Search Documents

By Michael J. Friedel

The integrity of mine structures, such as the roofs, ribs, face and supporting pillars, is difficult to assess beyond the exposed surface. To mitigate potential rockfall hazards, the U.S. Bureau of Mines is assessing the usefulness of Rayleigh wave dispersion analysis to detect damage and stress-relieved zones in mine structures. Classical surface wave dispersion modeling is utilized at both laboratory and field scales in damaged and undamaged material to assess the integrity of a mine pillar and roof. To more fully exploit Rayleigh wave propagation characteristics, derivation of a novel dispersion parameter was conducted using a convolutional model. The development of a suitable Rayleigh wave dispersion system based on insight derived from forward modeling is presented. The application of inverse modeling for damage and stress assessment in the mine environment is also discussed.

Jan 1, 2010

By J. H. Zietsman, S. Maharajh, J. Muller

In the chlorination process for TiO2 pigment production, blends of titania feedstocks such as ilmenite, synthetic rutile (SR), natural rutile, upgraded slag, and chloride-grade slag are reacted with coke and chlorine at a temperature of around 1000°C to form TiCl4, which is the main product, and other waste metal chlorides. TiCl4 is the main feed material for the TiO2 pigment-making process. Feeding different titania materials to the chlorinator affects the amounts of coke and chlorine required for the process, the amount of waste generated, waste disposal costs, the amount of TiCl4 produced, and bed build-up rates. These factors influence the value of the feedstock. Generally, a higher TiO2 feedstock is more valued since less waste is generated and less reagents are consumed. To quantify the impact of different feedstocks on the chlorinator, a techno-economic model was developed to describe the chlorination process and estimate process variables at steady state. This paper describes the development of the model and studies in which the model has been used to quantify the effects of using different feedstocks.

Jan 1, 2014

By H. Evans

It is well known that iron-ore pellets are considered one of the best blast-furnace burden materials used today. The demand for pellets is demonstrated by the increase in pellet output from one million tons in 1955 to approximately 37 million tons in 1964. This growth continues as new plants are placed on-stream each year. The consumer generally specified (1) the acceptable content and range of chemical constituents, (2) a minimum strength determined by some standard testing procedure, (3) the size range of pellets, and (4) perhaps a measure of reducibility.

Jan 1, 1966

"Full time inspection of drilled shafts by qualified personnel is a necessary part of construction. Detailed inspection procedures for routine inspection are provided in the Drilled Shaft Inspector’s Manual, published jointly by the DFI and ADSC: the International Association of Drilled Shaft Contractors.The use of NDT methods or other observation methods, such as probes, video camera inspection, remote shaft wall inspection devices or various calipers are not suitable substitutes for routine "topside" construction inspection as described in the Drilled Shaft Inspector’s Manual. However, these NDT and other "remote" or indirect observation methods are valuable alternatives to direct entry of personnel into drilled shaft excavations. They should be considered whenever appropriate to reduce the risks of direct entry of personnel into drilled shaft excavations.As described in the Drilled Shaft Inspector’s Manual, observations made during construction are essential for quality construction of drilled shafts. The shaft depth, diameter, plumbness, bottom conditions, reinforcement, concrete continuity, and bearing conditions are most easily checked during construction. Some of these observation methods include excavation around the shaft for relatively shallow inspection, down-hole inspection for end bearing conditions or rock sockets, and video camera devices for remote inspection. In rare circumstances, a drilled shaft can be extracted for inspection. Before concrete placement, the bottom of the shaft can also be probed by drilling or coring to determine if there are voids or soft zones in the material at the base of the shaft.The Drilled Shaft Inspector’s Manual focuses on traditional "topside" inspection for routine drilled shaft construction."

Jan 1, 2004

By Ernest O. Kartinen

This report is the accumulation of eight years of experience on only one small phase in the business of oil production. It is not intended as a final report but rather as a progress report dealing with the internal corrosion of oil field dehydrating tanks. The corrosion of dehydrating tanks continues to be a problem in the production of crude oil. The deterioration hy corrosion of these tanks falls into three general classifications: (1) Atmospheric corrosion of exterior areas, (2) corrosion of the underside of deck and the rafters and top area of the upper row of staves in that part of the tank which is known as the vapor space, and (3) corrosion of the bottom and shell areas, and the steam coils which are normally immersed in water and thus exposed to the corrosive action of the water. Atmospheric corrosion is primarily a paint problem, and has been omitted in this discussion. The corrosion in the vapor space, in this company's experience, which has been of great concern only in one area. has also been omitted in this discussion. The third, and most troublesome type of corrosion, and the one with which this report deals, is that which occurs in the water-exposed areas of dehydrating tanks, and, to a lesser degree. in some stock tanks. The operating temperature of these waters varies from 80°F to 160°F and the salt counts run from a few thousand to as high as 25.000 parts per million. Corrosion in these tanks occurs in three forms: (1) pits, (2) ringworm type of attack along the vertical and horizontal bolt seams, and (3) as a general attack, spread over a wide area. Steam Coils In dehydrating tanks, our experience has been that the steam coils are the first to show signs of corrosion, and then the shell and bottom areas. This action is not uniform throughout this company's operations. Some installations have coil troubles with very little tank trouble, and some show just the opposite. But in the majority of cases the coils are the more seriously corroded areas. This may be partly due to the fact that we have tried by periodic application to keep a protective coating on the interior areas of the tanks, and some protection has been afforded by these coatings. Through the years several types of hot and cold coatings have been tried with many various methods of cleaning the steel, ranging from use of cleaning solvents to hot and cold Oakite washes, as well as sandblasting. Although experience has shown that a longer life expectancy of a coating is possible after a very thorough steel cleaning job, it has still been necessary to recoat these tanks at least every two or three years. Until a few years ago, vertical spiral steam coil bundles were installed when the tanks were originally erected. When these coils needed replacement, in some cases within 18 months, it was necessary to remove a couple of shell staves to accomplish this task. This required a down time period of several days and was often very inconvenient to the production operations of the leases. This problem was considered on the basis that the coils were expendable, and thus. to eliminate any unnecessary down time when changing coils, the vertical spiral coils were discarded in favor of horizontal flat coils which could be taken in and out of the tanks by way of the cleanout openings, and put together with unions. This made a fairly easily replaceable and repairable coil. But it was still very much of a nuisance when repairs were necessary. Efforts to increase the useful life of the dehydrating tanks led to the adoption of galvanized tanks at an increased initial cost. The zinc coating was depended upon for protection and no other protective coatings were applied. In July, 1944. during the development of a new lease, a 3-ring 1,500 bbl, black iron water tank was converted into a dehydrating tank with steam coils to handle the new production. This tank was coated inside with a cold, brushed-on coating, for protection against corrosion. After approximately 18 months of service, holes developed in the tank and the steam coils. The tank was emptied and cleaned for repairs. The coils were so badly pitted that it was felt advisable to replace them. Coating Becomes Loose Inspection of the tank showed the protective coating to be still in place but loose, and numerous blisters were in evidence. A closer inspection showed that the interior of this tank was so badly pitted under the coating that any further attempt to use the tank was inadvisable. This tank was therefore discarded and a new galvanized tank ordered and set up at considerable expense and inconvenience. In April, 1946, another dehydrating tank installation was made on an adjoining lease. This installation consisted of a 1,500 bbl. 3-ring galvanized tank with two sets of flat steam coils 12 in. and 24 in. up from the bottom. In September, 1947. seventeen months after installation. salt showed up in the boiler feed water. When the dehydrating tank was opened and cleaned, the steam coils were found to be badly pitted — several holes having penetrated through the wall of the pipe. New coils were installed.

Jan 1, 1950

By Charles Goodeve

"BEFORE I begin, I should like to thank The Canadian Institute of Mining and Metallurgy for the honour they have bestowed in inviting me to give this address at the fourth annual C.I.M. Conference of Metallurgists banquet.Secondly, I should like' to convey the greetings of the Iron and Steel Institute of Great Britain in accordance with a request made by its Council at its last meeting. The I.S.I. hopes for the continued growth in strength of this annual Conference and in the collaboration between our respective societies.When I read the program of this Conference, it was brought home to me what a non-ferrons country Canada is. Also, I realized what enormous advances have been, and are being made, and what an ex-citing field non-ferrous metallurgy is for the scientist. This made me wonder, as I have done before, whether the future for steel was proof against these advances.At present, iron and steel stand astride the metallurgical world like a Colossus; I hope that the bronze industry will pardon my stealing their thunder and mixing my metaphors! Will this still be so in the future?The best way to answer this question is to take a look at the fundamentals to see why the iron atom dominates to such an extent that al! other metals are called ""non-ferrons."" Is its present position due to historical and therefore ephemeral reasons, or is there a fundamental difference between the atom of iron and those of other metals?"

Jan 1, 1966

Discussion of the paper of George C. Stone, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 82, October, 1913, pp. 2401 to 2402. D. S. JACOBUS,* New York, N. Y.:-The engineers of the country are waking up to the possibilities of waste-heat boilers. As the cost of fuel increases, and as more attention is given to economies, it is evident that a great deal may lie gained by utilizing heat that has ordinarily been wasted. The art in the manufacture of' waste-heat boilers has. advanced so that it will now pay to install them under certain conditions where it would not have paid to install boilers constructed in accordance with older methods. In using boilers where the gases are at a comparatively low temperature, a great deal depends on the method of baffling the boiler in securing good results. The Babcock & Wilcox Co. has made a careful investigation of the laws of heat transfer and has applied the same to waste-heat boilers, which have been carefully tested under operating conditions, with the result that we now know what to expect with different arrangements of baffles and heating surfaces. The old idea of installing waste-heat boilers was to provide an arrangement where the draft loss would be a minimum, and little or no attention was paid to the effect of different systems of baffling on the steaming capacity of the boiler. In some instances, to secure a minimum draft loss no baffles were placed in the boilers. After making a most careful study of the subject it developed that this practice was bad, and that to obtain the best commercial economy, in place of endeavoring to obtain a minimum draft loss, an arrangement should be used that would lead to the maximum amount of heat transmission with a comparatively high draft loss. In nearly every case the amount of resistance of the gases fussing through the boiler involves the use of an induced-draft ,fan, but the additional capacity developed by the boiler over that which could be secured with the older designs, through arranging the heating surface properly and using proper baffles, much more than pays for the increase in the steam required to drive the fan.

Jan 12, 1913

By William D. Mayercheck

Beginning in 1974, the Bureau of Mines, U.S. Department of the Interior, sponsored R & D efforts related to further development and use of continuous face haulage in underground coal mines (Cowan, 1975). The U.S. Department of Energy continued this effort as of October 1977. This paper represents an update of an article previously published in Mining Engineering magazine (Mayercheck, 1979). Development progress is summarized for a variety of prototype systems or components now being built, surface tested, or tried underground.

Jan 1, 1981

By A. Zeni, S. L. Bessinger, T. A. Palm

San Juan Coal Company (SJCC) operates an underground coal mine near Farmington, New Mexico. Continuous miners and a longwall produce 7-8 million tons per year. The coal seam at SJCC has tested to have a propensity for spontaneous combustion. As such, during feasibility for this project, it was elected to utilize a bleederless ventilation system on the longwall. Three-entry gateroads are developed, and the longwall gob is sealed as mining progresses. SJCC utilizes a nitrogen injection system to continuously inertize the gob. In 2004, the mine was nearing completion of its first longwall district. The next district would contain longer panels (up to 12,500 feet). Due to the liberation of methane, and to a lesser extent hydrogen sulfide, a typical wrap-around ventilation system would not be appropriate. Not only would gas concentrations likely be challenging, but the overall ventilating pressure in the mine would have to be increased beyond limits established to mitigate the potential for spontaneous combustion. Given the above-described operating constraints, SJCC determined a need for a small ventilation shaft in the back (longwall setup area) of the next district that would draw adequate air past the longwall seals to maintain low gas levels and permit the required regulatory inspections to occur. Extensive ventilation modeling and gas desorption testing indicated that the shaft would be required to handle a volume of air ranging from 40,000 cfm to as high as 185,000 cfm. This large range is driven by the position of the longwall face with respect to the shaft and the effectiveness of the SJCC degasification program (SJCC uses vertical gob vent boreholes and horizontal in-seam methods). Ventilation simulations determined an appropriate diameter for the 350-ft-deep shaft to be 5 feet. Having determined shaft size, the next decision related to the method of shaft construction. Conventional shaft sinking was ruled out, due to the small diameter. Raise boring was an attractive option but had two drawbacks: (1) development crews would reach the bottom of the shaft just a few weeks before longwall startup, leaving a compressed timeframe to install the shaft, and (2) raiseboring requires additional underground entries to be developed to stow the project’s cuttings. While raiseboring remained a viable option, the problems associated with it led SJCC to also investigate blind drilling.

Jan 1, 2006

By M. A. D. Azevedo

The effect of pulping reagents on the flotation de-inking of laser printed wastepaper was investigated with regard to the removal efficiency of toner and mineral filler particles for different pH values. These results show that caustic pulping causes the toner to be released from the fibers at larger particles sizes. On the other hand, acid pulping not only causes the toner to be released at smaller particles sizes but also increases the concurrent flotation removal of mineral filler particles. It was experimentally observed that the froth generation and stability during flotation were improved for acidic pH values.

Jan 1, 1997

By L. M. Oshinowo

The incorporation of advanced analysis tools, such as CFD, into the process plant design process has become possible through advances in commercially available computational fluid dynamics software and faster computers. Multiphase modeling is now typically employed in the design phase of process plant design at Hatch. The multiphase models include Lagrange-Euler and Euler-Euler treatment of the multiple phases. Additionally, mixture models with interface-sharpening algorithms are applied to the prediction of free-surface flows in complex geometry. CFD is applied to applications where traditional design rules are not applicable. The additional rigor of CFD modeling in 2D and 3D allows process engineers to come closer to realizing true virtual plant design. The objective of this paper is to outline the benefits and pitfalls in the application of multiphase modeling for rigorous design. Several application examples in the hydrometallurgical field will be presented.

Jan 1, 2005

By Reed M. Izatt

SuperLig® materials are capable of individually separating Rh, Pd, and/or Pt in highly purified form (99.95 to 99.99%) from a variety of chloride-based feed streams in a single stage operation. The hydrophillicity and associated kinetics of the supported materials allow for operation at relatively high flow rates of both loading and elution in a packed bed format. Pilot and commercial systems have been operated with Rh, Pd, and/or Pt present in the feed from single digit ppm (mg/l) to tens of g/l. A dual SuperLig® system for one pass Au(CN)2- separation followed by Cu and CN- recovery for CN- recycle has also been tested up to a pilot level,

Jan 1, 1999

By Donald J. Barnes

The Glacier View RARE Ii further planning area contains no identified mineral deposits, other than stone, which cannot compete favorably with similar deposits closer to major markets. Pierce County mining claim records show six coal claims were located in the study area between 190b and 1907; however, no coal was found at the described locations. Two coal prospects, the H.O. Lamming and Floyd Rice, are within 0.5 mi (0.8 km) of the area's west boundary (fig. 1). At these prospects, impure bituminous coal beds strike approximately north and dip east toward the study area. Analyses of samples 1/ indicated an average heating value of 2,767 BTU 2/ per pound (6,436 joules per kg). Because of the low heat value, this coal is subeconomic. Intense folding and faulting which disrupted the beds would limit the use of conventional coal mining equipment, making future economic development even less likely. Trinity Resources of Houston, Texas has leased approximately 1,404 acres (568 ha) inside the study area and an additional 1,020 acres (413 ha) adjacent to the study area for oil and gas exploration. However, no oil or gas wells are known to have been drilled in or around the study area.

Jan 1, 1983

By Patrick F. R. Murphy

The mechanization of platinum group metal (PGM) underground reef mining in South Africa has posed a challenge to mining engineers for several decades. This is primarily due to the shallow dip angles and narrow thickness (<1.1m) of the tabular orebodies mined, and the issues faced in developing reliable drilling, bolting and loading machines suitable for such hard-rock mining applications. Presently, mining is typically conducted using hand drills and scraper shovels. These methods, however, are intensive in terms of manual labor, and limited in terms of productivity, and improved methods are desired. This paper will review the technical features of a 4 tonne, low-profile, LHD for narrow-reef PGM mining, developed by EJC Loaders Division.

May 1, 2003

By A. Brian Hawkins

"When pyrite oxidizes in dark grey/black, calcareous, mudrocks or in argillaceous limestones, ferrous sulfate is formed and sulfuric acid is released. The sulfuric acid combines with the calcite present in the rock and calcium sulfate (gypsum) develops. When this occurs on the outer edges of aggregate particles, the gypsum forms in the matrix hence there may be little expansion of the general material. However, when the chemical reactions occur within the rock fragments, particularly on microscopic, clayrich, laminae, the developing crystals exert a significant pressure on the host material. If the rock is medium strong to strong, the force of crystallization splits the rock along the weaker planes, facilitating the ingress of the oxidizing agents and the continuation of the chemical reactions. In addition to causing dilation/heave, some of the engineering properties of the material are changed, including the strength, Los Angeles value, water absorption etc. As a consequence material, which at the time of quarrying would be acceptable for use beneath floors or hardstandings, would no longer be considered suitable.INTRODUCTIONMudrocks accreting in aerobic environments are frequently disturbed by organisms and as a consequence there is often little sign of bedding. In contrast, sediments which have formed in anoxic environments commonly have distinct bedding planes which, because of the grain size of the accreting material, are often smooth and planar. These rocks are frequently referred to as shales, which O’Brien and Slatt (1990) define as “characterised by a finely laminated structure, which imparts a fissility approximately parallel to the bedding.” This should not be confused with rhythmic bedding where the variation in grain size results in lithological laminations or colour changes.Early geologists, in the stratigraphic naming of rocks, often used the term shale for material which is now more likely to be described as mudstone or mudrock (Hawkins and Pinches, 1992). In many contexts, the width of the bedding is an important factor, not only in determining the rock name but also in indicating the potential engineering characteristics. Until recently a shale was considered to have bedding separations of less than 20mm, i.e. the bedding was described as laminated. However, in an engineering context, EN 14689: 2003, Annex A, defines shale by specifying a bedding thickness of < 6mm; such a material would be described as thinly laminated in BS 5930:1999. Ideally the term shale should be abandoned and be replaced by fissile mudstone or fissile mudrock."

Jan 1, 2015

By William O. Vanderburg

The fluorescence of many minerals, when excited by different wave lengths, of ultraviolet radiation, has long been recognized as a spectacular laboratory phenomenon. Since the original display in the British Museum, the phenomenon has been used frequently for educational purposes and public demonstrations. Its practical application for the rapid detection of certain minerals in ores and mill products at the zinc mine at Franklin, N. J., has been described.3 Due to technical improvements in ultraviolet-radiation apparatus, fluorescence has found a new field of application in the tungsten-minim; industry. Although fluorescence of scheelite (calcium tungstate) has been known for a number of years, the practical application of the phenomenon is the outgrowth of a program of cooperative research conducted by Ott F. Heizer, manager of the Nevada-Massachusetts Co., Inc. , Mill City, Nev., and Dr. Paul F. Kerr of Columbia University. Special portable lights for fluorescing scheelite have been developed and utilized in underground geological work. Thanks are due Ott F. Heizer for permission to publish data included in this paper.

Jan 1, 1935

By Peter Zhang, I. BERK TULU, Morgan M. Sears, Mark Van Dyke, Heather Dougherty, Ted Klemetti, Gabriel S. Esterhuizen

Ground falls in longwall gateroad entries remain a concern in modern longwall operations. The gateroads are subject to changing horizontal and vertical ground stress induced by longwall extraction. These stress changes can result in failure of the strata around an entry leading to large deformations of the entry roof, floor, and ribs. The gateroad support systems are required to control the failed strata while maintaining safe access to the longwall face and unimpeded ventilation. This paper presents research that was conducted to better understand the stability issues in gateroad excavations and to develop procedures for evaluating support and layout alternatives for longwall gateroads. Using the results of a field-monitoring program and numerical model analysis of case histories, a conceptual model of gateroad support needs was developed. The conceptual model formed the basis for developing a set of equations that can be used to estimate likely roof sag and support loading for given roof geology and longwall-induced loading conditions. The developed equations were used to compare predicted gateroad stability to field study results, showing satisfactory agreement. The calculation procedures are used to demonstrate their application in assessing support alternatives at a case study mine. It is concluded that the developed analysis procedures provide realistic assessments of likely ground stability and can be used to evaluate alternative gateroad support systems at operating longwall mines.

May 13, 2021

By David K. Hylbert

This study investigated roof falls in room-and-pillar drift coal mines in eastern Kentucky and utilized geologic methods for predicting roof conditions in advance of mining. In the Highsplint mine, the roof was classified in four categories or conditions: Condition A and B (Laminated Shale), Condition C (Rolling Sandstone with Shale in Pockets) and Condition D (Zone of Major Sandstone Roll(s)). Structure contour and isopach maps of the Darby coal bed and associated immediate roof rocks were used to project axial trends of the sandstone roof. Trend mapping in the mine and on outcrop provided more detailed control for roof projections.

Jan 1, 1978

By Botao Lin, Yan Jin, Hongjuan You, Jingjun Pan, Huiwen Pang, Mian Chen, Sen Chen

"Steam Assisted Gravity Drainage (SAGD) has become the mainstream technology for ultra-heavy oil recovery in Xinjiang oilfield, the success of which depends heavily on shortening of preheating period as well as forming homogeneous and highly permeable zone in land-facies oilsands layer. Towards this aim a special hydraulic fracturing process is required, which is accomplished through controlled water injection to a pair of horizontal wells in order to create homogenously distributed microcracks in the zone between the two wells. The associated mechanical response, however, is unclear for land-facies Karamay oilsands that is loose in texture. In this regard, this research utilizes a triaxial test system on cylindrical specimens extracted from field-collected oilsands cores. Isotropically consolidated drained triaxial compression tests are conducted on both saturated and unsaturated specimens so as to investigate the mechanical response of oilsands at different spots relative to the wellbore. Moreover, acoustic emission and fast pulse-decay permeability are performed to monitor fracture development and permeability evolution. Based on these experimental studies, the mechanism of dilation in oilsands is comprehensively analyzed. The findings reveal distinctive behavior between the saturated and unsaturated specimens as respect to dilation, porosity/volumetric evolution and change of permeability. It is also found that shear bands can be created upon shearing on triaxial specimens, rendering porosity or volumetric strain the factor that is more proper for evaluation of stimulation efficiency in the field.INTRODUCTIONXinjiang oilfield is widely known for its abundant deposit of heavy and ultra-heavy oil that has been estimated to be several hundred million tons. The ultra-heavy oil deposit located in Fengcheng region of Karamay at the northwestern part of the Junggar Basin, Xinjiang, China, has over 360 million tons of resource (Yuan et al. 2013). The resource is deposited in depths from 180 to 450 m and has viscosity over 100, 000 mPa•s at a temperature of 50ºC, bringing technical challenges to recovery activities."

Jan 1, 2015

By D. R. Lanners

Samples of the same coal measure overburden spoil were obtained from three different mine sites. Site A used a 27-m3 tub-mounted dragline, Site S used a front-end loader and truck combination, and Site C used a 6-m3 crawler-mounted dragline. The spoils were analyzed in the laboratory for the strength parameters using drained triaxial tests conducted on 150-mm diameter specimens. Regression analysis was utilized to determine the appropriate failure criterion for the strength data from each site. Spoil obtained from Site S yielded higher shear strengths than Sites A and C.

Jan 1, 1993