Search Documents

By J. Tomlinson

Shuttle car trailing cable splices were tested for resistance to failure upon being subjected to repeated bending, abrasion, and tensile shocks using a new testing method that closely simulates shuttle car induced stress. The results show that under normal stresses, splices can be made to withstand the equivalent of three months of operational use. Restoring the tensile strength to the conductors is found to be as critical as restoring flexibility. Splices in which the conductors are of slightly unequal length did not present as serious a workmanship problem as previously thought since test results show that the conductors tend to equalize when longer cables, in contrast to short cables employed in previous testing methods, were used. Dynamic recordings of cable tensile stresses are presented for a shuttle car and the new simulated testing method. Two simple but effective methods for removing insulation using a knife and a pair of pliers are described. None of the designs tested for a sacrificial splice covering were satisfactory.

Jan 1, 1979

By A. E. Fiorato

A test program was conducted to evaluate use of high-strength concrete in drilled shafts (caissons). The objective of the program was to determine if internal temperatures developed during cement hydration, or other characteristics of high-strength mixes, affect in-situ strength and stiffness. This paper covers strength results. Two 10-ft (3.0-m) diameter by 40-ft (12.2-m) deep caissons were constructed using two different commercially available high-strength concretes, a "low-heat" and a "high-strength" mix. Measured 6x12-in. (150x300mm) moist cured cylinder strengths at 56 days were 13,690 psi (94 MPa) for the "low-heat" mix and 17,130 psi (118 MPa) for the "high-strength" mix. Compressive strengths and moduli of elasticity of cores taken from the caissons were compared to those of companion cylinders made during casting of the caissons and stored in a moist room. Strengths of 4x8-in. (100x200 mm) cores taken at four ages and tested between 34 and 398 days averaged 81% of strengths of 6x12-in. (150x300 mm) moist cured cylinders at corresponding ages. In-situ (core) strengths of the caissons did not appear to be measurably affected by temperature. However, the data indicate that core strengths were sensitive to level of consolidation, as reflected in entrapped air voids. Overall, the results indicate that high-strength concretes can be used in drilled shaft (caisson) foundations.

Jan 1, 1991

By Edward M. Kawenski

Tests were made in the Bureau of Mines Experimental Coal Mine on stop-pings similar to those used in operating coal mines to obtain information on air leakage through the face and the rupture strength of a stopping subjected to a pressure differential. Block stoppings were made from cinder, slag, and gravel aggregates with and without mortared joints and coatings. Sheet stop-pings were uncoated brattice cloth and nylon or brattice cloth and expanded metal-lath coated with asphalt, latex, mortar, or rigid urethane foam. Limited data were obtained on air through stoppings subjected to simulated roof convergence and to shock forces created by the firing of an adjacent charge of explosive. The pressure differential required to rupture stoppings was determined. shows that coating the face of a stopping effectively reduces ail: leakage. Block stoppings, particularly those with mortared joints, are most resistant to pressure and shock forces than are sheet stop-pings. Where ground movement is a factor, sheet stoppings leak less air than block stoppings.

Jan 1, 1965

By Göksel Hızlı, Selim Ertürk, Ayşegül Bilen, Raşit Sezer, Cüneyt Arslan

The carbothermic reduction of celestite is the first step in producing many strontium products. The way materials move in the rotary kiln has an essential effect on the carbothermic reduction efficiency as well as the temperature. In this study, the reduction of celestite ore and excess carbon blend in a laboratory-scale rotary kiln was investigated. In the experiments carried out at three different temperatures, the rotational speed and slope of the furnace tube were altered, and their effects on the reaction efficiency were examined. The leachability of the reduced powders and the content of the unburned coke indicated the optimal parameters for the reaction.When the speed was increased to 10 rpm, the powders weremoremobile in the stack and could react more easily with the furnace atmosphere. According to the results, celestite can be reduced by carbon at temperatures of 1000–1200 °C, at rates of between 5% and 75%. The maximumreaction yield (75%) was obtained with a slope of 2° and a rotational speed of 6 rpm at 1100 °C.

May 7, 2020

By F. A. Forward, A. H. Ross, J. Halpern

Application of the carbonate leaching process to carno-tite ores has often been limited by the difficulty of obtaining simultaneous high recoveries of uranium and vanadium. The chemical aspects of this problem are discussed and the effect of prior roasting procedures on this discovery is described. IN treating carnotite ores by carbonate leaching it is often necessary to subject the ore to a prior roast. Among the advantages that may result from roasting are: 1) improvement in settling and filtering characteristics of the ore; 2) destruction of carbonaceous impurities that would otherwise contaminate the leach solution and consume carbonate reagent; and 3) substantial increase in extraction of vanadium, which is usually low when the un-roasted ore is leached. Recovery of vanadium may be an important factor in processing carnotite ores, and the fact that vanadium is usually recovered in good yield by acid leaching has often been an economic advantage over results obtained with carbonate leaching. It has been found that response of an ore to carbonate leaching, following roasting, depends primarily on its composition and on the conditions of the prior roast treatment, particularly with regard to the roasting temperature, the atmosphere maintained above the charge during roasting and cooling, and the presence of certain reagents. These factors, especially the last, virtually determine the extractions of uranium and vanadium attainable by carbonate leaching, as well as the reagent consumption on leaching, whereas adjustment of the leaching conditions has only a limited influence. These variables were examined systematically to elucidate roasting and carbonate leaching of carnotite ores and to establish a treatment yielding high recoveries of both uranium and vanadium. Tests were conducted on samples of four different Colorado Plateau ores, described in Table I. Roasting Procedure: The roasting tests were conducted in an electrically heated furnace in which the temperature was controlled to ±15°C. The ore (usually a 500-g charge) was ground to —100 mesh, mixed with the desired reagent, and spread in a silica tray to a bed depth of about 1/2 in. During the roast the charge was rabbled at intervals of 15 min. To provide free access of air the furnace was usually ventilated; however, in a few experiments a controlled atmosphere such as carbon dioxide or hydrogen was maintained above the charge. Leaching Procedure: The pulp, generally comprising 500 g of ore and a 2000-cc solution containing 80 g per liter of Na2CO8 and 20 g per liter of NaHCO3, was agitated in an autoclave at 120°C, under 30 psi 02. Samples were withdrawn periodically, and the solution and ore residue were analyzed. Under the conditions employed, maximum attainable extractions were generally achieved in 4

Jan 1, 1959

By P. Massacci

The modelling of phenomena by nonlinear dynamic Systems Theory representations require the specification and identification of suitable models of the phenomenon and the availability of good optimization algorithms to determine the optimal controls. Stochastic disturbances and difficulties of monitoring the process lead invariably, otherwise, to suboptimal performance. It will be shown that an algorithm can be formulated which will simultaneously identify and optimize such a system. The properties of the algorithm will be derived and its convergence to an optimal control proved. Some results of actual applications will be presented and it will be shown how this approach generalizes easily to optimal control of the actual processing system. These results generalize those of optimal learning and input conditioning.

Jan 1, 1991

By M. K. Larson, J. K. Whyatt

Proper employment of numerical stress analysis design tools is based on the demonstrated ability of a model to capture key elements of the geologic site model and accurately simulate how these elements interact with a mine design. While these tools have progressed markedly, they are, at heart, a gross simplification of the abundant complexity of a natural setting and its response to mining. A generic deep longwall site model was developed that includes aspects of the geology of deep coal mines in the Wasatch Plateau and Book Cliffs coal fields of Utah. The site model contains a set of common features and observations of how these features typically respond to mining. This site model was the basis for evaluating use of empirical, boundary element and volume element stress analysis tools to analyze the distribution of stress around a deep longwall panel. More specifically, this evaluation examined shifting of stress to panel abutments and gob, distribution of stress in the abutment and deformation and failure of bridging strata. Measurements of abutment stress changes at two sites in the Wasatch Plateau region were used to illustrate model calibration. Overall, these comparisons highlight the considerable differences between methods. Volume element tools can incorporate considerable detail and have fewer underlying assumptions, but this detail carries a considerable computational cost. Boundary element tools are much more efficient. However, this efficiency comes at the cost of added assumptions. These assumptions were challenged by the presence of a strong sandstone unit in the overburden, leading to boundary element results that depart significantly from volume element results. Empirical rules are the simplest, but are even more burdened by assumptions, many of which are implicit in underlying cases. Insight into the nature and impact of underlying assumptions in each method is essential to the proper use of results in mine design.

Jan 1, 2009

By E. D. Wilson

A study of factors related to subsidence was specified in a project proposal entitled "Structural Analysis of Block-Caving Operation, San Manuel Copper Mine, Pinal County, Ariz.," approved by the Bureau of Mines early in 1953. This proposal was designed by Charles H. Johnson, then chief of the Base Metals Branch of the Minerals Division, Washington, D. C., assisted by Dr. Leonard Obert, chief of the Applied Physics Branch, Region VIII (now Region V), College Park, Md., and E. D. Gardner, chief mining engineer, Bureau of Mines, Washington, D. C. It read as follows: This project is a study of the mechanics of undercut block caving in a deep ore deposit. The San Manuel is a low-grade disseminated copper deposit containing nearly a half billion tons of ore lying at depths of 500 to 2,000 feet. Development is just starting. Production is to begin in 3 to 4 years (in 1956) at a rate of 30,000 tons of ore a day, or 60,000 tons of copper a year. A Government loan of $90,000,000 /subsequently increased to $94,000,000/ and a long-term Government purchase contract support the capital investment, which will total about $110,000,000.

Jan 1, 1957

By COREY C. BRAYTON

OUR first air travel began at Barranquilla on a trip to the platinum dredging-operations at Andagoya. The fare is based on a minimum weight of passenger, and I will have to admit that the minimum is too low. To make this trip by boat would have necessitated going back to the Canal, thence down to Buena Ventura, and up the San Juan river, which would have taken, counting delays, two or three weeks. The time by Scadta airplane was six hours. We stopped at Cartagena for a day to look over that historic city. The route from there lay along the north coast to the mouth of the Atrato river, then up this river, over the jungle, and over a divide some 300'ft. in elevation and down the San Juan river a few miles to Andagoya at the junction of the Condoto. The General

Jan 1, 1930

By R. V. Ramani

"In a 1985 seminar, we were told that over-optimism abounds in Artificial Intelligence (AI), that AI is neither a science nor a technology yet, and that we will be both exhilarated and disappointed with AI. In fact, even today, there is no single accepted definition of AI; however, certain features have been identified by AI researchers as essential to consider an entity (e.g. machine or program) to be intelligent. According .to Shank (1987), these features include communication (to be able to communicate with), internal knowledge (knowledge about itself), world knowledge (awareness and knowledge about the world outside), intentionality (knowing what one wants and a plan to seek it, ie. goal seeking behavior), and creativity (being adaptable to changing conditions). None of these figures would individually define intelligence; however, each would be a part of intelligence in its own way.The prospects for the development of entities with AI have never been as good as they are now. The combination of advancements in computer hardware and .software along with new insights into the ways in· which we store knowledge and use it for problem solving has enhanced the potential for the creation ~f intelligent entities. After some unbounded optimism of a major breakthrough in the fifties and frustrating disappointments in the two following decades, it appears now that AI has emerged from research labs to industrial practice. This is confirmed by the growing number of repeat applications of AI in business and industry to the extent that AI can now be considered a technology.AI applications are categorized into several distinct areas such as Natural Language Processing, Speech Recognition and Synthesis, Expert Systems, Robotics, Machine Vision, etc. Of these practical realizations, Expert Systems (ES) has the greatest potential for meeting the decision-making needs of the manager in the ever-growing complex scoio-technical systems. Prof. Feigenbaum, an expert and leader on expert systems, has defined Expert System as"" ... an intelligent computer program that uses knowledge and inference procedures to solve problems that are difficult enough to require significant human expertise for their solution. Knowledge necessary to perform at such a level, plus the inference procedures used, can be thought of as a model of the expertise of the best practitioners of the field."""

Jan 1, 1989

By Sylvain Létourneau

Help organizations maximize the benefits of the data that they collect ? perform scientific research in: machine learning, data mining, statistics, artificial intelligence, soft computing, information retrieval, information systems, and natural language processing ? preferred application areas: Equipment Health Management, Bioinformatics, Health, Web Mining ? today?s talk limited to Equipment Health Management While the aircraft is still in the air, IDS: ? clusters relevant WRN, FLR, and snag (pilot) messages ? identifies probable causes based on TSM and provide links to corresponding TSM pages ? assesses MEL conditions (GO, NOGO, GOIF, ?) ? displays relevant maintenance history, suggests fixes based on similar cases ? Commercialization with MxI Technologies Ltd and Air Canada in 2000

May 1, 2008

By Robert Steinitz

SOFT iron parts for magnetic applications, particularly pole shoes, constitute a major portion of the ferrous products of powder metallurgy. The residual pores in pressed and sintered parts reduce values such as the magnetic permeability but service experience extended over a number [ ] of years has proven beyond doubt that in many instances the lower density of powder parts is not prohibitive to their use m replacement of machined magnetic parts The. magnetic requirements for pole shoes particularly the permeability, vary within wide limits, especially with the relative size of the air gap in the finished assembly. The overall permeability of an assembly, µ, is given by the formula [ ] where µm is the permeability of the core material, l the total length of the magnetic path, and a the length of the air gap. Fig 1 shows the variation of the overall permeability with the permeability of the core material, calculated according to Eq I for an air gap of 1 pct of the total length of the magnetic circuit. It is readily recognized that to use core materials hav-

Jan 1, 1948

The Mine Safety and Health Administration (MSHA) conducted a respirable dust survey to evaluate the effectiveness of a water curtain utilized for dust control on continuous miner sections. The purpose of this survey was to determine if the water curtain was effective in reducing respirable dust concentrations, since several mines currently use water curtains to control miners? respirable dust exposures. The survey was conducted on a supersection of an underground coal mine, which utilized two continuous miners on the same split of air. Each continuous miner alternated taking a cut so that both continuous miners would not operate at the same time. The underground coal mine is located in Knox County, Indiana. The water curtain evaluated in this survey was located in the last open crosscut between the intake side continuous miner and the return side continuous miner. When the intake side continuous miner cuts coal, its exhaust air would be used to ventilate the return side of the section. The intent of the water curtain was to reduce the intake air respirable dust concentration (generated by the intake side continuous miner) before the air stream ventilated the return side of the section. To determine the effectiveness of the water curtain in reducing respirable dust concentrations, respirable dust sampling pumps were placed on both the intake side and the return side of the water curtain. Additional respirable dust sampling pumps were placed farther downstream from the water curtain to monitor dust levels downstream of the water curtain, but in an area where respirable dust would not be created by anything other than the intake side continuous miner or additional section air. The water curtain and the respirable dust sampling pumps were operated only when the intake side continuous miner was cutting coal. The samples were analyzed for respirable dust and quartz content. The water curtain showed minimal effect in controlling respirable dust and respirable quartz dust, but the reduction was so negligible that this survey could not quantify the reduction. The measured reductions are within the accuracy of the sampling equipment.

Jan 1, 2009

By A. S. Richardson

THE recent installation of a high-pressure propeller type fan at the Moose shaft of the Anaconda Copper Mining Co. at Butte, Mont., is of interest on account of novelty of design and also because an appreciable saving was made over the cost of a reversible centrifugal fan such as is ordinarily used where a high pressure is required. The lower cost is due solely to the fact that by means of controls on the power supplied to the three-phase, alternating-current, induction motor, directly connected to the propeller it is possible to reverse the direction of rotation of the propeller and thus reverse the direction of air flow. The extra air ducts and reversing doors required for this purpose with centrifugal fans are not necessary, and their elimination greatly reduces these construction charges, which form a great part of the total expense. The Badger State mine for which the Moose shaft is used as the main outlet air course is now being developed to the 4100-ft. level. The old centrifugal fan, formerly used at the collar of the shaft, was installed 15 years ago at a time when most of the stoping was being done above the 2400-ft. level, and when the temperature of the rock was much lower than it is now on the bottom levels recently opened. The old fan, therefore, became inadequate to maintain desirable ventilation conditions, on account of the increase in resistance to air flow incident to the greater depth of the mine workings and because a much larger volume of air is required to offset the higher rock temperatures. Propeller, or disk, fans commonly used in the ventilation of mines are not suited to high-pressure work, but economies in the cost of their installation have long been recognized. In South Africa use has been made of a number of propellers placed in series along a common shaft, the number of propellers used being varied with requirements for meeting different conditions of mine resistance, but the mechanical efficiency is described as being low. In Butte, experimental work was done by the writer along similar lines under somewhat different conditions, but with poor results as to both pressure capacity and mechanical efficiency. Tests were also made of two different types of propeller fans of moderate size, which were said by the manufacturers to be suited to high-pressure mine ventilation.

Jan 1, 1932

By Pekka Taskine

In the Kokkola zinc smelter, as in most other zinc roasting plants, there is now a trend towards using concentrates with an increasing impurity content. This also often means that the size distribution of the concentrates gets finer. Iron is present in sulfidic zinc concentrates with the highest percentage as a single impurity. The behavior of iron in zinc roasting was studied in laboratory experiments. Commercial zinc concentrates with a low and high (1.5 - 16 wt-%) iron content as pyrite or in the sphalerite lattice were oxidized to various degrees to establish the reaction mechanisms of iron in roasting. Microscopy studies were carried out on the calcine, and the findings were presented in numerous photographs of the polished cross sections. SEM/EDS techniques were used for analyzing the phases and particle morphologies present in the samples. An oxidation mechanism of zinc concentrates with a high iron content was suggested.

Jan 1, 2002

By William P. Blake

THE use of diamonds upon a large scale in drilling rocks, and the substitution to a certain degree of rotary diamond drills for the ordinary steel percussion drills, marks a new era in the art of mining. Since the invention by Leschot of the diamond drill, it has steadily advanced in its utility and range of application, and in the appreciation of miners and engineers. I t must be claimed as one of the many gifts of science to the arts ; and it is, in particular, one of the fruits of the scientific education given at the Ecole Centrale, at Paris. Members are all, doubtless, more or less familiar with the construction of the drill and of the machinery by which it is applied in boring. I t is, therefore, my present purpose only to direct your attention to some recent marked improvements, made by the American Diamond Drill Company, by which the economy and efficiency of the machines have been increased. Form of Bit.-The annular or ring form of the drill-head or bit was, I believe, the earliest; and it is still in use, without essential modification, wherever it is desired to obtain a sample " core" or specimen of the rock traversed. But for mere drilling, regardless ~f the preservation of a test-core, a solid-head bit is preferred, except for very large holes. Until recently, these solid-head bits were made with a pointed cutting face shaped like an obtuse cone. This form was assumed to be the best, being most in accordance with the experience obtained with percussion drills. I t is found, however, that the exact reverse

By M McDonald

KiwiRail has a goal of significantly improving passenger rail services to west Auckland, as part of its DART (Developing Auckland’s Rail Transport) suite of projects. The New Lynn Rail Trench (NLRT) project was a significant component of this work. The NLRT project facilitates essential doubletracking of the Western Auckland line, and provides a new commuter transportation hub within a busy town centre.The 1.5 km stretch of track through the New Lynn town centre has bisected the township for over 80 years. Double-tracking the line provided the opportunity to grade-separate road and rail, which would help to re-connect both sides of the township and enhance public amenity and safety.KiwiRail employed an Early Contractor Involvement (ECI) procurement model engaging a consortium comprising Fletcher Construction, Beca Infrastructure and Synergine to develop a Design and Construct solution.With weak soil conditions and high groundwater levels, a diaphragm wall construction method to form the trench walls was selected as the best solution. Further challenges to construction included working within a narrow rail corridor constrained by buildings along much of the boundary, and a requirement to keep the existing line open for rail services. Detailed construction planning was required to ensure rail and construction safety in a constrained space whilst building the trench walls, propping these walls during excavation, and constructing the base slab in the most efficient way possible.This paper will detail the geotechnical conditions and the additional constraints that made this rail trench a challenging structure to design. It will also describe the fi nal design and construction methodologies that were employed, that allowed very successful completion of the project.Additionally, this paper will review the design and construction lessons applicable to the current Victoria Park Tunnel project, and indeed for all future cut and cover tunnel projects in the Auckland isthmus.

Mar 8, 2011

By Steven Rupprecht

"The South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (the SAMREC Code or the Code) sets out minimum standards, recommendations and guidelines for public reporting of exploration results, mineral resources and mineral reserves in South Africa. The Code is being rewritten and updated, with work on-going since 2013. The revision is being undertaken to ensure the Code remains relevant, incorporates developments within the international mining industry and keeps abreast of technology. Some of the changes and their reasons are discussed. INTRODUCTION The South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves (the SAMREC Code or the Code) sets out minimum standards, recommendations and guidelines for public reporting of Exploration Results, Mineral Resources and Mineral Rreserves in South Africa. The Code is being rewritten and updated, with work on-going since 2013. The proposed 2016 update is not significantly different from previous versions of the Code. The revision is being undertaken to ensure the Code remains relevant, incorporates developments within the international mining industry and keeps abreast of technology. The Code sets out minimum standards, recommendations and guidelines for public reporting. However, reporting may be unclear, ambiguous, selective, obscure, distorted or unintelligible. Part of the purpose of the update is to provide better guidelines to Competent Persons (CPs) to ensure that the material information is being reported and that reporting is transparent in accordance with the guidelines of the Code. The information provided should, as required by the Code, be adequate to inform the “reader/investor or potential investor to make a reasonable and balanced assessment of the significance of the information”. The Committee for Mineral Reserves International Reporting Standards (CRIRSCO) highlights the importance of the reporting Codes, as provided from a quote from their website (www.crirsco.com): The mining industry is a vital contributor to national and global economies. It is a truly international business that depends on the trust and confidence of investors and other stakeholders for its financial and operational well-being. Unlike many other industries, it is based on depleting mineral assets, the knowledge of which is important prior to the commencement of extraction. It is therefore essential that the industry communicates the risks associated with investment effectively and transparently in order to earn the level of trust necessary to underpin its activities."

Jan 1, 2015

By Victor R. Spironello

The Bureau of Mines has studied slags associated with ferrous melting, to evaluate substitutes for the auxiliary flux mineral, fluorspar. A waste material recovered from alumina reduction cells, "used potlining," was tested in an 18-in-ID basic-lined cupola and in a 1/4-ton, pilot-scale, basic oxygen furnace (BOF). One potlining fraction, No. 1 cut, is a carbonaceous (graphitic) material and represents the bulk of the entire cell lining. The other fraction, No. 2 cut, is a refractory backup. These materials contain significant quantities of fluorine and other elements fn various compounds. The potlining fractions were blended in ratios believed representative of available materials. Both lump and pelletized forms provided extremely fluid slag. No adverse effects were found on furnace performance, chemistry or strength of the metals produced, or the environment. Fluorine recovery in the slag and fluorine losses to the scrubber water and solids were about the same as when fluorspar was used. There was apparently no lining loss from the cupola, but there was lining attack in the BOF. Since the fluidizing ability of potlining is due in part to sodium and other elements such as aluminum and silicon, less fluorine is needed in the slags when potlining is used.

Jan 1, 1983

Tapira Mine (Tapira, MG, Brazil) is the largest phosphate ore and concentrate producer in Brazil. The mine is an open pit, which until recently operated with a large equipment fleet and now uses a smaller fleet operated by contractors. The annual production reaches 17 Mt of ore plus 14 Mt of waste at a stripping ratio of 0.82. Defining the geological boundaries and forecasting the annual production can be a difficult task if not performed on a reliable model. The geological model has been totally reviewed as well as the estimation process. Ordinary Kriging has been used to build the new block model with P2O5 and contaminant grades. After estimation, block model validation and classification criteria definition to assess resources and reserves, the result is given by the life-of-mine plan is defined after pit optimisation and design. The Lerchs-Grossmann algorithm implemented in the NPV Scheduler was used to define the long-term production targets based on the main parameters P2O5 and the contaminants that are just important to the beneficiation process.

May 1, 2010