Search Documents

By W B. Gregg

The rock blasting and mining industries use a system of detonators and explosives for mining operations. Many detonators use small metal bridgewires, which are heated by passing a current through the wire, heating and igniting the pyrotechnic powder in contact with the wire. Typical bridgewires require a current of at least 3 amps, applied for a few milliseconds, for an explosive output. The semiconductor bridge (SCB), in comparison, initiates an explosive in 0.01 to 0.1 of a millisecond.

Jan 1, 1994

By S. Xu

Magnesium alloy AM50 is of interest to automotive cradle application because of it excellent castability and good ductility. In this work, microstructure and mechanical properties of both low pressure die cast (LPDC) and high pressure die cast (HPDC) AM50 test bars are characterized. Microstructure was examined using optical microscope, scanning electron microscope (SEM) and transmission electron microscope (TEM). Phase identifications were performed using energy dispersive x-ray spectrometer (EDS) and TEM diffraction. It has been found that LPDC produces much coarser microstructure than HPDC. At the same time, the HPDC samples are more heterogeneous in microstructure and composition close to grain boundaries. Particles with various dimensions and morphologies of two different intermetallic phases, Mg17A112 and A18Mn5, were found in all the samples. Mechanical tests were performed under conditions similar to those related to an engine cradle application. LPDC samples show lower strength but better creep resistance than HPDC mainly due to the difference in grain sizes and grain boundary microstructure between LPDC and HPDC. Creep curves are well described by the empirical Andrade equation. Tensile-compressive yield and creep asymmetries were found in AM50, i.e. better deformation resistance in tension than in compression. The average yield asymmetry ratio for all the samples is 0.87. Microstructural examinations on the samples tested in tension, compression and creep showed that the deformation mechanisms in AM50 were slip plus twining at temperatures up to 125°C. The examinations indicate the important role of twining in the asymmetry phenomenon. The creep results indicate that dynamic precipitation of the Mg17A112 phase during testing is not the mechanism directly responsible for the creep asymmetry in AM50.

Jan 1, 2004

By Vinícius da Silva Madruga

Os processos de lingotamento contínuo e de lingotamento convencional apresentam diferenças na solidificação dos aços, esse fato tem impacto na distribuição, quantidade e forma de inclusões de óxidos e sulfetos. O objetivo desse trabalho é verificar de que maneira tais diferenças influenciam na distribuição dos sulfetos ao longo do aço solidificado de qualidade SAE 1050. Para isso, 20 amostras foram retiradas de eixos forjados e barras laminadas, produtos conformados de origem do lingotamento convencional e do lingotamento contínuo, respectivamente. As amostras foram analisadas em microscópio ótico e microscópio eletrônico de varredura no modo de análise automatizada de partículas. Através das imagens e de dados numéricos obtidos, foi visto que nas amostras de barra laminada há grande quantidade de sulfetos, se analisada na seção longitudinal, em relação às amostras de eixo forjado. Analisando na seção transversal, foram detectados menos sulfetos devido ao alinhamento dos mesmos. Entre as amostras de eixo forjado, a área ocupada pelos sulfetos é maior no pé do lingote, reduzindo em direção à cabeça, apesar de a cabeça apresentar mais sulfetos. Tais diferenças foram atribuídas à taxa de resfriamento, à seção transversal do produto e ao processo, que variam entre os dois tipos de lingotamento.

Oct 30, 2017

By Andrew W. Jenike

There used to be a time when bins were designed for total volume and placed in any available place of the plant. Poke holes were provided and feed was maintained by manual prodding, lancing, hammering, and by various mechanical flow-profiting devices. Little thought was given to what occurred inside the bins and why materials did not flow. Indeed, such mental effort was hard to justify while low-cost manual labor was plentiful, quality standards low, and rates of feed moderate. The past fifteen years have seen a drastic change in these conditions. We all know that labor for hard manual work is becoming unavailable at any wage, level. Standards of product uniformity are continuously rising. This uniformity is just as important in a fine ore feed to ball mills as it is in a cattle feed or in a flour mix. Rates of feed now frequently exceed 2,000 tons per hour per feeder. At that rate there is no time for, lancing or prodding. An efficient storage, plant contains a known available volume of bulk solid, and feeds it at the required time, at the prescribed rate, and without degradation of the product. A storage bin may also perform other functions such as blending of different grades, degasification of aerated, powders, isolation of different gaseous media. A contact bed of particles flowing by gravity in counter-current with a gas or liquid may be used as a continuous reactor. Gas or liquid pressures can be simply contained by, a sufficient head of flowing solid.

Jan 1, 1968

By Jean-Christophe Ehrström, Fanny Mas

"A specific test set-up has been developed to study at the lab-scale the high-temperature behavior of aluminium alloys in conditions close to those experienced by thick plates during hot-rolling. A particular attention is paid to reproducing both the stress triaxiality and strain fields that exist in plate during rolling. In addition to standard ductility measurements by means of secondary tensile tests (STT), multi-step plane strain compression (PSC) tests have been performed to mimic hot-rolling pass schedules. Tool and sample geometries were adapted to allow low h/a ratios (h= average specimen thickness, a= tool width) and thus guarantee depressive stress conditions at the center of the specimen during most of the test. Such conditions resulting in porosity opening can then be used to investigate the impact of rolling conditions on damage evolution. The mechanical testing was combined with post-mortem high-resolution ultrasonic scans allowing to detect small amounts of damage and quantify its evolution as a function of processing parameters such as strain and temperature. The test set-up was validated on two 2050-type AlCuLi alloys with different susceptibilities to high temperature embrittlement.INTRODUCTION Aluminium thick plates are widely used in the aerospace industry, mainly as semi-products to be machined for internal structure parts of wings (spars, ribs) and fuselage (frame). The conversion route of such products always involves a hot-rolling step, the conditions of which (temperature, speed, pass schedule) have to be optimized to maximize both mechanical properties and final plate quality. This goal cannot always be efficiently achieved by full-scale industrial trials as (a) cost limits the number of possible test conditions and (b) it is often difficult to change one parameter alone. That is why there is a need for laboratory-scale tests able to mimic the rolling process in terms of temperature, strain rate, stress triaxiality and deformation. Most laboratory hot-rolling mills do not adequately simulate industrial processing routes, especially in terms of heat loss, deformation speed and rolling geometry (maximum roll gap vs. work roll diameter). Concerning thick plate, it is of interest to achieve both similar deformation and L/h ratio (L=arc of contact, h=mean gauge) per pass as the industrial schedule because they are simultaneously involved in damage evolution and void closure during hot forming processes (Saby, 2014)."

Jan 1, 2018

By Raymond A. Binns

Exploration for undersea polymetallic sulfide mineral resources with high economic potential would be more effective given an ability to predict sites with particularly high gold contents (averaging say > 10 ppm Au). Herzig et al (1993) addressed this issue shortly after recognition that deposits in the back-arc Lau Basin (average 3.8 ppm Au) were enriched in gold relative to mid-ocean ridge sites (average 1.2 ppm Au). Small but significant numbers of hydrothermal sites with massive sulfide deposits averaging >10 ppm Au have since been discovered. The principal genetic factors underlying gold enrichment include depositional processes at and below the seabed, and the source of gold. It is timely to consider whether resolution of their relative importance can be translated into practical criteria for exploration strategies focused on especially gold-rich deposits. Comparing the ?grade? of seafloor deposits using analyses cited in research papers is fraught with difficulty, but there is no alternative at present to assuming that such averages provide an initial tenor guide. On this basis, four known polymetallic hydrothermal sites from convergent plate margins fit the exceptional-gold category with >10 ppm ?average? Au, while one from a divergent margin comes close: Sunrise (Myojin Knolls; 20 ppm ?average? Au) and Suiyo Seamount (28 ppm Au) in the Izu-Bonin Arc are frontal arc volcanoes dominated by rhyolite and dacite respectively, contrasting with more common mafic neighbor edifices (Iizasa et al., 1999). In both cases gold-rich massive sulfides occur in summit calderas with significant development of pumiceous volcaniclastic rocks, at depths around 1300 and 1370 m respectively. In the Eastern Manus Basin, PACMANUS (~1700 m; 14 ppm Au) and Suzette (~1550 m; 22 ppm Au) occur along the crests of volcanic ridges dominated by dacite/rhyodacite and andesite/mafic dacite respectively (Binns, 2004). Caldera structures are lacking. Although the Eastern Manus Basin is tectonically a rifted back-arc, its submarine volcanic edifices (picritic basalt to rhyodacite) have distinctly arc-style geochemical and isotopic affinities, differing from more typical back-arc basin basalts at the spreading axis further west (central Manus Basin). Probably as a consequence of transpression and a marked rupture in the New Britain subduction zone, submarine arc volcanism has here extended into the rifted back-arc region.

Jan 1, 2005

By Phillip E. Glogowski, N. Catherine Bazan-Arias

Steel foundations can be designed to cross-sectional configurations ranging from triangular and square to other multi-side shapes. Adding lateral extensions (hereby called wings) along the length of the steel stem can increase the foundation’s uplift, torsional and lateral load capacities. DiGioia Gray staff developed a methodology for the optimal design for multi-facetted, winged deep steel foundations. A finite element (FE) model is used to represent the steel components and the nonlinear subsurface behavior. The geometry of the foundation can be complex; thus, an optimal design needs to be fine-tuned to the specific site conditions. We created a pre-processor tool to generate the FE model including varying values for the number and size of wings, depths of embedment, reveal/stickup heights, top plate geometries, and subsurface profiles. The analytical model has been partially validated through full-scale testing and the methodology has been applied to two installed projects to date.

Sep 8, 2021

By J. Sjöberg, T. Savilahti, S. B. Umar

"Sublevel caving in Malmberget mine results in mining-induced surface deformation. One of the currently mined orebodies is the Printzsköld orebody. As mining deepens there is need to assess the behaviour of the cave formed in the subsurface above this orebody. Numerical analysis was used to assess the effects of extraction to deeper levels and perform strength parametric studies. Stress redistribution was studied, and the results showed high stress buildups in the hangingwall and the crown pillar. Two failure mechanisms have been identified – shear and tensile. Reducing cohesion by 50% increased the area of the yielded zone by more than 100% in the hangingwall.IntroductionThe Malmberget mine is owned and operated by the Luossavaara-Kiirunavaara AB (LKAB) mining company. Iron ore is extracted by large-scale sublevel caving. The mine comprises a total of 20 orebodies, about 10 of which are in production today (Figure 1). The mine is located in the municipality of Gallivare, about 100 km north of the Arctic Circle (Figure 2).Successful sublevel caving requires progressive caving of the orebody after initial blasting. This results in caving of the hangingwall, sometimes all the way to surface, resulting in surface deformation. As mining progresses to deeper levels a larger area is affected by deformation. Over the years, extraction from the Malmberget orebodies has led to deformation of the ground surface, affecting residential areas and existing infrastructure.Forecasting the caving process is not straightforward as it can be rapid or slow, depending on the rock mass conditions, stress conditions, the failure mechanisms at work, etc. Moreover, several of the orebodies in Malmberget are non-daylighting, which makes reliable caving analysis even more difficult, primarily since there is less available experience from such cases. The present study was designed to improve the understanding of the caving and deformation mechanisms at Malmberget, and in particularly for the Printzskold orebody"

Jan 1, 2017

I BELIEVE that my work would surely be host a seed without fit and that I would fail in that cause which disposed me to satisfy your request to write and form this work [75] if while laboring on it I did not tell you of the art of casting, since it is a necessary means to very many ends. I realize even more that I must tell as much as seems necessary since I have already demonstrated the methods of recognizing the natures and locations of the metals, of smelting and reducing them to their ultimate perfection, and finally have taught you to make their associations and alloys. It is especially necessary since this art and work is not well known, so that no one can practice it who is not, so to speak, born to it, or who does not have much talent and good judgment. For this reason and also because it is closely related to sculpture, whose arms are the support of its life, it is very highly esteemed. In order to describe the whole art in every part, I say that the greatest labors of both mind and body are required for its operations in the beginning, middle, and end. It is indeed true that these labors are endured with pleasure because they are associated with a certain expectation of novelty, produced by the greatness of art and awaited with desire, particularly since the artificer sees that it is an art pleasing and delightful even to ignorant men. As a result, as if ensnared, he is often unable to leave the place of work. To conclude: The outcome of this art is dependent upon and subject to many operations which, if they are not all carried out with great care and diligence and well observed throughout, convert the whole into nothing, and the result becomes like its name [cast away]. Therefore, having considered this work many times, with its extraordinary obstacles and the bodily labors heavy as a stevedore's, instead of exalting it with praise, I wish to say that it is such that a man of noble birth, even though he be gifted or be drawn to it by pleasure, should not practice it and could not unless he is accustomed to the sweat and many discomforts which it brings. He must suffer the great natural heats of summer as well as those excessive and continuous ones from the enormous

Jan 1, 1942

By Shantanu Chakrabarti, Khursid Alam Khan

"Globally, the use of metallic coated steel sheets in the automobile industry is increasing. The sheet should have excellent formability, weldability, paintability and corrosion resistance. Since bare cold rolled steel sheets have certain limitations, application of galvanized steel sheets is steadily expending. Galvannealed steel sheet fulfills all requirements and has become of major interest in the automobile industry.The success of Galvannealed (GA) steels in the body-in-white depends upon material design and parameters of various processes involved, like cold rolling, continuous annealing, hot dipping and galvannealing. In the present work, powdering resistance, one of the important product characteristics of GA, has been studied and a relation is established between the process parameters and the powdering value. The product obtained through optimization of the process parameters have been successfully used by major automotive producers without any powdering problem, for internal as well as external automotive applications.IntroductionThe present automotive industry demands that steel for the auto components should have excellent formability, weldability, paintability, corrosion resistance etc. In addition to this there is specific requirement for some particular components like high surface quality for skin panels. Corrosion resistance of panels is important requirment which determines the life of the particular component and brand value of the automotive. Among all the zinc based steel coating used in the automotive industry coating produced by Galvannealing process has received most attention because of its excellent weldability along with superior corrosion resistance and better paintability."

Jan 1, 2012

By C. R. Austin

THE investigation described in this paper deals with the development of high-temperature alloys of the Konel series over a considerable period of time at the Research Laboratories of the Westinghouse Electric and Manufacturing Co. The word "Konel" has been coined to designate a class of alloys which are essentially nickel-cobalt-iron with other elements added, usually in small quantities. Most of these alloys contain titanium, usually about 2.5 percent. The main consideration related to strength at high temperatures but the thermionic characteristics of the alloys was also of considerable importance. It is, however, with the mechanical properties at elevated temperatures that we are herein concerned. Much attention has also been devoted to their age-hardening characteristics. There is little need to stress the utilitarian aspect of this subject, as it has been discussed frequently. Alloys exhibiting superior properties at normal or elevated temperatures rapidly find many suitable applications. There may be some question, however, as to what constitutes a "superior alloy, " or an alloy that may have good service possibilities at high temperatures. The problem is complex and various means have been employed to predict the useful life that may be expected of a material. In recent years the "creep limit" has been used as the best means of evaluation. Such tests necessarily are prolonged and hence collection of data is very slow. In a general survey of many alloys therefore the creep test is not desirable and recourse must be had to much shorter time tests in order more rapidly to select alloys which appear to show promise. For this reason the present survey has been made using the high-temperature tensile test and a bend' test developed by Howard Scott.1 In the tensile test the conditions have been standardized for all tests, so that values obtained are at least comparable, one alloy with another, although the absolute values recorded merely indicate the mechanical properties at the given temperature under a definite rate of loading.

Jan 1, 1931

By J. Gao, H. O. Gekonde, S. V. Subramanian

"The functional role of inclusions at low cutting speeds is to promote ductile fracture in chip formation process, whereas the role of inclusions at high cutting speeds is to prevent tool crater wear by suppressing the tribological phenomenon of seizure at the tool-chip interface. Glassy oxide inclusions are engineered into the workpiece to form a viscous layer in-situ at the tool-chip interface at high cutting speeds. The viscous layer lubricates the tool-chip interface to prevent the seizure. In comparison with the large volume fraction of inclusions needed for promoting ductile fracture at low cutting speeds, the amount of inclusions required for lubricating the toolchip interface at high cutting speeds is very small and is in the range that is typical of clean steels. The chip fracture process at high cutting speeds is aided by strain rate hardening of the matrix, which facilitates chip disposal of relatively clean steel.Inclusion engineering for high speed machining involves the control of the rheology and composition of inclusions to meet target viscosity at the tool-chip interface. The application of thermodynamic models in controlled production of inclusions in steels designed for high speed machining is discussed."

Jan 1, 1998

By Douglas G. Hubert

To put coal in its proper perspective as a source of energy for electric power production, we must first compare it to other energy sources. A report of the Atomic Industrial Forum dated February 1958 records a number of authoritative though widely varying predictions. The most optimistic of these states that by 1968 there will be a total U.S. capacity of about 6000 megawatts of nuclear power, if growth continues at the present rate. Other sources indicate over 200,000 megawatts of total electrical capacity in utility plants by 1968. This is only 3% nuclear. Therefore, 97% of our total power production will be from non-nuclear energy. Fig. 1 shows the distribution of energy sources of electric utility product- ion in the U.S. as reported by the Federal Power Commission in 1954. Note that less than one quarter of the total is hydro and about one half of the total is coal. For 1957, the Edison Electric Institute reports that of the total steam- electric generation in the U. S., 68.6% was by coal, 7.9% was by oil and 23.5% was by gas. This is an increase for coal and a decrease for oil and gas in those three years. Thus we can conclude that two-thirds of the steam-electric power in the U. S. is now generated by coal. Fig. 2 shows the major markets for coal for 1947 vs 1957. The greatest in- crease has been in the electric utility market, where it has more than doubled in the ten years. One-third of the total coal produced goes to the utilities which now represent coal?s major market. Utilities used 160 million tons of coal in 1957, and the estimated quantity for 1967 is 275 million tons, and for 1977 is 525 million tons. It is predicted that 85% of steam-electric power will be generated by coal in 1975.

Jan 1, 1959

By Brendan Demich, Joseph McGuire, Emily J. Haas

Near misses recorded and reported by workers can provide awarenessto the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, it is unclear what the value of these reports are, if any, and how they influence subsequent actions or controls to reduce on-the-job risks. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. Of those, 167 were valid near misses that occurred at work. Researchers coded the reports using a qualitative 5 × 5 risk matrix. Of the 167 near misses, 19% were deemed low risk, 25% moderate risk, 30% high risk, and 26% critical risk. Several patterns in the near-miss incidents were documented, including classification of incidents and common corrective actions referenced (i.e., elimination/substitution, engineering control or redesign, work process/procedures, and personal protective equipment). The analysis provides insight into ways that risk communication and management programs can be improved to reengage workers and their situational awareness on the job.

By Francois Barthelat, Sam Goroshin, David Frost, Alexander Cappozi, Atefeh Nabavi

"In this study, a novel chromium–chromium sulfide cermet was produced by self-propagating high-temperature synthesis (SHS). Conventional techniques for manufacturing metal sulfides are complex, environmentally harmful, and not suitable for producing complex-shape articles. To overcome these disadvantages, a new method for the preparation of the metal-sulfur precursor charge is proposed, which can be described as reactive casting. The first cermet samples produced with the SHS process were found to be very porous, brittle, and have low mechanical strength. The possible sources for the generation of porosity were identified and analyzed and the process for manufacturing the cermet was modified. By improving the manufacturing process, the porosity inside the produced cermets was reduced from 70% to 12%.IntroductionMetal sulfide composites are in high demand in the chemical, metallurgical, and electrical industries because of their valuable characteristics such as hardness, semi-conductivity, electroluminescence, infrared transparency and catalytic properties. Current manufacturing methods for metal sulfides usually involve one of two different principal methods, including a complex multistage wet chemical process involving the precipitation of the corresponding salts from an aqueous solution with hydrogen sulfide, or hot sintering of the respective elemental reactant powders in a resistive furnace in a high-pressure inert or hydrogen-sulfide atmosphere [1, 2]. These conventional methods for synthesizing ceramic metal composites are complex, extremely time and energy consuming, environmentally harmful, and rarely able to manufacture articles with complex shapes. Therefore, in order to overcome these disadvantages, self-propagating high-temperature synthesis (SHS) was considered as an alternative method that offers significant improvements over the traditional cermet manufacturing methods [3]. SHS, which is a relatively new and attractive method for producing a wide range of advanced materials, is based on the self-sustaining feature of the highly exothermic reactions of the reactants. The SHS process results in high product purity, since the high temperatures generatedin the reaction cause any impurities to volatilize [4, 5]. SHS has low energy consumption and doesn’t require an external energy source and complex equipment, and it is self-contained [1, 5]. Since combustion synthesis has low power requirements, it is one of the few methods of materials synthesis that is feasible in outer space. Also, the process has a low cost and is capable of directly synthesizing articles with the desired shape, size and structure [5, 6]. The chemical reactions associated with SHS are typically completed in a few seconds leading to the formation of the condensed product. The high reaction rates and relatively rapid cooling in SHS reactions can avoid undesirable grain growth in products which often occurs with the conventional sintering method [3, 5, 7]. The traditional method for sample preparation in the SHS technique is to compact the reactant mixture powders in a steel die by a press to a typical density of about 80% of the theoretical maximum value, before igniting the mixture [8]. This method requires a large compression force to increase the green density and to minimize any pores in the green compact. To overcome these disadvantages, a new method for the preparation of the precursor charge in metal-sulfur by SHS is proposed which can be described as melt casting of a reactive mixture, or reactive casting in short."

Jan 1, 2012

By Arthur Wade

The most important development in connection with the search for oil in Australia during 1940 was on the legislative side. Prior to 1939 legislative enactments in the various states with regard to prospecting for petroleum were such as to prohibit large-scale effort and to bar the major oil companies from operating. The preparation of the Wade Model Bill for the Commonwealth Government in 1939 and the acceptance of the Bill in principle by all States, has gone far to remove these obstacles. Amending Acts, largely based on the Alodel Bill, have now been passed by all States with the exception of New South Wales and Tasmania. In New South Wales an Amending Bill is being drafted, while the Govern-ment of Tasmania is preparing to introduce an Amending Bill provided there is any demand for it. Noteworthy developments followed immediately on the passing of these Amending Acts. The Shell Company (1)1 and the Superior Oil Company of California (2) too$ up large areas in Queensland and com-menced work during 1940. Caltex acquired a big tract of country in the Kimberley district of Western Australia (3) and has made application for an area in the Territory of Papua. An Australian company, The Phoenix Oil Extraction Co., has obtained a permit to prospect over an extensive area bordering the south coast of Western Australia (4). Other developments are foreshadowed. The Shell Company is making an intensive examination of its area in Queensland (I). Geological, geophysical and aerial surveys are in progress. Caltex has three geological parties in the held in Western Australia while Superior Oil Company of California has done some geological work in the interior of Queensland (2). None of these concerns envisages a drilling campaign in the near future. Much exploratory work is necessary. Further work has been done by the companies that were already operating in 1939, though an important Australian company - Oil Search—has abandoned the work of prospecting in Australia. This company has subleased its holdings, at North West Cape in Western Australia (;), to Caltex on a royalty basis. The company also maintains its holdings in, and connection with, the Australasian Petroleum Company Proprietary Limited, which is a combination of Standard Oil (New Jersey), Anglo-Iranian and Oil Search. This company is operating in the territories of Papua and New Guinea. Drilling Victoria.—Although a good deal of drilling was done in the LaBes Entrance Tertiary Basin of Victoria (7), no appreciable production of oil was obtained. In order to test the extent and possibilities of the oil-bearing sand in this region, the Commonwealth and State Governments jointly put down six scout boreholes to depths of between 1200 and I500 it. The results were nega tive. A deeper exploratory horehole put down by the Governments at Seacornbe, or 26

Jan 1, 1941

By Arthur Wade

The most important development in connection with the search for oil in Australia during 1940 was on the legislative side. Prior to 1939 legislative enactments in the various states with regard to prospecting for petroleum were such as to prohibit large-scale effort and to bar the major oil companies from operating. The preparation of the Wade Model Bill for the Commonwealth Government in 1939 and the acceptance of the Bill in principle by all States, has gone far to remove these obstacles. Amending Acts, largely based on the Alodel Bill, have now been passed by all States with the exception of New South Wales and Tasmania. In New South Wales an Amending Bill is being drafted, while the Govern-ment of Tasmania is preparing to introduce an Amending Bill provided there is any demand for it. Noteworthy developments followed immediately on the passing of these Amending Acts. The Shell Company (1)1 and the Superior Oil Company of California (2) too$ up large areas in Queensland and com-menced work during 1940. Caltex acquired a big tract of country in the Kimberley district of Western Australia (3) and has made application for an area in the Territory of Papua. An Australian company, The Phoenix Oil Extraction Co., has obtained a permit to prospect over an extensive area bordering the south coast of Western Australia (4). Other developments are foreshadowed. The Shell Company is making an intensive examination of its area in Queensland (I). Geological, geophysical and aerial surveys are in progress. Caltex has three geological parties in the held in Western Australia while Superior Oil Company of California has done some geological work in the interior of Queensland (2). None of these concerns envisages a drilling campaign in the near future. Much exploratory work is necessary. Further work has been done by the companies that were already operating in 1939, though an important Australian company - Oil Search—has abandoned the work of prospecting in Australia. This company has subleased its holdings, at North West Cape in Western Australia (;), to Caltex on a royalty basis. The company also maintains its holdings in, and connection with, the Australasian Petroleum Company Proprietary Limited, which is a combination of Standard Oil (New Jersey), Anglo-Iranian and Oil Search. This company is operating in the territories of Papua and New Guinea. Drilling Victoria.—Although a good deal of drilling was done in the LaBes Entrance Tertiary Basin of Victoria (7), no appreciable production of oil was obtained. In order to test the extent and possibilities of the oil-bearing sand in this region, the Commonwealth and State Governments jointly put down six scout boreholes to depths of between 1200 and I500 it. The results were nega tive. A deeper exploratory horehole put down by the Governments at Seacornbe, or 26

Jan 1, 1941

By Mary Jean Buchanan

The last twenty years have seen the advent of environmental concerns and sustainable development, and the industry has witnessed the rise of Environmental Management Systems and their registration through several international standardization systems such as EMAS and ISO 14001. Beyond EMS and ISO 14001, which new goal the mining industry should aim at. Life-cycle assessment (LCA), another tool from the Environmental Management System series, is also on the rise and currently the object of an international standard (ISO 14040:1997). Through LCA, it is possible to assess the environmental aspects and potential impacts associated with products and services, taking into account all the activities required for its fabrication, its use, its transportation and its disposal. How could LCA be applied to the mining industry ? Is the international market pressurizing on mining companies to supply an ?environmental ore?? What about the automobile industry and its use of LCA ? Will it influence the ferrous and non-ferrous metal industry, suppliers of raw materials ? This paper presents a review of possible applications of LCA for the mining industry as well as world trends.

May 1, 2001

By Tom Szaraz

Part of a major sewer expansion for the City of Columbus, Ohio. The Big Walnut Outfall Augmentation Sewer?Part II (BWOAS) consists of 13,200 feet of tunnel of 12-foot tunnel passing mainly through glacial deposits with a water head of up to 2 bar. A Lovat RME167SE was used to drive this tunnel with steel fiber reinforced precast segmental liner used for support. This paper will discuss the concepts for tunnel sup-port and TBM selection, the problems encountered with the TBM sealing systems and the solutions used to repair the machine.

By S. M. Geerts, M. T. Wild

In this paper the performance effects of various shaped charge liner designs will be discussed. Several different charges will be tested and the liner design will be reviewed based on the performance in testing. The first type of shaped charge to be tested is a conical charge with dual confinement. For the purpose of this paper, dual confinement is a shaped charge with two liners but containing one explosive charge. Several charges with different dual confinement designs will be tested. Variations in configuration include charges with similar angle and similar diameter. The second type is a double conical shaped charge configuration. A double shaped charge will be considered to be two complete charges formed into a single cone. The goal of the project is to determine if any of the designs increase the efficiency and/or effectiveness of the shaped charge in comparison to the standard conical shaped charge. A standard conical charge will be detonated against a witness plate to get a standard depth of penetration or a baseline. All charges will have a seven cone diameter standoff, allowing the data to be compared to the control charge. Computer modeling will be used to predict the results of the testing that will be conducted. The actual results will be compared to the computer simulation for validation.

Jan 1, 2010