Search Documents

By D. Antonov

The physical and mechanical properties of coal play a important role in the planing and design of coal mines. However, due to the complexity conditions in situ and the influence of unknown factors, it is hard for people to evaluate the physical and mechanical properties of coal directly. In this research, uniaxial compressive stress was used to change the attribute of coal samples, and the ultrasonic measure technique was used to evaluate the physical and mechanical properties of coal. The results of laboratory test showed that there was a strong relation between uniaxial stress and velocity of ultrasonic wave. Sensitivity analysis with numerical simulation was used to define the relation between the physical-mechanical parameters of coal and ultrasonoc wave. With the dynamic analysis module of FLAC, three elastic and plastic models were built to model the coal samples. The modeling parameters were changed pro rata, and the correlation of coal and ultrasonic wave properties were summarized and presented. The result from this research will be base for further analysis of caving behavior of coal.

Jan 1, 2010

By A. Romero-Juarez

This paper is concerned with the effect of propping-agent concentration on flow capacity of a fracture in the case in which there is embedment of the propping agent. Previous published studies have shown definitely that there is a relationship between fracture flow capacity and prop ping-agent concentration, and it has been shown that the theoretical results are confirmed by laboratory experiments. The problem of directly finding sand concentration for maximum flow capacity of a sand-propped fracture is solved, and formulas and charts are given to obtain this concentration under various conditions of effective overburden pressure, medium sand-grain diameter and rock properties. It is shown that, for the same effective overburden pressure and the same rock characteristics, optimum sand concentration in pounds per gallon does not depend on medium sand diameter. For conditions met in bydraulic fracturing operations, it is found that sand concentration in grains per square inch for maximum flow capacity varies within a wide range of values; this indicates the convenience of using data of fracturing pressure and rock characteristics for calculating sand concentration in order to achieve the best results in fracture treatments. INTRODUCTION It has been pointed out in the published literature1 that one important factor controls the success of a hydraulic fracturing operation — the propping of the fracture. The main effect of the propping agent is to hold the fracture open by means of the reaction forces that oppose the pressure due to the overburden. It is assumed in this paper that the propping agent is sand, that the grains are spherical and uniform in size, and that this sand is distributed in a monolayer in the fracture. The existence of a sand concentration value for maximum fracture flow capacity has been recognized since the publication of one of the first studies on the subject.2 In the reference cited, flow capacity was assumed to be proportional to the cube of the fracture volume per square inch not filled by sand. The obtained experimental curves relating to flow capacity and sand concentration had the same appearance as the curves obtained with the afore-mentioned assumption. Recent work3 has shown that fracture permeability, in the case of a monolayer, can be calculated accurately by means of a modified Kozeny-Cacman equation; thus, it can be shown that fracture pqmeability is a function of free volume in the fracture and of the rock and sand wet surfaces. The flow capacity of a fracture is dependent on the permeability of the fracture and on the fracture width. If all excessive quantity of sand is present in the fracture, its width may be large but its permeability i:; low due to the greater flow resistance; too few grains of sand per square inch are present in the fracture, sand embedment in the rock is greater and the width becomes small enough to appreciably decrease the rate of flow. To determine optimum conditions of flow, therefore, it is necessary to know the dependence of fracture width on density or concentration of propping agent. This relation is given in a study4 in which the approach to embedment is similar to the one made in a penetration hardness test of metal. With the equacions presented by Darin and Huitt,3 the number of sand grains per square inch that results in maxirnum fracture capacity can be determined graphically by plotting fracture capacity vs sand concentration. Since the relationship between fracture capacity and sand concentration may be considered known, one is led to formulate the analytical problem of directly determining sand concentration for maximum fracture flow capacity, in order to study the effect of the various quantities that come into the process. The solution of this problem appears to be interesting both from the viewpoint of fluid mechanics and from the practical viewpoint of oil production in hydraulic fracturing treatments. EQUATION FOR FRACTURE FLOW CAPACITY It can be shown3 that the fracture flow capacity of a monolayer is given by the following expression,

By P. J. Uggowitzer, K. Steinhoff, A. Wolf

"With the increasing acceptance of the Thixoforging process in the last few years, also the technical and commercial requirements for this forming technology and its components increased. So far, a great deal of work has been done in the development of an efficient process and control design. However, less attention has been paid to the development of new specifically tailored aluminum wrought alloys for this specific manufacturing process. · In this paper a new AlMgSi-alloy (A6082), optimized for the Thixoforging process, is presented. In the first part, the technical potential of the new alloy is specified by its microstructural evolution and flow characteristics in the semi-solid state. In the second part, the mechanical properties of thixoforged components of different conventional AlMgSi-alloys a (e illustrated · and compared to the new alloy.IntroductionSemi-solid metalworking, also known as semi-solid forming, is a hybrid manufacturing method that incorporates elements of both casting and forging. The key to the process relies on the peculiar flow behavior of slurries containing non-dendritic solid, which was first studied at the MIT by Flemings et al. [i], in the early 1970s. It was discovered, that if an alloy is uniformly stirred during freezing, discrete rounded particles of solid are formed rather than the normal dendrites, and the slurry is highly fluid (-5 Pas) up at least 50% solid. In addition, these slurries posses thixotropic flow characteristics: the viscosity is dependent on sheare rate and time. The more vigorously they are stirred, the more fluid they become. However, on standing the viscosity recovers and the material stiffens (-106 Pas).The semi-solid forming process exploits this phenomenon. In a first step, the required non-dentritical- microstructure is obtained by mechanical or electromagnetic stirring during primary solidification of the alloy. The stirred slurry is generally fully solidified as a feedstock billet and - in a second process step - reheated above the solidus temperature into the semi-solid state. In this condition, the thixotropic properties permit the material to be handled by robotic devices and transferred to a die (Thixocasting) or subjected to- a forming process by means of forging (Thixoforging). Owing to the shear stress which acts on the semisolid material during forming operation, the viscosity of the material is reduced attaining so the desired fluid-like flow characteristics."

Jan 1, 2000

By Douglas R. Cook

The discovery of the gold deposits of the Jerritt Canyon district, with proven recoverable reserves in excess of 67.6 Mg (2.4 million oz) of gold, has contributed greatly to the tremendous resurgence in exploration for disseminated gold deposits in Nevada and throughout the west. The Jerritt Canyon project, including the Bell mine, is a 70130 joint venture between Freeport Gold Co. and FMC Gold Corp., both of which are wholly owned affiliates of the respective parent companies, Freeport-McMoRan Inc. and FMC Corp. The Jerritt Canyon district is located in the center of the Independence Mountains in north-central Elko County, Nevada, approximately 48 km (30 miles) northeast of the Carlin gold mine and 68 km (42 miles) north of Elko. Although the discovery of a commercial gold mine at Jerritt resulted from Freeport's exploration activities, the initial identification of a gold prospect in this area was a consequence of a program by FMC in the search for antimony. Their program was, in part, based on data in the Nevada Bureau of Mines Bulletin 61, "Antimony Deposits in Nevada." Work on the property began in 197 1 with geologic mapping followed by sampling and geochemical analyses. FMC geologists, including Robert Hawkins, Russell Hayden, and Hal Hurst recognized the striking similarity of the area to the geologic environment of Newmont's nearby Carlin gold deposit and soon focused on the gold potential. Increases in the price of gold served to stimulate interest and support for the exploration program. Geochemical samples were collected and analyzed for gold and trace elements usually associated with gold. A strong gold anomaly was found on the North Fork of Jerritt Canyon, which was called the Alchem anomaly. Drill-testing of this anomaly in 1973 revealed significant grades and thicknesses of gold mineralization in the lower portion of the Roberts Mountain formation. This initial discovery and subsequent close-spaced drilling proved the existence of several small pods of low-grade, gold-bearing material which cropped out at their up-dip edges, causing the surface anomaly. The mineralization was very encouraging, but was not, by itself, of economic importance from the standpoint of either grade or tonnage. Freeport Exploration Co. established a district office in Reno in late 1974 with responsibilities for exploration of hard minerals in the Basin and Range Province. Emphasis of the program was directed to the discovery of precious metal deposits. Enfield Bell, as District Manager for this new office, was particularly interested in the Independence Mountains and when the opportunity for a joint venture with FMC became available in 1976, it was aggressively pursued. Enfield Bell and David Stevens evaluated the FMC data and with the support of management formulated a bid in competition with 23 other companies. Freeport was selected by FMC as partner and a joint venture agreement was successfully negotiated. In mid-summer of 1976, Freeport Exploration Co. began an expanded program of detailed mapping and geochemical sampling under the direction of Bell and Stevens that led to new interpretations of the structural and alteration patterns. Hawkins' contribution during this period must be recognized since he not only was one of the original geologists assigned to the antimony and subsequently the gold investigations, but shortly after the start of the joint venture exploration, he was hired by Freeport Exploration Co. as the project geologist for the venture. Hawkins had studied the central Independence Mountains for his thesis and his understanding of the regional geology provided an excellent background for the continued exploration of the gold de- posits. His interpretation of the structure in the vicinity of the Alchem anomaly was of significant help in the Freeport exploration program. Drilling, based on this new under- standing of the geology, revealed the edge of the Marlboro Canyon ore body, which is now being exploited in the Bell mine. Although a classic bullseye geochemical target led to the discovery of the Alchem mineralization, the bulk of the reserves known today in the Marlboro Canyon area lay

Jan 1, 1985

By Ray D. Peterson, Annette Revet

The optimization of secondary aluminum furnaces is critical to the efficient operation of a recycling facility. Since all metal loss occurs in the drosses, physical and chemical analyses of these by-products are valuable diagnostic tools. Dross analyses can provide information concerning total furnace metal recovery efficiency as well as identifying areas for potential improvements. A complete dross analysis is a labor-intensive process that requires significant care both in sampling and performing the analytical techniques. Experiments can be done at a bench- or plant-scale depending on the facilities available. This paper outlines the benefits and information that can be generated through dross studies. Furthermore, several analytical methods are discussed as well as the special requirements needed to gain accurate results. Experimental data from industrial studies is provided to demonstrate the use of dross evaluations for ~ace optimization.

Jan 1, 2000

By L. Tong, D. Robinson

"The stirred milling of nickel laterites offers possibilities for improving liberation and selective size reduction of soft nickel-bearing minerals in laterites. Batch grinding tests were performed in a netzsch™ lME4 stirred mill on siliceous goethitic, goethitic, and saprolitic nickel laterites. Tests on the -2,000 µm sample displayed the effects of selective comminution. The -38 µm product of grinding the -2,000/+38 µm feed confirmed the effects of selective grinding and nickel upgrading. Size classification followed by stirred milling is recommended for nickel upgrading. The energy requirement in the stirred milling was also investigated.RÉSUMÉ le broyage par billes de latérites comportant du nickel offre des possibilités d’amélioration de la libération et de la réduction sélective de la taille des minéraux nickélifères tendres dans les latérites. Des essais de broyage en vrac ont été effectués dans un broyeur à billes netzschMD lME4 sur des latérites nickélifères à goethite siliceuse, à goethite et saprolitiques. Des essais sur l’échantillon -2000 µm présentaient des effets d’une comminution sélective. le produit -38 µm de l’alimentation -2000/+38 µm confirme les effets d’un broyage sélectif et du rehaussement de la teneur en nickel. Pour améliorer la teneur en nickel, il est recommandé de classifier le minerai en fonction de sa granulométrie, puis d’effectuer un broyage à billes. l’énergie requise pour le broyage à billes a aussi été étudié."

Jan 1, 2015

By David Preece

The Thirlmere aqueduct was constructed over 110 years ago to provide water from the Lake District (in the north-west of England) to the city of Manchester some 60 miles (100 km) away. The aqueduct remains, to this day, a key piece of infrastructure in the distribution of raw water in the north-west of England. A short section of the aqueduct was identified as being in poor condition during routine inspections by the owner. Subsequent investigations attributed the conduit damage to the movement of unstable ground over the conduit. Bachy Soletanche Ltd was subsequently appointed to carry out the design and construction of the slope stabilisation works and to undertake repairs inside the damaged conduit. The works were undertaken on an existing slope which, in places stands at a gradient of up to 40º to the horizontal. Strict limitations on plant and equipment were imposed by the client (United Utilities) to ensure that slope and conduit loading and associated vibrations were kept to an absolute minimum during construction. An intensive instrumentation system was installed to monitor surface movements, ground movements at depth, conduit movement and strains across existing planes of weaknesses within the conduit. The solution comprised the installation of spaced piles up-slope and down-slope of the conduit. Restrictions were imposed on the minimum stand-off distance between the outside face of the conduit and the piling works so targeted permeation grouting was undertaken to improve the ?connection? between the conduit and the down-slope piles. The presence of existing sub conduit groundwater flows was suspected and the permeation grouting was focused in areas to minimize disruption to the groundwater regime. The paper presents the basis of the design and highlights the combined construction and instrumentation methods adopted to minimise damage to this valuable asset.

Jan 1, 2011

By J. B. Newsom

SAFER, cheaper, and faster sinking of mine openings seems to have been realized with the completion of a borehole 5 ½ ft. in diameter and 1208 ft. deep, in Minnesota, during 1938. Moreover, as the opening is to be used solely for ventilation, its circular cross section, smooth walls and freedom from fire hazard recommend it in comparison with the usual timbered shafts of rectilinear cross section. It should be pointed out that a drill hole sunk without the use of explosives frequently will stand open without support, whereas a shaft sunk by standard procedure using dynamite usually must be timbered because of the wall-shattering effect of explosives. The saving in maintenance resulting from the elimination of timber is obvious. The work was done by Pickands Mather & Co. at its Zenith mine, Ely, Minn. This company wanted a ventilation opening capable of delivering 50,000 cu. ft. of air per minute to the fourteenth level, 1200 ft. below the surface. While several general articles1-3 have described the method used, detailed time and performance records have not been presented before. Moreover, with a method as new as this, it is important to compare the results attained under widely varying conditions. Among the new conditions faced at Ely were some extremely hard rock, a series of vertical fractures, seepage water, and some long stretches of sound rock which, combined with excellent equipment, gave a chance to operate without unusual delays. Developments in boring large holes have generally taken the obvious course of increasing the size of the equipment, a line of attack that has resulted in putting down 3-ft. diameter holes at damsites for studying the foundations4 and in drilling ventilation openings between levels at Butte. 5 Such drills operate from the collar of the hole, and the power from the drill is transmitted to the cutting tool through drill rods or pipes. In order to keep down the volume of rock that must be ground to sludge, the cores in large-diameter drilling are made as large in diameter as possible. Their large diameter increases their weight per foot of length, which

Jan 1, 1939

By M. Z. Emad, A. Hassan, M. A. Raza, M. U. Khan, S. A. Saki

Digital modelling of a surface is crucial for Earth science and mining applications for many reasons. These days, high-tech digital representations are used to produce a high-fidelity topographic surface in the form of a digital terrain model (DTM). DTMs are created from 2D data-points collected by a variety of techniques such as traditional ground surveying, image processing, LiDAR, radar, and global positioning systems. At the points for which data is not available, the heights need to be interpolated or extrapolated from the points with measured elevations. There are several interpolation/extrapolation techniques available, which may be categorized based on criteria such as area size, accuracy or exactness of the surface, smoothness, continuity, and preciseness. In this paper we examine these DTM production methods and highlight their distinctive characteristics. Real data from a mine site is used, as a case study, to create DTMs using various interpolation techniques in Surfer® software. The significant variation in the resulting DTMs demonstrates that developing a DTM is not straightforward and it is important to choose the method carefully because the outcomes depend on the interpolation techniques used. In mining instances, where volume estimations are based on the produced DTM, this can have a significant impact. For our data-set, the natural neighbour interpolation method made the best predictions (R2 = 0.969, β = 0.98, P < 0.0001).

Feb 6, 2023

By Christian Neumann, Josef Arnold, Albin Reinhart

The Channel Tunnel Rail Link (CTRL) is the most significant railway infrastructure development project in the United Kingdom since the construction of the Channel Tunnel between France and England. The key element of this project is the 2-mile-long(3.2-km) North Downs Tunnel, which will be the largest and deepest twin-track railway tunnel ever constructed in the United Kingdom. This paper describes the contractual agreement, the design and construction (excavation and lining) of a twin-track rail tunnel with a 166-m 2 face excavated through chalk using the New Austrian Tunnelling Method (NATM). The importance of collaborating with a tunnel contractor/designer who not only is expert in the New Austrian Tunnelling Method, but who was also responsible for the design and installation of the primary lining, will be highlighted in this paper. This paper will also deal with the benefits of partnering in tunnel design and construction, as well as the resultant added values of mechanizing conventional tunnelling methods (Value Engineering).

Jan 1, 2001

By J. S. Marsh, T. B. Winkler

THE past year, the first full one of peacetime production, proved that the process of beating swords into plowshares has increased in complexity in step with civilization. Further, judging by various remarks of our distaff departments, the crystal balls of certain radio and magazine oracles must have been cloudy, because we have been in formed from time to time that coveted items such as automobiles and refrigerators did not appear in great abundance. This seemingly extraneous matter is really not out of place here, however; the steel producer and the fabricator exist in a sort of symbiosis: the making of consumer goods produces scrap which is returned to the steelmaker who makes more steel, and so on and so forth. Thus, no abundance of automobiles, no abundance of scrap from this normal source; and other sources had been picked pretty clean during the war. To be short, so was scrap. Since the economy of the steel industry lean; as heavily upon iron from scrap as upon iron from ore, the statement on transformation of swords to plowshares follows. But this is not the whole story: after all, ingot production was a record for a peace year!

Jan 1, 1947

By Barun Gorain, Aparup Chattopadhyay

"Many double refractory gold deposits are characterized by the dominance of ""invisible gold"" (sub-microscopic gold) as solid solution or as colloidal-sized particles in different sulfides and other phases. These deposits are mainly composed of silicates and carbonates with moderate clay and mica content and with minor amount of sulfides and organic carbonaceous matters. The presence of highly preg-robbing and finely disseminated carbonaceous matter adversely affects gold recovery in leach circuits. Characterization of carbonaceous matters, commonly known as TCM and quantification of gold associated within these carbonaceous matters along with different sulfide and oxide phases is highly complex and challenging. Studies were initiated on various complex ore deposits and also on samples representing various process streams. This paper presents the development of a systematic approach to gold deportment studies using state-of-the-art mineralogy characterization techniques for quantification of invisible and visible metal contents in various species. The relevance of this mineralogy characterization to metallurgy will also be discussed in this paper."

Jan 1, 2014

By Robert L. Lagace

This final report documents the work dune by Arthur D. Little, Inc. (ADL) on behalf of the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center (PMSRC), on Contract H0122026 (which began in August of 1971). Under this contract ADL provided technical assistance to the Bureau on a task basis on virtually all aspects of the Bureau&apos;s programs related to present and planned emergency and operational communications and miner location systems for underground coal mines. The work consisted of independent investigations, analyses, experiments, breadboard and prototype hardware development, workshops and technology transfer seminars on mine communications, and on-going evaluations and guidance related to the Bureau&apos;s contracted programs on electromagnetic noise, mine communications systems, and trapped miner location. This final report documents the work in two volumes, Volume I, "Emergency and Operational Mine Communications," and Volume II, "Seismic Detection and Location of Isolated Miners." The Tables of Contents of both Volumes are included in each Volume. Phase I of the contract was devoted to performing an in-depth assessment of electromagnetic noise measurements taken by several contractors and other investigators, and then defining a new noise measurement program and instrumentation system tailored to obtain the necessary but missing noise data. These data are required for use in the design of new emergency and operational communication systems. This work, and the follow-on coordination and guidance activities of ADL on this noise measurement program in subsequent phases of the contract, are treated in Part One of Volume I.

Jan 1, 1974

By T Medhurst

Recent developments in geophysical borehole log analysis using the Geophysical Strata Rating (GSR) are now routinely used in a number Australian coal mining operations. This allows development of 3D geotechnical strata characterisation models for a range of purposes. The availability of this data provides a means to identify relationships between ground conditions and ground behaviour. As a result, several new design methods have been developed to assist in the strata management process such as roof support, longwall shield design and shaft stability assessment. This paper outlines these methods and provides examples of their application. CITATION:Medhurst, T, 2018. Geotechnical strata characterisation using geophysics and its application for coal mine design, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 420–433 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By C. J. Tonkin

Compressed air is widely used on South African gold mines. However, due to recent and proposed future electricity tariff increases it is quickly becoming too expensive to produce and use. Boxfront chute systems at ore passes were focused on during this study, and a number of alternative power sources were examined. After comparing primarily costs, and secondarily safety and practicality, of a number of systems based on water and hydraulic oil, a system making use of either air or water was determined to be the most cost effective. A payback time of 8 years was calculated, which will be significantly less taking into account the avoidance of failures due to electricity and water shortages, which would not affect this system due to its ability to swap between either air or water. It was recommended that this system be installed at all boxfront chutes as soon as possible so that the company can begin to benefit from the cost savings.

Jan 1, 2013

By E. C. Nelson

An equation is derived for calculating approximately the solubility of nitrogen in an alloy steel over a temperature range from 1200" to 1900°C using data on the effects of alloys on the activity coefficient of nitrogen in iron at 1600°C. Calculated values are compared with experimental data. STUDIES involving the solubility of nitrogen in complex iron alloys have been aided by a system devised by Lanenberg for calculating the solubility of nitrogen in ternary and higher alloys of iron at 1600C using available data on the activity coefficient of nitrogen in binary alloys. Calculated nitrogen solubilities agree well with experimental determinations on complex alloys,&apos; and the calculation procedure is useful when experimental data on specific alloys are not required. A method for extending calculations of nitrogen solubilities in alloy steels to temperatures other than 1600°C would be useful because of the paucity of experimental data in this area. Assumptions which must be made to permit this calculation introduce an element of approximation; however, the calculation is useful in cases where a large number of alloys and temperatures are under consideration, and the precision of experimental measurements is not required. The activity coefficient can be freed from the isothermal restriction of Langenberg&apos;s calculation if it is assumed that the solution is "regular". This is a reasonably good assumption for solutions of nitrogen in iron alloys, because usually they are dilute and the heat of solution is relatively small. The presence of large amounts of certain alloying elements would make this assumption less tenable.3 One of the properties of a regular solution is: when "f" is the activity coefficient of a solute and "T" is the temperature in OK. If the activity coefficients at temperatures T and T2 are denoted by subscripts 1 and 2 respectively: The activity coefficient of nitrogen in a complex alloy then can be calculated at any temperature from the sum of the effects of the other solutes on the activity coefficient of nitrogen at 1600°C. It will be convenient to incorporate this expression into an equation which will give directly the logarithm of the solubility of nitrogen at any temperature in the presence of alloys. Two constants, the solubility of nitrogen in pure iron at 1600 "C and the partial molar heat of solution of nitrogen in iron are required. The heat of solution value of 1400 cal at 1600 °C quoted by Kubaschewski and vans will be used. The accuracy of the calculation will suffer if the heat of solution should change materially with temperature. In the absence of experimental data on the temperature dependence of this quantity, it will be expedient to restrict the application of the calcula-

Jan 1, 1963

By Gary L. Hundley

The Bureau of Mines has devised a procedure to recover chromium chemicals from low-grade domestic chromites, which contain silicon and aluminum impurity levels that are too high to permit processing by present industrial processes. The Bureau procedure consists of reacting chromite with molten sodium hydroxide (NaOH) under oxidizing conditions to form sodium chromate (Na2Cr04). The reaction product is leached with methanol to remove the majority of the unreacted sodium hydroxide, then with water to remove the sodium chromate and the remainder of the sodium hydroxide. The sodium chromate product is recovered by evaporative crystallization from the aqueous solution. This report presents results of laboratory tests to determine the optimum fusion conditions and the chromium extractions obtained from several domestic chrotdte concentrates. These concentrates are from a variety of sources, including the Stillwater Complex in Montana, Kanuti River-Caribou Mountain, Red Bluff Bay, Kenai Peninsula, and Kodiak Island areas in Alaska, deposits in northern California, and a nickel-cobalt laterite from southern Oregon. All of these concentrates were successfully treated by the Bureau procedure. The best chromium extrac-tions obtained for each of these materials ranged from 69.5 to 98.9 pet.

Jan 1, 1985

By Matthew E. Eisenmann, Gerald H. Luttrell

Performance data from phosphate plants are often untrustworthy because of difficulties associated with highly variable feeds and unstable equipment operation. In some cases, this problem is further compounded by improper sampling procedures and unreliable laboratory analyses. Questionable data often lead to misleading conclusions that result in lost productivity and profits. Data reliability may be checked using mass balances, but the mathematics associated with this procedure can be overwhelming when multiple data sets or complex circuits are evaluated. To overcome this problem, a simple spreadsheet-based mass balance program has been developed specifically for plant operators. To use this program, operators simply enter a description of their circuit and input the assay values (e.g., % BPL, % Insol, etc.) for each stream. The program then generates the best estimates of the assay values and flags values that may be unreliable. The spreadsheet is specifically designed to be easy to use and requires no knowledge of statistics or programming. This manuscript reviews the mass balance problem and describes how spreadsheet programs can be used to evaluate plant data. An example problem involving the analysis of data around a two-stage phosphate flotation circuit is presented.

Jan 1, 2002

By B. P. Sereda

The properties, characteristics and phase structure of chamotte refractories produced with the usage of mullitecorund chamotte and caoline have been given. The comparison of new refractory C-45 obtained by us and refractory C-43 produced by traditional method has done. The physical-chemical properties of refractories is reviewed. The visual porosity, density and pore characteristics of given refractories was calculated. It is established that C-45 has the less gas permeability then C-45 that gives melting units more stability. The petrographical microstructures of refractories have been done. The main phase structures and their influence on refractories properties have been observed. It is established that refractories with mullitecorund chamotte adition has more advantages then refractories gained by traditional method and can be applied to melting units.

Jan 1, 2010

By MARK J. VANARELLI

Estimating groundwater inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies for estimating steady-state groundwater inflows into deep rock tunnels. The case studies included the Chattahoochee and Nancy Creek tunnels. In this paper, statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations. A semi-empirical procedure was utilized for estimating groundwater inflows into these deep rock tunnels. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels which exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semi-empirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Packer test data plotted in histograms were observed in all cases to be log-normally distributed for the radial flow condition. Modeling using Monte Carlo simulations was observed to be an effective tool for removing irregularities in the distribution of the data and incorporating high-end permeability data to derive reasonable groundwater inflow estimates.

Jun 13, 2021