Search Documents

By Z Li, A Fleming, S Webster, L Snyman

Northparkes Mines is developing the E26 Lift 1 North block cave mine, which is adjoined to the existing E26 cave. This paper presents the challenges and methods used to design the ground support system during the feasibility study. Calibrated numerical simulations were conducted to forecast the levels of rock mass damage and to assist the ground support design. Generally, low to moderate rock mass damage is forecast on the extraction and undercut levels. However, poor ground conditions are expected in sheared and preconditioned zones adjacent the existing E26 cave. This will result in difficult ground conditions during development, undercutting and drawbell establishment. Empirical assessments were conducted to make sure the ground support system is able to handle both the static and dynamic load demand, and to accommodate the deformation values. A safety factor of 1.5 was used for the designs to cover the unknown rock mass conditions and potential for larger seismic events. Learnings from the E26 Lift 1 and SLC, also mining against the E26 cave, are incorporated into the design. Fibrecrete, mesh and resin bolts / mechanical anchors are the primary ground support system used, and cable bolts for intersections with a span of more than 6 m. Following undercutting and during the operating life of the mine, secondary ground support and rehabilitation will be required.

Mar 15, 2021

By Claude R. Ayoub, Charles A. Kliche, David G. McDowall

Homestake Mining Company's Open Cut Mine is located in Lead, South Dakota, in the northern Black Hills. The mine is within 300 feet of occupied residences on the south end, and within 1200 feet on the north end. Mining began at the north end of the open pit in October, 1983, and blasting related complaints began almost immediately. Noise and ground movement comprised the majority of the structural damage claims. As a result of these complaints, Homestake purchased a recording seismograph and began monitoring nearly every blast. In addition, the company hired a consultant to review Homestake's blasting and monitoring practices. He was also asked to do a single, one-time study of the cracks in six homes. This initial work led to Homestake monitoring all blasts with three seismographs and having South Dakota School of Mines and Technology do a year-long study of crack development and propagation in five homes in Lead.

Jan 1, 1989

By John Petty, John Loviza

Single sentence describing content-- "The best ally an Explosives Engineer can have in a court of law is a regulations enforcer stating all codes and standards were met on a jobsite".

Jan 1, 1996

By Gary Anderson, J. P. Remi Proulx

Rio Tinto’s Colowyo Coal Mine produces 2.1 million tons per year in northwest Colorado. Colowyo uses the terrace mining method to recover up to seven coal seams ranging in thickness from 5 to 20 feet. Coal recovery in the 6 foot thick high grade C-seam has recently been challenged due to large variations in the pitch and roll of the seam. As well, some coal damage was seen due to an increased thickness of the overburden consisting of a hard sandstone channel.

Jan 1, 2012

By Denard Brandt, Isidro Martinez, Greg Baker, Laura Slattery, Teddy French

The Dos Pobres Mine is a copper oxide heap-leach mine located near Safford, Arizona. Mine production is 180,000 tons (163,293 tonnes) per day with a stripping ratio of 2:1. During the startup phase of the mine, the required fragmentation size was easy to achieve as the ore was highly weathered and fractured near the surface. As the mine depth increased, the proper fragmentation size became harder to achieve due to less weathering and different rock types. Because copper recovery increases as crusher product size decreases, achieving the appropriate product size at the crusher is the operating priority.

Jan 1, 2010

By B. D. H. Knights, M. A. W. Bryson

Flotation of PGM ores, specifically UG-2, presents a number of technical challenges. These centre on the prevalence of chromite. Subject to over-grinding, chromite is primarily recovered to the flotation product through entrainment. This is of unique concern as it must be kept below a threshold for downstream smelting, with significant operational and monetary penalties being imposed should it exceed this concentration. A number of strategies have been developed to maximise PGM recovery in the presence of this unwanted contaminant. Specialised flowsheets form a vital basis and advanced control algorithms further enhance PGM recovery while minimising the recovery of chromite. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists of CIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By J. C. Agarwal

A significant portion of the, coal mined by U. S. Steel is beneficiated to upgrade the quality of the resultant coke to meet blast-furnace requirements. Primarily because of degradation from modern mechanized mining methods, a considerable quantity of the coal to be beneficiated is in the 1/4-inch by 100-mesh size range. In the cleaning plants, this coal is usually cleaned on concentrating tables and then mechanically dewatered in solid-bowl centrifuges to 9 to 14 percent water. At some plants, to further decrease the amount of water shipped with coal, and to improve the coking characteristics of the coal at its destination, mechanical dewatering is followed by thermal drying. At U. S. Steel's-Alpheus preparation plant at Gary, West Virginia, approximately 50 percent of the total coal produced is in this fine size range, and two fluidized-bed dryers are used for the thermal drying step. The two fluidized-bed dryers are 14 feet in diameter and were designed by the Dorr-Oliver Company. Although the original design called for a rate of drying equivalent to 37 tons, of moisture per hour, presently they are removing twice that amount. This paper describes, the major problems encountered' in operating these dryers at the present, high capacities and how they were overcome.

Jan 1, 1963

By Roberto Golchi

This article describes the method used to quantify the Environmental Impact for the mining, by drilling and blasting, of a borrow pit for a gravity-dam. The affected environment was broken down into a number of components, such as public health and safety, social relationship, air and water quality, flora and fauna. The effect of the various impacting factors from the mining activities, both directly and indirectly, was then calculated for each environmental component. To do this, each impacting factor was first given a magnitude, a number based solely on the range of scenarios possible for the impacting factor. A matrix of weighting factors was then derived to systematically quantify, and normalise, the effects of each impacting factor on each environmental component. The overall impact upon each individual environmental component was then calculated by summing the weighted magnitudes for all the impacting factors.

Jan 1, 2003

By Jeremy Gregory

The disposal of end-of-life electronics is an issue receiving increasing scrutiny. This paper evaluates several alternatives for recycling cathode ray tubes (CRTs) within monitors and televisions. The primary recycling options for the glass, reuse in new CRTs or as a smelter flux, are examined from economic and environmental standpoints. The economics are modeled using a cost model that includes dependencies on processing costs, transportation logistics, and incoming material composition. The environmental consequences are modeled using life cycle assessment methodologies to determine the energy embodied in each processing alternative. Results map out preferred processing alternatives across a range of technological and operational conditions. The results indicate that economic costs and environmental consequences are heavily impacted by transportation. The preferred destination of CRT glass for a recycler is highly dependent on the proximity of the consumer to the recycler, although it is generally economically advantageous for the recycler to extensively dismantle the CRTs.

Jan 1, 2006

By A. D. Garman

This paper presents one of a series of digests of foreign mining leg- islation and court decisions which is being repared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countrics. This interpretation of the laws of Panama has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to who it is being referr ed through the courtesy of the Department of State.

Apr 1, 1930

By H. V. S. Tingley

My topic today is future trends in compensation for the mining industry. I seldom get the chance to speak about a subject of such immediate interest to an audience, so I would like to make the most of this opportunity by telling you that everybody in this room will become rich beyond his wildest dreams in the next few years. I would like to open my talk that way, but in compensation, like everything else, there is a great gap between dreams and reality. Back to reality. When we talk about compensation, we?d better define our terms because the compensation is really an umbrella for five basic types of payment made to management personnel. Slide 1 identifies these elements of compensation.

Jan 1, 1980

By John B. Squyres

The purpose of this paper is to describe certain features of the uranium deposits of the South San Juan Basin, and to suggest a mode of origin for the deposits which is consistent with the data. A series of photographs is included at the end of the paper to illustrate the nature of the ore bodies. Since the general geology of the Grants Region is well described in the literature, it will be only briefly reviewed, and the time will be spent instead on the morphology, spatial relations, and geochemistry of the ore deposits. Part of this material is original, but data and ideas have been taken from a variety of sources, including the literature and the personnel of the USGS, the AEC, and many of the operating companies of the South San Juan Basin. I gratefully acknowledge these sources. The accuracy of the data and the conclusions presented here are my own responsibility, however.

Jan 1, 1974

By Orlando C. Gaspar

The textures of the ores, the fine mineral intergrowths, the complex distribution of the deleterious minor elements, and the low base metal contents in some ore types, pose many technological problems to the beneficiation of the volcanogenic massive sulphides occurring in the Iberian Pyrite Belt. In particular fine intergrowths of the base metal sulphides with pyrite impose extremely fine liberation sizes (Kao=15 to 25um). The mineralogical, textural and metallogenic studies have provided an understanding of the distribution of vertical and lateral metal zoning in the ore bodies. Mapping of the ore types, carried out by mine geologists, and the metal zoning patterns computed from data base have shown that ore types are distributed as ore lenses, and that vertical and lateral base metal zoning exists in several orebodies. Since ore processing efficiency is affected by ore textures, and because the same mineral often shows different textural features, a relationship between the textures of the feed ores and those of the middlings must be established for all ore types defined at the deposit scale. For supplying, on time, the information needed for the optimization of the concentration processes, empirical methods of determining the mineralogical and textural characteristics of the several ore types have been developed.

Jan 1, 1995

By T. H. Ramsey, Richard Shield

A process has been developed for fabricating thin-film resistors that are compatible with integrated circuits. Films are produced by evaporation of single refractory metals using an electron beam heating source. Resistor paths are then made using standard photoresist etching techniques. A low-temperature coefficient of resistance is obtained by control of nucleation during deposition of the film. One application of the process has been the development of a discrete resistor used for current setting in linear integrated circuits. Multiple thin-film resistors were formed on oxidized silicon substrates using molybdenum metal as a source. An evaporated protective layer of SiO2 over the resistor prevents resistance changes which might occur during subsequent high-temperature processing. Properties of a typical resistor are as follows: R = 15.7 ohm per sq, tolerance surface dimensions = 0.028 by 0.028 in., stable after 4000 hr at 0. 75 w without heat sink. THIN-FILM resistors have been investigated for many years with a large selection of usable resistors resulting from a wide variety of materials. Many of the processes necessitate a high degree of complexity but in nearly all cases the conclusions have been that the materials used in each case were acceptable provided the deposition process was reproducible and could be controlled sufficiently to give the required tolerances. It is our opinion that simplicity is still the key to thin-film resistor fabrication. In this regard, the single metal is obviously the simplest process to control, provided all the necessary properties can be obtained. The idea is not original in this laboratory by any means. Others have taken this approach.' It has been demonstrated that a fairly wide range of resistivities can be obtained by careful control of deposition parameters for any given metal, and by selection of several single metals a very broad range of stable resistors can be obtained. The transition from one metal to the next is made when a film becomes too thin for adequate process control or long-term stability. A great deal of emphasis is once again being placed on the thin-film resistor. Although they have been thoroughly studied in the past, new applications have been found that require the properties obtainable only from thin-film resistors. Integrated circuits, in general, are advancing toward higher speeds and radiation environments which require replacement of the present diffused resistors. Linear circuits in particular are requiring high-power, high-precision resistors for the more advanced applications. The particular requirements of some linear circuits are such that a discrete resistor is required. The resistor described in this paper was developed as a 15.7-ohm precision discrete resistor for use in a current regulating circuit requiring a +2 pct end of life overall tolerance, a dissipation of 750 mw, and the ability to operate over a fairly broad temperature range (i.e., a low temperature coefficient of resistance, TCR). State-of-the-art integrated circuit and silicon processing technology lends itself well to the fabrication of thin-film resistors. Not only is the resistor thin film well-suited to integration on individual circuits, but the oxidized silicon surface provides one of

Jan 1, 1969

By Fred D. DeVaney

MINNESOTA taconites are extremely hard, and fine grinding is required to produce an acceptable concentrate. To reduce grinding costs, waste material is rejected by magnetic separators as soon as it is liberated. Cyclones are now used in all Minnesota taconite plants to close the grinding circuits. Erie Mining Co. installed its first grinding section at Aurora, Minn., in 1948-a 9 ½ x12-ft. mill and a fine grinding section consisting of a 10 ½ x12-ft ball mill in closed circuit with a duplex 60-in. spiral classifier. Concentrates from the magnetic cobbers treating the rod mill discharge passed directly into the classifier; the ball mill discharge was also treated in magnetic separators and the concentrate from these machines also went to the spiral classifier. Both concentrates passed through ac demagnetizing coils. It is axiomatic that for proper classification the material in suspension must be well dispersed, and it follows that magnetic concentrate must be almost completely depolarized if classification is to be successful.

Jan 8, 1957

By Bohumir Jelinek, Sergio Felicelli, Mohsen Eshraghi

"We present a parallel lattice Boltzmann - cellular automaton model of the two-dimensional dendritic growth during solidification of binary alloys. The model incorporates effects of solute and energy transport under melt convection. The parallel performance of the algorithm is assessed. A loss in the parallel efficiency is observed when multiple computational cores per processor are utilized. Excellent strong scaling up to thousands of computing cores is obtained across the nodes of a computer cluster, along with the near-perfect weak scaling up to forty thousand cores. The presented solidification model shows a good scalability up to centimeter size domains, including millions of dendrites.IntroductionLattice Boltzmann method (LBM) is an attractive numerical technique for solving fluid dynamics problems. Its advantages are simple formulation and locality, with locality facilitating parallel implementation. In the present model, interface kinetic is driven by the difference between local actual and local equilibrium liquid composition [1]. The cellular automaton (CA) technique is deployed to track the solid-liquid interface [2]. A serial version of the present LBM-CA model with a small number of dendrites was validated against theoretical and experimental results in the previous publications [3, 4]. In this work, it is the first time that simulations with millions of dendrites were performed, something not possible with the computationally much more costly phasefield method [5].This research effort examines a technique for simulations of millions of dendrites in centimeter size domains, including thermal, convection, and solute redistribution effects. Nearly ideal scaling properties of the model are demonstrated. This extensively large landmark was achieved because of• the CA technique being two orders of magnitude faster than alternative, phase-field methods [5]• highly parallelizable LBM method, convenient for simulations of flow within complex and time dependent boundaries• availability of the powerful NSF Extreme Science and Engineering Discovery Environment (XSEDE) supercomputing resources"

Jan 1, 2013

By C. J. Allen, L. Battiston

"Introduction It has long been recognized by the hot-dip galvanizing industry that the characteristics of the galvanized coating can be influenced significantly by steel and pro cessing variables. Probably the variable of most concern to galvan izers today is steel chemistry. More specifically, the problem is the excessive reactivity of continuously-cast, silicon-bearing steels. In the past, structural steels processed by general galvanizers were in the low-to-medium ca rbon category and contained silicon at either low impurity levels (as with rimmed steels), or less than approximately 0.10% (as with semi-killed steels). The structures of the coatings produced on such steels are characterized by dense, compact layers of delta and zeta iron-zinc alloy phases and a distinct outer layer of eta zinc, which usually imparts a bright shiny appearance to the coating. The presence of silicon in steel, above the so-called semi-killed levels, is known to cause marked stru ctural changes in galvanized coatings. Such coatings are characterized by a relatively thin delta layer, a thick , coarse zeta layer and frequently an absence of the eta layer. The eta phase, comprising zinc which is carried out of the bath during withdrawal of the work, can be consumed by the continuation of the coating reactions until its temperature drops to the solidification point. This results in a dull grey and often mottled surface instead of the usually bright metallic appearance. These galvanized coatings are usually much thicker than coating specifications requ ire and they are usually more brittle and have poor adhesion to the steel. In service, these coatings tend to develop a rust-like discolouration. With the wider use of continuous casting by the steel producers and the associated additions of silicon in this process, the problem is becoming more important and receiving greater attention from the galvanizing industry ."

Jan 1, 1987

By R. E. Head

[This paper embodies the data obtained by a detailed statistical, microscopic analysis of the composite mill feed concentrate, and tailing from the Magne and Arthur mills of the Utah Conger Co. for 1 month in 1929. It is one of a series of papers by the same authors5 dealing with the mineralogical characteristics of the ore and concentration products from various well-known plants. The work was done in the cooperateive microscopic service laboratory at Salt Lake and represents the results of cooperation between the United States Bureau u of Mines, the Utah Copper Co. and the University of Utah.]

Jan 1, 1935

By R. C. Fernandes, F. L. Santos

Aluminum alloys in particular, have certain limitations when subjected to welding process. This is mainly present because aluminum alloys have high thermal conductivity, high contraction in solidification and high hydrogen solubility. Taking this into account, the FSW process has great potential for this application, since it is autogenous, held without metal melting and without the use of slags or shielding gases. From this concept, the aim of this study is to evaluate the joining of thin sheets of aluminum alloy 3105 H26 with 0.7 mm of thickness. To performing of the tests, some parameters were analyzed, such as: tool penetration in the sheets, attack angle, the type of welding tool and penetration control mode (position or force). The results indicated that the force control mode is most suitable for thin sheets, and the transient state at the beginning of welding was the most critical part to control the welding quality.

Jan 1, 2015

By Miguel N. Herrera, Abbas H. Mirza, Fiona M. Doyle

The standard test methods used to determine the pyrite content of coal and mineral wastes, and their propensity to release acidic drainage, are critically reviewed. In addition to analysis of total sulfur by combustion, test methods using selective oxidation of pyrite by HNO3 and H2O2 are available. The oxidation kinetics of pyrite vary appreciably from sample to sample, and it is difficult to ascertain whether complete dissolution has occurred in heterogeneous materials. The reliability, reproducibility and suitability of different standard test methods were studied, using well characterized ore and coal pyrite samples. The kinetics of pyrite dissolution were also investigated. The results are discussed in terms of the fundamental chemical and physical characteristics of each sample, and the implications for waste characterization are considered.

Jan 1, 1992