Search Documents

By G. A. Vissac

The drying of fine coal involves special techniques, which are discussed and analyzed. Types of dryers employing these techniques are described. Calculations are presented for new methods of dealing with the entrained dust that is always present in fine coal drying operations. NEW conditions, new requirements, and new methods have increased the demand for more efficient and more economical methods of drying fine coal. Dewatering of larger sizes may reduce the surface moisture to 8 or 9 pct. It is more difficult, however, to dewater sizes below 1/4 in., and some filter cakes still contain as much as 20 or 25 pct moisture. Increased freight rates and stricter consumer specifications have resulted in a demand for further reductions in moisture content. This can be obtained only by heat drying. Most modern methods of heat drying disperse or spread the mass of coal to be dried, in an atmosphere of dry hot gases. The more intimate the contact between coal particles and hot gases, the quicker and more efficient the drying operation will be. Two different techniques are generally employed, using either a fluidized condition or an entrained condition of the coal to be dried. Fluidized Condition Fluidization of a body of sand was defined and explained by Fraser and Yancey in a paper published in 1926.' This condition was artificially obtained and maintained by proper regulation of the rate of air flowing through the sand body. "The sand bath 'boils' uniformly on the surface," they write, "and feels like a fluid." The fluidization technique was also described and analyzed by Steinmetzer2 in connection with the operation of an air cleaning table. His main conclusions are as follows: "Fluidity is, for the particles involved, the possibility of motion with minimum friction. . . . Then fluidity requires the introduction of various forms of energy capable of neutralising frictions. Two solutions can be used— air and/or mechanical motions (such as the shaking motion of the carrying deck of the air table). The combination of mechanical and air energy will give the widest margins of size ratios and of bed thickness, translated in capacity per unit area of the carrying table." Richardson and Langston3 have indicated results obtained with a dryer working with a fluidized bed. They used a vertical tube type of dryer, however, without the assistance of any mechanical energy, and without any lateral motion of the fluidized bed. The capacity of such a dryer is too limited for practical applications, since the speed of the acceptable air currents is held to the speed of fall of the particles involved. Capacities as low as 182 Ib of coal per hr per sq ft of dryer area are indicated. As stated by Richardson: "A basic limitation to a fluidised bed dryer is that the velocities of the gas must be held within a definite range; with velocities of 10 ft per second, all coal minus 6 mesh in size will be entrained, and the operation is then similar to that of a Flash dryer." A fluidized bed must be virtually static. The coal particles simply kept in suspension offer a minimum resistance to the flow of gases, insuring the most favorable conditions for rapid evaporation of surface moisture. However, very wet fine coal, i.e., over 12 pct of surface moisture, will be delivered in the forms of mud balls, or as a soggy, sticky mass, almost impossible to disperse, sticking and acting as a wet blanket on the deck. Strong currents of gases and wide deck perforations will be required to punch holes in the wet mass and gradually loosen and fluidize it. The mechanics of fluidizing a bed of coal in a gas medium for the purpose of obtaining the most efficient drying condition are entirely similar when the fluid used is water and the purpose is to break up and distend a bed of coal to be cleaned so that perfect stratification according to densities will be insured. Purely mechanical energy is used in the basket-type jig, water pulsations in the piston and in the Baum-type jigs. A combination of mechanical motion and of air pulsation offers the most efficient and favorable conditions. Entrained Condition The most critical factor to be considered in the design of a dryer employing the entrained condition technique is the speed of the hot gases to be circulated in the drying column. With insufficient gas velocity, excessive amounts of the largest sizes will drop to the bottom of the dryer column without being thoroughly dried. On the other hand, high gas velocity will cause degradation, dust losses, and high power consumption. Figs. 1 and 2, reproduced from Hanot,4 show the relative importance of speed and temperature for various sizes of particles. It can be seen, for instance, that to maintain in unstable equilibrium particles of 1/4-in. size in a gas current at 500°C, a speed of 30 meters per sec, or 6000 fpm, will be required. For % -in. particles an almost prohibitive speed of 45 meters per sec, or 9000 fpm, will be necessary. In practice, maximum gas velocities of 3000 fpm are recommended; since power increases as the cube of the velocity, it can be seen that beyond certain limits such dryers would not be economical. If the particles were moving at the same speed as the hot gases they would remain in the same

Jan 1, 1954

By Hillary W. Clair

An equation is derived for the rate of reaction of a sphere of metal oxide in a restricted enclosure through which a reducing gas is flowing . The equation takes into consideration the reaction rate coefficient , transport through the gas and through the porous shell of reduced oxide , the rate of gas flow , and the volume of the enclosure . The equation serves as a model for predicting the course of reduction of a particle of metal oxide in a shaft furnace .

Jan 1, 1964

By Clyde Baker

Drilled shafts for many situations offer an economical alternative to driven piles. The Federal Highway Administration (FHWA) has spent considerable time and money in research and developing design and construction guidelines for drilled shafts. However, the full potential of the technology may not be realized because of the uncertainty of the effects of construction on the actual service behavior and the lack of either reliable quality control tests to check for or evaluate defects, or inexpensive load test procedures. Static load testing is very expensive and it is not feasible to load test each shaft on a project. Therefore, other means are necessary to confirm or evaluate the integrity of the completed drilled shaft or to determine the capacity of the completed shaft.

Jan 1, 1989

By R. P. Beyer

As part of its thermodynamic investigations of mineral compounds, the Bureau of Mines has written an algorithm based on Newton's method for solving for the characteristic Debye temperature of a compound, from heat capacity and temperature data. A listing of a FORTRAN IV program based on this algorithm, for calculating Debye temperatures given heat capacities or for calculating heat capacities given Debye temperatures, is available from the author upon request.

Jan 1, 1981

By Slobodan Radosavljevic

The polymetallic W-Pb-Bi-Ag ore from the ?Nova jama? ore zone of the Rudnik ore field have been investigated. Contact-pneumatolytic (skarn), pneumatolytic-hydrothermal, and hydrothermal mineralization phases are defined in this ore zone. The most significant mineralization phase that gave compact ore bodies is pneumatolytic-hydrothermal phase. A relatively pure Mo-free scheelite is the only tungsten-bearing mineral. Lead minerals are mostly presented by Pb-Bi sulphosalts and much less with galena. The image analysis coupled with Energy Dispersive Spectrometry (EDS) analysis on a Scanning Electron Microscope (SEM) was applied to the characterization of a W-Pb-Bi-Ag ore as an efficient tool for mineral quantification. Results of EDS (Energy Dispersive Spectrometry) analyses gave the empirical formulae: Pb1.91Ag0.05Cu0.08Bi1.93S5 for cosalite, Pb0.98Ag0.03Cu0.05Bi1.99S4 for galenobismutite and galena Pb0.99Ag0.03S.

Jan 1, 2006

By W. J. Garmoe

The Carr Fork mine is located approximately 50 kilometers southwest of Salt Lake City, Utah, in the Bingham or West Mountain District, adjacent to the Bingham open pit copper mine. Applied geology at Carr Fork, by Anaconda Minerals Company personnel, includes detailed geologic mapping and sampling of underground workings, logging and sampling of drill core and cuttings, and the preparation and posting of geologic maps and cross sections for geologic interpretation, ore reserve calculation, mine operations, and long range planning. Accurate and easily understood graphic recording of Carr Fork geology is essential for optimum use by operating and engineering personnel. The design and implementation of exploration, development and definition drilling programs, research into geological spatial relationships, and analysis of structural complexities of the Carr Fork deposit are also integral parts of the applied geology program.

Jan 1, 1992

The traditional technological flow sheets for processing of ferrous quartzite (magnetite ores) al-low production of the iron concentrates with Fe content of 65%~68 % and recovery level about 55 %. The losses of iron with the tails of wet magnetic separation are related to hematite and quartz-magnetite particles, which are not extracted under low magnetic field employed. This work presents the results of the application of reverse cationic flotation for production of hematite concentrates with weak silica content from the tailings of wet magnetic separation of mag-netite. Fine particle size, complex mineralogy and presence of locked particles determine the impos-sibility of direct production of hematite concentrate by flotation or magnetic separation. The gravity concentration allows obtaining of iron concentrate from the well-prepared feed (size fraction -53+20 µm) but with very low recovery. Thus, hematite concentrates with weak silica content and satisfactory iron recovery were obtained by reverse cationic flotation, when it was fed with iron pre-concentrate produced by high gradient magnetic separation. The best flotation results were obtained by the use of formulations based on amines of different molecular structure that modulate the structure of adsorption layer, and favour a shifting of hydro-philic-hydrophobic balance on the surface of silicates with adsorbed starch and their preferential transfer into the froth product.

Jan 1, 2014

By J. R. J. Edwards

Jaspilite, a mineral consisting of silica and iron oxide in varying proportions, is one of the host rocks of the high grade ore deposits situated in the Middleback Range of South Australia. As a result of laboratory investigations, a flowsheet was postulated for the beneficiation of jaspilite to produce an acceptable grade product for feeding to blast furnaces, The flowsheet involved the reduction of the hematite in the haspilite to magnetite, the grinding of the reduced product to 95 pct minus 325 mesh Tyler followed by wet magnetic separation, hydroseparation and filtration to yield a magnetite concentrate. Agglomeration of the fine concentrate would then be necessary to meet the physical requirements of blast furnace feed. To prove the postulated flowsheet, to obtain a more accurate estimate of costs and to obtain design data for a commercial installation, a pilot plant was constructed at Whyalla, South Australia.

Jan 1, 1960

By F. H. Seymour

Central to Newmont Gold's Mine planning system is the ability to interactively perform cut and fill operations on topographic contours and to accurately evaluate grades and tonnages within contour outlines using polygon set manipulation routines. This paper develops the applied geometry concepts that underlie these routines. Included are representation of volumes with contours, point in polygon test, block proportion in polygon calculation, polygon area and centroid calculation, and intersection, union, and complement between polygon sets.

Jan 1, 1990

Rosebery Mine is situated on the west coast of Tasmania and is AustraliaÆs largest volcanic-hosted base and precious metals deposit (zinc, lead, copper, gold and silver). The milling operation has been producing zinc, lead and copper concentrates continuously for over 100 years. RoseberyÆs long life demonstrates the operation to be high grade, and high margin, capable of operating through several commodity price cycles. Paradoxically, throughout this long history the ælife-of-mineÆ as defined by proven and probable reserves has been short. Zinifex has demonstrated its commitment to discover the future of Rosebery with the growth project æProject HorizonsÆ. The aim of the project is to extend the life of mine beyond 2020, with an additional exploration expenditure of $19 million over three years. Despite the maturity of the deposit, early success has confirmed the potential with the discovery of new resources. Mine planning strategic studies are challenging established paradigms of mine production, throughput rates and metal cut-off grades. Discovering the optimal process rate for Rosebery, by examining the æHill of ValueÆ and underground mine optimisation is proving critical to the best exploitation of RoseberyÆs rich resources. The promise of finding a mine within a mine is being realised, with new lenses being delivered by exploration success and real grade/tonnage options optimised through dynamic mine planning. The future of Rosebery is co-dependent on these two areas of discovery. This ensures capital expenditure decisions are informed, to secure the next 20 years of wealth creation and beyond.

Jan 1, 2008

By G. McIsaac

This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development, and mining method. Based on practical considerations, maximum rates are set for each zone?s development and production capacity. For the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum daily development capacity is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Also, the fixed cost of operating the mine is taken into consideration whenever mining activities take place. Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analyzed. ?Whatif? scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan.

Sep 1, 2005

By Liang Li

Thermodynamic analysis and experiments were conducted in order to verify the feasibility of preparing crude titanium tetrachloride (TiCl4) via the carbochlorination of low-grade titanium slag in molten salt. Titanium slag, assaying 74.6 wt% TiO2 with high calcium and magnesium oxide impurities, was treated by an optimized carbochlorination process in NaCl molten salt. These impurities in the titanium slag were chloridized simultaneously, and chlorination products FeCl2, MnCl2, MgCl2, CaCl2 and CrCl3 were collected in the furnace slag. XRD and SEM/ EDS analysis of residue shown that SiO2 and Al2O3 in titanium slag were difficult to chlorinate completely. Theoretical calculations and industrial-scale experimental studies reveal the content of TiCl4 in the products was more than 98.8 wt% and thus proved the feasibility of utilizing low-grade titanium slag for TiCl4 preparation by molten salt chlorination technology.

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always have the same properties. The properties considered here, of course, are those inherent in the ingot immediately after solidification and not qualities imparted by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. Other variations in properties are due to variations in those constituents of steel (elements or compounds) that are not ordinarily included among the elements specified, thus not a part of the specified "composition." The term "constitution" is used to include not only the specified composition but also the nature and distribution of every element or compound contained in the steel entering the ingot mold ; also included are items such as aluminum oxides and nitrides, presence of soluble gases, and dispersion of nonmetallic particles. When it is considered that the constitution of steel is determined by the addition or absorption into the bath of all such constituents from whatever source, it follows that constitution is of necessity the final result of steelmaking practice. It is the agency through which steelmaking practice operates to control the properties of the steel. The term steelmaking practice is here used in the broad sense, meaning the control of all the materials entering the steel and of the conditions under which the process is carried out. Steelmaking practice, thus defined, establishes the chemical system within which the reactions between components must proceed in obedience to the laws of chemistry. Thus the chemical constitution of the steel is established and, through constitution, the properties of the metal are established. In the preceding chapters it has been shown how the constitu-

Jan 1, 1964

By L. W. Kempf

A BALANCED system of internal stress is set up in any metallic structure by plastic deformation below the annealing temperature. The internal stress induced by cold rolling or other fabricating processes is generally recognized and its magnitude is known to be, within certain limits, a function of the degree of cold deformation. The plastic deformation that may accompany rapid cooling from elevated temperatures may not materially change the form of the product. The internal stresses so induced are not, therefore, so evident and nonrecognition of their presence has at times led to engineering failures. The heat treatment of aluminum alloys is a relatively new art and little information is available regarding the magnitude of stresses induced luring the commercial heat treatment of aluminum alloy products is the industrial use of aluminum increases, it is inevitable that products of increasingly large volume be required. It has become necessary in the present commercial utilization of aluminum to heat-treat castings and forgings weighing hundreds of pounds. One of the factors governing the magnitude of internal stresses arising from rapid cooling at elevated temperatures is that of the, size of the structure being treated. Some of the other factors are: cooling rate, elastic properties of the alloy, thermal expansivity, thermal conductivity, and the presence or absence of phase changes. Practically all aluminum alloys have a high coefficient of thermal expansion and some are capable of developing relatively high

Jan 1, 1934

By George J. Dvorznak, Robert W. Waytulonis

The Bureau of Mines is conducting a research project in cooperation with the Mine Safety and Health Administration (MSHA). Mining companies, and equipment manufacturers are also participating through the Colorado Mining Association (CMA). The objectives of this cooperative research project are to determine the practicality of coupling a dry exhaust conditioning system (dry system) and diesel particulate filter (DPF) to make an integrated control system, and to determine the effectiveness and durability of the integrated system in an underground coal mine. Diesel-powered mining machines must be equipped with control devices to reduce surface and exhaust temperatures to safe levels and prevent flames and sparks from being emitted to the mine atmosphere. Diesel exhaust-gas water scrubbers have been successfully used for many years but they have several disadvantages; they are large, consume large quantities of water, and require frequent maintenance to remain functional. Additionally, diesel exhaust is a source of noxious gases and particulate matter. Particulate emissions are composed primarily of small carbon particles with absorbed hydrocarbons and they are almost entirely respirable in size. Even an engine in good mechanical condition can emit up to 400 mg/cu m of respirable particulate matter. A dry system for control of diesel fire and explosion hazards, coupled to a DPF, promises to be a complete control system for diesel engines. The dry system cools the exhaust and suppresses sparks and flame with a heat exchanger and flame and spark traps. The conditioner is smaller, consumes no water, and requires less maintenance than a comparable water scrubber. The DPF uses a ceramic substrate as a wall-flow filter and is very efficient at collecting exhaust particles. Average particulate mass collection efficiency is 90%. This report describes a cooperative research project to combine the dry system with the DPF, conduct performance tests on the integrated system at Bureau and MSHA 1aboratory facilities, and conduct field tests of the system on a production machine in an underground coal mine.

Jan 1, 1987

By Moyes A. J

The Intec Copper Process uses a strong chloride electrolyte at atmospheric pressure and 80 - 85¦C to produce high purity, 99.99 per cent copper granules and elemental sulphur. A recent, exhaustive study by an independent, major Australian corporation has shown the capital cost of an Inter plant to be approximately half that of a copper smelter at the 200 000 tpa capacity level and approximately half the operating and capital cost at the 50 000 tpa level. The Inter process costs were also shown to be greatly superior to the best available leach/SX/electrowin technology. The process utilises a multi-stage counter current leach at 80 - 85¦C with the addition of air at atmospheric pressure to precipitate iron as a goethite type compound, followed by a two-stage purification process separating impurities in metallic- and other forms. Purified cuprous chloride/sodium chloride solution is fed to an electrolytic diaphragm cell where high purity copper granules are produced at current densities of 1000 - 1500 A/m2 withoutthe need for conventional electrode stripping. Power consumption is approximately half that of the cupric route. The product is suitable for the direct powder metallurgical conversion of the granules to products such as wire or strip. All the steps in the 'furnace free' conversion of copper mineral to product have been demonstrated The process can treat low grade and contaminated concentrates without penalty, thereby offering greater returns to the miner. Lead, zinc and silver may be recovered as metals, with the high oxidation potential of the electrolyte allowing extraction of gold at high efficiency. The gold is selectively precipitated on activated carbon with negligible copper and silver contamination.

Jan 1, 1992

By Benjamin F. Tillson

Although portable fire extinguishers are valuable for fires in an incipient stage, some medium that will dissipate a large amount of heat is needed to fight a fire in mine timbers, because of the size to which the fire will probably have grown before it is discovered. Scaling off, or otherwise smothering such a fire with gases that will not support combustion, is often ineffective for the residual heat will cause reignition when the area is opened and fresh air reaches the hot charred timber. The most effective ways of fighting mine fires, therefore, are to drown and cool the hot zone with water, and to "load out" the partly burned material. Either of these methods requires a direct attack of water ; upon the inflamed material; therefore, every mine containing a large ' quantity of timber or other combustible should be as completely equipped with a fire-hydrant system as it is with compressed-air mains. Mine managers may object to the expenditure, especially if they have not suffered from mine fires. The cost of such preventative measures, however, is only a small portion of the possible losses, and the water pipes can be used for other purposes, which will pay the carrying charges. They can supply water to the rock drills, which will encourage more wet drilling with hollow-drill steel, for the trouble and expense of packing water to individual tanks at the drills will be removed. The carbon-tetrachloride hand extinguishers seem to have no place in mining except for fires that start in electrical equipment. They give off noxious gas, which may prove poisonous in confined quarters; and as it is heavier than air it is of no value for smothering fires overhead or in side timbers and would be dissipated by a good ventilating draft. The old soda-acid extinguisher or the more modern "foam" types ' are preferable. The former probably does not rely for its efficacy on the carbon dioxide generated but on the smothering and cooling effect of the water and the trajectory of stream that may be obtained because of the gas pressure developed. The production of a foam having a tough film to smother a fire, even on overhead surfaces, with the added

Jan 1, 1923

By Benjamin F. Tillson

Although portable fire extinguishers are valuable for fires in an incipient stage, some medium that will dissipate a large amount of heat is needed to fight a fire in mine timbers, because of the size to which the fire will probably have grown before it is discovered. Scaling off, or otherwise smothering such a fire with gases that will not support combustion, is often ineffective for the residual heat will cause reignition when the area is opened and fresh air reaches the hot charred timber. The most effective ways of fighting mine fires, therefore, are to drown and cool the hot zone with water, and to "load out" the partly burned material. Either of these methods requires a direct attack of water ; upon the inflamed material; therefore, every mine containing a large ' quantity of timber or other combustible should be as completely equipped with a fire-hydrant system as it is with compressed-air mains. Mine managers may object to the expenditure, especially if they have not suffered from mine fires. The cost of such preventative measures, however, is only a small portion of the possible losses, and the water pipes can be used for other purposes, which will pay the carrying charges. They can supply water to the rock drills, which will encourage more wet drilling with hollow-drill steel, for the trouble and expense of packing water to individual tanks at the drills will be removed. The carbon-tetrachloride hand extinguishers seem to have no place in mining except for fires that start in electrical equipment. They give off noxious gas, which may prove poisonous in confined quarters; and as it is heavier than air it is of no value for smothering fires overhead or in side timbers and would be dissipated by a good ventilating draft. The old soda-acid extinguisher or the more modern "foam" types ' are preferable. The former probably does not rely for its efficacy on the carbon dioxide generated but on the smothering and cooling effect of the water and the trajectory of stream that may be obtained because of the gas pressure developed. The production of a foam having a tough film to smother a fire, even on overhead surfaces, with the added

Jan 1, 1923

By Ali Ekrem Aritan

Exposure to hand-arm vibration (HAV) among the labor force in the mining industry can result in permanent vibration diseases such as behavioral disorders, visual impairment, osteoporosis, pain (mostly in the hands, wrists, and shoulders), circulatory system disorders, and malnutrition. In this study, the vibration exposure of excavator operators working regularly in 25 different natural stone quarries was measured. In addition, the relationship between vibration exposure and rock properties was investigated. Gloved and ungloved vibration measurements were performed and revealed that antivibration gloves reduce excavator operators’ vibration exposure by 7.10–25.95%. Samples from each quarry were characterized with rock mechanics tests. The correlations between the hand-arm vibration measurements and the natural stone physical–mechanical properties (uniaxial compressive strength, Shore hardness, Knoop hardness, apparent density and total porosity) were determined to be over 70%. One finding of the study was that the health risk in excavators cannot be reduced sufficiently by the sole use of antivibration gloves. Furthermore, the excavation of any rock with a Knoop hardness above 121 is associated with an 81% risk of HAV. To increase awareness of the danger of vibration exposure for natural stone miners, training programs should be provided, and technical and operational changes should be implemented.

By Hui-Gai Li

The fine Ti oxide inclusions precipitated during solidification are favorable for intragranular ferrite nucleation. The oxygen content before solidification affects the composition and size of inclusions. The composition of precipitated inclusions in Mn-Ti alloyed steel was studied by means of thermodynamic calculation and experiment in this paper. The micro-segregation of Mn, Ti and O during solidification was considered in calculation and unidirectional solidification apparatus was employed in experiment to ensure that alloy elements diffused along solidification direction. The results showed that: inclusions are mainly Ti oxide when oxygen content is 10ppm; they are Ti oxide and Mn-Ti oxide when it is 20ppm; Mn-Ti oxide dominates when it is 30ppm. With the increase of oxygen content, the size of inclusions increases. The maximum oxides size is about 3µm from statistical results of experiment.

Jan 1, 2008