Search Documents

By Osarnu Inoue

In Mitsubishi Continuous Copper Smelting and Converting Process, smelting, slag-matte separation and matte converting are continuously carried out in series in three furnaces connected by launders. As a result of this operational configuration of the furnaces, influence of the change in operating condition in upper stream, such as variation of feeds in the smelting furnace, propagates to down stream with some delay. In order to achieve stabler operation, process control algorithm based on the dynamic characteristics of each furnace would be very effective. In this study, the dynamic process simulation model was developed for the smelting furnace. The model consists of two mathematical modules, i.e. the thermodynamic module and the mixing module. The calculation results using operating data obtained at Naoshima Smelter showed good agreement with the actually observed change in temperature, composition and flow rate of matte and slag at the outlet of the furnace. In addition, operation parameters such as reaction efficiency of oxygen and coal, dead volume of melts were estimated.

Jan 1, 1999

Goethite ore are the third most abundant source of iron. The overwhelming part of these ore is represented by low-grade varieties which cannot be used in iron and steel industry without preliminary beneficiation. Biomass is a renewable solid fuel, which is feasible for the substitution of coke and coal in the manufacturing due to its lower contents of harmful elements and abundant raw material sources. Utilization of biomass in iron ore sintering process as heating agent and reducing agent contributes to energy conservation and emission reduction. The biomass was mixed together with goethite ore for roasting process to investigate the effects of reduction roasting. The results show that the goethite ore is dramatically reduced and magnetized into maghemite by biomass with the biomass dosage less than 20% and the roasting temperature below 650 oC. When the goethite ore roasted with biomass, the magnetization values could be enhanced more than two orders of magnitude, meets the standard of magnetic separation, which could significantly reduce the iron beneficiation cost. Keywords: biomass, goethite, reduction, magnetization, roasting

Sep 1, 2012

By Bruce A. McFarlane

"I WOULD LIKE TO SAY how honoured I am that I have been invited to participate in this panel discussion. I have taken the liberty of narrowing my topic somewhat so that instead of speaking on the Sociology of Professions as a whole I will speak on one aspect of it, that is, on Manpower Problems in the Minerals industry of Canada, with some reference to a new social role for the professionals engaged in this industry. This probably means that I will be encroaching on areas covered or to be covered by other speakers, but I hope that when I do so I will do so from a slightly different vantage point. That is, from a sociological perspective rather than from a historical, industrial, business or professional perspective. I plan to divide my discussion into three areas, namely: (i) problems of ownership and control; (ii) environmental problems; and (iii) manpower and recruitment problems. I do not plan nor am I able to provide clear-cut solutions to the various problems I raise under these three headings. Rather, I hope that my discussion of the problems may form the basis for an extended discussion here and elsewhere. Because of the limitations of time, I will only briefly discuss the first two problem areas noted above – (i) ownership and control and (ii) environmental problems - and I plan to concentrate on the manpower issue."

Jan 1, 1972

By Chris L. Powell, Russell J. Denny.

"The remotely located Cockatoo Island iron ore mine off the Kimberly coast in Western Australia, which has been in operation since 1951, was recently expanded up to 50m below sea-level using staged construction of a rock-filled seawall around the open cut mining operation. The most recent stage of the seawall expansion required a seepage reducing cut-off barrier to be installed through the seawall into underlying seabed sediments. A line of grout holes at 1m centres was proposed to form the seepage barrier, with grouting extending 17m below the top of the seawall. Top hammer drilling techniques were used to penetrate the 12m deep rockfill to seabed level, and permeation grouting carried out within the rockfill to fill voids and stabilise material around grout holes. The local 10m tides meant that tidal washout of fines and grout would be a major risk, and so a combination of cementitious and chemical grout was used to create rapid gel times. Following permeation grouting, holes were re-opened to allow jet grouting to hydraulically mix and grout permeable seabed sediments below the seawall. Using the duplex jet grout system in a single pass to 17m below platform level, the jet grouting was extended upwards into the seawall fill itself to overlap with the earlier permeation grouting. Finally a soil/cement mixed capping trench was installed using slurry trenching techniques with soil/cement/bentonite mixed backfill in order to complete the grout treatment. The approach taken allowed considerable onsite flexibility in technique. An automated slurry batching plant allowed adjustment of mixes to suit the varying subsurface conditions which were encountered during the works.IntroductionLate in 2013 Wagstaff Piling was engaged to install a seepage barrier through a rockfilled seawall built to allow expansion of sub-sea iron ore mining operations on Cockatoo Island off the remote Kimberley coast in the North West of Western Australia. Earlier stages of seawall construction had used a variety of different construction techniques with varied success, and the history of sub-sea mining on the island had been plagued with failures, including failures in the slope of the seawall itself, hanging wall failure underneath and inside the seawall, and footwall failures as the ore was mined leaving the rock face inclined at 55 degrees, parallel to the bedding. The current expansion, known as the Stage 4 expansion, was more tightly constrained by the pit geometry and available materials than previous seawall expansion stages that adopted clay core and sheet pile seepage barrier solutions. In Stage 4, an innovative grout curtain seepage barrier solution was selected to ultimately provide the necessary cut-off to allow access to high grade ore, while protecting the mine from inundation by the sea."

Jan 1, 2016

By J. J. Jakosky, D. H. Zellers

"IntroductionThe Bureau of Mines has been conducting experiments in underground communication during a period of several years, and a brief summary of what has been done is as follows:During 1919-1920, investigations were conducted with the geophone. This instrument was used extensively during the World War for detecting enemy digging and mining operations, by means of the vibrations transmitted through the earth strata.A preliminary investigation using short wave-length (200 to 300 meters) radio equipment carried out jointly with engineers of the Westinghouse Electric & Mfg, Co. during 1922.The step was to investigate ground conduction signaling, (called T.P.S. in Signal Corps parlance)."

Nov 1, 1924

By W Angerer

This paper describes the design of the marine riser structures, including the design measures for sealing and protection from flooding, dewatering and connection to the main tunnels, for the Gold Coast desalination plant in Queensland. The risers connect the intake and discharge tunnels to the ocean. Construction commenced on both in April 2007. The paper describes the key design criteria for the risers, the construction constraints that influenced the design and the design of the main elements of the risers and the connections to the tunnels.

Jan 1, 2008

By S. Kamalpour

It has been observed that the productivity of ferromanganese furnaces, and the stability of metal and slag compositions, vary considerably according to the type of coke used as reductant. However, the desired properties of coke for optimum furnace performance are not well understood. In this investigation, the behaviour of four cokes, which exhibited a wide range of performance in ferromanganese production, was investigated by means of laboratory simulations of reducing conditions in the furnace. The Stationary Charge in Controlled Environment (SCICE) technique was used to simulate the conditions in the furnace shaft. Batches of raw materials, mixed in the same proportions as used in practice, were heated at fixed rates to 900, 1100 and 1300°C then cooled. The mass loss was used as a measure of the degree of reduction. Conditions in the lower part of the furnace were simulated by means of melt-reduction experiments in which lumps of coke were drilled out to form crucibles in which enriched ferromanganese slags were reduced at 1500 and 1550°C then cooled. An examination of the raw materials and the cooled, reacted charges using a variety of analytical and characterization techniques enabled the sequence of reaction and changes in morphology of the raw materials to be followed. This enabled an understanding of the behaviour of the cokes during reduction to be developed, which was then used to explain the observed performance of the cokes in practice. By relating the observed behaviour of the cokes in the laboratory tests to measurable properties of the unreacted cokes and to their observed performance in practice, it was shown that to achieve high productivity and good furnace performance, cokes should be selected to have moderately high reactivity towards CO2 (Boudouard reactivity) relative to conventional iron blast furnace cokes.

Jan 1, 2004

By G. W. Jones

The operation of combustion engines of various types at high altitudes and other combustion processes at reduced pressures have made it desirable to determine limits of flammabilities -under these conditions. Experiments carried out by the Bureau of Mines have shown that although natural gas-air mixtures become more difficult to ignite as the pressure is reduced below atmospheric, with a suitable source of ignition the limits of flammability are as wide at 175 mm mercury absolute as they are at atmospheric pressure.

Jan 1, 1949

By Jorge Munoz Reyes, Guillermo

The new entity, Yacimientos Petroliferos Fiscales Bolivianos, created in 1936 for the development and exploitation of all petroliferous zones of Bolivia, including those formerly belonging to the Standard Oil Co., is doing its utmost to bring about rapid development and by this means to create a new source of revenue for the State. With this in view, Y.P.F.B. has opened a new field in the Samaipata region, on the main road between Cochabamba and Santa Cruz. Installation of machinery has begun for the drilling of several wells on the five anticlines that occur in this region. Work has also begun in the Saipuru field, on the Santa Cruz-Charagua highway, which was discovered by the Standard Oil and temporarily abandoned. In this new field, a topping plant will be installed, to supply gasoline and kerosene to Santa Cruz. Explorations are also being made on the neighboring structures of Saipuru. At the end of 1937, the committee that is to study the region of the Chapare in the northeastern part of Cochabamba, was organized. The structures were studied 10 years ago by Kirtley Mather and other geologists. It is hoped that by March 1938 this camp will begin work, as this zone gives promise of being valuable. Development The capacity of the refinery at Camiri has been enlarged in order that it may supply all the needs of that region. In order that the supply of crude may be adequate, several wells that had been almost abandoned by the Standard Oil are being cleaned out. New wells have been located at this camp following the principal anticlinal structure, and during the first half of the year 1938 several wells will be drilled. The same program is being followed in Sanandita but on a greater scale, as the nearness of this district to the Argentine border, which is the best market for the Bolivian petroleum of the south, allows immediate sale of the petroleum. Possibly a new refinery will be installed at this camp, as the one now in existence is only a rudimentary distillery. At the Bermejo camp, which is farther south, intensive work is being done to bring the wells into production. The Standard Oil produced limited quantities several years ago, but since 1927 the wells of this dis-

Jan 1, 1938

By Ramana G. Reddy, Yuxiang Peng

The long-term corrosion behavior of Haynes 230 (H230) alloy in MgCl2–KCl eutectic salt was evaluated at 1273 K for 500 h in Ni crucible in argon gas. The results showed H230 alloy has good corrosion resistance. In addition, corrosion was noted to occur by depletion of Cr, which was deposited on the Ni crucible. Based on the calculation of Gibbs energy of Ni-Cr alloy and exchange current density of Cr in MgCl2–KCl, the Tafel model was constructed to investigate the corrosion potential and rate. The galvanic corrosion can be explained as the predicted results were in agreement with the experimental data.

Mar 1, 2017

By N J. Potter, N W. Brand, J M. F Clout

The increasing demand for iron ore with low concentrations of trace elements, puts increasing pressure on iron ore producers for high-quality material. Understanding the mineralogy, petrography, chemistry, and mineral association of iron ore deposits is becoming increasingly important to provide iron ore products that meet the ever-increasing standards of steel mills. Limited attention has been paid to documenting new orebodies beyond bulk RC drill chip assays and product specification data. Therefore, limited information is known about the spatial distribution of minor and trace elements at the hand specimen scale, and elemental deportment within different ore and gangue minerals. In this study, samples from high-grade microplaty hematite, supergene-enriched martite-goethite and hematite iron ores are examined for their elemental and mineral associations. These samples contain distinctive minor and trace element distributions, with the mapping of deleterious elements (eg Zn, As, Cu) enabling the deportment and abundance within the ore and gangue minerals to be assessed. Results from this study show a diverse range of minor and trace mineralogy that are present in typical iron ore samples, in abundances below the detection limit of routine XRD scans, that host the deleterious elements, including but not limited to, sphalerite (Zn and S), chalcopyrite (Cu and S), xenotime (P and Y), apatite (P and Ca), cryptomelane (K and Mn), barite (Ba and S), alkaline feldspar (K, Al and Si) zircon (Zr and Si) and chromite (Cr and Al). The presence of these minerals and associated deleterious elements, even at low concentrations, has implications for producers, with the ongoing restrictions and tightening of environmental constraints in shipped iron ore products. By understanding the distribution and location of these elements within the iron ore, steps can be considered to maintain increasingly higher quality iron ore supply around the world.

Nov 8, 2021

By A. Niedbalska

A technique was developed for low pressure diamond synthesis using a specially prepared glassy carbon. The glassy carbon is produced in the form of solid plates by slow carbonization process of phenol formaldehyde resin interrupted at temperatures of 1273° K, 1073° K, and 923° K. The diamond synthesis is performed using cobalt plates as a catalyst-solvent. Synthesis was carried out at applied pressures of 6.0 and 3.8 GPa and a temperature of 1970° K and 2170° K. The products were analyzed by the x-ray powder dyffraction method and by microprobe to identify the diamond crystallites. The samples were taken from the place of contact between the glassy carbon and the cobalt catalyst. They were separated from the charge by a chemical method. Diamonds of the best form and the largest size were obtained at pressures that were much lower than those used in the traditional graphite method of diamond synthesis.

Jan 1, 1989

The richer, shallower sapphire deposits of the New England region of New South Wales which have been traditionally mined by the small miner are almost worked out. Larger mining and exploration companies are replacing the small miner and exploring for the primary source of sapphire or lower grade alluvial deposits.   Although in recent years considerable exploration effort has been directed at locating the primary source, commercial exploitation of sapphire is still restricted to the working of alluvial deposits.   If the Australian industry is to compete against Asian and African producers it must use cost effective exploration, mining) processing and marketing methods.

Jan 1, 1990

By Mark Ward

The Rincon del Tigre (RdT) complex is one of South America’s largest and best-developed mafic-ultramafic layered intrusions. It is set in the SE Bolivian lowlands, about 50 km from the Brazilian border.The BGS (British Geological Survey) and GEOBOL (Servicio Geologico de Bolivia) carried out an initial investigation of the RdT complex from 1976 to 1986. In this sense, the paper point out the geology background of The Rincon del Tigre, economical potential, typical ore secuence in laterite nickle deposit and pega pega erosional surface (Oligocene).

Apr 24, 2001

By A. Felipe Uribe-Henao, Camilo Ballesteros, Luis G. Arboleda-Monsalve, David G. Zapata-Medina

Conventional excavation analysis based on total or effective stress methods can result in inaccurate estimation of ground movements when impervious soil conditions or rapid excavation sequences are not found in the excavation (i.e., assumption of undrained response is not valid). The influence of excavation rate, hydraulic conductivity, and excavation geometry on the fully coupled solid-fluid behavior of a braced excavation in cohesive soils are studied parametrically using PLAXIS2D. The coupled excavation analysis is performed using the Hypoplasticity clay model to reproduce the constitutive behavior of soil and the poro-elasticity Biot’s theory to account for changes in pore water pressure due to deformations in the soil skeleton. Results obtained from the parametric studies indicate that excavation rates to hydraulic conductivity ratios, ER/k, smaller than 0.1 and larger than 104 can be used as limits for drained and undrained analyses, respectively. In practical applications, undrained and partially drained excavation analysis with ER/k larger than 102 resulted in a similar ground deformation. However, smaller ER/k ratios demand fully coupled solid-fluid analysis. An analytical method aimed at predicting excess pore water pressures and determining the required type of analysis associated with soil and excavation conditions, e.g., drained, partially drained, and undrained analysis, is proposed herein to accurately estimate the ground movements induced by the excavation.

By J. B. Umhau

During 1928 the United States consumed 73,270 long tons of virgin or primary tin, which was approximately 7.5 per cent more than the 68,198 long tons con¬sumed in 1927 and equaled 41 per cent of the world's production in 1928 (approximately 178,000 long tons). Consumers' stocks amounted to 9,268 tons on January 1, 1928, and 8,587 long tons on December 31, 1928, a net reduction of 681 tons. In addition to the virgin tin accounted for above, 12,106 long tons of secondary metallic tin were used by manufacturers of tin products in 1928. These figures are the result of an inquiry addressed by the Bureau of Mines to manufacturers to determine the amount of metallic tin used by them; in reply, 1,307 establishments reported consumption in 1928. The distribution of the amount consumed by various uses, as shown in the allowing tabulation based on Bureau of Mines canvasses for 1927 and 1928 in comparison with consumption by uses reported by the War Industries Board for 1917, emphasizes the fact that new uses for tin have been developed in only minor or insignificant amounts. Furthermore, although the studies for recent years show that some older uses have been discontinued, the amounts involved were all small and insignificant. Variation in consumption from year to year parallels the fluctuations in demand for the already well-established tin products. For example, the manufacture of bearing metals and solders for motor cars and trucks required 19,000 tons in 1928 compared to 16,000 tons in 1927; the canning industry continues to require the greater portion of the tin plate and also much solder. Growth in the electrical and the more recently developed industries (aeroplane, refrigerators, radio, etc.), while affecting total consumption of bearing metals, solders, etc., has made little change in the proportions required for these basic methods of using tin.

Jan 1, 1929

By Angelina Anani, Nathalie Risso, Gail Heath, Dean Riley, Nilufer Akbulut, James Werner, Víctor O. Tenorio

Implementing a Digital Twin at the San Xavier Mine Laboratory (Sahuarita, AZ), requires a network redesign with a robust architecture. The goal is to create an ecosystem in where all personnel and equipment can be monitored in real-time from the University of Arizona campus, visualizing the site in a digital terrain model. A wireless mesh will help to test robots with autonomous features. Expected outcomes include data retrieval and analytics, the evolution of communications and safety protocols, tele-operation, and an innovated approach for managing the site with new supervision challenges. A timeline with expected commissioning benchmarks is also included.

Feb 1, 2024

By R. J. Visintainer, W. L. Whitlock

"Difficulties with the sizing and operation of centrifugal froth pumps are common and the underlying fluid dynamics are complex. Design and selection often relies on previous experience, offering unreliable guidance for novel applications or unexpected problems. The current paper describes a program of extensive laboratory testing on froth handling centrifugal pumps, covering a range of flows, heads, speeds, viscosity, air content and froth stability. Variations in impeller vane design and the effectiveness of an airlock venting apparatus were also examined. The program resulted in a better understanding of centrifugal froth pump dynamics and insight for the troubleshooting of field applications.INTRODUCTION The Challenge of Pumping Froth In pumping mineral processing froth, the handling of large quantities of air within the fluid is often unavoidable. Efforts to reduce the amount of air present at the pump suction, while always recommended for improving pump performance, may have limitations. Some strategies may also carry an economic penalty, such as unwanted process dilution (e.g. due to water spray or injection), or increased capital cost of equipment due to oversized pumps, sumps and/or piping. Froth pumping losses fall into several categories, as described below and represented graphically in Figure 1. • Density effects: Entrained air reduces the pressure created by the centrifugal pump in direct proportion to the reduction in bulk density. This is not a true “loss”, since the head produced by the pump (in meters of froth), may remain unaffected. However, the reduction in pressure often leads to a corresponding increase in pump speed required to drive the system, which itself leads to increased NPSH required by the pump (NPSHR). Furthermore, by adding a gas phase, the overall volumetric flowrate is increased, assuming a fixed quantity of de-aerated liquid being handled. This leads to increased suction velocity which further reduces the NPSH margin by simultaneously increasing pump NPSHR and decreasing system NPSH available at the pump suction (NPSHA). • Viscosity effects: Increased viscosity introduces an additional factor in some froth pumping applications, such as oil sands bitumen froth. Losses result from increased shear stress within the fluid flow, which increase with flowrate. Viscosity also facilitates the formation of airlock by reducing turbulence and allowing individual bubbles to coalesce more easily within the flow stream. Finally, it increases pump NPSHR by increasing local pressure drop in the vicinity of the vane inlet edges. • Airlock effects: Also known as air binding, it occurs when air or gas coalesces within the pump suction or impeller passages and begins to collect there, held by buoyancy forces within the rotating flow field. In essence, the liquid “floats upwards” towards the pump suction against the outward directed centrifugal forces. The airlock acts as a blockage, with corresponding reductions in flow, head and efficiency. NPSHR also increases, due to increased velocity and distorted streamlines in the flow circumventing the blockage."

Jan 1, 2012

By Yunhua Gan, Xiaowen Chen, Yang Tong

Experimental studies of electro-spraying were carried out using ethanol as fuel in a microcombustor under combined electric field. And the effects of different electro-spraying modes on the combustion efficiency were analyzed. Results showed that when ring electrode potential was invariant, there were four different electro-spraying modes with the variations of nozzle potentials, which were varying with the flow of ethanol. The cone-jet mode was the stablest one during the whole experimental process. The atomized ethanol was ignited and combusted stably near the steel mesh, the combustion efficiency increased firstly and then decreased along with the increasing of the equivalent ratios, reached the maximum values when the equivalent ratio equal to 1.0. And the maximum values were the highest at the cone-jet mode, and the lowest at the pulsed-jet mode.

Jan 1, 2016

By Brian Wilson, John Scholte, Megan Atkinson

"In November 2004, the residents of the City of Nanaimo, B.C., Canada voted to approve a new conference centre as the centrepiece of a proposed revitalization project for the city’s historic downtown core. The proposal goal was to replace a cluster of derelict buildings with a dynamic and modern complex that would connect existing city facilities to a new conference facility, the Vancouver Island Conference Centre (VICC). The conference centre is expected to create 150 full-time jobs, attract visitors/ delegates from across North America and generate new economic opportunities for local businesses.However, the proposed site posed a number of geotechnical and geoenvironmental challenges. As is often the case with coastal cities, historic growth of the Nanaimo downtown and harbour area was achieved through reclamation of former waterfront areas and inlets. These areas were often infilled with random fills and even wastes, leaving a legacy of variable density heterogeneous fills contaminated with a variety of pollutants. Preliminary assessment of the site indicated a high likelihood of a requirement for deep foundations, a high risk of liquefaction in the event of an earthquake and the presence of both soil and groundwater contamination. Construction would be further complicated by the requirement for two levels of basement parking and the proximity of adjacent buildings and major roadways to the work area.With a limited budget (fixed by the referendum) and timeframe, the city needed a cost-effective solution to proceed with construction. A number of options were considered, but an innovative design using leading-edge Cutter Soil Mixer (CSM) technology best met the geotechnical and budgetary requirements of the site. The CSM approach also addressed the environmental concerns of contaminated soils and groundwater. Golder Associates Innovative Applications (GAIA) Inc., in association with the designers of their parent company Golder Associates Ltd. (Golder), proposed the CSM technology — at the time the first North American application."

Jan 1, 2008