Search Documents

By Robert H. Merrill

A method of determining the strength of a mine roof layer in place is described in this report. The method was tested on a limestone roof layer 50 feet wide, 100 feet long, and 20 inches thick. In place measurements were accomplished by introducing air under pressure into a separation between the layer and the overlying roof, and as pressure was increased, the corresponding strain and deflection of the roof layer were measured until the roof failed. The ultimate strength of the roof agreed with the tensile strength of the roof rock (modulus of rupture) as determined in the laboratory; the modulus of elasticity as measured in place did not agree with the laboratory-determined values; the deflection and tensile strain in the layer in place showed good agreement with the theory of a body-loaded beam clamped at both ends. This procedure for determining the strength of a mine-roof layer is safer and less costly than successively widening a roof to failure. For example, it would have been necessary to mine the room to a width of 114 feet and a length of 228 feet to produce failure in this roof layer. The method is not necessarily limited to limestone; any thinly bedded rock type can be tested by this procedure when there is an open parting over the mined area.

Jan 1, 1958

Occasionally it is interesting, and sometimes useful, to review the past for early references to our industry, and to learn of the trials and travail passed through before it arrived where it now is - and the results of such a review follow. Some time ago one of our modern playwrights and poets, Arthur Guiterman, turned to coal, with the following result : Afar in the Carboniferous time I grew in Paleozoical slime, A lepidodendron with boughs on my stem And lepidostrobusea grew out of them. My roots in the mud of the ages I spread And up to the heavens I vaunted my head, I throve in the heat of tropical sun, And now I am coal at two dollars a ton.

Jan 1, 1935

By J. A. Finch

Individual mineral cyclone performance curves were determined for the four major minerals at two lead-zinc concentrators. Sizing was by screen and cyclosizer down to approximately 10 um, with lead , zinc and iron as saying of each size fraction. The performance curves were similar in shape and located according to the mineral specific gravity, Pm. The curves displayed a discontinuity at the fine end and a magnitude of short-circuiting of fines to the underflow which increased with Pm. Mass fraction of water to the underflow was only a guide to this short-circuiting. Sharpness of separation seemed in dependent of Pm. An inflection in the over-all performance curve was shown to be a consequence of the individual component mineral performance. A general relationship was observed showing that the flow regime of classification changed from laminar/ intermediate to turbulent with increasing cyclone feed size. Individual mineral size reduction for the four major minerals at one of the concentrators was also determined. Size reduction of the silica was greater than that of the galena, in contradiction to their accepted relative grind-ability. The observation did correlate with silica being much coarser than the galena in the feed to the ball mill. It is suggested that the silica acted as a buffer to the galena.

Jan 1, 1977

By V. N. Bryant

"1.0 SYNOPSISThe Colomac property, located 137 miles by air northwest of Yellowknife in Canada's NWT. will recover gold from 10,000 tons per day of open pit ore.The decision to proceed with the project was based on a mineable ore reserve of 16 million tons (including dilution) averaging 0.064 oz/ton. After an in-fill drilling program in the latter half of 1988, Colomac's mineable, proven and probable ore reserves were increased to 28 million tons averaging 0.056 oz/ton of gold.A feasibility study completed by Wright Engineers for Neptune Resources in December 1987 examined the possibility of vat leaching followed by C.l.P. and electrowinning. A second feasibility study completed by Wright in February 1988 demonstrated that a conventional agitated leach circuit using a finer grind justified the higher capital cost of this process. This study was accepted and formed the basis of the project authorization.Preliminary engineering commenced in April 1988 and detailed engineering was started in September of that year with the objective of a mine/mill start-up by early 1990.The short time period available to meet the project deadline was additionally challenging, as site access is either by plane year round, and winter road from early February to late March. Normal lead times for equipment design, specifications, quotations and bid analyses were not possible, if the winter road time-slot was to be met."

Jan 1, 1990

By Xuan Cheng

The electrochemistry of sulfide mineral flotation is reviewed with particular emphasis on galvanic interaction among minerals and grinding media, and its relevance to flotation of complex sulfide ores is discussed. Surface alteration due to galvanic interactions among chalcopyrite, pyrrhotite and mild steel is analyzed in terms of voltammetric and chronoamperometric studies on individual minerals and through galvanic current measurements in 2- and 3- electrode combinations. The results are related to laboratory flotation behaviors of chalcopyrite-pyrrhotite mixtures simulating copper-nickel bearing Duluth gabbro.

Jan 1, 1993

By John W. Cash

The mineralogy and textures of cyclone dust, sludge, and occasional build-ups in the American Iron and Steel Institute (AISI) direct ironmaking pilot plant at Universal, Pennsylvania have been studied by reflected light, transmitted light, and cathodoluminescence microscopy, and phase compositions have been determined by SEM-EDS. The cyclone dust consists of particles of carbon, metallic iron, sulfur-bearing iron, and wustite. Measurements of particles in the sludge indicates that 69% are less than 2.5 um across, 21 % are 2.5-5 um, and 10% are larger than 5 um. Mineralogically the sludge particles are mainly carbon and metallic iron, with minor wustite and sulfur-bearing iron. Build-ups that sporadically develop in the furnace consist of olivine, hercynite spinel, metallic iron, wustite, pyrrhotite, pseudobrookite, akermanite-ferroakermanite and gehlenite. The microtextures shown by the build-ups indicate that much of that material has precipitated at the build-up loci. This study has been supported by AISI and the U.S. Department of Energy.

Jan 1, 1995

By Vladimir I. Skorohodov

The technology for copper utilization from circuit boards etching is proposed. The technology is based on combination of electrochemical and sorption methods. The conditions of copper electroextraction from ammonia-chloride solutions with obtaining of cathode copper are defined. The stage of electrolysis is destined for copper recuperation from etching process. Due to the electrochemical processes are unacceptable for cathode precipitation of the copper from diluted solutions such as rinse waters, the concentration on the strong-based cationites are used. After filtration throw the sorption columns solution is directed to the stage of circuit boards washing. It allows organizing close loop water recirculation. After saturation. resin is 'regenerated by chloride ammonium solutions. Obtained eluate directed to the etching stage, Generally. the technology provides copper recuperation and minimize wastes amount.

Jan 1, 2001

By Will B. Jamison

Man's material advance from one level of civilization to the next has involved the development of new, more useful tools and the utilization of energy greater than he alone could produce. These two essentials for material progress have developed at an ever increasing rate in the last century. While the first really successful use of mechanical energy derived from burning fuel was in James Watt's steam engine which pumped water from coal mines in Cornwall about 1770, there was still very little use of mechanical energy in mining by 1900 except for pumping and hoisting. Compressed air, having some of the characteristics of steam and which operated engines not unlike steam engines or steam hammers, powered the first attempts to mine coal with energy greater than human muscle could provide. When direct current-powered traction cars replaced horse-drawn transportation cars on city streets, it was natural that direct current locomotives should begin to replace animal and human power in mine haulage. Slowly, trolley and battery locomotives were developed and introduced. With d-c systems being established for haulage, it was natural that improved cutting machines should be developed and powered by d-c motors. Thus began the years of

Jan 5, 1960

Reduce fire warning time and avoid activation of false alarms in underground mines. Approach A heat activated stench/tracer gas system was developed which automatically releases the gas mixture into the mine ventilation air. How It Works A canister approximately 12 inches long and 3 inches in diameter is charged with 50 grams of ethyl mercaptan or other appropriate stench gas and 500 grams of instrument detectable Freon. The canister is then pressurized to 100 psi with nitrogen. A disc is used to seal the contents of the canister. A low-temperature alloy designed to melt at a predetermined temperature is used to restrain a spring loaded plunger. Upon exposure to heat, the alloy melts and the plunger is released. The plunger ruptures the disc and the mixture of stench and tracer gas is released from the canister. Canisters are mounted in areas of a mine which are susceptible to fire such as near

Jan 1, 1983

By B. Ladanyi

An adequate knowledge of the overall behavior of a rock mass at a given site is fundamental to the satisfactory design of a rock slope. The be- havior is controlled by a variety of factors, in- cluding rock type, geological structure, stress and ground water conditions. There are essentially three lines of approach that may be used to obtain information on the in-situ rock mass behavior for the purpose of the design of a rock slope: (1) Direct measurements of rock mass properties by means ol laboratory and field tests. (2) Evaluation of rock mass properties from a study of slope failure case histories and sta- tistical information on stable and unstable natural rock slopes. (3) Evaluation of in-situ behavior of rock mass by using a physical or mathematical model technique.

Jan 1, 1980

Draftsman and transitman for coal-mine work in middle West. Salary $125 per month. No. 277. Surveyor and mine sampler for development company in Mexico. Applicant must be willing to interest himself in mine sufficiently to, act as assistant to the superintendent and be able to take charge in case the superintendent should be incapacitated at any time. No. 326. A copper company in Mexico desires services of engineer to act as chief chemist and flotation operator. No. 327. Instructor in mining and metallurgy, the work being chiefly in mining for college in middle West, to start Dec. 1. Salary $1200 to $1400. No. 328. A copper company in Mexico is increasing its force of underground foremen and desires the services of two men competent to act as assistant underground foremen. Chances for advancement excellent. Knowledge of Spanish is required. Salary to start $200 per month. No. 329. Young man for core-drill work for coal company. No. 330.

Jan 7, 1918

By F. F. Peng

Fine Coal Cleaning Processes including froth flotation, aggregative flotation or oil agglomeration, depend upon the wettability of coal particles in the aqueous solution. The wettability of coals of various ranks, hydrocarbon oil treated coals and oil-agglomerates have been measured using film flotation, induction timer, and froth flotation. Various hydrocarbon collector dispersion techniques are used to alter the surface wettability of coal particles. Change in wettability behaviors, measured by flotation responses, due to various ranks with or without of hydrocarbon collector modification are explained in terms of surface chemistry modifications as analyzed by induction time, film flotation as well as DRIFT Spectroscopy. The relationship between the wettability of coals and collector treated coals, and floatability are discussed.

Jan 1, 1993

By C. K. Man

Coal dust explosions in underground coal mines are prevented by generous application of rock dust (usually limestone). If an explosion should occur, the rock dust disperses, mixes with the coal dust and prevents flame propagation by acting as a thermal inhibitor or heat sink. To investigate this process in more detail, a number of explosion experiments using various coal dust and limestone rock dust mixes have been carried out at the Lake Lynn Experimental Mine (LLEM). These were conducted in a single entry of about 1600 ft (488m) in length and initiated with a methane gas explosion. A consistent set of post-explosion floor dust samples were taken along the entry after each test. These dust samples have been analyzed in the laboratory using thermogravimetric analysis (TGA) and solubility to determine how the limestone rock dust behaved during the coal dust / rock dust explosions. The preliminary results are reported in this paper and indicate that the chemistry of limestone plays an important role in its capacity to inhibit coal dust explosions. The results also show that it may be possible to estimate the intensity of the explosion using these conventional methods of analysis. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By M. Fig, J. Brune, C. Strebinger, G. Bogin

"A fundamental understanding of flame propagation characteristics through and around obstacles is needed to accurately model methane driven longwall coal mine explosions originating or propagating in the gob. Experimental investigations of methane flames in horizontal cylindrical reactors with simulated gob (i.e. rock piles) were carried out alongside coupled Computational Fluid Dynamics (CFD) and combustion simulations. Stoichiometric methane-air mixtures were ignited in semi-open reactor vessels of 5cm, 9.5cm and 71cm diameter, all with a fixed length to diameter (L/D) ratio of 8.6. This was done both with empty reactors and also with a rock pile placed at the open end of the reactor. The rock pile length to reactor length ratio was fixed at 0.3, and the rock pile height to reactor diameter ratio was fixed at 0.33 for all reactors. The smaller two reactor experiments were modeled with ANSYS Fluent in 2D. Experimental results indicate that for this geometry a similar acceleration mode occurs across scales: that the flame speeds up an average of 40% as it passes over a rock pile with this profile. The model is able to capture several important features of the experimental results, including the significant increase in velocity, the speedup ahead of the rock pile, and the leveling off of the empty tube flame front propagation velocity. INTRODUCTION Explosions in underground coal mines are among the largest industrial explosions, known to result in the rapid combustion of 20m3 of fuel gas or more [1,2] Coal beds hold methane gas under pressure, and when the pressure is relieved through mining activity some of this methane is released. The methane then mixes with ventilation air and, if not sufficiently diluted, may form a combustible mixture, which may result in an explosion. Several large coal mine explosions have occurred around the world recently. These include the 2014 Soma Mine disaster in Turkey that killed 301 people [3], and the 2009 Heilongjiang Mine explosion in China that killed 108 [4]. Other recent mine explosions, including the 2010 disaster at the Upper Big Branch mine that caused 29 fatalities [5], have demonstrated that explosive gases can accumulate and ignite within and around the gob area of a longwall coal mine and then expand into the active mining face and nearby areas, endangering workers and equipment. If enough combustible gas is involved, the initial flame can accelerate, eventually transitioning from deflagration to detonation [6]. Researchers are developing a fundamental understanding of the evolution of the explosion process from the laminar kernel to the fully turbulent regime, and its propagation through obstacles such as those found in the gob. Researchers also studied the initial development of methane flames and the potential for the development of a detonation."

Jan 1, 2018

By Damien Gaboury

"Two practical methods for correlating two or more diamond-drill core intersections, using a stereographic projection software are presented. The first may be used to establish if two or more vein intersections are correlative, based on their core angles and diamond-drillhole attitudes. The second method allows prediction of main vein attitudes from numerous intersections, based on a spherical density contouring projection. The methods are suitable for: (1) correlating veins in complex orebodies; (2) ascertaining lateral continuity of ore for reserve estimations; (3) demonstrating the hidden complexity of an orebody; and (4) correlating and interpreting various planar elements.IntroductionModern mineral exploration relies on diamond- drill core data and on the ability of geologists to interpret them. Drill core generally yields unoriented information, unless an expensive orientation device is used. As a consequence, strike and dip of planar elements such as lithological contacts or mineralized veins cannot be determined easily. This is particularly true for blind deposits (covered by thick overburden) and complex orebodies, where field data cannot support drilling interpretations. Such a problem has been addressed previously using two and three diamond drillholes and several solutions were proposed based on trigonometry, and geometric and stereographic projections (Mead, 1921; Wisser, 1932; Fischer, 1941; Stein, 1941; Bucher, 1943; Gilluly, 1944; Addie, 1962; Mills, 1963; Lyons, 1964). However, these solutions are time consuming and not relevant to present day computerized data plots."

Jan 1, 1997

By M. Irish

This paper describes the emergency water control measures used at Pegasus Gold's Zortman Landusky mine during the September 1986 flood. The amount of solution stored increased by approximately 78 165 m3 due to receiving 0.2134 m of rain in a 24 hour period. Three methods of water disposal will be discussed including continuous chlorination, batch chlorination, and reverse osmosis. A water management program will also be discussed.

Jan 1, 1988

By Frederick S. Fisher

Three spatially separate porphyry copper/molybdenum deposits are associated with the Tertiary Needle Creek igneous center in the southern Absaroka Mountains, Wyoming. In all three deposits a central zone containing disseminated copper and molybdenum is surrounded by a halo of small, discontinuous base and precious metal veins. Propylitically and phyllically altered rocks are common in all three mineralized areas, and potassically altered rocks are locally present. Fission- track age data from apatite and zircon indicate that mineralization occurred about 32-40 m.y. ago. Limited data suggest that the lead isotopes are nonradiogenic, similar to porphyry copper deposits elsewhere in the western United States. The complex igneous history of the Needle Creek center has involved several periods of intrusive and probably extrusive activity. lntrusive rocks are calc-alkalic and include andesite, granodiorite, diorite, quartz monzonite, dacite, and rhyodacite. Stocks (1-30 kmz in exposed area), radial dike swarms, and sills make up the presently exposed plutonic masses and constitute lower-level vent fillings in an old stratovolcano. The Needle Creek igneous center is located approximately midway along a northwest-trending belt of intrusive rocks extending more than 100 km along the central axis of the Absaroka volcanic field. The igneous and mineralized centers within this belt were probably localized at the intersections of northwest- trending Laramide and possibly Tertiary fracture systems and earlier northeast-trending Precambrian structures in the underlying basement rocks.

Jan 1, 2013

By H. H. Uhlig

Soon after general use of stainless steels began, it was observed in practice that certain combinations of factors tended to induce corrosion by pitting. For most applications this was a serious drawback, not so much because the structural properties of the metal were impaired but because of the rapidity with which heavy sections of the alloys were penetrated by small elongated pits. These pits seemed to initiate readily in oxidizing metal salt solutions like ferric chloride and in chloride solu-tions like sea water. It was observed that in sea water pitting was more frequent in stagnant or polluted waters than in highly aerated, moving waters. The steels in these chloride solutions were observed to be sensi-tive to long contact with material such as sand grains or attached bar-nacles. At points of attachment or contact it was not uncommon to discover initiation of corrosion. Pits once begun at contact faces were observed to grow rapidly, usually elongating phenomenally in the direc-tion of gravity until the metal was perforated. Hydrochloric acid and other nonoxidizing acids, on the other hand, were observed to corrode stainless steels generally; the weight losses often were higher, but the penetration less than for the pitting type of corrosion. The causes of pitting, a type of corrosion recognized as character-istic not only of stainless steels but of many additional metals and alloys, are important in corrosion studies. A possible explanation bears prac-tical significance, for once it is known why pits begin where they do and continue to grow after initiation, intelligent direction can be given to diminishing corrosion. This can be done either by some alteration in the composition and treatment of the alloy or by some alteration in the environment. It appears foremost in importance to discover the nature of pit foci, for if initiation of pits can be discouraged their growth will be no longer a factor to be considered. In a multi-component alloy containing many impurities normal to production of such an alloy, each of which may play a part in pitting, and whose corrosion resistance is sensitive to heat-

Jan 1, 1940

By D. A. Baker, W. J. Mullin, T. P. Philip, P. A. Korpi

Some of you will recall from the last Randol conference held in Cairns, Australia in April 1991 that I shot my mouth off when I declared that I believe that these conferences are covering only a small slice of the overall mining industry pie because the major emphasis is on ore processing. The attendees at these conferences to date have been composed principally of metallurgists, which naturally leads to a preponderance of papers on this important feature, but it is only one of the areas of the mining business.

Jan 1, 1992

By T. Whitrnoyer, J. Sneckenberger

"The acOustic impedances of seven rat lungs were measured at frequencies between 100 and 6400 Hz. Rats were divided into two groups: a silica exposed group (N=3) and a control group (N=4). The silica exposed group was injected intratracheally with silica solution. Three of the control group were intratracheallyinjected with saline. Between four and six weeks after theinjections, all lungs were excised and degassed. Lungs were,suspended in a pressure Chamber, with the trachea canula attached to the end Of a tapered impedance tube. The lungs were subjected to transpulmonary pressures between -30 cm H2O and 6 cm H2O to simulate deflation and inflation. With transpulmonary pressure being held constant, the impedance tube was excited with random noise. A dual channel analyzer calculated H12(f), the transfer function between the two microphones. This function was used to calculate the lung's impedance at that pressure. The impedance magnitude spectra of both groups typically had peaks at 2000,3500, and 5500 Hz. Statistically significant differences. (90%confidence level or greater) between the two groups occur at the 3500 Hz peak at transpulmonary pressures of 20, 8, 6, 4, and 2 cm of H2O. This fact seems to confirm that this method can detect. lung disease. Further research will indicate whether this method will be able to detect the onset Of coal worker's pneumoconiosis.INTRODUCTIONOne of the first studies of impedance Of the human lung were conducted by DuBois et al.[2] using the forced OscillatiOn technique. This technique, however, was limited to frequencies below 30 Hz. Further studies by Van Den Berg [6] revealed thatthe lung reflected higher frequency sounds (100-10,000 Hz), instead Of behaving as an anechoic termination. This discovery has lead to several studies of the acoustical properties of both human and animal lungs at high frequencies [3,4,5]."

Jan 1, 1988