Search Documents

By Ricky Chipka, Roshan Thapa, Richard Yovichin, Greg Rogoff, Patrick Niemuth

A 4.5-mile-long, 96-inch-diameter outfall pipeline was constructed between North Texas Municipal Water District’s proposed Sister Grove Regional Water Resource Recovery Facility and the Stiff Creek Discharge Structure. Two TBM-mined tunnel segments were excavated for the outfall pipeline through rock and mixed-face conditions within the Austin Chalk Formation. The TBM mining performance was tracked in detail and evaluated during mining. This paper discusses the TBM configuration, TBM utilization, advance rates, and challenges of both tunnel segments.

Jun 13, 2023

By L. Frost

The establishment of a retreat system of longwall mining in this submarine coal field has been under study for many years and, although in special cases there have been limited local applications of this method of mining, there has been no attempt until quite recently to establish a uniform system of longwall retreating' in this area (see Figure 1) Where retreat walls were established, it was strictly as a result of physical, rather than economic conditions. In some of the operations- of the Corporation, where the coal was liable to spontaneous combustion- or the area subject to bumps as in No. 2 Mine of the Cumberland Railway and Coal Company in Springhills the recovery of the coal on a retreat system was more or less a necessity.

Jan 1, 1964

By R. C. Buehl

[Improvements in refractories for high-temperature service have made possible the use of higher temperature in many processes. Consequently, it sometimes is desirable to use gases heated above 1,600° F., and for moderate rates of gas flow, there gases can be heaters best with pebble heaters. Pebble heaters of the stationary-bed type in which the chanber was lined with mullite brick and pebbles of pure alumina served as the heat-exchange medium have been used recently to heat the air blown into an experimental blast furnace4/ These pebble heaters worked well and made it possible to use air temperature up to 2,500° F. at the tuyere of the furnace. Since little has been published on this type of gas heater, a review of the construction on employed and operating data should assist in selecting applications and designing units.]

Jan 1, 1953

By Gill Montgomery

At this moment in the history of the world, the all- pervading and universally most important fact is that the world population is beginning to outgrow its food supply, and the United States has suddenly lost its ability to give away huge food surplus to any nation in the world with a food shortage problem. This, of course, means that, all of a sudden, our government must completely reverse its former bureaucratic stance regarding crop controls and agricultural price supports, to out-right incentives to increase farm production and bring more idle land into food-growing use.

Jan 2, 1967

By W. E. Kuhn

Introduction The work, of which some of the results are described in this paper, was started with the object of investigating the properties of certain binary alloys of titanium made from powders. Our main interest was in the possible use of such alloys in gas turbines. We were attracted to titanium, as have been others, by its high melting point (I,724° ± 11°C.), its low density (4.54), and the likelihood that, if a relatively wide use could be found for the metal, it might become available in commercial quantities at a fairly reasonable price. The readiness with which the metal reacts with hydrogen, oxygen, and nitrogen was recognized from the very beginning. At the same time there seemed a good chance that alloys could be produced which, because of the formation of protective films, would resist the attack of these and other corrosive agents. No specifications were drafted to cover the 'quality' of the titanium hydride powder which was used in our work and which was, to judge by the results of a few preliminary experiments, the most useful source of titanium then (1944) available in sufficient amount for our purpose. During the course of our work, the need for such specifications became very clear (see Sections 9 to 12 of this pa per). Even today, lack of knowledge regarding the effects on titanium of impurities, some of which may later be looked upon as essential elements in commercial alloys of titanium, and difficulties in manufacture, make the preparation of specifications for commercial titanium and titanium compounds a doubtful procedure. The papers presented at the 1948 Symposium on Titanium, sponsored by the U.S. Office of Naval Research lend colour to this view. At the time our work was commenced, one had to depend upon the manufacturer to supply what he considered to be his 'best' material. It may be some time before we can ask for more than this, the question as to what is his 'best' being left to the manufacturer to decide. However, in this connection the results of our study may be of some value and on that account we are constrained to publish them.

Jan 1, 1950

By J. A. Organiscak

Longwall mining technological improvements have provided significant increases in productivity over the last 15 years. Longwall productivity is anticipated to continue to escalate with expanded application of automated equipment. Automation technology that will likely be adopted over the next 5 years is memory cut with shearer initiation of shield movement supervised by a couple of face workers. Operations using this technology will most likely relocate many production workers from the face to the outby gate entries and position several face workers outby the shearer, exposing workers to different health and safety risks. These changing risks are primarily related to worker relocation and expected increased production levels. Workers outby the face will most likely have less dust and noise exposure, but will be exposed to other safety hazards associated with outby equipment movement, materials handling, and gate entry ground movements. The face workers will most likely be exposed to higher respirable dust and noise levels generated by the equipment at elevated production rates. Methane gas emission is also expected to increase with faster mining rates. These operational changes and the control technologies needed to reduce redefined longwall worker hazards at semiautonomous longwall operations require examination to maintain the health and safety of mine workers.

Jan 1, 1996

By A. K. Croteau

"At Craigmont Mines Limited, Merritt, B.C., the mining practice of trackless sub-level caving was started in the latter part of 1966. This type of mining was new to the mine personnel and the mining industry of Canada as a whole. Sub-level caving has presented many old and a number of new problems in maintaining the equipment used in this method. This paper will deal with some of these problems as they affect this particular mining operation. It will be impossible to review all phases of the equipment, but an attempt will be made to cover the most pertinent aspects in maintaining the drilling, mucking and hauling, and auxiliary equipment."

Jan 1, 1970

By Peter Zhang, Dan Neilans, Scott Peterson, Scott Wade, Joe Pugh, Ryan Mcgrady

"A coal outburst is a severe safety hazard in room-and-pillar mining under deep cover. It is more likely to occur during pillar retreating. Multi-seam mining dramatically increases the risk of coal outburst within the influence zones created by remnant pillars and gob-solid boundaries. Though coal outburst is generally associated with heavy loading of coal pillars, its occurrence is difficult to predict. Risk management provides a proactive tool to minimize coal outburst in room-and-pillar mining under deep cover. Risk assessment is the first step in identifying and quantifying outburst risk factors. The primary risk factors for coal outburst are overburden depth, roof and floor strength, geological anomalies, mining type, multi-seam mining, and panel width. A risk assessment chart can be used to proactively screen out mining sections with high risk of coal outburst for further analysis. Gob-solid boundaries and remnant pillars are critical factors in evaluation of the coal outburst risk of multi-seam mining. Risk identification, risk assessment, geologic influence mapping, geotechnical evaluation, risk analysis, risk mitigation, and monitoring are essential elements of coal outburst risk management process. Training is an integral part of risk management for risk identification and communication between all the stakeholders including management, technical and safety personnel, and miners.INTRODUCTIONA coal outburst is a sudden violent burst of coal from a pillar with broken coal or blocks of coal forcibly ejected into open entries. A coal outburst is a severe safety hazard as the mining crew is highly exposed at the site when the event occurs. Though deep cover and strong roof and floor are underlying geologic conditions of a potential burst incident, its real occurrence is also the result of additional mining factors. In room-and-pillar mining, a coal outburst could occur during both development and pillar retreating, but the latter greatly increases the risk of outburst. The other risk factors of coal outburst also include mining layout, multi-seam mining, presence of adjacent gob, cutting sequence, and local abnormal geologic conditions. Over the years, the cases of coal outbursts have been studied by many researchers and mining practitioners(Peng, 2008; Newman, 2008; Iannacchione and Tadolini, 2008; Gauna and Phillipson, 2008; Hoelle, 2008; and Newman, 2002). It is commonly believed that the coal outburst is the result of a sudden release of elastic strain energy stored in coal pillars and is highly associated with cutting into heavily loaded coal pillars, but its occurrence is a rare event and is difficult to predict. A number of engineering controls have been recommended to mitigate outburst potential. For room-and-pillar mining, sufficient pillar sizes have been the primary control for coal outburst prevention. The pillar design tools such as ARMPS and AMSS developed by NIOSH have played an important role in the design of stable pillars to prevent pillar collapse and squeezing as well as coal outbursts. In fact, with the implementation of pillar design using proper stability factors, pillar collapse and squeezing have been almost eliminated, and the number of coal outbursts has been greatly reduced in the US over the past decade. However, after a few outbursts occurred during pillar retreating in the US over the past a few years (MSHA, 1996; MSHA, 2014; MSHA, 2013), it has been realized that sufficient pillar size is still not enough to prevent coal outbursts. The investigations of the incidents showed that other factors such as multi-seam mining, panel layout, cutting sequence, and local geologic factors also seemed critical in causing the events. Therefore, it has become imperative that additional proactive measures beyond proper pillar design be implemented to prevent coal outbursts."

Jan 1, 2015

By Ken Wangerud

The benefits of historic mining to this country have been many, but have come at a cost to the environment that has only begun to be understood over the past twenty years. While estimates vary, it is generally recognized that there are over 200,000 inactive and abandoned hardrock mines, with most of them located in the western U.S. Only a fraction of them are believed to be sources of metal releases with significant adverse environmental effects to the watersheds and receiving streams. State water-quality and natural resource management agencies have noted that hundreds of miles of streams are metal-impacted, and the aggregate effects of these sites within watersheds and drainage basins is poorly understood. Resources for the environmental assessment of abandoned mine land (AML) sites and watersheds have been and continue to be limited. Few hardrock mining states receive substantial reclamation funds under the (coal) Surface Mining Control and Reclamation Act. EPA Region VIII (EPA8) has an estimated 90,000 abandoned mining, milling and smelter sites, mainly in Colorado, Montana, South Dakota, Utah and Wyoming. An estimated 13,000 of the sites may have metal releases causing Clean Water Act and CERCLA non-compliance. Results of inventories by states and federal land managing agencies, indicate it is plausible that only 3,000-4,000 of these sites may be causing significant environmental degradation.

Jan 1, 1999

By Edward W. Parker

(Toronto Meeting, July, 1907.) NOTE.-The material from which this paper has been prepared was collected for the U. S. Geological Survey Bulletin, Contributions to Economic Geology, 1906, and appears also, though in somewhat more extended form without illustrations, in that publication. ALTHOUGH the briquetting of coals and lignites has been carried on for many years in Europe, and has reached a particularly high state of development in France, Belgium, and Germany, it has made comparatively little progress in the United States. The causes for the backwardness of the United States in this regard are several, and first among them has been the abundant supply of cheap raw fuel with which the manufactured article has to compete. With our millions of acres of coal-productive territory, from which the product can in most cases be cheaply extracted, it has appeared in many districts more economical to waste the slack or culm, which con¬stitutes a considerable percentage -of the product, than to attempt to save it at the additional expense required for briquetting. It is for this reason that the view in all sections of the anthracite-region of Pennsylvania is marred by the unsightly culm-banks which encumber the ground, and that in some of the bituminous-districts one sees huge piles of unmarketable- slack allowed to burn up in order to get rid of them. When the coal is of a coking quality, or when the slack can be used for steaming-purposes, these losses are not sustained, but many thousands of tons of what might be converted into usable fuel have been wasted every year simply because of the increased expense involved in its preparation.

Sep 1, 1907

By Brian M. Harney

The technique of remote sensing, used for many years by earth scientists, is being applied to the detection and monitoring of air pollution. Instrumentation being developed is of a very diverse nature and is effective, Fn varying degrees, at ranges from 1,000 meters to the altitude of a space satellite. This paper describes a number of the recent developments in this new field. Instruments based on spectroscopic, laser, and photographic systems are discussed. Sensors are being developed which utilize correlation spectrometry, interferometry, Raman scattering, Mie scattering, laser line absorption, and simple photographic detection.

Jan 1, 1973

By Frank Pollard

The Australian coal industry over recent years has experienced the situation whereby exploration and mine development are moving into geographical areas where the coal seams have never been mined to any extent in the past, if at all, and particularly where there is no history of experience in preparation of these seams. Additionally, the demands have been such that the development of a mine up to production stage should proceed with minimum delay. This is a situation which is of some importance and concern, in view of the coal quality requirements now experienced within world markets which can only be met, in most cases, by careful preparation. Costs are such that the preparation plant should operate as required by the situation and with maximum efficiency, which means that laboratoty information of breakage and washability characteristics which are required for preparation plant design should be accurate and available as soon as possible, even to a certain extent during the progress of the exploration.

Jan 1, 1981

The 3.5 million tones per annum Enterprise mine is the newest underground copper mine at Mount Isa in northern Australia. At a depth of up to 2000 metres, it is the hottest and deepest mine in Australia. In situ rock temperatures sometimes exceed 60¦C requiring the installation of substantial amount of refrigeration to provide safe working conditions for mine workers. The latest refrigeration project at the mine, R67, required the design and installation of the worldÆs largest bulk air cooler and AustraliaÆs largest chilled water plant. The plant is mounted on the surface of the mine and provides 25 MW of refrigeration to cool some 580 kg/sec of ambient air to 11.4¦C. This is equivalent to the production of 6300 tonnes of ice per day. The plant was designed for high availability, as any downtime would result in substantial production losses to MIM, and also had the potential to quickly result in unsafe levels of heat stress within the underground workplaces. The bulk air cooler has been designed for a capacity of 34 MW(R), the expected ultimate carrying capacity of the 7 m vertical intake shaft. Being located well inside the tropics, technical issues such as control of thermal pulldown required special consideration. Also, the bulk air cooler had to be designed to handle whatever demand for fresh air was imposed by the mine below, with over 100 per cent variations in airflow expected, and without loss of thermal efficiency. A substantial program of risk assessment and HAZOP studies was used to protect underground miners from leaks of ammonia into the air or water circuits. Fully automatic control systems result in a totally unmanned plant that is supervised remotely. To improve efficiency, the plant is controlled by the outlet air temperature from the bulk air cooler û the first in the world to be controlled in this fashion. Engineering solutions to address environmental considerations were incorporated at the design stage through features such as the use of ammonia (a greenhouse-friendly gas) as the refrigerant, zero atmospheric discharge and a wastewater collection and re-use system.

Jan 1, 2002

Editor's note: Biographical information about Ihor Kunasz, president, Newmont Uzbekistan, can be found in the February 1998 issue of ME, page 94 and in the May 1996 issue, page 92. Your personal assessment of the minerals business. Gosh! When I think about what has happened to the minerals industry over the past 27 years that I have been a member of SME! There have been fundamental structural changes in the industry. And I think that SME has been quite successful in coping with these changes as well. There has been a reorientation in how the minerals industry does business. It used to be called rationalization. Today we call it reengineering. In addition, the minerals industry has become more complex and more global. Shareholders have become more vocal and demanding in the management of the business, asking for protection of their shareholders' value. In the 1980s, a fundamental change was precipitated by a merger and acquisition fever in all industries, including the minerals industry. Raiders such as T. Boone Pickens put enormous demands on companies that, in turn, had to spend substantial management time to fend off the raiders. This resulted in a major restructuring of the mining houses. Today, for example, Anaconda, Kennecott and Amax are only historical names.

Jan 1, 1998

By Charles A. Lindberg

Mobile cranes on tires are perhaps the most important accessory in truck-haulage pits. They usually are of 20-ton capacity at short radius and with outriggers but have considerable overload capacity. Standard booms are 30 ft but have 10-ft extensions with which they are usually operated. Cranes have two engines, both originally gasoline, but 150-hp Diesel engines have been found more reliable for the propulsion motor, the 100-hp gasoline motors being retained for hoisting. Pro- visions are made for dropping the ballast counter- weight to reduce axle weights to legal limits for highway travel. The weights are carried on a regular truck or are transported on an extra trailer axle behind the crane. Tractors-Probably equalling the cranes in usefulness are the track-laying tractors which are used to prepare roads and other surfaces, to clean up at the shovel, and for dozing on stripping dumps. A new type of tractor mounted on rubber tires has been tried out on the Mesabi Range for the past year and a half. The advantage of this design is its mobility which makes it capable of taking care of the spill at the shovel and then running to the dump to clean up. Alternating between these two jobs, it relieves heavy tractors that can be used to better advantage on heavier work that does not require so much traveling. This tractor can travel at speeds of 12 to 13 mph and is designed to facilitate repair of the expendable parts. Weaknesses have developed in the internal construction which have seriously marred the performance record of this unit, but when used within its capacity it is quite successful.

Jan 1, 1949

By Y Lanwin

The Australian mining industry, a cornerstone of the nation’s economy, is on a journey towards greater equity and inclusion. Th paper introduces a comprehensive exploration of how universal design principles, stemming from architectural roots, have evolved through automation and digital technology into the more encompassing frameworks of inclusive design and equitable design. The paper proposes a practical framework for those involved in work, facilities and equipment design in the mining industry to identify and assess for equity and inclusion. Universal Design emerged in the 1960s with a primary focus on architecture, aiming to create spaces accessible to people of all abilities. Its foundational principles sought to ensure equitable use, flexibility, simplicity, perceptibility, tolerance for error, low physical effort and optimal spatial considerations. Over time, these principles evolved and expanded beyond physical spaces, finding applications in various fields, including technology, education and transportation. In response to advancements in technology and a growing understanding of the multifaceted nature of diversity, Universal Design evolved into Inclusive Design. Inclusive Design goes further than mere accessibility, considering a broader spectrum of users with varying cognitive, sensory, cultural and socio-economic backgrounds. It emphasises user centred design, customisation options, diverse user research and continuous iteration. Equitable Design emerged as a framework that addresses not only the diversity of needs but also systemic disparities. It emphasises fairness, justice and the elimination of structural inequities. Equitable Design encompasses accessibility and affordability, representation and diversity, ethical considerations and community engagement. This paper will explore the applications of these design principles through a series of case studies including village and on-site facilities, remote operations and office based work design and technology design. By applying these frameworks in a mining context, the paper proposes that mining companies and suppliers can improve diversity, equity and inclusion leading to safer, more engaged and productive workplaces.

Apr 16, 2024

By Gleason

"From June 16 to 19, more than 1,400 tunneling and underground construction professionals gathered in Chicago, IL for the bienial Rapid Excavation and Tunneling Conference (RETC). There, they were greeted by a full technical program and an exciting exhibit hall that provided a comprehensive look at the world’s bustling tunneling and underground construction industry.The successful conference was a reflection of the industry itself, which is to say, busy. As much of the world has begun to focus on creating a cleaner and greener environment, the global tunneling industry has seen an uptick in infrastructure projects move from design-build to construction phase. With a global shift away from the use of fossil fuels, major cities around the world are looking to increase public transportation options, which leads to the need for more transportation tunnels. And as urban populations continue to grow, the need for clean water calls for more tunnels, and as urban footprints continue to expand, the need to increase and update combined sewage overflow tunnel grows with them.During two and a half days, more than 20 sessions covering all of these topics were presented at the Hyatt Regency in Chicago, many to packed rooms in which every seat was taken and people were standing along the side and back walls.RETC is a biennial conference and one of the largest in the North America for the tunneling and underground construction industries. As such, it hosts a robust exhibit floor. This year 172 vendors occupied 205 booth spaces. The exhibit included everything from tunnel boring machine manufacturers, like Robbins and Herrenknecht, to the companies that supply all kinds of parts and services to the industry."

Sep 1, 2019

By Russell A. Carter

Alaska is a land of immense proportions and resources. Its very name, derived from an Aleut term, means "The Great Land." Yet, in a state slightly larger than Texas, California, and Montana combined, there are presently only two-large scale mines in production, excluding dredge operations. Once referred to by its territorial governor as "a storehouse of minerals," Alaska is, in the opinion of many industry observers, at least 20 years away from a healthy, productive mining industry. The mineral potential of the state is tremendous: coal deposits on the North Slope alone have been hypothetically pegged at 1.5 trillion tons. Copper-zinc deposits on the south flank of the Brooks Range are conservatively estimated to be worth $4 billion to $6 billion. However, the problems facing mineral development are of equal magnitude, and include:

Jan 11, 1976

By Paul F. Kerr

The insufficiencies of our mineral resources are becoming well known, and the national political conscience seems to be troubled at last by our dependence upon mineral commodities which must come from other lands. This realization places increased responsibility upon the industrial, educational, and governmental groups whose task it will be to solve the problems of mineral supply. As we all know, from the time that man first sought mineral deposits until recent years, prospectors have been largely responsible for mineral discoveries. Today the era of the prospector is almost over. The human ants that have literally examined all accessible outcrops and have tested the gravels of nearly all stream beds in the United States have left undiscovered few worthwhile mineral deposits within the scope of their recognition. The pages in the history of mineral exploration are now being turned from the era of the surface prospect to the era of the hidden de- posit.

Jan 1, 1949

By Harold L. Riley

This Bureau of Mines paper describes the methods and practices used at the Peck quarry of the Crab Orchard Stone Co., Inc., one of the leading producers of dimension stone in the Crossville, Tenn., area. The product is marketed under the registered trademark "Crab Orchard Stone". Another large producer of stone from the Crossville district sells its product under the registered trademark of "Tenn-Quartz". Both companies, and a number of other companies and individuals who quarry and process dimension stone from the same general geological formation, are members of the Quartzite Producers Association of Tennessee. The salable product is shipped throughout the country for use as architectural building stone. In 1959, 653,008 cubic feet of stone was produced in the Crossville area and was sold for $1,414,405. Terms and descriptions used in this report are those of the quarry and building trades. The offices, pitching sheds, wire saws, railroad siding, and storage areas of the Crab Orchard Stone Co., Inc., are on a side road 0.3 mile north from a point 2.2 miles east of Crossville, Tenn., on U.S. Highway 70. The quarry is on this same side road 2.0 miles south of Highway 70. Crossville is 62 miles west of Knoxville and 65 miles northeast of Chattanooga, Tenn.

Jan 1, 1962