Search Documents

By Florian Kongoli

"Lime ferrite" slag with limited silica content has proven to be a valuable choice in the modem processes of copper smelting and converting due to several advantages that this slag offers compared to classical silicate slags. Nevertheless the liquidus surface of this slag has been experimentally measured only at low oxygen potentials such as in equilibrium with iron or hear it and in air. Although most of the smelting and converting processes that use this slag occur at intermediate oxygen potentials, the liquidus surface of this slag is not known at these conditions and the effect of oxygen potential and silica has not been correctly understood. This has brought some confusion in literature as well as in the industrial practice. In this work the liquidus surface of the calcium ferrite slags has been quantified by the means of a new thermophysicochemical model and a new type of liquidus surface diagrams which are very convenient for any industrial process that uses calcium ferrite slags. These diagrams can be easily used to select the lowest liquidus temperature of calcium ferrite slags at a minimum cost and can help design several fluxing strategies in copper smelting and converting processes. The effect of the oxygen potential and silica is also quantified and important industrially related conclusions are drawn.

Jan 1, 2003

By Dennis R. Dolinar, Jeff Dubbert, Hamid Maleki

The advance-and-relieve method benefits from lateral destressing associated with mining in laminated rocks and a high horizontal stress regime. This stress control method is based on measurements showing that occurrence of rock failure in the roof and floor of an entry (or caving of roof strata in a panel gob) results in redistribution of stresses in adjacent entries. By locating other entries within the shadow zone of the first entry (or gob), improvements in stability can be achieved. Numerical modeling proved useful in studying the basic mechanics of lateral relief while investigating the sensitivity of results to different geologic and mining parameters using controlled experiments. It was shown that failure of rocks near an entry results in redistribution of horizontal stress and shifting of the stress to higher horizons. Measurements from two mines are consistent in showing significant horizontal stress reductions in comparison with the far-field stress regime within the destressed zone. Although the far-field stress regime is very anisotropic, these measurements show near-equal secondary principal horizontal stresses, or perhaps a switch in orientation, as a result of destressing. Stress relief is achieved through lateral movement and relaxation of rocks along weak bedding planes toward adjacent caved zones (or softened zone). Because of cave geometry in the advancing panel, horizontal stress concentrations occur near the cave line both in front of the face and to the sides. The horizontal stress concentration reaches 1.7 times the far-field stress ahead of the face. This stress increase is significant and may cause structural damage in this zone benefiting from additional support. In the next advancing panel located within the shadow zone of the gob, horizontal stresses are significantly reduced in the roof (by 50%). Thus, the stability of future advancing panel can be improved through prudent layout designs and sequencing. The width of the relief zone is significantly influenced by the height of the softened (or cave zone) and rock mass properties.

By Pedro Henrique L. M. Lopes, Édio Pereira Lima Jr., Fernanda Santos da Luz, Fábio de Oliveira Braga, Sergio Neves Monteiro

Several works have been dedicated to study the ballistic response of multilayered armor systems (MAS), including those using natural fiber composites as second layer. These composites disclosed good ballistic performance, having economic and environmental advantages. In the present work, the objective was to investigate the effect of areal densities of each MAS layer, in the overall performance of a MAS with an alumina ceramic front, a curaua fabric reinforced composite filling, and an aluminum alloy backing the target. Ballistic “backface signature” tests were conducted, varying the areal densities of the MAS layers according to a Box-Behnken design. The results showed a similar influence of the ceramic and aluminum layers in the MAS “backface signatures”, although deformation and failure mechanisms were significantly different. The composite also showed significant participation in the overall MAS performance. Since the composite is cheaper and lighter, a balance minimizing the other layers would be advantageous.

Mar 1, 2018

By Charles E. Wait

In the use of the apparatus purchased for the new chemical laboratories of the university, no piece has given us more satisfaction, or has been a greater success, than a new still which is the subject of this paper. In the designing of this still I had two definite objects in view ; one, the utilizing of steam from the large 60 horse-power boiler used in heating the building, and the other, a provision for making distilled water with gas, when steam from the heating-plant was not available. The still is encased in wrought-iron, with a lining of asbestos, and is provided with a float which automatically regulates the flow of water from the supply-pipe. It was made for me by G. J. M?rrle, Pforzheim, Germany, and was imported by Messrs. Eimer & Amend, of New York City. It is a beautiful piece of apparatus, and the workmanship is excellent in every detail. The essential parts of this apparatus will be understood by consulting the accompanying figures, but a few words of explanation may be appropriate. The still has a capacity of seven gallons, and is made of heavy copper, tin-lined. It has a water-gauge showing the height of the water in the still, also an exit for steam, and safetyvalve, V; inlet for steam through a coiled perforated block-tin pipe; also an outlet, 0, for cleaning out the still; and there is also a heavy

Jan 1, 1895

By C. E. Lundin

The Ce-H system was investigated in the temperature range, 573° to 1023°K, and the pressure range, 10-3 to 630 Torr, as a function of 'composition up to 72 at. pct H. Families of isothermal arid isopleth curves were plotted from the pressure-terr~perature-composition relationships. From these curves the solubility relationships were determined for the system. The isopleths are analytically represented by equilibrium dissociation pressure equations. The relative partial molal enthalpzes and entropies of solution of hydvogen in the systerrz were calculated fronz the dissociation pressure equulions and are tabulated. The integral free energies, enthalpies, and entropies of mixing in the Ce-H system were determined from the relative partial quantities and are also tabulated. The standard free energy, enthelpy, and entvopy of reaction of the dihydride phase at kcal per kcal per mole H2, and ?S° = -34. 1 cal per deg mole H2, respectively. The equilibrium dissociation pressure equation in the two-phase region is: UNTIL recently very little was known of the detailed solubility and thermodynamic relationships of the Ce-H system. Two previous investigations1,2 are noteworthy. However, significant discrepancies and omissions exist on analyzing them. The work of Mulford and Holley1 on cerium did not clearly delineate the boundaries of the two-phase region, Cess - CeH2-x. The plateau partial pressures were not thoroughly defined and were considerably displaced in pressure compared to those from the work of Warf and Korst.2 These latter authors concentrated their studies primarily from 823° to 1023°K in the pressure range of 1 to 760 Torr. No data were determined to outline the regions of primary solid solubility and the hydride phase. Also the establishment of the plateau partial pressures was rather limited in scope. In neither work was a treatment conducted of the relative partial molal enthalpies and entropies of solution of hydrogen in the single-phase regions and the integral thermodynamic quantities of mixing throughout the system. Therefore, it was the objective of this research to determine the complete equilibrium solubility relationships and thermodynamic data for the system by pressure-temperature-composition studies. EXPERIMENTAL PROCEDURE The cerium metal for this study was donated by the Reno Metallurgy Research Center of the Bureau of Mines. Total impurity content was 0.13 pct with only 60 ppm O. The metal was checked metallographically and contained only minor amounts of second phase compared to cerium from other sources. Specimen preparation was done in a dry box flushed with argon gas. The surface of a small rectangular piece of cerium (about 0.2 g) was filed with a clean, mill file. Final weighing was done in a tared enclosed vial containing argon gas. The specimen was then loaded quickly into the reaction chamber which was purged several times with high-purity hydrogen gas and then allowed to pump to about 10-6 Torr. The furnace was heated to the reaction temperature and the run started. The equipment used to conduct the hydriding was a Sievert's-type apparatus. Basically it consisted of a source for pure hydrogen, a precision gas-measuring burette, a heated reaction chamber, a McLeod gage, and a mercury manometer. Pure hydrogen was supplied by the thermal decomposition of uranium hydride. The 100-ml precision gas burette was graduated to 0.1-ml divisions and was used to measure the quantity of gas and admit it to the chamber. The reaction chamber was a quartz tube. Prior to each run, the cerium specimen was wrapped in a tungsten foil capsule to prevent reaction of the cerium with the quartz. Control of the temperature was achieved within ±1°K. Pressures in the manometer range were measured to ±0.5 Torr and in the McLeod range (10-3 to 5 Torr) to ±3 pct. The compositions of hydrogen in cerium were calculated in terms of hydrogen to cerium atomic ratio. These compositions were estimated to be ±0.01 H/Ce ratio. The technique used to study the equilibrium pressure-temperature-composition relationships of the Ce-H system was to develop experimentally a family of isothermal curves of composition vs pressure. The range of pressure through which each isotherm was developed was from 10-9 to about 630 Torr in the temperature interval, 573° to 1023°K. RESULTS AND DISCUSSION The hydriding characteristics of cerium are iso-morphous with those of the elements of the light-rare-earth group (lanthanum, cerium, praseodymium, and neodymium) wherein the region from the dihydride to trihydride is continuously single phase.' The structure of this phase is fcc.3 The heavy rare earths form a trihydride,2 which is hcp, separated by a two-phase region from the fcc dihydride phase. The Ce-H system is represented by the family of experimental isotherms in Fig. 1. Due to the small scale required to draw the curves, the experimental points are omitted; however, a total of 240 experimental data points were taken to prepare these curves. The solubility relationships can be deduced therefrom. Three distinct regions of partial pressure and composition can be seen. The region of cerium solid solution is represented by the rapidly rising isotherms in the dilute composition range. In accordance with Gibbs Phase Rule only one solid phase, the cerium solid so-

Jan 1, 1967

By D N. B Skinner, R L. Brathwaite, M S. Rattenbury

The Institute of Geological and Nuclear Sciences Ltd has carried out a mineral resource assessment of the Coromandel region, one of the most mineral-rich regions of New Zealand. The assessment focussed on metallic minerals and clays, because these are the main commodities that have potential for increased production and export from the region (and from New Zealand).   Three steps were used in the assessment: 1) development of mineral deposit models, 2) comparison of the models with regional geology, structure, geochemistry and past mineral production to estimate the number of undiscovered mineral deposits, and 3) application of grade-tonnage models to determine the quantity and value of the known and undiscovered resources. In step 1, descriptive and grade-tonnage mineral deposit models were developed for 11 different types of mineral deposits: ò     Low-sulphidation andesite-hosted epithermal Au-Ag ò     Low-sulphidation rhyolite-hosted epithermal Au-Ag ò     High-sulphidation quartz-alunite epithermal Au ò     Porphyry Cu-Au-Mo ò     Andesite-hosted polymetallic veins adjacent to mineralised porphyry stocks ò     Zn-Pb-Ag skarn ò     Cu-Ag skarn ò     Hot spring Hg ò     Shoreline placer Ti ò     Rhyolite-hosted halloysite clay ò     Volcanic-related kaolinite clay   Step 2 was aided by a geographic information system (GIS) assembled from a number of digital spatial data sets including: a digital elevation model, an aeromagnetic map (from open file mining company data), a geological map (from the GNS QMAP project), location of areas of hydrothermal alteration, locations of mineral deposits (from the GERM database), stream sediment geochemical analyses (from the REGCHEM database), and a lineament map derived from satellite remote sensing data and the digital elevation model.   Based on May 2001 commodity prices, potential resources estimated for the 11 mineral deposit and grade-tonnage models total NZ$22 806 million for the metallic minerals, NZ$1000 million for halloysite clay deposits and NZ$57 million for kaolinite clay deposits.

Jan 1, 2001

By Michael Perlow Jr

A modification of the original Davisson Offset Limit (DOL) is presented for drilled foundations using soil quake (QDOL) factors ranging from 2 to 6. A further modification of the Davisson Offset Limit has also been developed using helical pile soil quake values (HDOL) based upon helix diameter. In addition, the initial tangent slope (IS) of the pile load test displacement curve is used in lieu of the calculated elastic slope (ES) to eliminate many of the uncertainties associated with determining the drilled foundation pile elastic modulus. The QDOL and HDOL load test methods do not require any graphical interpolation and provide easy simple ultimate pile capacity interpretation methods where drilled foundation pile load tests are not carried to plunging failure. Drilled foundation and helical pile load test case studies are presented to demonstrate the use of the modified soil quake QDOL and HDOL Methods.

By Donald Leroux, Martin Suichies, Andy Trusiak, Chris Dechert

"In modem concentrators, the operation of flotation machines is often stabilized by simple control loops. Froth level, slurry density and aeration rate are all physical parameters typically controlled through classical PID loops. Few concentrators, however make use of advanced computing technologies for controlling the grade of flotation product streams. Technical challenges such as long process delay and the long and uneven sampling interval of on-stream XRF analyzers often restrain their implementation. Model Predictive Control (MPC) is known to have better performance than PID for controlling processes with long delays (such as flotation circuits). This paper describes the implementation of a multi-input/single-output (MISO) MPC algorithm and an FIR model identification routine using an object-oriented graphical computing environment.The MPC module (controller and identification) was implemented on an industrial control system and applied to many sulfide flotation circuits in the Brunswick Mining concentrator (New Brunswick, Canada). In most cases, the manipulated variable was the collector addition. As long as it is provided with decent process models, the performance of the MPC controller is good on all the flotation circuits on which it was applied. Significant reductions of grade variance are reported and the controller responds well to set-point changes. The user-friendly, graphical nature of the computing environment led to a high degree of acceptance by both the process engineers and the flotation operators.1. INTRODUCTIONOver the past three decades, much instrumentation has been developed for flotation machines. The introduction of instruments such as pulp density gauges and cell level probes was particularly well received by the plants where pneumatic and electronic controllers were available for implementing PID control loops. In a way, these simple loops revolutionized the mineral industry. The operation of flotation circuits could then be stabilized through the use of automatic controllers."

Jan 1, 1999

By J. L. Lamon, W. Crafts

Study with the electron microscope of the carbides in vanadium-chromium-molybdenum steels after tempering up to 1000 hr at 600 teelsto 1400°F confirmed that alloy carbides are formed at the secondary hardening temperature by decomposition of the plate-like iron carbides. It was also demonstrated that vanadium carbide persists as much smaller particles than do chromium- or molybdenum-bearing carbides. Conditions conducive to the formation of fine vanadium carbides are indicated to be favorable for high temperature strength. IN order to determine the effects of long exposure at high temperatures on vanadium-bearing steels, a survey has been made of their hardness and carbide structure. The behavior of carbides in the tempering of martensite was studied by X ray diffraction and electron microscope examination of electrolytically extracted residues in greater detail than in an earlier investigation.' A group of steels with about 0.25 pct carbon and containing chromium up to 5 pct, molybdenum up to 1 pct, and vanadium up to 1 pct was either quenched or annealed and then tempered for peri- ods of up to 1000 hr at 600° to 1400°F. Their hardness after tempering agreed with the Hollomon and Jaffe2 relation of equivalency of time and temperature, and with the degree of secondary hardening predicted from composition. Further, the appearance of the carbides indicated that the time and temperature equivalency relation was also applicable to the degree of carbide development. The mechanism of the tempering of martensite was demonstrated more clearly than in the earlier study. It was confirmed that carbides develop from martensite as poorly defined plates of the Fe2C type carbide followed by thickening of the plates with a transition to Fe,C. Finally the plate structure deteriorates into a lacy mass from which alloy carbides emerge as chunky particles that grow slowly with further increase of tempering temperature. Vanadium carbide derived from tempered martensite was found in characteristically small particles that tended to grow very slowly. The addition of chromium or molybdenum to a steel with predominant vanadium carbide tended to introduce carbides of a chromium- or molybdenum-bearing type having a somewhat larger particle size. The Cr,C, type carbide particles were larger than those of the V,C, type and somewhat smaller than the carbides in steel containing both Cr,C and M,C. Similar observations were made of the carbides in the pear lite of annealed steels. It appeared that high temperature properties would be benefited by the retention of the fine carbide particles that result from a balance of composition and heat-treatment designed to produce a maximum amount of vanadium carbide. Procedure: The steels used in the investigation were made with a base of Armco iron in a high-frequency furnace at the Union Carbide and Carbon Research Labs., Inc. The steels were deoxidized

Jan 1, 1951

By F. L. Holderreed

A choosy in what they would smelt. The furnace charge had to be coarse, and it had to be rich. They discarded fines in excess of about 1/10 the total weight. They wanted 10% copper content and fussed about anything with as low as 5%. They concentrated the copper content of the charge as much as they could by prior selection. They roasted off enough sulfur to further enrich the copper content of the succeeding fall of matte (a melt of cuprous and ferrous sulfides or Cu2S.FeS). Then they desulfurized the iron and fluxed it by carefully adding silica (quartz, not silicates) for a slag of lower density than the cuprous sulfide (Cu2S or white metal). After skimming off the slag, they further desulfurized the white metal by blowing the molten bath with compressed air. The result was blister copper. Yesterday Their techniques and furnaces? Some experimented with mechanically rabbled roasters, but their standard roasting practice was burning coarse sulfide ore in 250-ton heaps. These heaps, approximately 24 x 24 x 6 ft, were burned for about 75 days down to 6-10% sulfur. The turnaround time for a given roasting position was 100 days. Assuming the base was a hearth, the calculated rate of treatment was on the order of 0.004 tpd per sq ft.

Jan 1, 1971

By Z U Bajwah

During the Palaeoproterozoic, a large number of granitic intrusions were emplaced in the various parts of the Pine Creek Geosyncline (PCG). In the central region, the granitic magmatism is represented either by the coalesced mass, eg the Cullen Batholith, or individual plutons such as the Mount Bundey Granite which together with the Mount Goyder Syenite intrude the metasedimentary strata, causing wide spread contact aureoles. Some of these granitic intrusions are temporally and genetically related to gold (and less commonly base-metals) mineralisation present in the adjacent metasediments. These plutons are characterised by the presence of biotite and homblende which appear late in the paragenetic sequence. Electron microprobe analyses of biotite and homblende show that these minerals are poorly to moderately zoned. Biotites are characterised by a decrease in Fe/(Fe + Mg) ratios when plotted against AIVI. Similarly a modest decrease in Ti from centre to the margins of the biotite crystals has also been observed. Furthermore, an increase in Mg/(Mg + EFe) ratios from centre to the margins as well as in mafic to felsic rocks is also apparent. On the other hand, homblendes from the granitic bodies display less well marked trends and are poorly zoned. However, they show systematic increases in Mg/(Mg + EFe) ratios, and decreases in Fe, Al"' and Fe/(Fe + Mg) ratios, when plotted against Si. Magnetic susceptibility measurements on powdered samples of the plutons give results characterised by high values ranging from 0.8 x 10-4 to 2.0 x 10-3 emu/g which place the granites in magnetite- series field. This indicates that the oxidation state of the magma was high during crystallisation. The range of chemical compositions of the mafic phases indicates a rise in the oxidation state of the magma as it progressively became saturated in H20-volatiles and other metals, not partitioned into the earlier crystallised phases in the final stages of magma consolidation. These variations in chemical compositions also indicate that initially fOz was high and became progressively higher during fractional crystallisation of magmas; this subsequently led to the emanation of hydrothermal fluids responsible for the mineralisation in the adjacent metasediments.

Jan 1, 1994

By Bruce T. Stanley

The concepts of ore reserve estimation at the Henderson mine are reviewed presenting a geostatistical approach and procedure as applied. Specific problems encountered are recapped and explained as to the nature and resolution thereof. The methodology and results are shown, along with an approximation of computer usage and capacities needed. The scope of the paper is to set forth an example of actual application, usage, and benefits realized from such a procedure. Local Conditions The Henderson molybdenite deposit is located in central Colorado about 69 kilometers west of Denver. The geology consists of a classic subvolcanic ryolite porphyry sequence with quartz-molybdenite mineralization occurring in an extensively fractured granite stock complex. Being assymetric and bilobate in section, the orebody measures approximately 300 meters thick and 600 meters by 1200 meters in plan. The orebody is sampled by means of underground drill holes which create an east-west fan pattern spaced roughly 60 meters apart in the north-south direction. Approximately 27,000 meters of drill hole assayed on 3.04-meter intervals were available for analysis. Recovery on the core is about 95 to 100 percent, thereby affording us with reliable data all prepared to the same standards.

Jan 1, 1977

By Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Cameron Mitchel

Brow hazards are a significant concern in coal mine ribs and form when weak coal sloughs out of a rib face and exposes an overhanging block of more competent rock or coal. Of 36 rib failure fatalities in the last two decades, 36% resulted from rib brow failures. This highlights the need to better understand the mechanisms driving brow formations and failures to mitigate this hazard and eliminate potential fatalities. The research team at Missouri S&T worked to enhance the current CPRR system and include the potential for these brow hazards. We employed physical modeling methods to build a scaled model from critical brow cases observed in the field. The dimensions and properties of the models were scaled down by 14.4 times from the field cases. The results of the physical modeling efforts were used to assist in calibrating distinct element numerical models vital to understanding brow formation and failure mechanisms. Subsequently, three physical models were created and tested to provide data on an otherwise impossible-to-capture event at the field scale. The results of these tests provided formed brow dimensions that agree well with those observed at the field scale. The brow dimensions were 1.25 inches deep into the rib, equivalent to 1.5 feet when scaled up. Similarly, the numerical modeling efforts provided good agreement by capturing a brow forming 1.55 inches deep into the rib. The physical model results further validate the applicability of physical modeling efforts for capturing otherwise difficult and dangerous phenomena in a controlled lab setting.

Feb 22, 2026

By James L. Oleson, Hunter R. Propsom, Kevan J. R. Ford, Robert D. Henderson, Bob Musgrove

"Kinross’ Fort Knox Gold mine, near Fairbanks, Alaska has successfully implemented two major metallurgical continuous improvement projects resulting in growth of gold production and an extension of mine life. In 2009, Fort Knox produced 263,153 oz of gold at a cash operating cost of $543/oz. In 2010, approximately 63% of the gold will be produced from the CIP circuit, 15% of the gold from the gravity circuit and 22% of the gold from the heap leach.In 2009, a 44,000 ton per day run-of-mine valley fill heap leach facility was constructed and commissioned as a cost effective treatment option for low grade ores to supplement the higher grade mill. The heap leach facility will produce approximately 100,000 ounces of gold per year under severe winter conditions. Heap leach gold recovery, based on test work shows 30% after a 55-day leach cycle, with long term ultimate gold recovery targeted at 65%. The paper presents the heap leach design concepts and production data.Additionally in 2009, installation of a Knelson gravity concentrator unit (XD70) was completed. This together with an Acacia intense leach reactor (AILR) has increased overall mill gold recovery from 79.3% to 80.7%. A manual shaking table gold recovery operation has been replaced by batch intensive cyanidation of the high grade Knelson concentrates. Increased removal of coarse gold and difficult-to-leach gold species from the grinding circuit, via the gravity circuit, has improved gold leach recovery in the conventional whole-ore tank leach CIP circuit. The paper presents plant operating data, showing the improvements over the old flowsheet.Focus on the metallurgical properties of the high grade and low grade end components of the Fort Knox ore has resulted in significant improvement to gold recovery."

Jan 1, 2011

By Oliver Bowles

SUPERFLUOUS varieties and standards which are meriting the critical scrutiny of the manufactur-ing industry have a special significance in the non-metallic mining industries, where, many of the final or intermediate products are manufactured at the mine or quarry. Such processes of manufacture must be considered an integral part of mining in its broader sense. Improvements may be either elimination or standardization. - The chief requirement of elimi-nation is an agreement between consumers and pro-ducers based on facts deduced from: statistical data. Standardization is much, more complex. Standards .may be established only when a very; thorough knowledge has been gained of the physical and chemical properties of the products, and the requirements of consumers. The activities of the Bureau of Standards are. largely directed toward such determinations. Paving-brick manufacturers, together with highway engineers, representatives of certain engineering socie-ties, and Government bureaus, have agreed that of the 66 styles of paving brick on the market 11 only are, essential and 55 are superfluous. Steps have been taken to reduce the output of -all but the 11 standard types. It is customary for manufacturers of structural slate to prepare it in sizes specified by builders and architects. Thus the material cannot be manufactured in advance and the result is irregular activity of mills, delays in filling orders, etc. To improve this condition, the Structural Slate Co. has issued a series of pamphlets giving complete specifications of structural slate for various purposes. Architects find it so much easier .to, order slate from these sheets that standard sizes are specified in preparing plans for new structures. Slate switchboards are usually manufactured after. the order has been received. One manufacturer claims that 80 per cent. of all switchboards are of standard sizes, and he keeps such sizes in stock. The facility with which orders may be filled from stock, and the improved quality of seasoned switchboards, will undoubtedly influence electrical, companies toward a more uniform standardization in size. Simplicity, could be further attained by the elimination of minor irregularities in .style; for example, in the beveled. edges.

Jan 2, 1922

By D. W. McGlashan

[Becaune ad ;the extennive nwrgace anea od u.X chopRex2 in emmiom, emuhion dRokdtiun oddeh poaaibWa don ;the necove/ry ul; BinQey divided minmcd pa~LL&a, Swr~aC;tavu% mu2 akab&ze ;the emu-bion and poan an an ad~i&y don ;the dahed mina&. OZhm hpohtant acto oh me ;the naAwre od ;the em&iun inghedied, ;the nQRaLLve volwna 06 the colz;tinuoun and dincon;tinuoun phaa, ;the change aign bonne by the dnuplm ad the o.X phae, ;the z&a pu;tenticd od ;the dahed minmd, the ~olubRe am curdent 06 khe wcr;ten-pulped and gnuund onu. AX on nem ;the AoQRec;trtic point on ZPC, ;the doubRe Raym about ;the minW-&den oil dnopR& i~ neduced in ;tkichnaa and the dn_opR& wU codace and continue to aggnegate into agglommaka . Invetmion dnom O/U ko W/O can UCCWL depending upon a nwnbm a 6 in;tmQeaked daotuh~. EReothokin&Lc inn&wnenta;t/iun to meanwre ;the ZPC, QReckProphonQkic mobilXty z&a pokeW and hakerning cuttrtent me invcduabte in ;the appficatiun ud emu-bion dRo;tat;iun ;to m&~c and nonm&~c minu.&. ] INTRODUCTION Recent interest in emulsion flotation can be ascribed to the necessity of selective separation and concentration of extremely fine minerals. That which follows is an elucidation of the many factors-in emulsion technology in application. In applied surface chemistry for solid-particulate separation and concentration, emulsion flotation is one of the intermediate processes between froth flotation, in which the continuous phase is water (99.5 to 99.999% by volume), and particulate extraction, in which the continuous phase is almost entirely an organic-fluid. Another intermediate process is particulate exchange (or partition) in which immiscible or very limitedly miscible phases are in controll¬ed but appreciable volumes. Surfactants are common to all of these

Jan 1, 1968

By M. Fafard, D. Picard, J. -F. Bilodeau, G. Soucy

To simulate adequately the behaviour of a Hall-Heroult electrolysis cell, a finite element model must take into account the properties of each material. However, it has some lacking knowledge on the mechanical behaviour of materials, like the long-term visco-elastic (creep/relaxation) behaviour of cathode. A three-dimensional model is then proposed in this paper and will be ready to be implemented in the finite element code FESh++. The model was developed using the three-dimensional model based on thermodynamic of irreversible processes where the choice of the internal variables is based on a phenomenological approach. All parameters of the model are represented by constant constitutive tensors and the temperature and chemical dependencies are taking into account through scalar functions multiplying the constant constitutive tensor. The goal of the first part of this project was to determine the parameters of the threedimensional visco-elastic model at the reference state (virgin material at ambient temperature) of three different cathode materials. This paper presents the theoretical model and the results of creep tests at ambient temperature for the semi-graphitic carbon cathode.

Jan 1, 2006

By Javier Ramirez

"Recent R&D pilot plant testing was done to validate a full industrial scale system for recovering residual magnetite from the tails of an iron ore concentration plant. The recovery system is based on an autogenous heavy media separator treating a tailings slurry at 0.45% solids by weight. A 3,100 m3/h capacity concentrator was installed based on the testing findings. Excellent metallurgical results have been observed in two years of continuous operation. This experience is the basis for the proposal of a novel process consisting of the preconcentration of base metals ores; the idea being to obtain a heavy bulk concentrate of the polymetallic minerals and discarding in one step the light gangue mineral components. The bulk concentrate then proceeds to conventional froth flotation. The reduced volumetric flow of the bulk concentrate allows a reduction in the size of the subsequent flotation circuit. A prerequisite for the heavy media separation is a fine size grinding of the ore and a correspondingly high degree of liberation of the mineral species to be recovered. A process scheme is also presented in which the gravity concentrator works in conjunction with a companion tailings thickener for process water recovery. The underflow from this thickener, having paste consistency, can be sent to a tailings dam or mixed with Portland cement for mine backfill. The process water in the system is managed at an estimated recovery in excess of 98%. Additional R&D work using this novel approach is being considered by a large iron ore concentrator for removal of liberated silica from the final concentrate; and for upgrading 3.5 million tons of a marginal hematite reserve owned by the mining company.INTRODUCTIONGravity preconcentration (static and dynamic) of sulphides prior to froth flotation has been and is being practiced at various concentrator plants (Asarco´s Young Mill: heavy media cone; Mount Isa: DSM cyclone; Afton Mines: Denver jigs; Tsumeb Mine: Reichert cone) (Burt, 1984). The idea behind installing preconcentration equipment is to reduce the volume of feed processed on flotation, thus requiring smaller flotation plants although other advantages may be of importance, such as obtaining richer concentrates due to higher grade feed, better process water and energy management, and reduced flotation reagent consumption.The SedconTM solid/liquid separator is a versatile process unit patented in Mexico (MX/u/2007/000305). As a gravity device, it may be classified as an autogenous heavy media dynamic concentrator. Figure 1 depicts the Sedcon (Sedimentador de conos) separator. The four main components are as follows: the feedwell for efficient mixing of the pulp with dilution water and flocculant (and coagulant for water clarification); the inner cones (passive elements for solid/liquid separation); the discharge underflow cone; and the scraper mechanism. The standard discharge cone is a 60° inclined cone for general applications. For paste tailings thickening applications, a deep cone with a 69° inclined cone is used."

Jan 1, 2016

By Charles H. Jacoby

In 1774 a Swedish chemist, C. W. Schule, first recognized manganese as an element. That same year Schule's associate, J. G. Gahn, isolated the element manganese for the first time. In 1856 the Bessemer process of steelmaking gave birth to the economic importance of manganese. Later, in 1882, Robert Hadfield discovered high manganese steels. Although the primary use of manganese is in the ferroalloy industry, two additional important uses for manganese are making chemicals and dry cell batteries. Manganese is also vital to plant and animal life. Various chemical compounds of manganese are used in fertilizers, feeds, glass manufacture, paints, varnishes, and for numerous medicinal and chemical purposes. For the study of industrial minerals and rocks, only the chemical and battery grade material is of concern, but for the sake of comparison, metallurgical aspects are included in this presentation. Although currently the world's largest consumer of manganese, the United States is producing only minor amounts of ore at the present time. This is due primarily to the fact that although huge deposits of manganese occur within our borders, all are of such low grade as to be economically unfeasible to mine. For many years various government agencies and segments of private industry have devoted sizable sums of money and time in an attempt to upgrade ores from the various deposits, and also in an attempt to recover manganese from blast furnace slags. In view of current world prices, and the quantity of high grade material available, there is little likelihood that any of these approaches will be found to be economically feasible in the near future. Geology and Mineralogy Mineralogy There are over one hundred minerals that contain manganese. These minerals vary from those with compositions that are predominantly manganese to those having only minor percentages. [ ] Geology From a geological standpoint most manga¬nese deposits are complex. In general, it can be said that all primary deposits of manganese are carbonates or silicates. The most productive and profitable have been those of sedimentary origin and residual concentrations. Examples of these residual types of deposits are associated with the metamorphosed lodes of Madhya, Pradesh, India, and the lateritic deposits of Orissa and Bihar, India; nodules in the residual clays of the Philippine Islands, U.S. southern Appalachians and Arkansas, Ghana, and Brazil. Sedimentary manganese deposits are best exemplified by the Nikopol district of Russia and the Tchiatouri area of Georgia, USSR. Hydrothermal replacements are characterized by the rhodochrosite deposits of Butte and Phillipsburg, Mont. In general, the hydrothermal type deposit has not resulted in any large tonnages being produced, but may have given

Jan 1, 1975

By William L. Porter

From the first day of new miner training until the day they retire, mine workers will experience changes due to the normal aging process. It is an unfortunate fact of life that many age-related changes result in diminished physical, sensory, or cognitive capabilities. Of course, workers also gain a tremendous wealth of experience, knowledge, and insight as they age, making them a vitally important resource for their company. Effective leveraging of this precious resource requires both an appreciation of the changes that occur with age and an understanding of methods that can be used to reduce the injury risk that may result. The purpose of this training is to provide the information necessary to accomplish these objectives. Aging workers may not necessarily have a higher injury risk overall; however, the effects of a musculoskeletal injury (MSI) on older workers may be more extreme. MSHA data show that not only does the percentage of MSIs increase when workers are over age 30, so does the number of days lost per injury, as shown in the graph below [MSHA 2005]. [ ] Protecting the safety and health of aging workers requires matching the demands of the job to worker capabilities. This means reducing or eliminating risk factors for injuries, such as heavy lifting, awkward postures, static postures, repetitive movements, and/or vibration exposures. In other cases, it may mean improving visibility or streamlining processes. Designing jobs to accommodate the changing capabilities of older workers will not only reduce injury risk for older workers, it will have the added benefit of protecting younger employees as well.

Jan 1, 2008