Search Documents

By T. T. Wang, T. H. Huang, Y. C. Chiu

Quantitatively analyzing deformation of a tunnel with lining anomalies for structural safety evaluation is essential for sustainable tunnel engineering. However, a complete theory and associated methodology accounted for displacement of a built tunnel is absent. This manuscript introduces a novel characteristic matrix method proposed by the authors which is an integrated procedure that analyzes displacement of rock tunnels in operation. First, establish a numerical model expressing a specific state of the tunnel in interest. Derive the characteristic displacement modes by a unit disturbances and check their independency. Once the characteristic displacement modes are proved to be orthogonal (independent), they are ready for use. Given a tunnel displacement, modal decomposition returns the magnitude of each characteristic displacement modes that together consist the given displacement. By realizing the definite value of horizontal and vertical translation, rotation, uniform compression/expansion, elliptic deformation, triangular deformation…etc. for a tunnel displacement, one can distinguish tunnel displacement and deformation types from their modal composition. A circular tunnel with elastic structure and surrounded by elastic rock mass is chosen to demonstrate the outcome of characteristic modes and how they work. The influences of tunnel shape, elastic modulus ratio between rock mass and tunnel structure, and numbers of monitoring points on a tunnel profile were also discussed. Identifying possible tunnel deformation causes is attainable if further connections between mode combination and force increments were built.

Jan 1, 2015

By William M. Phillips

This paper will concern the processing of kaolin clays from the sedimentary deposits of Georgia and South Carolina, While the major processing steps will be touched on briefly, emphasis will be given to the dewatering of the clay-water slurries (slips) formed in the processing of kaolin clays The dewatering steps discussed will include gravity settling, centrifugal dewatering, vacuum filtration, and thermal dryings Of these dewatering steps particular attention will be given to vacuum filtration and the variables affecting filtration of these kaolin clays.

Jan 1, 1962

By S. Arthur Krom

(Wilkes-Barre meeting, June, 1911.) RECENT experiments indicate that the usual type of concentrating-table is not only poorly adapted to produce the desired results, but also is based upon an incorrect principle, namely, the use of riffles to perform the work of stratifying the various minerals. We have heard a good deal about riffles for concentrating-tables; exhaustive experiments have been made to discover the proper form of riffle, or to prove the superiority this or that form; disputes and patent-litigation have arisen over the matter of riffles, and thus many have been led to believe that the riffle is the saving-device upon which the process of concentration depends. In the present paper it is proposed to show that the riffle is greatly overrated as to the part it performs in the concentration of minerals, and that, in the near future, it may possibly be eliminated entirely from that process. The experiments in question have shown that the troublesome riffle can be considered of secondary importance at the most, and should be so classed in the construction of a concentrating-table built upon the right lines. The action of any form of riffle on a concentrating-table is such as to upset and retard the process of settling and stratifying the various minerals on the table-deck. From the deck of a riffled table no concentrates can be delivered until the deck is "bedded," that is, until a sufficient amount of metallic values have been fed to the table to spread over a large portion of the deck, forming a substratum of the heavier minerals. This substratum must be maintained by the feed within quite narrow limits, and directly proportional to the rate of discharge from the table, in order that the bed shall not be lost. On the other hand, the riffles having a very lim-

Jul 1, 1911

Reduce the dust exposure of workers in large processing buildings at mineral processing operations, using a total mill ventilation system.

Jan 1, 1994

By Joseph M. Chelini

The report shows the sensitivity that nine different cash-flow factors have on the discounted rate of return calculated from feasibiliity- studies on potenital open-pit orebodies of silver, copper, and uranium. Cash-flow factors of "grade", "market value", and "recovery" are. the most sensitive. This verifies the need of reliable estimates for these factors. The cost of evaluation of "preproduction cost" is the least sensitive. This gives credence to the fact that more consideration should be given to compiling sufficient data, as the largest financial losses are not in the cost of evaluation but rather in the abandonment of an unprofitable mining operation after a commitment of capital is made on the basis of an incomplete evaluation. Sensitivity analysis of cash-flow factors enhances evaluation programs by disciplining the collection of data and allowing more realistic distribution of evaluation monies.

Jan 1, 1971

By Robert R. Grinstead

Two new ion exchange resins have been developed, which selectively absorb copper and nickel in preference to ferric iron from dilute sulfuric acid solutions of pH 1-3. The first absorbs copper and not nickel and can be readily eluted with 1-2N sulfuric acid. This resin is well adapted to the processing of copper leach liquors, including relatively low grade liquors obtained from dump leaching. The second resin absorbs nickel as well as copper in the same pH region, but only the nickel is eluted with 1-2N sulfuric acid. Elution of the copper requires much stronger (ca. ION) acid, altho both species are readily eluted with dilute (ca. lN) ammonium hydroxide. This resin, which should be useful in processing of certain types of copper-bearing solutions, may also be suitable for treating acidic nickel leach solutions of laterites and other non-sulfide ores.

Jan 1, 1976

The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal. All papers must meet the standards set by the Council of the Institute, and for this purpose all papers are referred to at least two referees appointed by Council. STANDARDS FOR ACCEPTANCE To merit consideration papers should conform to the high standards which have been established for publication over many years. Papers on research should contain matter that is new, interpretations that are novel or of new significance and conclusions that cast a fresh light on old ideas. Descriptive papers should not be a repetition of well-known practices or ideas but should incorporate developments which would be of real interest to technical men and of benefit to the mining and metallurgical Industry. In some cases a well prepared review paper can be of value, and will be considered for publication. All papers and particularly research papers, no matter how technical the subject, should be written with the average reader of the Journal in mind, to ensure wide interest. The amount of textbook material included in a contribution should be the minimum essential to the argument. The length of a paper is not the criterion of its worth and it should be as brief and concise as possible, consistent with the lucid presentation of the subject. Only in very exceptional circumstances should a paper exceed 15 pages of the Journal (15 000 words, if there are no tables or diagrams). Six to ten pages is more normal. NOTE: Papers in the Journal are printed in 10 point type, which is larger than the 8 point type used on this page. For special publications Council may decide on page sizes smaller than A4 used for this Journal. The text should be typewritten, double-spaced, on one side only on A4 size paper, leaving a left-hand margin of 4 cm, and should be submitted in duplicate to facilitate the work of the referees and editors. LAYOUT AND STYLE Orthodox sequence Title and author's name, with author's degrees, titles, position. Synopsis. Index, only if paper is long and involved. Introduction, including a brief statement of conclusions. Development of the main substance. Conclusions. in more detail. Acknowledgements. References. Title: This should be as brief as possible, yet give a good idea of the subject and character of the paper. Style: Writing should conform to certain prescribed standards. The Institute is guided in its requirements by: Collins, F. H., Authors & Printers' Dictionary-Oxford University Press. Hart, H. Rules for Compositors and Readers. Humphrey Milford (familiarly known as the Oxford Rules). Fowler, H. W. & F. G. The King's English-Oxford University Press. General: A few well selected diagrams and illustrations are often more pertinent that an amorphous mass of text. Over-statement and dogmatism are jarring and have no place in technical writing. Avoid the use of the first person, be objective and do not include irrelevant or extraneous matter. Avoid unnecessary use of capitals and hyphens, while punctuation should be used sparingly and be governed by the needs of sense and diction. Sentences should be short, uninvolved and unambiguous. Paragraphs should also be short and serve to separate basic ideas into compact groups. Quotation marks should be of the 'single' type for quotations and "double" for quoted matter within quotations. Interpretations in the text should be marked off by parentheses ( ), whereas brackets [ ] are employed to enclose explanatory matter in the text. Words to be printed in italics should be underlined singly. For small capitals they are to be underlined DOUBLY and for large capitals TREBLY. If there is any problem in producing formulae accurately by typewriter they should be inserted by handwriting in ink in the copy forwarded by authors. Abbreviations and symbols are laid down in British Standard 1991. Abbreviations are the same for the singular and plural, e.g. cm for centimetre and centimetres, kg for kilogram and kilograms. Percentages are written in the text as per cent; the symbol % is restricted to tables. A full stop after an abbreviation is only used if there is likely to be confusion of meaning. Metric System: The Systeme International d'Unites (S.I.) is to be used for expressing quantities. This is a coherent system of metric units derived from six basic units (metre, kilogramme, second, ampere, kelvin, and candela), from which are derived all other units, e.g. the unit of force is the newton (N) for kilogramme metre per second per second (kg m/s2). Always use the standard metric abbreviations. Commas must not be used for separating groups of digits. For ease of reading digits should be grouped in threes counting from the decimal point towards the left and the right. Illustrations: Drawings and diagrams are to be in black India ink and should be about 18 cm wide. When submitting graphical representations avoid a fine grid if possible. Curves should be in heavy line to stand out. Lettering too should be bold as a reduction in size is often involved in the printing process. (A single column is 8.5 cm wide.) Numbering of tables should be in Roman numerals: I, 11, etc. and figures in Arabic numerals: Fig. 1, Fig. 2, etc. (Always use the abbreviation for figure.) Photographs should be black and white glossy prints. As a guide to the printer the author should indicate by means of notes in the typescript where tables and figures, etc. are to appear in the text. Paragraphs: A decimal system of numbering paragraphs may be used when the paper is long and complicated and there is a need for frequent reference to other parts of the paper. Proof correction: Galley proofs are sent to authors for the correction of printers' errors and not for the purpose of making alterations and additions which may be expensive. Should an author make alterations which are considered excessive, he may be required to pay for them. Standard symbols as laid down in British Standard 1219C should be used. SYNOPSIS It is most important that the synopsis should provide a clear outline of the contents of the paper, the results obtained and the author's conclusions. It should be written concisely and in normal rather than abbreviated English and should not exceed 250 words. While the emphasis is on brevity this should not be laboured to the extent of leaving out important matter or impairing intelligibility. Summaries simplify the task of abstractors and therefore should present a balanced and complete picture. It is preferable to use standard rather than proprietary terms. FOOTNOTES AND REFERENCES Footnotes should be used only when they are indispensable. In the typescript they should appear immediately below the line to which they refer and not at the foot of the page. References should be indicated by super-script, thus. . .1 . . .2. Do not use the word Bibliography. When authors cite publications of other societies or technical and trade journals, titles should be abbreviated in accordance with the standards adopted by this Journal. GENERAL The Council will consider the publicatiol1 of technical notes taking up to three pages (maximum 3000 words). Written contributions are invited to the discussion of all papers published in the Journal. The editors, however, are empowered by the Council to edit all contributions. Once a paper or a note has been submitted to the Institute, that document becomes the property of the Institute, which then holds the copyright when it is published. The Institute asa body is, however, not responsible for the statements made or opinions expressed in any of its publications. Reproduction from the Journal is permitted provided there is full acknowledgement of the source. These points should be borne in mind by authors who may submit their work to other organizations as well as to the Institute. P.W.J.vR.

By K. Deaton

"INTRODUCTION A packaged cooling system is being developed for refuge alternatives (RAs) that meets MSHA qualification guidelines for deployment in coal mines. This system will allow full occupancy ratings of deployed Refuge Alternatives (RAs) to be maintained by keeping the apparent temperature inside the RA from exceeding 95°F. Research investigations sponsored by NIOSH have shown that heat buildup caused by occupants in mobile RAs will result in apparent temperatures that exceed the 95°F limit established in 30 CFR 7.504. Figure 1 shows the temperature rise in an inflatable RA having an occupancy rating of 23 people at an 81°F mine air temperature. This plot shows the need for either heat mitigation or occupancy derating in warmer mines. The RAECS will be designed to provide enough heat mitigation to eliminate occupancy derating due to heat buildup over the 96 hour refuge period.This paper describes testing of a prototype cooling system that uses proven vapor compression technology powered by batteries to keep the RA interior below the 95° limit for a minimum of 96 hours. Testing of this prototype cooling system was conducted in December of 2015 and January of 2016 at the NIOSH test mine in Bruceton, PA. December testing was conducted at the prevailing mine ambient temperature – approximately 60°F. The January testing was done with the mine ambient temperature in the immediate vicinity of the RA artificially elevated to 85°F. Realistic heat gain from RA occupants was provided by human simulators developed by NIOSH. These simulators add sensible heat corresponding to human metabolic processes and latent heat generated by respiration and perspiration. Heat generated by CO2 scrubbers was also added. Results of cooling system performance using these simulated loads at the two ambient conditions are described. A comparison of the apparent temperature in the RA using two different control techniques is also presented. This work documents the ability of the cooling system to meet the established apparent temperature limit at the full occupancy rating of a six person RA. A new cooling system intended for use with existing RA deployments and having greater cooling capacity is currently in development and will be described."

Jan 1, 2017

By C. L. Brown

"INTRODUCTION The heavy loss of life from mine fires in some coal mines recently has focused attention on the importance of maintaining reliable communication systems between the active working sections of mines and the surface. A study of conditions following disasters in mines indicates that in several instances lives could have been saved if telephone communication had been available. Communication systems were not installed in some of these mines where disasters occurred, and in other mines they were installed in such a manner as to be rendered useless following a mine explosion or fire. Lives have been lost because of the inability of the rescue crews or persons di-recting the rescue to communicate with trapped men. Cases are known where many lives might have been saved had it been possible to give instructions for escaping or for location of barricades.More than 500 major disasters in which 5 or more lives have been lost have occurred in mines in the United States. The total number of lives lost in these disasters has exceeded 13,000. Some of the victims died instantly; but for many it was hours and in some instances days before death occurred. Evidence found in recovery operations following some of the disasters indi¬cates that many died needlessly because of the lack of suitable means of communication between the underground working areas and the surface.A localized gas and dust explosion in a coal mine in 1930 resulted in the death of 82 men; 2 were killed outright by the force of the explosion, 6 by a combination of burns and afterdamp, and 74 by afterdamp. About 140 men escaped or were rescued following the explosion, Of these, 119 escaped with little or no assistance, 2 were rescued promptly following the explosion, and 19 were rescued from behind a barricade. Seven bodies were re-covered from behind an ineffective barricade in another place; subsequent investigation proved that these men might have been guided to a safe location had an effective communication system been available."

Oct 1, 1946

This chapter presents an overview of fatal and nonfatal injuries reported to MSHA during 1986-1995. Reportable injuries follow the criteria for reporting specified in 30 CFR 50. These criteria are listed in appendix A. The data used for these analyses came from the MSHA accident, injury, and illness data closeout files for the years 1986-1995. The MSHA data are described in appendix A and methods used in data analysis in appendix B. There may be slight discrepancies between the figures presented here and other presentations of MSHA data for the following reasons: (1) injuries to nonemployees have been excluded from analysis; and (2) injuries identified by MSHA after the files were closed out are not included. Within the MSHA data, there are differences in reporting requirements for operators and contractors. Contractors are required to report only those injuries that occur during certain categories of work (described in appendix A). For this reason, data on injuries among employees of operators and contractors in the MSHA database should not be considered directly comparable. As discussed in the "Introduction," the MSHA data on fatal injuries differ from the CFOI data (chapter 1) because of varying definitions used for the mining industry. As compared to the CFOI data, MSHA data exclude injuries that occurred off of mine property and include injuries occurring at mills and processing plants on mine property. Tables 4-1 through 4-9 and figure 4-1 provide comparisons of injury frequencies and rates among the commodities. These comparisons are followed by sections 4A through 4E, which provide more detailed tables and figures for each commodity separately. The method used to calculate injury rates is described in appendix B. Since denominator data for occupations (lob titles) were available for 1986 only, estimates of rates by occupation for the entire 10 year period are based on extrapolation from 1986 data. For this reason, estimates of injury by occupation should be interpreted with caution. Fatal Injuries A total of 1,078 fatal on-the-job injuries were reported to MSHA during the 10-year period 1986- 1995. The average annual fatal injury rate for all commodities combined during this period was 30.9 per 100,000 full-time equivalent workers. Mine operators accounted for 908 (84%) of the fatalities and had an average annual fatal injury rate of 28.2 per 100,000. While mine contractors comprised only 16% (n = 170) of the total number of fatalities, their average annual fatal injury rate was 2.3 times higher than that of mine operators (65.0 per 100,000). Table 4-1 presents the number and rates of fatal injuries by commodity for operators and contractors. Contractors in metal, nonmetal, stone, and sand and gravel are grouped together, since MSHA data on employment were not available for rate calculations for these commodities separately. The highest average annual fatality rate for the period, 66.5 per 100,000, occurred among metal and nonmetallic mineral mining contractors, followed closely by coal contractors (63.1 per 100,000). Among mine operators, the highest average annual fatal injury rate was in coal (38.9 per 100,000); the lowest was in nonmetal (14.3 per 100,000). Table 4-2 shows the average annual fatal injury rate by type of operation for each commodity for mine operators only. Of commodities with underground mines, all except stone had higher fatality rates at underground than at surface operations of these mines. The highest fatality rate for any operation occurred in surface operations at underground stone mines (124.5 fatal injuries per 100,000 workers). Stone had the second highest fatality rate for underground operations at underground mines (77.9 per 100,000). The highest rate for underground operations at underground mines occurred in metal (87.6 per 100,000). Table 4-3 shows the number and rate of fatal injuries by U.S. Bureau of the Census occupational groups (described in appendix D) for the 10 occupation-commodity groups with the highest fatal injury rates. These data should be interpreted with caution because the denominator used in calculating the rates was based on an extrapolation from data for the year 1986 only, as described in appendix B. Extractive occupations are represented in this group for three commodities: coal, metal, and sand and gravel. Construction trades are included for coal, sand and gravel, and nonmetal. The distribution of fatal injuries by commodity and work activity for mine operators is presented in table 4-4. A description of the work activity categories is in appendix C. Overall, the leading work activity at the time of injury was using or operating tools and machinery (26.4%) followed by constructing, repairing, and cleaning (24.0%), vehicular operations (18.8%), and materials handling (12.6%). The distribution varied by commodity. The largest percentage of fatal injuries occurred while operating tools and machinery in both coal and stone; during vehicular operations in metal; and during constructing, repairing, and cleaning activities in nonmetal and sand and gravel. Table 4-5 shows the distribution of fatal injuries by commodity and MSHA accident classification for mine operators. A description of the MSHA accident classifications appears in appendix E. The largest proportion of injuries overall occurred during powered haulage (28.5%). The

Jan 5, 2000

By Tetsuya Yumoto, Toshikazu Shiratori

Information on the elements contained in E-Waste is important from the viewpoint of recycling. We analyzed several components of waste electrical and electronic equipment (WEEE) collected from citizens. The distributions of the minor metals in WEEE were determined with elemental mapping and chemical analyses. The annual change in elemental composition was investigated by analyzing equipment manufactured in different years. The information will be of use for separation techniques required for future advanced recycling.

Jan 1, 2011

By Rameshwar Sah, PK GHORUI, LR SINGH, SIVALINGARAJU BARISETTY, SHYAM YADAV

Fly ash is a by-product generated by the combustion of coal in thermal power plants. Its disposal is a major environmental concern for these power plants. Though a considerable part of fly ash is used in cement making and brick manufacturing, a substantial quantity remains unutilized. Bentonite is commonly used as binder in the micropelletization of process waste to attain the mechanical strength required for handling and transportation. The present paper deals with the partial replacement of bentonite with fly ash in the micropelletization process without affecting the quality of the micropellets. The mechanisms of both the binders are discussed. The bonding of particles by bentonite is a physical mechanism, while fly-ash bonding is a chemical mechanism. Silica and alumina are the major constituents present in fly ash along with lime. In the presence of water, the alumino-silicates and unhydrated lime present in fly ash undergo a pozzolanic reaction and form cementitious bonds, which hold the particles together. Use of fly ash as alternative binder for bentonite has cost benefits besides providing a better utilization option for fly ash.

By R Frank' Mammele Chiappetta, Conny Postupack

A major problem that has continued to plague the surface coal industry is blast induced damage to the coal seam. Atlas Powder Company has addressed this situation through seven years of field research in full-scale production environments. Many operations across the United States have been evaluated.

Jan 1, 1988

By Thomas R. Wildeman

Experimental methods for studying vapors over solid minerals are reviewed and an especially developed method using atomic absorption is described. The method is used to study vapor pressures over Te. Ag, Au, Ag2Te, and AuTe2 from 250°C through 10S0oe. Vapor pressures observed and, concurrently. sintering properties are significantly altered by the form of the solid. The vapor pressures of the tellurium compounds reveal complex processes occurring on the surfaces of the solids. The data given also point out a method of recovering precious metals from their telluride minerals w

Jan 1, 1987

By Sabine Verryn, Johan de Villiers

"Through the application of the Rietveld method, X-ray diffraction analysis has developed into a fully quantitative method for phase analysis. The Rietveld method itself has progressed from an unstable method that required constant operator intervention to a stable and robust method suited even for routine analysis. The method however, requires a good initial calibration and periodic checks on its precision and accuracy.Several examples from minerals processing, pyrometallurgy, and materials science show the strengths and applicability of the method. The limitations and sources of error are also discussed.1. IntroductionDiffraction of X-rays by matter has been used for more than 80 years, initially to elucidate the structure of crystalline matter, and to investigate the bonding between atoms. The first development of powder diffraction cameras and the later development of X-ray diffractometers saw the development of methods to identify phases and to try to quantify them in mixtures. A comprehensive database and search-match techniques have been developed over the ensuing years. Effective and accurate quantification had to wait for the so-called Rietveld' analysis where the total diffraction pattern is used and where the crystal structure data for the constituent phases are needed as input. Overlapping of diffraction peaks of different phases is handled without difficulty and reliable results can be obtained in spite of this occurrence.The development of methods for structure analysis from powder data has also progressed rapidly and more and more complex structures are being solved from first principles, i.e. without knowledge of unit cell or space group data. Because of the ease of use of the Rietveld method, it is finding increased application in metallurgy, especially in the quantification of phases of importance in minerals processing, in pyrometallurgical processes, and in materials characterization. This study will examine the principles of the Rietveld method, its application in metallurgy, and finally also the common pitfalls that need to be avoided.2. Rietve1d AnalysisAs the Rietveld method compares the experimental diffraction pattern with one calculated from known crystal structure data, the following data are needed:•,An XRD Pattern with as Iowa background as possible. This should have good resolution and high diffraction peak intensities. With modem X-ray detectors, this can be achieved in minutes rather than hours.•,Instrumental parameters such as goniometer radii and slit sizes are needed. These are the so-called ""Fundamental parameters"". They are used to calculate the shapes of the resultant diffraction peak profiles that are caused by the instrument. The parameters are used to correctly separate the instrumental effects on the diffraction pattern from the sample effects."

Jan 1, 2014

By J. Baumbach, H. Bombach, M. Stelter

"Today technical electro-refining processes for copper exclusively use sulfuric acid, for silver refining nitric acid electrolytes are used. Sulfuric acid is characterized by very good chemical and electrochemical stability, good conductivity and low cost. The disadvantages of sulfuric acid are the precipitation of fine-grained cathodes with smooth surfaces only by using additives like glue, thiourea and chloride. In case of silver the electrolyte is electrochemical unstable and bears the risk of the formation of toxic NOx when pH is too low. A second disadvantage is the form of electrodeposition of silver as dendrites with their removal from the bottom of the Möbius cells.This paper reports the results concerning the application of an alternative electrolyte in copper and silver electro-refining. At first the electrolyte was characterized by the determination of current density potential curves. Electrolysis experiments were performed in laboratory scale using technical anodes for copper and synthetic anodes for silver. During the copper tests the solubility of contaminations from the anodes and the amount and chemical composition of the anode slimes were determined. Moreover the influence of current density, electrolyte temperature and the effect of several additives on the precipitation and chemical purity of the cathodes were investigated. In all experiments cell voltage as well as anodic and cathodic polarization was measured and current efficiency and specific energy consumption were calculated. A comparison with the results with those of tests using conventional sulfuric acid electrolyte shows the advantages and disadvantages of both systems, additionally the technical application chances and limitations for the new electrolyte. This electrolyte enables the precipitation of smooth copper cathodes with low silver and sulfur concentrations even at lower temperatures without any additive. For silver refining the electrodeposition of compact silver sheets is possible, that can be stripped comparable to those in copper electro-refining."

Jan 1, 2016

By James J. Fallen

In this paper we are going to look at some things that may happen to the industrial minerals industry in the next decade. First, some concepts and definitions. What are industrial minerals? Not everyone agrees on an answer to this. So let's look at some of the opinions. Some say that industrial minerals are non-metallic minerals. As you well know, metallic minerals are used as a source material for metals. Copper, lead, and zinc are extracted from metallic minerals. But, some metallic minerals are also used for other reasons. Bauxite is used as a source of alumina and aluminum. It is also used as proppant in well drilling, as an abrasive, as a refractory material, and as a source of aluminum-based chemicals. So bauxite is both metallic and nonmetallic. There are other examples, too. Bastnasite is a source of rare earth metals and alloys but its concentrate is used in fluid cracking catalysts. Phosphate rock is an industrial mineral when used for fertilizer, but it is also the source of phosphorus. Ilmenite and rutile are sources for titanium dioxide pigments as well as titanium. So the nonmetallic designation is not adequate to define industrial minerals. Some say industrial minerals are called such because they are consumed in industry. How about your cat's litter box? Is that industry? Huge amounts of montmorillonite, attapulgite and other sorbtive minerals are pelletized and calcined to make animal litter. Doctors are trying to get people to cut down on their salt consumption. They are against people eating industrial minerals. When diamonds are a girl's best friend, they are not industrial minerals; when they are grinding and polishing media, they are. These examples show that industrial minerals are not exclusive to industry. Regardless, here is my list of industrial minerals: Abrasive Materials - Bentonite Antimony (Oxide) - Borates Asbestos - Calcium Carbonate Attapulgite - Diatomite Ball Clay - Dolomite Barite - Feldspar Bauxite (and Alumina) - Fire Clay Fluorspar - Pyrophyllite Fuller's Earth - Rare Earths Graphite - Salt Gypsum - Sand and Gravel Kaolin - Silica Sand Kyanite - Soda Ash Limestone - Sodium Sulfate Magnesite - Spodumene (Lithium) Magnetite - Sulfur Mica - Talc Nepheline Syenite - Titanium Dioxide Perlite - Vermiculite Phosphates - Wollastonite Potash - Zeolites Pumice There is some overlapping. Fuller's Earth takes in some attapulgite, bentonite, and other minerals, depending on the market. Some would like to distinguish industrial minerals by the market emphasis they receive compared to fuels, metallics, and precious metals. But even there, strict logic fails. Some industrial minerals are commodities. They are sold on a price basis against industry product specs, usually in large volumes. Phosphate rock, potash, sulfur, salt, soda ash, and other materials fit this category. Some are almost custom-designed for end-use and meet performance specs. These are sometimes called functional or specialty industrial minerals. Examples of these are ground calcium carbonate, water-washed kaolin, cosmetic grade talc, filtration grades of diatomite, perlite, and vermiculite. To determine prospects for the decade ahead, regardless of our

Jan 8, 1984

By D. K. Sengupta

Increased recycling of waste paper has been emphasized in recent years in both the USA and Canada for environmental and economic reasons. Removal of ink particles from the waste paper pulp is therefore necessary. One of the most promising methods for ink removal is froth flotation. Our study investigated the feasibility of a simplified flotation scheme which showed that about 90-92% ink removal can be achieved while 95-97% ink removal is achievable if a hydrophobic polymer is used ahead of flotation. The clean paper pulp recovery was over 90%. The effects of pulping pH, flotation pH, and concentrations of flotation and polymeric reagents are discussed in the paper.

Jan 1, 1993

By C. A. Rowland

Autogenous grinding, defined as grinding with like material, while quite an old art has recently been revitalized. Two phases of autogenous grinding, primary and secondary, have been the subject of recent papers, technical articles and discussions. The purpose of this paper is to discuss a third phase of autogenous grinding - Intermediate Autogenous Grinding - comparing it to and indicating advantages over the other two phases. Autogenous grinding can also be called ?Rock grinding?1; that is, grinding using ore or rock from the same deposit as the mill feed as grinding media contrasted with using as grinding media steel rods, steel or ironballs, natural or manufactured iron, free pebbles, or other shapes and materials foreign to the mill feed.

Jan 1, 1964

By M. D. Quinn

THE sand and gravel used for backfilling at the Hollinger mine is obtained from deposits in a low range of hills some three miles north of the mine, where the Company owns a number of claims. The material is transported to the mine by aerial tram. Shipments from these deposits to the Hollinger mine commenced in June, 1927, and since May, 1936, sand has been supplied also to the McIntyre mine. During 1942, Hollinger requirements were 1,700 tons per day, and 900 tons per day was delivered to McIntyre. For the past seven years production has averaged 900,000 tons annually, and total deliveries to the end of 1942 were 13,129,022 tons, of which 11,075,339 tons went to Hollinger and 2,053,683 tons to McIntyre. Some years ago, when the original pit was approaching exhaustion, new workings were opened on claims east and south of the tramway terminal. It soon became apparent that the sand varies considerably in character from place to place. The weight per cubic foot was found to range from 85 to 130 lb., and the water percolation rate from 2 to 50 inches per hour. As the mine requirement is a sand with percolation rate of 6 inches or better per hour, it was evident that in certain parts of the deposits the material was not suitable for use as backfill. As a consequence, it was decided to carry out a programme of systematic sampling of the claims in order to select the areas containing suitable material for back-fill and at the same time estimate the tonnage available.

Jan 1, 1944