more and more coal mines begin to re-mine in order to conserve resources. This production mode is to mine coal pillar left by last exploitation or unavailable for mining. In the process of slicing mining for coal seam groups or thick coal seams, the second or multiple oxidation due to the mining-induced effect, may take place in the goaf of the lower seam. So the spontaneous combustion is prone to occur in this area. The study on oxidation of coal is conducive to the safe mining of the coal seam groups and thick coal seams. Scholars [3-7] have discussed the workability of re-mining for coal mines, verify the feasibility of the existing mining technology for re-mining area, and set up the prevention measures of coal spontaneous combustion. But all these measures are only based on on-site observation data, instead of experiment on spontaneous combustion characteristic parameters of re-mining coal samples which have a great importance for early prediction and forecast. The authors aim at investigating the multiple-oxidated coal spontaneous combustion law, and perfecting the coal spontaneous combustion mechanism to provide a basis for the prediction and forecast."

Jan 1, 2015

By M. N. Plis

This report describes the initial results of long-range research on bit life conducted by the Bureau of Mines. Three commercial bit designs -a round-nose radial, 60° conical, and 90° conical with tungsten carbide (WC) inserts -and five experimental bits were tested. Four of the experimental bits were radial designs using polycrystalline diamond compact (PDC) inserts. The fifth was a 90° conical with an oversize WC insert. Bits were worn on a high-silica sandstone typical of coal mine roofs. The bits were mounted on a 34-in-diam drum section that provided a bit speed of 565 ft/min. Cutting forces were measured on a modified vertical slotter using a three-axis force dynamometer and recorded on an FM magnetic tape recorder. Changes in cutting forces, bit weight, and airborne dust due to gradual abrasive wear and catastrophic insert failure are presented. Tabulated and graphed data, photographs of the progression of bit wear, and selected qualitative visual and auditory observations of the bits taken throughout the experiment are found in the appendixes. The results show that bit life ranged from approximately 16,000 ft for the WC round-nose radial bit to over 125,000 ft for a PDC round-nose radial. Performance, in terms of bit life, cutting forces, wear rate, frictional sparking, machine vibration, and noise was in general best with the PDC bits, followed by the rotating WC bits, with the nonrotating WC bits (round-nose radial and locked 60° conical) being the worst. The results show variations in the included tip angles of new conical bits have an insignificant influence on bit performance when the effects are averaged over the life of the bit. In addition, new bits were generally found to entrain more primary respirable dust for a given cutting distance than worn-out bits. It is hypothesized that this is due to the difference in frictional behavior between new and worn bits. The results from these tests are being used in the Bureau&apos;s cutting system model (CSM).

Jan 1, 1988

By O. C. Blade

The oil fields of Arkansas, all situated in the southern part of the State, have played an important part in the development of petroleum production in the northern coastal plain region of the Mid-Continent area. From the first discovery of oil in southwest Ouachita County in 1920 to December 31, 1930, a total of 480,167,5604/ barrels of crude petroleum has been produced from&apos; this region. Development of the Arkansas fields proceeded rapidly after 1920. The El Dorado field was discovered in Union County in 1921. Drilling in Ouachita County resulted in the discovery of the Smackover field in 1922 and subsequently in the development of the whole southern area. To November 31, 1939,459 / producing wells had been drilled in 25 fields, aggregating 53,7356 acres of proved territory in 6 counties. Peak annual production for the State was reached in 1925, when 80,823,7007/ barrels was produced, resulting largely from flush production from the Smakover field, which rose td an average of 444,9507 barrel daily during that year. During 1924, 1925, and 1926 Arkansas ranked fourth among the oil-producing

Jan 1, 1940

By John K. Alley

Despite the extensive use of fluorphlogopite, investigators do not agree as to its exact melting temperature. Data on other fluormicas and on related fluorsilicate systems are largely nonexistent. A knowledge of the melting temperature is necessary for the effective synthesis and use of fluorphlogo¬pite or other fluormicas. The increasing use of two- and three-mica systems to yield polycrystalline ceramics has made more urgent the need for melting temperature information concerning these other fluormicas. This report is part of a program by the Bureau of Mines to synthesize large-size or large-crystal fluorphlogopite and develop a usable reconstituted fluormica sheet. The melting temperature of fluorphlogopite, K2Mg6A12Si6020F4, was found to be 1,383° ±2° C. This temperature was found by studying single crystals of fluorphlogopite, heating behavior of glass of fluorphlogopite composition, and the actual crystallization of fluorphlogopite from a melt that had been heated above 1,430° C. The formation of forsterite or norbergite was directly proportional to the loss of volatiles during the experimentation. Many trials revealed that the only reliable seal was a thick platinum sheet with welded seams. If no volatiles were lost, neither norbergite nor forsterite were formed; fluormica was then the only product. Excellently formed crystals of forsterite with an optical sign different from ordinary forsterite were obtained during the single crystal melting experiments. These crystals resulted from a slow loss of volatiles. A congruent melting of fluorphlogopite is indicated by the data of this report; however, incongruency within a small temperature range is not precluded. A more refined method using phase equilibria-quench methods would be necessary to settle the question absolutely.

Jan 1, 1962

By Sven Petersen, Berit Lehrmann, Bramley J. Murton, Paul A. J. Lusty

"INTRODUCTIONToday’s metal mining focusses on land based ore deposits which only consider one third of the Earth’s surface. Through an increasing global demand of strategic metals used in the electronic and green industry (Zepf et al. 2014), ‘uneconomic’ sites of lower grade in more technical challenging grounds such as greater depth and/or more remote areas are developed by the mining industry often resulting in higher environmental impact. However, considering the steady growth of the Earth population a shortage of certain metals may occur (Krausmann et al. 2009). In 2010, the United Nations allowed commercial exploration for seafloor massive sulphides (SMS) in international waters with currently six contractor licenses being granted.Although the number of discovered vent sites has steadily increased since the first discovery of hydrothermal venting at the Galapagos Rift in 1977 (Corliss et al. 1979) with more than 600 sites being known today, their economic potential is poorly constrained. So far Nautilus Minerals Inc., a Canadian mining company, is the only company having conducted a NI 43-101 resource estimate for the Solwara site, located in the territorial waters of Papua New Guinea. Other studies using bulk geochemical data from 95 sites published in literature do exist (Hannington et al. 2011, Monecke et al. 2016) suggesting a global resource potential for today’s known SMS deposits of 600 million tons with a median grade of 3 wt.-% copper, 9 wt.-% zinc, 2 g/t gold and 100 g/t silver. However, the geochemical data being used originated mainly from easily recoverable, mainly non insitu surface grab-samples and are under current mineral resource classification schemes such as JORC code or NI 43-101 not even accepted for resource estimations. Furthermore surface samples such as high-temperature sulphide chimney and talus material are not representative for the entire deposits with information regards thickness and continuity of individual sulphide layers obtained through drilling being scarce. In addition, it remains unknown what geological processes occur once hydrothermal activity ceases and whether metal tenor becomes enriched, depleted or disappears."

Jan 1, 2017

By Steve Wilson, Bern Klein, Jeff Drozdiak, Stefan Nadolski, Andrew Bamber

"In the adaptation of high pressure grinding rolls (HPGRs) to hard-rock mining applications, circuit development has mainly focused on placing HPGRs in the role of tertiary crusher in the preparation of ball mill feed. In order to take advantage of the potential energy benefits associated with HPGR and stirred mill grinding technologies, work was done to investigate the potential of and resultant energy benefits of placing the HPGR in series with a high speed stirred mill in replacement of the conventional cone crusher / ball mill arrangement. The proposed circuit was designed to operate with two stages of HPGR grinding followed by high speed stirred milling.Using a pilot-scale HPGR unit inline with a 20 liter stirred mill, the design criteria, circuit arrangement and consequent comminution energy requirements for a circuit processing copper sulphide ore from Teck Resources’s Mesaba Copper project were determined. These results were then compared to two other circuits, an HPGR / ball mill circuit and a conventional crusher / ball mill circuit processing the same ore.The testwork indicated at a proof-of-concept level that the HPGR / stirred mill circuit could potentially be appropriate for this duty and further work on the concept is merited. While the results indicate that the HPGR component of the circuit was more energy efficient than conventional cone crushing, the energy efficiency of the stirred mill was found to be lower than that of a comparable ball mill undertaking the same duty. However, increased energy efficiency of the stirred mill portion of the circuit is possible with further optimization and further work on the concept is indicated."

Jan 1, 2010

By Haysler Apolinário Amoroso Lima

O desempenho de uma Aciaria depende da estabilidade dos equipamentos industriais. A conservação do refratário do convertedor garante produtividade, evitando paradas para reparo e campanhas antecipadas. A proteção do revestimento como um todo garante uma maior eficiência do sopro combinado, obtendo ganhos de qualidade e redução de ressopro. O presente trabalho refere-se à busca de soluções de engenharia para aumentar o desempenho do refratário dos convertedores e conservação do sopro combinado pelas ventaneiras. Através do estudo dos mecanismos de desgaste dos refratários, optou-se pelo ajuste dos escorificantes, melhoria das práticas de reparo com escória, mudança do projeto dos tijolos e ajuste da vazão das ventaneiras. Com as melhorias implantadas, houve redução do consumo de massa de projeção e aumento em 100% da vida útil das ventaneiras.

Jul 30, 2018

By Mollie Hunt, William Riley, Russ Downer, Kate Willa Brown Requist, Víctor O. Tenorio, Geoffrey Gill

One of the first activities after returning to the Moon will be finding sources of water and materials for the construction of human settlements and other infrastructure. There is evidence of the existence of deposits in the bottom of craters at the South Polar region and in flat areas around. Based on geological data from the Moon, a block model representing a deposit or icy regolith has been defined in the vicinities of Shackleton Crater, with unique characteristics of shape, thickness, and water contents. A mine plan utilizing surface mine modeling software for ore extraction from an open pit- type of excavation to a delivery point near a water processing facility is proposed, with monthly, quarterly, and yearly schedules. Production results, dashboard charts and progress of the topographic changes are also presented.

Feb 1, 2024

By B Prasad, M P. Roy, P K. Singh, C Drebenstedt

Blasting operations play a pivotal role in the overall economics of opencast mines. The blasting subsystem affects all the other associated subsystems, ie loading, transport, crushing and milling operations. Fragmentation control through effective blast design and its effect on productivity is a challenging job for the practicing blasting engineer due to inadequate knowledge of actual explosive energy released in the borehole, effect of varying initiation practice in blast design and its effect on explosive energy release characteristic. This paper describes the result of a systematic study on the impact of blast design parameters on rock fragmentation at two mines in India. Both the mines use draglines and shovel-dumper combination for removal of overburden. Despite its pivotal role in controlling the overall economics of a mining operation, the expected blasting performance is often judged almost exclusively on the basis of poorly defined parameters such as powder factor and is often qualitative, which results in a very subjective assessment of blasting performance. Such an approach is a very poor substitute for accurate assessment of explosive and blasting performance. Forty-seven blasts were conducted with varying blast designs and charging patterns and their impact on the rock fragmentation are documented. A high-speed camera was deployed to record the detonation sequences of the blasts. The efficiency of the loading machines was also correlated with the mean fragment size obtained from the fragmentation analyses.CITATION:Singh, P K, Roy, M P, Drebenstedt, C and Prasad, B, 2015. Blast design parameters and their impact on rock fragmentation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 755–762 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By T. E. Green, E. F. Spano, W. J. Campbell

A combined ion exchange X- ray spectrographic method was evaluated for the determination of 11 metallic elements in high - purity tungsten : Aluminum , calcium , chromium , cobalt , copper , iron , magnesium , manganese , nickel , titanium , and zinc . Copper , nickel , and manganese in the 5- to 100 - microgram range ( 1 to 20 parts per million based on 5 - gram samples of tungsten ) , calcium in the 10- to 100 - microgram range , and cobalt in the 5- to 20 - microgram range can be determined within an accuracy of ± 10 percent of the amount present . Limits of detection of these elements are 0.05 to 0.14 microgram . The overall method was unsatisfactory for the determination of aluminum , chromium , iron , magnesium , titanium and zinc in tungsten .

Jan 1, 1964

By S. Isaac

The networks of interdependencies between elements in building projects, referred to as the project topology, are often complex and difficult for project teams to comprehend. It is hypothesized that a graphbased model of the project topology can be based on existing data in Building Information Models (BIM), facilitating the application of graph-theoretic algorithms to analyze this topology. The objective of this study is to propose an outline for the synthesis of BIM and graph theory. This synthesis is expected to contribute to the development of new tools for representing, managing and analyzing the design of building projects.

Aug 1, 2013

By A. Paulin, J. Roth, S. Spaic

This experiment was carried out to see whether copper-iron ingots from Late Bronze Age hoards could have been produced by smelting ferruginous copper ores. Since ferruginous copper-ores are chalcopyritic, chalcopyritic concentrate from a present day copper mine was dead roasted in our experiment in lieu of a rich chalcopyritic ore. Charcoal was used as a reducing agent in the reduction of calcine (i.e., a product of dead-roasting), and quartz sand was used as a flux. Two separate metallic solutions, a copper-base and an iron-base alloy, were obtained as a result of two factors: the presence of carbon and the miscibility gap in the Cu-Fe-C system. The metallic melts appeared in a form of bigger or smaller droplets, enclosed by a molten slag which, during the cooling, solidified into metallic beads. The presence of both metals was noticed in the majority of the examined beads. It was therefore concluded that calcine consisted of an intimate mixture of oxides of both metals which were simultaneously reduced during the reduction process. Due to the miscibility gap in the Cu-Fe-C system, separate iron and copper regions were formed in the beads. In both regions, sulphide inclusions were found. The formed molten copper and molten iron solution were found to be saturated solutions. The metallographic analysis revealed the precipitation of iron out of copper and that of copper out of iron during the cooling and solidification of melts. The formed slag contained little iron and no copper oxide.

Jan 1, 2001

By E. W. Engle

For several years the Fansteel Products Co. has been engaged in e production and development of various of the rarer metals. It is at present engaged in the commercial production of tantalum, tungsten, and molybdenum in a very high state of purity. The information contained in this paper is partly a general compilation from various sources and partly information obtained as a result of recent years of work in the laboratory of this company. Tantalum, tungsten, and molybdenum form a group peculiar to themselves among the commercially available metals. Their very high melting points (tantalum 2770&apos; C., tungsten 3350&apos; C., and molybdenum 2550" C.) set them apart so far as the metallurgical processes for their production are concerned. Further, when properly prepared and treated they will stand a somewhat unusual degree of cold work, that is work below the temperature at which marked crystal growth takes place. Such cold-worked metal may show a high tensile strength; tantalum to 130,000 lb. per sq. in., tungsten to 490,000 lb., and molybdenum to 260,000 lb., in the form of fine wire. In physical appearance, these metals are not unlike some steels; they may be better described by saying that polished tantalum somewhat resembles lead; polished tungsten, iron; and polished molybdenum, nickel. The polished surfaces of all three remain untarnished in ordinary air. Air containing corrosion-producing impurities will, in general, show molybdenum the least resistant to corrosion and tantalum the most resistant. Molybdenum has, however, a high degree of resistance to corrosion by hydrochloric acid, a property that should render it of commercial interest. On the other hand, it is markedly attacked by some of the weaker organic acids. The three metals oxidize rapidly when heated at or above a dull red in air. This feature limits their use in many applications where their high melting point and strength make them appear usable. Tungsten and molybdenum, at red heat, are quite inert to hydrogen and nitrogen; while tantalum has a rather remarkable affinity for all the ordinary gases, which results in its becoming embrittled in their presence. This

Jan 1, 1925

By M. I. Brittan

A technique has been developed that analyzes routine mill operating data to determine the key operating parameters responsible for gold losses to tails. These parameters represent the prime operating variables having a dominant effect on gold recovery. The technique quantifies these effects for the specific plant being analyzed, providing a tool to optimize recovery and costs and so enhance the mine?s cash flow. The quantitative relationships generated will be different for each ore and plant: every case is site-specific and has to be treated on its merits. Examples are provided to illustrate the considerable metallurgical and financial benefits which can be realized from optimization. The examples are taken from case studies of mills in four major gold mining districts of the world.

Jan 1, 2010