Search Documents

By Chris Rule

This paper tells the story of the rapid commercial application of stirred milling technology at Anglo American Platinum?s many Concentrators. The first stirred mill ? a 10 000 litre IsaMillTM; the largest at the time, was commissioned in late 2003. The project development work was presented at SAG 2001. This operation was ?proof of concept? and vindicated the decision to scale up the technology; allowing a rapid and extensive roll-out of mainstream regrind mills as well as several further flotation concentrate regrind mills, over the next six years. Currently 23 stirred mills are in operation with 64 MW of installed drive capacity ? this paper describes the projects? roll-out and the significant results achieved to date. Many operational problems have been solved along the way, some of these will be described. The introduction of the technology has seen a step change in metallurgical results and progressively decreasing operating costs.

Jan 1, 2012

The saying that a "prophet" is without honor in his own country does not always hold true, as is shown by the following from one of the local papers, which appeared under the above heading: "Edwin Ludlow, for more than seven-years vice-president of the Le-high Coal.& Navigation Co., with headquarters in Lansford, has resigned, to take effect July 1, when he will take up his residence in New York and engage as a consulting engineer. Mr. Ludlow, during the incumbency of his present position, has demonstrated his efficiency as an engineer and general manager in many directions, notable among which are the almost perfect methods in practice in the inside workings of the several operations under his charge and the erection of the most complete, most practical and most commodious breakers for the preparation of the mine product for market. In addition, his relations with organized labor have been cordial and his dealings with its representatives have been invariably based upon the principle of fair play."

Jan 7, 1919

By Donald J. Hallbom

Limonitic nickel laterites slurries exhibit complex rheological properties including time dependency that varies from thixotropy to rheopexy. Chronic problems may occur if plant designers and operators fail to take time dependency into account. Stress decay tests indicate that laterite slurry takes roughly two minutes to approach steady state after a step change in the shear rate. As a result, most rheometer measurements are taken at a non-equilibrium state, making evaluation difficult. Two minutes is also long relative to the time that a unit of slurry in a processing plant is at any given shear state, so the slurry may never reach equilibrium. This paper presents a method to describe the rheology of laterite slurry using a Flow Array, which describes the rheology using an array of instantaneous flow curves crossed by an equilibrium flow curve. A rate equation for structural change in non-equilibrium conditions allows time dependence to be efficiently modeled. This flow array allows the flow behavior of time- dependent slurry to be predicted in non-equilibrium conditions using a simple time-step methodology. Keywords: Rheology. nickel laterite, hydraulic transport, pressure acid leach, flow array

Jan 1, 2004

By Xin Zhou, Huilin Jia, Xiaofei Liu, Jinxin Wang, Zifeng Meng, Zinan Du, Hui Xie, Guihang Jiang

The change of gas emission or concentration level at the working face is one of the main precursor characteristics of coal and gas outburst. At present, coal and gas outburst monitoring and early warning are mainly based on whether it exceeds the limit and its change law. However, the gas concentration level is affected by factors such as coal seam gas content, permeability, and mining process, and the change law is complex to recognize manually. In this paper, the response characteristics of gas concentration level in the mining process are analyzed and revealed, and a bidirectional long short-term memory model is established. The change characteristics of the gas concentration level in the mining and non-mining processes are studied and recognized. The results show that the change law of gas concentration in the mining process has apparent periodicity and trapezoidal volatility. The proposed intelligent recognition method based on the bidirectional long short-term memory neural network can automatically recognize the underground mining and non-mining processes, and the recognition accuracy achieves 97.7% . The research can significantly help improve the level of coal mine safety management and the accuracy of early warning of coal and gas outburst.

Apr 29, 2023

By G. W. Jones

As a part of it investigations pertaining to the promotion of safety, the Bureau of Mines is investigating various means, useful for the elimination or mitigation of the explosion hazards of combustible gases encountered in mining and industry. Information has been obtained and a procedure developed whereby the explocibility of many complex, gaseous, combustible atmospheres may be calculated in a simple manner without the necessity of performing laborious laboratory experiments. In a previous publication4/ data were given and a method described whereby the limits of inflammability of gaseous mixtures, including methane, hydrogen, carbon monoxide, nitrogen, carbon dioxide, and oxygen, could be determined by calculation. The information published in that report enables one to calculate the limits of inflammability of such gases as are liberated by mine fires, gases from explosives, automobile exhaust ran, uses present after mine explosions, blast-furnace gas, and other gases containing part of or all of the above-listed constituents.

Jan 1, 1938

By Jane Li, Kevin Tom

"Research has shown that broken rock on conveyor transport systems can contribute upwards of 50% towards the overall heat load in underground mines. However, few studies have made significant efforts to predict the temperature distribution of the ore and air simultaneously, which can help implement heat management strategies. The present investigation explores a transient, analytical heat transfer model to track ore-pile temperature distributions, along conveyor systems in an example underground mine. Production rate, ambient conditions, ore pile thickness and belt velocity are adjusted to evaluate the effect on dry and wet bulb temperatures.INTRODUCTIONWith an ever increasing demand on Earth’s resources due to a multitude of factors like population growth and step changes in technology, pressure on the mining industry to bring out more ore with improved margins is a persistent challenge. Typically, high-volume producing mining methods (i.e., exceeding 5000 tons per day (tpd)) such as sublevel and block caving, room and pillar, and longwall shall utilize belt conveyors instead of trucks as the primary haulage method to surface to save on operational costs (de la Vergne, 2014). However, studies have shown that when such material transport systems are installed at mine depths with virgin rock temperatures (VRT) above 40oC, the heat dissipated by the conveyed ore can account for over 50% of the underground heat-load (Pareja, 2000; Bluhm, Jones, Moreby, & von Glehn, 2012; van den Berg, Moreby, & Kok, 2015).Unlike other types of heat sources encountered in underground mines, such as diesel machines, strata, electrical devices, and autocompression, heat transfer by conveyed broken rock is much more difficult to estimate. The seminal work of McPherson (1993) states that broken rock heat transfer is a function of its surface area, and the air’s psychrometric condition. It is additionally a function of the VRT, its specific heat, production rate, heat transfer coefficient and the residence time (Bossard, 1997; Ross, Tuck, Stokes, & Lowndes, 1997). Consequently, few studies have attempted to analytically quantify the significance of ore heat flow."

Jan 1, 2019

By C. H. Hopper

THE gold orebodies of the Matachewan Consolidated mine are of particular interest geologically because of their odd shapes, their apparent lack of connection one with another, and the fact that they occur in a number of different formations. All of the orebodies exhibit a similar fracture pattern and the areas of fracturing appear related to the local folding. However, the lack of either horizontal or vertical continuity suggests additional controls not yet discovered. The question of origin, so ably discussed by H. C. Cooke in 1919, will be reviewed in the light of the additional evidence uncovered since his examination of surface trenches twenty-four years ago. The Matachewan Consolidated mine, with its neighbour, the Young-Davidson mine, is in Powell township, 25 miles by road northwest from Elk Lake, 30 miles west of Kirkland Lake, and 45 miles southeast of Porcupine. It may be considered as being on the westerly extension of the Kirk-land Lake sedimentary belt, where the rock column is markedly similar. There is no similarity in structure, however, for great ore-bearing shears and faults simply do not occur at Matachewan. Rather may it be said that the region, under stress, failed in isolated brecciated patches, some of which make up today's orebodies. The mine currently treats 1,000 tons a day of porphyry ore averaging 0.10 oz. gold per ton. It started operations in 1934 on greenstone ore, and the mill then treated 150 tons a day of ore averaging 0.23 oz. gold per ton. Total production to the end of 1941 has been 929,484 .tons averaging 0.160 oz. gold per ton.

Jan 1, 1942

The Tom's Gully gold mine is located 90km ESE from Darwin, in the Northern Territory of Australia. The orebody is the auriferous portion of a large sulphide rich quartz reef, hosted in the Wildman Siltstone Formation of the Early Proterozoic Pine Creek Inlier, at the NH extremity of the Mount Bundey granite-syenite intrusion. It was discovered by Carpentaria Exploration Company Pty Ltd on November 17th, 1986, using stream sediment geochemistry.The reef is 800m long at surface, strikes E-H and dips approximately 300 to the south, becoming progressively less steep. Only the eastern half of the reef is auriferous, with gold grades averaging 9 g/t plus anomalous silver, base metals and arsenic.The enclosing siltstone is a dark grey banded carbonaceous and pyritic metapelite, showing areenschist regional metamorphism and thermal effects from the adjacent pluton. Local folding plunging gently SW is cut by a south dipping fault, probably a thrust, in which the reef was later formed at about the time of the granitic intrusion. The main sulphides in the reef are pyrite and arsenopyrite, with gold occurring as microscopic particles in...

Jan 1, 1990

By J White

The Eyre Peninsula (EP) has been known for its iron ore for more than a century. Edward John Eyre noted the ironstone outcrop at what is now Iron Knob in the 19th century. Sir Douglas Mawson visited and reported on the geology of the lower EP in 1906, noting the widespread presence of iron stone and the likelihood of copper being associated with the iron stone. Despite this knowledge there has been only one successful iron ore mining region developed on the EP and that is Iron Knob and the Middleback Ranges which have been mined continuously since 1899. The Middleback Ranges can justly lay claim to be birth place of the Australian iron ore and steel industries.The discovery of large scale haematite resources in Western Australia meant that there was no need to seek out iron ore that needed benefi ciation. The low price of iron ore precluded further development of the EP and many other areas in Australia and overseas. This situation changed rapidly in the mid-2000s with the emergence of China as the world’s industrial power house and the soaring demand and price for many resources including iron ore. This triggered a flurry of activity across Australia and led to the rapid exploration and drives to develop the EP iron ore. A brief examination of the magnetic maps of the EP shows the wide spread presence of magnetite and associated smaller haematite deposits. A closer look reveals the magnetite deposits to vary in formation style and host rock lithology as well as being significantly altered by regional metamorphism. *This is an abstract only. No paper was provided for this abstract.*

Jul 11, 2011

By L Dzinza, K C. Corin, M Tadie

The recycling of process water comes with increased electrolyte concentrations that affect water quality, which may in turn affect the flotation performance of valuable minerals (Hirajima et al, 2016). Electrolytes such as Ca2+, SO4 2- , Mg2+ and S2O3 2- have been surmised to have an impact on the action of flotation reagents such as collectors (Ikumapayi et al, 2012). Xanthate collectors are known to play a significant role in imparting hydrophobicity on mineral surfaces to enhance their flotation. The interaction between minerals and xanthates is well known to be electrochemical in nature. Such redox processes may be elucidated by electrochemical techniques. Since the mechanisms involving the interactions between electrolytes in process water with sulfide minerals and the subsequent adsorption kinetics of collectors are not well understood, this study therefore aims to provide fundamental knowledge to unpack the mechanisms involved when electrolytes interact with Platinum Group Minerals (PGMs) and how these interactions may affect xanthate adsorption. The interaction of sodium iso-butyl xanthate (SIBX) in the presence of electrolytes at increasing ionic strength was investigated by rest potential measurements, to explain the impact of electrolytes on the adsorption of SIBX on PGMs in the flotation process. Rest potential measurements for PdTe2 and PdS were conducted in an air saturated 0.05 M di-sodium tetraborate decahydrate solution, in the absence and presence of SIBX and electrolytes. It was found that the existence of sulfide and telluride on palladium affects the mechanisms in which electrolytes interact with Pd mineral surfaces. An increase in the ionic strength of Na2S2O3, CaCl2 and MgCl2, increased the interaction between the salts and PdS, thus decreasing the extent to which SIBX interacted with PdS. An increase in ionic strength for Na2S2O3 increased the interaction between Na2S2O3 and PdTe2 and therefore decreased the extent to which SIBX interacted with PdTe2. Other salts investigated in this study increased the rate of oxidation of PdTe2 with an increase in ionic strength thereby enhancing the interaction of SIBX and PdTe2. This study has shown that mineral type, electrolyte type and concentration all have an impact on the mechanisms that result in the adsorption of SIBX on PGMs.

Aug 24, 2022

By V.K. Zworykin

Throughout its development the science of electronics, like so many other branches of science and industry, has been indebted to the metallurgist. Metallurgy has provided the electronic engineer with conductors to furnish passage for electrons outside of his evacuated tubes: it has developed tungsten and tantalum wires for emitting electrons and various refractory metals and alloys suitable for electrodes, which receive them and guide them within the tube; finally it has supplied ferromagnetic materials both for shielding electronic apparatus from magnetic fields and for forming highly concentrated fields for deflecting electron . Today I hope to show you that electronics has not been altogether ungrateful for this assistance. More specifically, I wish to indicate the role that the electron microscope, a relatively recent product of electronic engineering, is playing even now in the study of metals. Every metallographer is aware that his standard metallographic microscope will not reveal structural detail involving separations smaller than a certain fraction —at the very best a tenth—of a micron. This limitation, he knows, is a consequence of the fact that the wave length of the light employed for forming the image has this order of magnitude. It is, thus, a property of all light microscopes. TO overcome it, a different imaging medium must be employed, The existence of such a medium became evident when it was demonstrated1 that electrons were affected by magnetic and electric fields with axial symmetry just as light is affected by glass lenses; these fields, or "electron lenses," curve the paths of electrons reaching them from an object located on the axis of symmetry in such a manner that, at some distance from the lens, a true image of the object is formed. Furthermore, although a wave length may . be ascribed to electron beams just as to light, this wave length is much shorter; for electrons accelerated through a difference of potential of 50 kilovolts, the wave length is only about one hundred-thousandth of that of visible light. Actually, the elcctron microscopes of today resolve detail one hundred times as fine as light microscopes; if the maximum useful magnification of the latter is taken to be a thousand, that of electron microscopes is one hundred thousand. The Electron Microscope Since electrons are readily scattered and absorbed by matter, specimens to be observed in the electron microscope must be prepared to be less than one micron in thickness; furthermore, the interior of the microscope must be carefully evacuated to prevent collisions between the clectrons and the molecules of the air. Finally, as already mentioned, the lenses are formed by axially symmetric magnetic or electric fields, and not by any material medium such as glass. Apart from these basic differences, the electron microscope closely

Jan 1, 1943

By V. K. Zworykin

Throughout its development the science of electronics, like so many other branches of science and industry, has been indebted to the metallurgist. Metallurgy has provided the electronic engineer with conductors to furnish passage for electrons outside of his evacuated tubes: it has developed tungsten and tantalum wires for emitting electrons and various refractory metals and alloys suitable for electrodes, which receive them and guide them within the tube; finally it has supplied ferromagnetic materials both for shielding electronic apparatus from magnetic fields and for forming highly concentrated fields for deflecting electron . Today I hope to show you that electronics has not been altogether ungrateful for this assistance. More specifically, I wish to indicate the role that the electron microscope, a relatively recent product of electronic engineering, is playing even now in the study of metals. Every metallographer is aware that his standard metallographic microscope will not reveal structural detail involving separations smaller than a certain fraction —at the very best a tenth—of a micron. This limitation, he knows, is a consequence of the fact that the wave length of the light employed for forming the image has this order of magnitude. It is, thus, a property of all light microscopes. TO overcome it, a different imaging medium must be employed, The existence of such a medium became evident when it was demonstrated1 that electrons were affected by magnetic and electric fields with axial symmetry just as light is affected by glass lenses; these fields, or "electron lenses," curve the paths of electrons reaching them from an object located on the axis of symmetry in such a manner that, at some distance from the lens, a true image of the object is formed. Furthermore, although a wave length may . be ascribed to electron beams just as to light, this wave length is much shorter; for electrons accelerated through a difference of potential of 50 kilovolts, the wave length is only about one hundred-thousandth of that of visible light. Actually, the elcctron microscopes of today resolve detail one hundred times as fine as light microscopes; if the maximum useful magnification of the latter is taken to be a thousand, that of electron microscopes is one hundred thousand. The Electron Microscope Since electrons are readily scattered and absorbed by matter, specimens to be observed in the electron microscope must be prepared to be less than one micron in thickness; furthermore, the interior of the microscope must be carefully evacuated to prevent collisions between the clectrons and the molecules of the air. Finally, as already mentioned, the lenses are formed by axially symmetric magnetic or electric fields, and not by any material medium such as glass. Apart from these basic differences, the electron microscope closely

Jan 1, 1943

By Qing-hua Tian, Li-then Cheng, Xue-yi Guo

In order to recycle valuable metals from silver separated residue, a novel method using alkaline smelting at low temperature was proposed. The main factors affecting the main metal recovery such as the smelting temperature, smelting time, liquid-to-solid ratio and alkali addition were investigated comprehensively. The behavior of the main metal elements, such as Pb, Sn, Sb and Bi in silver separated residue was also discussed. The results indicated that amphoteric metals such as Pb and Sn can be smelted into the melt, while other metal elements, such as Sb and Bi were left in the residue.

Jan 1, 2011

By D. F. Lillie

The milling plant of Bicroft Uranium Mines Limited has been in operation for a period of 2 years. During this time many changes, both physical and chemical, have been made in an effort to improve plant efficiency. Investigational work has been facilitated greatly by the fact that the Bicroft mill consists to a large extent of two parallel circuits; however, the number of inter-related variables is great, and it is difficult to measure, let alone control, all of them simultaneously. The Bicroft mill staff feel that much progress has been made, but there is much yet to be done and many questions still to be answered. The property of Bicroft Uranium Mines is located in Cardiff Township in the Highlands of Haliburton County, southeastern Ontario, some 140 miles northeast of the city of Toronto and 70 miles due north of Lake Ontario. The ore-bearing dikes are classed as mafic, non-segregated, syenite and granite pegmatites. Microline, microline perthite, quartz, uraninite, uranotharite, fluorite, titanite, cyrolite, calcite, pyrite, pyrrhotite and molybdenite as important accessories. The mill was designed for a nominal capacity of 1,000 tpd with all sections except grinding, leaching and clarification capable of 1,500 tons. Feed was entered to one mill unit on October 29, 1956 and to the second parallel line on November 13. The total feed rate was at 1,000 tpd on November 15. The first precipitate was produced on November 12. By August 1958 the average entry had been increased to 1,410 tpd without the installation of any additional major equipment. The overall recovery has been greater than 93,0 pet do several months, but a recovery of 92.5 pct appears to be most economical. Operating time for 8 months in 1958 has been 97.1 pet although all grinding mills were relined during this period.

Jan 1, 1959

By AIME AIME

THAT neither the Reconstruction Finance Corp. nor its subsidiary, the Metals Reserve Corp., are in competition with private enterprise was stressed by Charles B. Henderson in an informal talk before the N. Y. Section, A.I.M.E., on Sept. 23. Among other things, the speaker stated that the R.F.C., since its establishment, had authorized loans of $12,000,000, of which over $8,775,000 has actually been distributed. Of this amount, over $6,600,000 has been repaid. None of this money was appropriated by Congress, the sole assistance from that body being the initial authorization of $500,000,000 capital stock.

Jan 1, 1941

By JOHN R. SUMAN

IT SEEMS particularly appropriate that the Institute's Regional Meeting should be held in Minnesota this year. Whether we like it or not, we cannot help looking at things now in the light of the World War and the all-out effort we, as a nation, are making to defend our resources, our institutions, and our way of life. The ability to do this lies in large measure in the ability to forge weapons of defense-the machines of war. The basic ingredients of any defense system, or war machine, are the raw materials of industry-iron ore, providing steel for guns, shells, tanks, and warships; coal for stoking the nation's furnaces; oil to furnish power for war planes, ships, trucks, and mechanized weapons; and all the other materials that play a vital role in the operation of modern armies and navies. The tremendous requirements of full-scale defense programs are indicated by the large number of commodities that are now under priorities because the supply is not sufficient to meet both defense needs and all normal civilian consumption. But out of all these items two are of paramount importance-steel and petroleum. In this age no nation can hope to main¬tain a position as a first-class power in the world without a highly developed industry, particularly the heavy industries based on steel, and without access to the necessary resources for those industries. In 1918, 70 per cent of the iron and steel production of the United States was required for defense purposes. In 1940, 15 per cent of our iron and steel production was consumed for defense purposes, and with the acceleration of the defense program, it appears that the proportion of steel output required for defense purposes will reach 40

Jan 1, 1941

By A M. Barrett, P J. Chapman

As filtering technology improves and there is an increased focus on environmental impacts, the concept of managing fine coal rejects by filtering, mixing with coarse rejects and dry stacking them is being considered more seriously. In Queensland, there appears to be a desire from regulators to move away from wet rejects facilities towards dry-stacked facilities, resulting in a change in the risk profile for the facility.A coalminer has a site with many constraints, including limited area that is not planned to be undermined and nearby rivers that are prone to flooding. The design of a dry-stacked facility that meets the operational requirements and environmental compliance criteria is challenging in subtropical climatic settings, where there is a need to consider wet seasons with high-volume, sustained rainfall events. The impact of the rainfall is multifaceted, requiring careful surface water management to separate clean and contact water, adequate foundation preparation to limit seepage to groundwater, management of stack stability given a potentially high phreatic surface and the avoidance of potential flood zones. These design constraints were compounded by a limited area available for rejects storage that would not be undermined.This paper presents a summary of the conceptual design of a dry rejects facility, including consideration of regulatory and client requirements, provision for expansion while also considering progressive rehabilitation, diversion of clean water as much as practicable during operations and siting constraints. A step-by-step concept is presented that addresses each constraint during the life of the facility.CITATION:Barrett, A M and Chapman, P J, 2015. Conceptual design of a dry-stacked coal rejects facility in a subtropical climate, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By T. F. Dumm, O. Trass, V. R. Koka, L. G. Austin

"The size distributions of carefully screened 2 size fractions of ground materials were determined using a Microtrac laser dif-fractometer. The size distributions were fitted to the empirical function P(x) = 1/[1 + (x50/x)1] where P(x) is cumulative mass fraction less than Microtrac size, x. The standard deviation of A for a 50 second test time was approximately 0.5, so that seventeen test times give a mean with an estimated error within t 0.25 (95% confidence level). Values of were 5.44, 4.82, 4.40 for a coal ground under different conditions, indicating statistically different shape distributions; the average value for mica was 2.91 owing to the high aspect ratio of the particles. The ratio of x50 to the geometric mean sieve size was 1.2 for the coal and 0.70 for mica.1 IntroductionKoka and Trass have presented evidence [1,2] that materials ground in the Szego mill [3] give different shapes depending on the milling conditions. The variations in shape were deduced qualitatively by viewing SEM photomicrographs of selected 1/2 screen fractions. This paper quantifies their observed differences in shape by using measurements of the size distributions of screen fractions examined in a laser diffractometer [4] (Microtrac, Model 7991). The basic concept is that particles of 'a given ""screen"" size will give a wider distribution of ""Microtrac"" size when the particles are flaky with high aspect ratios, and a narrower distribution when the particles approach the cubical and spherical geometries.2 TheoryAustin and Shah [5] have shown that coal screened within a 1. 1/2 upper-to-lower sieve size range will give rise to a much wider distribution of Microtrac size. They found that the screen interval of irregular fragments of comminuted coals or quartz gave Microtrac size distributions which could be described by the simple function"

Jan 1, 1988

By Justin Carl, Aliuddin Mohammad, Gordon Evans, Steven Bealby, Carlton Ray

"The District of Columbia Water and Sewer Authority (DC Water) is implementing the $2.2-billion DC Clean Rivers Project (DCCR) to control combined sewer overflows (CSO) to the Anacostia and Potomac rivers and Rock Creek, and to provide flood relief to the Bloomingdale and LeDroit Park neighborhoods in the District of Columbia. The long-term control plan complies with the requirements of a Federal Consent Decree entered into by DC Water, the District of Columbia and the United States, as represented by the U.S. Environmental Protection Agency and the Department of Justice. The Northeast Boundary Tunnel, a design-build project, will store combined sewage and deliver it to a system of downstream tunnels and ultimately to the Blue Plains Advanced Wastewater Treatment Plant (Blue Plains), where it will be treated. In addition, the Northeast Boundary Tunnel (NEBT) is a major project associated with the mayor’s task force to alleviate extreme flood events in Bloomingdale and LeDroit Park. The Northeast Boundary Tunnel Utility Relocations (NEBTUR) design-bid-build (DBB) project is an accelerated component of the Anacostia River System, as shown in Fig. 1. During dry weather conditions, the entirety of the sewage in the combined system is conveyed to Blue Plains.During storm events, when sewer pipe capacity is exceeded, the flow, which is a mixture of sewage and stormwater runoff, overflows into receiving waters through outfalls. There are a total of 47 active CSO outfalls along district waterways.The influx of storm runoff into the combined sewer has an additional impact on the communities of Bloomingdale and LeDroit Park. The sewer system is outdated and undersized. In these neighborhoods, when the capacity of the sewer is exceeded, localized flooding occurs and backups into adjacent residences are prevalent. In any given year, there is a 50-percent chance that flooding will occur in these neighborhoods."

Jan 9, 2017

By D. Bienstock

Using a nitrided fused-iron catalyst, the Bureau of Mines investigated the Fischer-Tropsch reaction in the oil-circulation process. The nitrided iron was quite stable and permitted the longest run obtained thus far in the oil-circulation process without the need for reactivating the catalyst--3,700 hours of operation. The effects of several operating variables--temperature, pressure, gas-recycle ratio, space velocity, synthesis-gas composition, and synthesis with and without reflux of oil to the reactor--on the production of oxygenates were studied. The importance of removing reflux oil and of high gas recycle in increasing the oxygenate content was shown. A finished gasoline containing 28 percent by weight alcohols was produced. The research octane number (RON) was 92.9 clear, increasing to 98.5 with the addition of one milliliter of tetraethyl lead (TEL). INTRODUCTION The Federal Bureau of Mines has been engaged since 1944 in a research and development program on the synthesis of gasoline from coal. Gasification of coal with steam and oxygen to yield a "synthesis gas"--a mixture of carbon monoxide and hydrogen--is being investigated at Morgantown, W. Va., and the synthesis of gasoline by catalytically reacting carbon monoxide and hydrogen over iron by the Fischer-Tropsch reaction is being investigated at Bruceton, Pa.

Jan 1, 1960