Search Documents

By Rudolf Gahl

SOME time ago the Detroit Copper Mining Co. had to decide the question whether it would pay to re-treat slime-tailings, and several machines were tested in order to ascertain the type of construction which would give the greatest saving. In previous tests on the ore of this company, several tables proved far inferior to the Frue vanner, and for this reason they did not receive any serious consideration. In the late tests, however, one table was found to surpass the vanner in the percentage of saving made. The Frue vanner used in these tests had been adjusted approximately to the slope which the slime-vanuers in the concentrator of the Detroit Copper Co. had at that time, about 2 in. between the inside of the wooden posts, or 0.272 in. per ft. It had not been determined, however, if this slope was the most economical one for treating the slime-feed in the mill, or for re-treating the tailings from the slime-vanners, and I was instructed to ascertain by test-runs, under different conditions, the best adjustments for the work to. be done. In order to determine if a change in the adjustments of the machines would improve the results, it seemed sufficient to continue running the tests between the vanner and the table before mentioned, keeping the feed and all other conditions the same, but. varying the adjustments of the vanner .from run to run. I employed a vanner-man of long experience to operate these machines, who expressed the opinion that a slope between 2 3/8 and 2.5 in. between the posts (0.323 and 0.340 in. per ft.) would give the best results. Some runs made this way gave a considerable improvement. While for a slope of 2 in. (0.272 in. per ft.) the saving had been only 40.5 per cent. of that of the table, it .was 49.2 per cent. for 2.5 in. (0.340 in. per ft.) slope. A decrease of

Sep 1, 1909

By T. G. Chapman

This paper has been abstracted from a forthcoming Bureau of Mines bulletin on the concentration of copper ores in North America. GENERAL DEVELOPMENTS IN CONCENTRATING COPPER ORES FROM 1912 TO 1932 During the east 20 years the milling of copper ores as practiced in the larger concentrators has chanced to such an extent that comparatively few of the machines in use at the beginning of this period remain in service today. Concentrating Practice in 1912. In 1912 the usual equipment for concentrating copper ores comprised jigs for the coarser sizes, tables and sand vanners for the intermediate sizes, and vanners for the finer crushed and ground material. Rolls operated in series under graded crushing conditions, were in common use for the liberation of the copper minerals; grinding by Chilean or Muntington mills ordinarily was confined to the coarser tailings of jigs and tables.

Jan 1, 1934

By G. G. Eichholz

SUMMARY RADIOACTIVE dynamite has been prepared by introducing a small amount of antimony-124 into the explosive. Test work is described on the effectiveness of this tracer, on radiation levels in its neighbourhood, and on different methods of .application. Factors determining the choice of isotope, amount of activity, and overall cost of this process are discussed. INTRODUCTION Instances are known in which dynamite remains unexploded in drill holes in mining operations. Usually such 'bootlegs' are easily located by inspection of the face and the powder is removed before subsequent drilling is started. Occasionally, however, serious accidents occur because workmen drill into an undetected piece of dynamite. In order to avoid such accidents it was suggested that a different method of location might be tied, such as that afforded by the use of radioactive tracers. This paper describes some experiments that were carried out under the auspices of the Department of Mines and Technical Surveys, with the active co-operation of Canadian Industries Ltd. and Canadian Refractories Ltd., to test the feasibility of such a scheme.

Jan 1, 1957

"On-site research and development as well as in-situ testing are key factors to the successful implementation of new mining equipment and technology. Unfortunately the demands and necessities of research and development often conflict with the reality of mine production in operational mines, especially during early stages of research and development and the initial testing of new equipment. Several experimental mines under university supervision attend to this problem and provide a close-to- reality testing environment for the mining industry and mining equipment manufacturers. This paper gives an overview of the design and organization of such an underground testing area as well as of the wide range of possible operations it can facilitate at the example of the FLB Experimental and Teaching Mine (Forschungs- und Lehrbergwerk) at Technische Universität Bergakademie Freiberg, the central European underground research mine. INTRODUCTION As well as the Mining Engineering education follows the same pattern worldwide, the tasks and duties to be fulfilled by engineers in the productive mines are comparable around the globe. This also holds true for the technologies and equipment needed, both in surface and underground mines. Almost all mining equipment brands are being distributed worldwide. The tasks and challenges of guaranteeing an ever- increasing productivity at the mines, while simultaneously maintaining, respectively improving, safety standards, also in the developing countries and emerging economies, requests a constant development, improvement and adaption both of the engineering education and of R&D in technology and equipment. The increasing safety requirements at the mines, in combination with also increasing safety and liability policies, do often not allow a proper practical education of mining engineering students. At the same time, new technologies and equipment to be deployed / brought to the mines have to be fully functional in a production operation from the very first moment. Time losses like break-down time or even repair and maintenance breaks are often costly and, even when expected up to a certain degree with newly developed machines, have a wider negative impact on the neighboring operations and operations within that mine, thus often being unacceptable within the ongoing production process and extremely costly."

Jan 1, 2015

By Samuel P. Polack

This report reviews investigations to determine the fire hazard in coal mining when using flammable petroleum hydraulic oils to actuate mining equipment and summarizes research by the Bureau of Mines and industry on fire-resistant hydraulic fluids. Tests were established to evaluate fire resistance and the necessary characteristics to assure adequate service when fire-resistant fluids are used to replace petroleum hydraulic oils. The research was conducted in the laboratory and field trials under actual operating conditions in underground mines. Bureau of Mines Schedule 30 became effective December 17, 1959; the first approval was granted on February 18, 1960, and the twelfth was granted on March 17, 1961. The approvals include nine ready-mixed (by the producer) fluids and seven concentrates to which water is added by the user according to instructions from the producer. Seven synthetic-type fire-resistant hydraulic fluids submitted by two producers are also approved. Over 100 coal mines are now using water-in-oil emulsion-type fire-resistant hydraulic fluids in varying degrees from a trial in one machine to all the hydraulic equipment in an entire mine.

Jan 1, 1961

By Jim Smith, Jeff Hudreth, John White

Jan 1, 2000

By K. C. Sclater

GAS as a factor in the efficiency of oil production, might be a better title for this paper as it deals in general with the significance of the gas-oil ratio as an index of the efficiency of oil production and briefly discusses oil production methods with reference to the gas-oil ratio in wells, particularly during the early life of a field. In the recent hearings held at Washington before the Federal Oil Conservation Board the fuller utilization of the energy contained in the gas occluded in or associated with the oil underground was stressed by some of the speakers when referring to greater ultimate recovery of oil. One speaker commenting on this point said in part, "There is ample evidence indicative that if the gas associated with the petroleum in our fields were conserved and elevated gas pressure maintained in the oil sands during their productive life, the ultimate production of oil could be greatly increased."

Jan 1, 1926

By P. Raghavan1

Reverse froth flotation experiments were carried out in the laboratory using two different types of kaolins for the separation and removal of coloring titanoferrous impurities from cryo-filtered clay after subjecting to high shear pre-treatment. This high shear pre-treatment consists of high shear agitation of a high solids clay slurry with the dispersant (high shear dispersion, HSD) followed by high shear agitation with the collector (high shear conditioning, HSC). After this pretreatment, the slurry is diluted and reverse flotation is carried out. One sample is from, Gujarat, India (Mamuara clay, ?MC?) while the 2nd sample is from Amberg, Germany (AKW clay, ?AC?). While MC consisted of 89% particles below 2µm and analyzed 1.06% of TiO2 and 0.29% Fe2O3 and measured a brightness of 83.4 %ISO, the corresponding values for AC are 67% below 2µm, 0.3% of TiO2? 0.49% Fe2O3 and 83.4 %ISO. The flotation performance is found to be greatly influenced by the conditions of high shear treatment. Important variables are HSD intensity (rpm), HSD time, HSC intensity (rpm), HSC time, HSD/HSC time ratio, ?HSD+HSC? total time etc. Higher shear intensities favor both the impurity liberation and collection. For both clays, it could be shown that impurity removal increases as total pretreatment time (?HSD +HSC? total time) increases up to a certain limit. For MC, the HSD time was only half or less than that of HSC time, while for AC, HSD time is at least twice (or more) than HSC time which is just an opposite manifestation. This is believed to be due to the striking differences between these two clays. Most importantly, the shear frequency is found more influential than the shear rate for the overall flotation performance for both clays. Interestingly, at high shear frequencies, i.e., when a stirrer with more number of teeth on the rotor is used, the ?HSD+HSC? total time is greatly reduced. Again, increased shear frequency helps to reduce flotation time and significantly improves flotation performance. At optimum conditions, product titania reduced to 0.35% for MC whereas the same reduced to 0.13% for AC. The product of flotation of MC measured 85%ISO brightness while that of AC measured84.6%ISO thus enhancing the value of the final product. It could also be established that the high shear pre-treatment shows better flotation performance than that due to collector dosage. Keywords: high shear dispersion, high shear conditioning, titanoferrous impurities, shear rate, shear frequency, brightness, clay recovery, Mamuara clay, AKW clay

Sep 1, 2012

By Sarkis G. Ampian

Crystalline silica (quartz, cristobalite, and tridyrnite) is regulated by the Mine Safety and Health Administration (MSHA) and Occupational Safety and Health Administration (OSHA) because of its potential for causing debilitating but nonmalignant lung diseases. In 1987, the International Agency for Research Against Cancer (IARC) conducted a review of the health literature and concluded that crystalline silica was a probable human carcinogen. As a result of this finding, OSHA was required to regulate crystalline silica under its Hazard Communication Standard (HCS). The standard requires that all materials handled by OSHA-regulated facilities be labeled according to the requirements of RCS and that workers receive proper training on the handling of the material if the crystalline silica content equals or exceeds 0.1 weight percent (0.1 %). MSHA currently is considering enacting its own RCS. This will be similar to OSHA's RCS. If the standard is enacted, most mineral producers will have to determine the respirable monitor filter and bulk crystalline silica contents of their ores and products so that workers and/or customers will know whether they are in compliance with the 0.1% HCS and/or the OSHA permissible exposure level (PEL) of 50 µg for an 8-hour workday for respirable crystalline silica as determined from monitor samples. Two major concerns with the RCS are the widespread occurrence of crystalline silica in nature and the suitability of current technology for routinely determining crystalline silica concentrations at the 0.1 % RCS level. Most ores are extracted from silica-bearing deposits and it is a common constituent of rocks and soils. OSHA's RCS will have the greatest impact on the producers of crushed stone, diatomite, dimension stone, gravel, industrial sand, perlite, pumice, pyrophyllite, sand, and talc because these materials frequently are shipped directly from the mill to the customer. MSHA's RCS would affect nearly all mineral producers. Those producers that have crystalline silica present in concentrations near the 0.1 % cutoff point will have the most difficulty with the analysis. Crystalline silica can be quantified at the 0.1 % level by X-ray diffractometry in simple systems containing one, two, and possibly three minerals if (1) none of the accessory minerals has X-ray diffraction reflections that coincide or overlap with those of crystalline silica and (2) the standard has a particle size distribution and crystallinity similar to those of the sample. In some instances, it may not be possible to determine the crystalline silica content of a sample with any degree of certainty using the recommended regulatory protocol. In all cases, it is recommended that a qualified mineralogist identify the minerals in a sample prior to any regulatory analysis. Additionally, the uncertainty as to whether some silica polymorphs should be classified as crystalline or noncrystalline and the suitability of metastable high-temperature standards, such as cristobalite and tridyrnite, for regulatory analysis at ambient temperatures should be addressed further. This overview is written both to highlight these problems and to serve as a guide for analysts, regulators, and industry personnel who are involved in the crystalline silica issue. It also covers some of the difficulties and/or shortcomings in quantifying crystalline silica, such as the ubiquitous mineral quartz, in the workplace.

Jan 1, 1992

By W. Kempson

"As has been noted on numerous occasions, the vertical shafts being sunk around the world are all tending to get deeper as we seek to take advantage of higher grades of minerals which can sometimes be found at greater depths. One of the challenges with these deeper shafts is the requirement to supply services to the mine’s operations at depth as well as the requirement to dewater the mine. Both the supply of water and the dewatering of mines is generally done using piping. With the greater shaft depths, this piping is now required to contain higher pressures as well as to accommodate changes in temperature resulting from normal mine operations. This paper will discuss the requirements for the design of high pressure piping in deep vertical shafts. The discussion will start with the general definition of the systems and the detailed design requirement. Once this is clearly outlined, we will discuss the options available for fulfilling these requirement as well as the advantages and disadvantages of each of the systems. We will finish with the installation recommendations and provide a basis for the maintenance of these systems. INTRODUCTION Piping in vertical shafts is used to provide a number of services in underground workings. These services vary depending on geographical location and the type of the ore body which is being mined. For example, in the Zambian Copper mines, one of the largest requirements for in shaft piping is for dewatering. Similarly in the Gold deposits in the West Wits basin as well as the deep level Copper deposits in Arizona, one of the largest uses for the piping is the supply of a cooling medium to underground workings to create a safe working environment (this can in the form of water or of glycol depending on the application). In South Africa, systems were installed which used the hydrostatic head which is generated from supplying chilled water to mines whose depths exceeded 2,000 m below surface. This chilled water was supplied as a closed system, allowing for high pressures to be generated which was then used to supply useful work (for example, Rock Drills, Face Cleaning and other ancillary services) whose power was traditionally supplied by compressed air or electricity. This system was initially researched by Chamber of Mine in South Africa. The design pressure range of these systems is 14 MPa to 18 MPa."

Jan 1, 2019

By C. H. Riggs, Kenneth H. Johnston

The application of modern secondary-recovery methods has made possible the the extraction of more than 13 million barrels of crude petroleum from the eastern part of the Delaware-Childers field Nowata County, Okla., over and above the production that might have :been expected by continuing primary production methods, including the use of vacuum. Foremost among the secondary-recovery methods used in this foil was the repressuring of the Bartlesville sand with air and gas through injection wells spaced on sym-metrical patterns. Between 1925 and 1945, about 51 billion cubic feet of air and gas were injected into the producing formation, and the total recovery was increased from, 25 million to about 40 million barrels of oil. To produce as much as possible of the 28 million barrels of recoverable oil remaining in the sand will require the initiation of systematic water-flooding projects on many properties and the continuation of air and gas injection on others.

Dec 1, 1946

By Alexander N. Winchell

"Location. The copper mines of Michigan are all in the northern part of that state on the Keweenaw Peninsula, which extends from the (Michigan) mainland for about seventy miles northeasterly toward the middle of Lake Superior. The mines occur in a belt or zone occupying the central portion of the peninsula from end to end.. The most productive mines for many years past have been those located not far from the city of Houghton in' the central part of the zone, in a section extending about ten miles southwest of Houghton and fifteen miles northeast. The most important mines in order of location, from the northeast to south¬west, are the following: Mohawk, Ahmeek, Allouez, North Kearsarge, Wolverine, South Kearsarge, Centennial, Calumet. and Hecla, Osceola, Franklin, Quincy, Hancock, Isle Royale, Superior, Baltic, Trimountain, and Champion. The first three named are in Keweenaw county and all of the others are in Houghton county. Still farther to the southwest are the Lake, Mass, Adventure, Michigan, Victoria, and White Pine mines. These are in Ontonagon county.History. The exploitation of these copper mines extends back into prehistoric times. There is little evidence that the American Indians carried on mining operations in this region in the period shortly before the advent of white men, but there is abundant evidence that the ancestors of the Indians, •or some earlier inhabitants of the region, carried on primitive mining operations. For example, Mr. S. O. Knapp, Agent of the Minne¬sota Mining Company, in the winter of 1847-48, made the first discovery of prehistoric mining. This event is described as follows by Foster and Whitney :"

Jan 1, 1920

By Winston W. Spencer

ALTHOUGH by far the largest A consumer of platinum metals in the world, the United States until recently has been in- significant as a producer. Writing in the "Minerals Yearbook" for 1939, H. W. Davis states that 1938 probably marked the beginning of an- other period of transition in the world production of the platinum metals. In that year, he says, their production in the United States jumped to 49,380 oz., or fourth in the rank of world output. In the ten-year period 1925 to 1934 United States output ,averaged only 8300 oz. Practically all of this sudden in- crease in production is attributable to the introduction of mechanized equipment at the placer deposits in the Goodnews Bay district of Alaska. This district adjoins the Bering Sea and Kuskokwim Bay (accented on the first syllable), and is approximately 120 miles south of the mouth of the Kuskokwim River. The nearest village and post office is Platinum, which lies about eleven miles north- east of the Goodnews Bay Mining Company's camp. A good gravel road connects the mine camp and the village.

Jan 1, 1940

By S. C. Grund

In secondary copper smelting as it is performed at Hüttenwerke Kayser plant in Lünen, tin-and lead-containing flue dusts are produced as intermediate products. These flue dusts are further processed in a hearth furnace. Followed by certain refining operations a saleable tin-lead-alloy is produced. Even though the hearth furnace technology has been in use for this purpose for a long time still its performance undergoes changes in search for optimum processing conditions regarding to the increasing complexity of the raw materials and tightening economical and ecological boundaries. The use of modern statistical tools for the calculation of accurate mass balances is demonstrated for the tin-lead hearth furnace. These reliable mass balances are the basis for any further modelling of the process with the aim of optimization. Incorporating metallurgical knowledge and experience as well as different mathematical modelling techniques, further studies are planned in which the recoveries of valuable and minor elements and their dependency from various process parameters are examined. The aim of this modelling is to optimize the recoveries of the valuable elements, to minimize the energy consumption and the processing costs and thus to keep the process competitive in a harsher economical and ecological surrounding. The modelling principles are transferable to other metallurgical operations and are especially suited for ill-defined pyrometallurgical processes.

Jan 1, 1999

By S. L. Windes

"INTRODUCTION For a number of years, the Bureau of Mines conducted tests on various types of structures to ascertain the effect of seismic vibrations emanating from quarry blasting in an effort to determine an index of damage. Associat¬ed with these tests, occasional records were made of the characteristics of the air blast or concussion from the explosions. Although the importance of the air-blast problem was recognized, the equipment was not designed for airblast measurements, nor was the early research program concerned with the problem. After the ground-vibration tests had been completed, attention was turned to study of the air blast and its effect. The program was modified, however, in certain aspects by the imminence of war and the final entry of the United States into the conflict. These modifications were made to supply information pertaining to military and civilian defense problems.Detailed discussion of these problems is beyond the scope of this report, which attempts to present preliminary results of factual and fundamental character. However, it may be noted that airblast data are urgently needed for intelligent design of both Government and non-Government buildings, which must withstand the air blast from bombs and afford maximum protection for the occupants. The safety of vital equipment above and below ground necessitates consideration of damage from air blast. Protection against use of dynamite by saboteurs, moreover, hinges largely on the effect of air blast. Identification of a planned ""accident"" involving dynamite often entails knowledge of the characteristics and power of the airblast.The peacetime problem of damage from air blast resulting from quarry and mining blasting activities is of course exaggerated by the wartime requirements of increased production accelerated operation, and enlarged development."

Jun 1, 1943

By Albert L. Toenges

The fuel requirements for industrial and domestic consumers in New England, in normal times, are supplied almost entirely by fuel oil, anthracite, and bituminous coal. A shortage of these fuels occurred during the war. This shortage was caused by: (1) The diversion of oil to military uses; (2) the use of railroad and boat facilities that ordinarily would transport coal for the transportation of war material; (3) the inability of coal mines to apply the increased demand for coal which resulted from the conversion from oil to coal by domestic and industrial consumers; and (4) the increased demand of war industries for coal. Because of this Critical fuel situation, an investigation was made of possible sources of fuel nearer to points of consumption in New England.

Jan 1, 1948

One of the earliest and continuing challenges in driving sustainable development in large scale resource industry projects is around the issue of assessment û how do you measure the sustainability of a mineral operation? One of the key road blocks when confronted with this challenge is the temptation of technical folks to reach for a definition of sustainability or sustainable development. But definitions, by definition, have boundaries and limitations that serve to constrain thinking û they limit the thinking of what we can achieve with sustainability (it also acts as a barrier that constrains innovation). Rather than seeking definitions, better understanding of the core perspectives around sustainability and their application to the minerals industry provides a much more powerful platform from which to conduct assessments. But it is only when these perspectives are combined with the right framework and supporting techniques that the complex becomes doable. With the support of the perspectives and the framework, various assessment and measurement methodologies can be used; the challenge is communicating to stakeholders the sustainability character of the project in ways that are meaningful and to which people can connect. Assessment is not about finding the best or most accurate methods that fulfil strictly academic and possibly abstract requirements. The challenge is to help people understand what the impacts are, and what the value contributions will be, in a format and language that make sense in their world-view.

Jan 1, 2009

By James M. Link

The transportation of solids by slurry pipeline is a rapidly growing field. Although early patents date from the latter part of the nineteenth century, it has only been within the last twenty years that successful long distance slurry transport lines have come into their own. The pioneering efforts in this country include the gilsonite slurry pipeline from Bonanza, Utah, to Grand Junction, Colorado, and the coal slurry pipeline from Cadiz to Cleveland, Ohio. Both of these lines were constructed in 1957 and had a combined annual capacity of about 360 million ton miles. Although the Cadiz pipeline was mothballed in the early 1960's, the interest in slurry transport systems continues to increase and one engineering and construction company is predicting that by 1980 an annual slurry system rate of more than eight billion ton miles will be achieved. The design and construction of cross-country pipelines for fluids such as crude oil appears relatively simple when contrasted against the complex problems encountered in slurry systems. Considerable effort has been expended in hydraulic research laboratories in an attempt to improve our understanding of slurry behavior. This effort has been rewarded with considerable success and is best illustrated by the large number of slurry systems now planned or under construction. However, slurry transport in pipelines is still, in many instance more of an art than a science. In order to minimize the risk factors in the construction and operation of large scale slurry systems, studies are frequently conducted in pilot scale test

Jan 1, 1972

By K. J. G Hedges

"Once a health based guidance limits for exposure to diesel exhaust have been established, and as part of a multi-disciplinary team, the program for exposure reduction should incorporate the plan-do-check-adjust cycle. Setting a suitably protective (health based) occupational exposure limit (OEL) for diesel particulate matter (DPM) and nitrogen dioxide is a key driver to reduce exposure. It is important to go beyond regulations and reduce exposure to diesel exhaust, DPM, as low as reasonably achievable (ALARA) such as that prescribed under the Australia, Queensland Mining and Quarrying Safety and Health Regulation 2017 where under section 135 Limiting workers exposure, the workers exposure must not exceed the exposure limit applying to the worker for the hazard; and is ALARA. It appears that previously acceptable OELs are no longer safe. Therefore it is important that the internal responsibility system be implemented and the precautionary principle approach be followed, especially as it may be some time before a suitably protective OEL specifically for DPM is in place. One leading multi-national mining company BHP Billiton has acknowledged a significant lag that exists between regulatory action and the level of science that informs health risk. This company is managing exposure to diesel exhaust to as low as technically feasible. This same company that has set an interim target for managing diesel exhaust to 0.03 mg/m3 is achieving these levels which paves the way for other mining companies and general industry including construction. The Occupational Cancer Research Centre 2017 recommends reducing personal exposure to within 0.02 mg/m3 (EC) for underground mining and 0.005 mg/m3 for other workplaces. Controlling DPM is important to prevent cancer however it is also important that that nitrogen dioxide (NO2) be reduced (ALARA) and that careful selection of control technology be considered such as the proper selection of a diesel oxidation catalyst so that the level of NO2 does not in fact increase. The example from BHP Billiton provides a leading practice including using a multi-disciplinary approach and the importance of controlling emission at source and having an auditable diesel emissions based monitoring program in place."

Jan 1, 2019

By Charles W. Perry

The options of enhanced oil recovery, coal syncrude, and shale syncrude are compared by approximately equivalent economics. The physical constraints for the major enhanced oil recovery processes are described, followed by new estimates of cost. The range for all three options in terms of light syncrude equivalent are $22 to $40 per barrel in 1980 dollars.

Jan 1, 1982