Search Documents

By Lon Santis, Gregory M. Rumbaugh, Christopher Mark

This paper examines the relevant theory, experience, and past practices relating to development mining near gas or oil wells. It addresses setback distance for both coal and stone room-and-pillar mining. This study also involved a review of accident reports involving well interceptions and downhole well surveys. It provides technical considerations for decisions regarding safe setback distances for development mining throughout the United States. The study’s scope is limited to mining near active or inactive (i.e., non-producing, abandoned or inadequately plugged) wells with known surface locations.

Jun 25, 2024

By Fuqiang Zheng, Yufeng Guo, Pengfei Li, Guanzhou Qiu, Tao Jiang, Andrew Yakovlevich Travyanov

Low content of TiO2 and high impurities content of Ca and Mg are the shortcomings of domestic ilmenite. To meet the requirements of the material in the titania produced by chlorination process and titanium sponge industry, enrichment of ilmenite is necessary. In the process of enriching ilmenite, high temperature and reductive condition were beneficial to the formation of anosovite, but the high content of magnesium oxide which was solid soluble in anosovite baffled the following separation. So the effects of pre-oxidation and reductive conditions including reduction temperature, reduction time and hydrogen concentration on the phase composition and metallization rate were studied. The characteristics of reduction samples were analyzed by X-ray diffraction and optical microscope. Results have shown that the reduction product is mainly composed of Fe, Fe(Mg)TiO3 and TiO2 at 1123K, its metallization rate is about 65%,magnesium exists in Fe(Mg)TiO3.

Jan 1, 2015

By Kenneth N. Weaver

Portland cement can be made from relatively abundant industrial minerals and rocks, and this may explain why cement producers placed little emphasis on geology during the early days of the industry. After World War II, however, the industry began to recognize the need for geological exploration, and some of the larger companies began to build a permanent geological staff. This development had its roots in the following factors: Rapid expansion of the industry; closing of many cement plants due to inadequate raw materials; necessity for upgrading the quality of portland cement; and the increasingly large capital investment required to build new cement plants, which in turn, required a higher degree of accuracy in reserve calculations. Whereas the geologist's function during the active expansion of capacity was primarily in exploration, one of his major functions today is the development of existing reserves.

Jan 1, 1965

By Patricia Curtis Petty

Thirty years ago, the appearance of a female mining engineer, geologist or miner in a company, union or mine environment would have been unthought of, unwelcomed and violently opposed. Twenty years ago, the intellectual perception of the news that women were interested in becoming mining engineers, geologists and miners had been accepted by the industry-but no one wanted to be the first to hire one of these exotic creatures. Ten years ago, those who had been most vehemently opposed to the philosophical idea of women working in these areas were faced with competent, productive engineers, geologists and miners-who only incidentally happened to be women-and began hiring them. Historically, of course, one can always find the isolated individual who worked in these areas-the first female graduate of the Colorado School of Mines with a mining engineering degree graduated in 1903-but the concept of woman as professional engineer was very slow in arriving in the United States. The few who worked as miners generally worked in small family enterprises, such as some of the coal mines in both Eastern and Western United States. Others accompanied husbands or sons into wilderness areas searching for gold and other precious metals.

Jan 1, 1984

By W. M. Schafer, C. F. Luckay, D. A. King

Monitoring devices have been installed at several mine sites to assess the potential for the development of acid rock drainage (ARD) in waste rock, spent ore and tailings material. In addition, instrumentation has been designed for monitoring changes in water quality in pit lakes. These devices monitor temperature, oxygen, water movement and water chemistry in the waste rock pile. This information can be used to evaluate the current and future ARD risks and the effectiveness of caps and covers. The information can also be used in the design of other reclamation strategies that limit ARD development. The instrumentation includes nested thermistors and oxygen sensing ports, neutron access tubes, heat dissipation units (HDUs) and lysimeters. Many of the monitoring devices can be linked to a data logger and telemetry systems, enabling monitoring data to be downloaded from the office.

Jan 1, 1999

By J. E. Clemson

The Black Pine sediment-hosted, disseminated gold deposit is located in Cassia County, Idaho. Gold mineralization occurs in flat-lying zones 50 to 100 feet thick. Total geological ore reserves are 5.6 million tons grading 0.049 oz/t. Ore types include: non-carbonaceous, oxidized ore; carbonaceous, sulfide ore; and carbonaceous, partly oxidized ore. In the oxidized ores, native gold grains commonly occur in porous hematite pseudomorphs that have replaced disseminated framboidal and euhedral pyrite, and this gold should be readily leached by cyanide solutions. Approximately 4 % of the native gold observed in the oxidized ores is locked within gangue and may be refractory to cyanide solutions. Native gold has not been observed in the unoxidized samples, all of which are characterized by primary sulfides. It is suspected that the bulk of the gold mineralization in the sulfide ore occurs as submicroscopic particles within pyrite and will be refractory to cyanidation. It is believed that much or all of the gold observed in the oxidized samples was originally in pyrite but was released and re-precipitated during oxidation. The degree of oxidation of the pyrite and the presence/absence of preg-robbing carbonaceous material is used as a guide in delimiting zones of mineralization amenable to heap leaching.

Jan 1, 1988

By John R. Bartels

Jan 1, 2009

By Daniel Saint Don, Jacques Dumouchel

QIT Madagascar Minerals (QMM)’s heavy mineral sand deposit located near the Village of Fort Dauphin, Madagascar was recently drilled using Boart Longyear Company’s Mini-Sonic drill. Continuous sand core samples were obtained to a depth of up to 30 meters for analysis and compared with the existing drilling data. Results were used as part of a validation process of the resource estimate, based on approximately 1,500 exploration holes drilled to date.

Jan 1, 2005

By S. K. Das, A. J. Gesing

This paper provides an overview of North American markets for magnesium and aluminum alloys along with life cycle material flow diagrams. Additionally, we review the production processes of magnesium and its alloys from various magnesium-bearing raw materials, including scrap. The main focus of the paper is on the collection, recycling and processing of post- and pre-consumer metal scrap containing magnesium. We discuss the latest status and economic analysis of RE-12™, a scrap-based process for recovering magnesium from aluminum alloys and its potential application to can sheet, automotive (body and closure sheets) and aluminum foundry markets.

Mar 1, 2017

By Wilbur L. Webb

An electrically powered methane sampling system for application on mining machines was designed, fabricated and laboratory tested. The system will sequentially draw sample air at a controlled rate from up to three machine positions across the mine face and deliver the air to either an approved methane monitor, methanometer or flame safety lamp. The prime considerations in the design were to provide an intrinsically safe, water and dust resistant control box and an explosion-proof power box capable of being operated from the various mining power sources. The power box contains an internal battery that provides operating power prior to mining machine start-up and alter machine shut-down. The internal battery is recharged automatically when mining machine power is available.

Jan 1, 1977

By Pedro Cunha Alves, Wagner Viana Bielefeldt, Vinicius Cardoso da Rocha, Julio Aníbal Morales Pereira, Antônio Cezar Faria Vilela

A limpeza e a reoxidação de um aço SAE 1055 modificado foram avaliadas durante a sua produção em uma aciaria elétrica. Escória A no sistema óxido CaO-SiO2-MgO-Al2O3-CaF2 (CSMA-F) e escórias B e C no sistema óxido CaO-SiO2-MgO-Al2O3 (CSMA) foram analisadas. Duas amostras de aço foram coletadas em ambiente industrial: forno panela e barra laminada. ASPEX Explorer foi utilizado para obter informações sobre as inclusões, organizando-as por composição química, tamanho, densidade e tipo. FactSage v7.2 calculou as inclusões formadas durante a solidificação do aço, fração líquida e sólida das escórias e viscosidade da fração líquida. Após o refino secundário, o tipo mais comum de inclusão encontrada foram os aluminatos de cálcio. Na barra laminada, o espinélio foi o tipo de inclusão mais frequente, indicando um possível produto de reoxidação. Sua formação pode ser causada devido a interação com os materiais utilizados no distribuidor e molde. A redução da temperatura também favorece a formação de espinélios, como demonstrado pelo FactSage. As inclusões de espinélio foram analisadas pelo método Função de Densidade Populacional (PDF), que identificou que as corridas A1, A2, C1 e C2 apresentavam inclusões de espinélio formadas por reoxidação. Uso de escória no sistema CSMA é indicado já que eventos de reoxidação foram diminuídos nas corridas B1 e B2. No entanto, é necessária uma análise mais profunda dos materiais utilizados no distribuidor e molde para melhorar a limpeza do aço SAE 1055.

Oct 1, 2019

By A. V. Tarasov

A flow-sheet for waste-less processing of spent lead batteries comprises mechanized separation of batteries, smelting of the metallic fraction in a kettle, electrothermal smelting of oxysulfate fraction, refining of crude lead and processing of reverts to produce commercial products. Smelting of lead-containing fraction is performed in an electrothermal furnace using a processing technology developed in the Gintsvetmet Institute and differing from conventional processes by the fact that it does not require any fluxing agent (soda); no matte is formed in the process and the amount of slag produced is minimal, because its formation depends only on the ash content of coke and the quality of battery scrap separation. The process has been patented. It has been introduced on a commercial scale in 1.8 MVA furnaces at the plant of A0 "RyazTsvetmet" (Ryazan, Russia). The process has the following main advantages as compared with conventional shaft-furnace smelting and smelting in a short-drum furnace: the process does not require technical-grade oxygen, the amount of process gas generated is minimized ensuring a decrease in lead-containing dust and sulfur dioxide emissions by 3 to 5 times per unit of lead recovered; a decrease in dust entrainment resulting in lower amounts of recycled dust; lower slag yield (a decrease from 20-25% to 3-5%); lower coke requirement (a decrease from 10-14% to 3-4%). Refining of crude lead is performed using conventional technology but there are several unique features for which know-how is available. Processing of by-products of electrothermal smelting and secondary lead refining (slag, drosses, skimmings) and ebonite fraction (crushed battery casings) is performed in a slag-fuming furnace.

Jan 1, 2002

By Earl C. Hutchison, Wade C. Hutchison

T 0 effectively evaluate property damage that is claimed to have been caused by blasting activities and in order to lay the proper foundation to build the best legal defense, identification of the actual causation for the damages are necessary. For the past twenty years, engineering personnel from VCE, Inc. (previously Vibration Control Engineering, Inc.) have been evaluating claimed blasting damages with pre- and postblast inspections, with analysis of seismic levels, blasting amounts at given distances, and with other engineering considerations. In addition to these evaluations, they have also documented other causes for damages which are of the types that are often claimed as blasting damage.

Jan 1, 1995

By R. Al-Hent, M. Aissa, J. Asfahani

"This paper focuses on determining the favorable geological and hydrogeological conditions for forming uranium occurrences in the Froqlos-Jabal Abou Rabah region, Palmyrides, Syria. Eighty rock samples from this area were analyzed by spectrometric gamma-ray technique to determine the radioactive concentrations of eU and eTh, and of %K. Uranium concentrations in shallow and deep groundwaters were also determined. High uranium concentrations were registered owing to the presence of phosphatic outcrops in the study region. The uranium migration trends and its remobilization were analyzed through the analysis of the behavior of eU, eTh, and their ratio. A positive relationship between eU and eU/eTh, and a negative relationship between eTh and eU/eTh in geological formations of different ages supports the secondary remobilization of uranium. The role of groundwater movement in transportation and redeposition of uranium mineralization is discussed: deep waters are less oxidizing than near-surface waters, and do not appear to have significantly remobilized uranium. This indicates that the source of secondary uranium mineralization is surficial or near surficial, and is mainly related to the leaching of outcropping phosphatic layers.Integration of the results with established radioactive and geological sections reveals four radioactive anomalous zones: north Froqlos, Kherbet Hannora, northwestern flanks of Jabal Abou Rabah (Kherbet Al-Hajar), and the northwestern limit of the Ghuntor depression. The high uranium concentration in north Froqlos is because of its original presence in the phosphate beds and extensive fracturing, which allows groundwaters to penetrate and remobilize the uranium. High uranium concentrations in the other three locations are caused by the presence of evaporites and capillary action, which draws solutions upwards and causes redeposition as surface crusts (gypcrete)."

Jan 1, 2009

By Dae S. Young

A new probabilistic approach is introduced for slope stability analysis including adverse impact of blasting vibrations. The material strength within a slope area is randomized in this bi-variate joint probability analysis. To be a completely general engineering method, the new probabilistic approach employs the random variable transformation technique; the Hermite model of the Gaussian transformation function, which transforms the experimental histogram of strength values to the standard Gaussian variables. Because bi-normal joint probability is analyzed on the true probability region projected on the Gaussian transformed variable plane, it is an exact solution of slope stability based on the available sample data. Details of the probabilistic approach are given through a case study on an iron ore mine. The case study demonstrated that the probabilistic approach is effective and simple enough to be a routine engineering practice for slope analysis.

Jan 1, 1984

By J. A. Herbst, T. I. Martinovic, Y. C. Lo

This study was concerned with the application of a computer simulation methodology to optimize the performance of mills grinding iron ore concentrate prior to pelletizing. The methodology involves batch and plant testing, modeling and computer simulation. The analysis of grinding performance was carried out and capacity increases were predicted in the context of detailed population balance models developed for the plant ball mills. Model developnent and plant confirmation were performed using data obtained in a series of batch tests and three plant tests. From experimental data and computer simulation it was found that ball size, percent solids and classification all had a significant effect on mill throughput. Based on the findings of this study, a 12-152 increase in capacity was predicted to be available by a proper combination of ball size charge and optimum percent solids. These predictions have been confirmed by plant tests in which the recommended operating changes have been made.

Jan 1, 1990

WELL known member of the Institute, Henry Krumb, survived the Japanese earthquake and has written a most interesting description of his personal experience to a friend in New York, an extended excerpt from which we publish, by permission, below. Not having been written for publication it has increased value as a human document in its vivid description of personal impressions and sensations in the midst of such a catastrophe. The earthquake was the most terrible experience I have ever passed through. We arrived at Miyanoshita, Friday, Aug. 31, about 6 p.m., having left Yokohama about 2:30 that afternoon by automobile. It was a most beautiful ride, although rather warm, but not unusually so, as it has been uncomfortably hot ever since we arrived in Japan. The first part of this automobile trip was along the old highway from Kyoto to Tokyo, which is lined with fine old pine trees. There are 52 villages along this highway and we saw real Japanese country life: naked children, both boys and girls, and men wearing nothing but gee-strings. The country on either side was intensively cultivated, the green rice fields and lotus ponds making a most beautiful sight. The occasional hills were all re-forested with young pines. In places the road runs close to the ocean beaches. The last part of the trip was up a steep mountain road, cut out of the side of the mountain. On one side of the road, in the gulch below, was a roaring river. The road crosses this river several times. Miyanoshita is beautifully located on the side of a mountain about 400 ft. above this river at an altitude of 1400 ft. The grounds of the hotel are laid out in Japanese style, small lakes with fish, waterfalls and dwarf trees making a very pretty sight. On the morning of Sept. 1, after walking around the garden and the hotel, we went to our room and I started to write up a few notes. Mrs. Krumb was reading a guide book. A few minutes before noon she came over to the table where I was writing and said that it was about lunch time. Just at that moment hell broke loose. It was the first earthquake I have ever experienced and I did not immediately realize what was happening. The building was shaking as a mine office might shake when heavy blasting was going on near by. Mrs. Krumb, having experienced many earthquakes, stepped to the open door between our room and the bathroom and called to me to get out from under the chande-lier. The plaster was commencing to fall and a large wardrobe fell over. I then knew what was happening and ran to the win dow. Before I reached it a large chunk of plaster from the ceiling hit me on the head and cut my forehead and nose. Mrs. Krumb ran for the other window just as the marble mantelpiece and the dresser fell. Without any hesitation, she jumped out of the win-dow and I followed suit out of the other. Luckily neither of us sprained an ankle-we had jumped 8 ft. We started to runaway from the building but had not gone more than 25 ft. when a second shock or rather a continuation of the first became so violent and the ground under our feet was trembling so that it was almost impossible to stand up without holding on to a tree. The ground seemed to have become liquid and rocked violently, it seemed to me in a vertical direction. In some later shocks the movement was more horizontal. About this time Mrs. Krumb saw the blood on my face and commenced to break down, but only for a moment: As soon as she saw it was not serious she was all right and during the following days stood the experiences and hardships as well as the best of them:

Jan 11, 1923

Effective ground control in the gate entries, particularly in the tailgate travelways, is essential for safe longwall mining. Longwall pillars maintain gate entry stability and carry abutment loads. To answer the need for effective longwall pillar design, an empirical method called Analysis of Longwall Pillar Stability (ALPS) was proposed several years ago. Some recent research at the Bureau of Mines has focused on the refinement and verification of the ALPS method. ALPS was originally developed from field studies in which multiple stressmeters were installed in longwall pillars and monitored during mining. Several new field studies have now been incorporated into the ALPS data base. The field measurements have' been used to verify formulas for predicting abutment strength and pillar loads, and to develop an expression for the distribution of the abutment load.

Jan 1, 1989

Of late there have been various papers published on this subject by various authorities, in which certain definite factors influencing slime settlement have been brought forward. As the principles set forth by these writers are of great interest, and have, in most cases, been generally accepted, the author will review them in the hope that by discussion some more knowledge may be brought to bear on many points connected with the subject.The definition of slime at the present time is not a standard one, and varies according to different authorities, some defining slime as ore crushed to such a fineness that it will pass through a screen of standard size, say 150 or 200-mesh, in water (1, 2);others as that part of the finely-crushed material which is in the physical condition which causes it to remain in. suspension in water, and possesses pr?perties which render it almost unleachable (3). Authorities seem divided on this point, but of late American writers seem to prefer the former definition. On the contrary, B L Gardiner describes slime as a mixture of small particles of crushed ore of varying sizes which, when mixed with water, tend...

Jan 1, 1912

By Debbie Marshall

Nickel and cobalt in lateritic ores can be extracted by either a hydrometallurgical or a pyrometallurgical route. The high-iron limonitic fraction of a deposit is best processed' hydrometallurgically while the magnesium-rich transitional and saprolitic fractions are more suited for pyrometallurgical processing. During hydrometallurgical processing, it may be attractive, for economic reasons, to blend the limonitic component with transitional and saprolitic ores, which contain higher nickel levels. However, blending increases the concentration of magnesium in the feed, leading to increased acid demands. The decision on how much ore to process then becomes an economic one. Ore samples with different magnesium contents were prepared for the leach test program by blending limonitic and transitional ores. The ore samples were slurried in seawater and tested in the Falconbridge Hydrometallurgical Pilot Plant. As expected, acid consumption increased with increasing magnesium content of the ore. For target extractions of 95% nickel and 92% cobalt, the required residual free acid concentration increased from 30 g/L at 1.7% magnesium to 50 g/L at 2.7% magnesium. When the magnesium content was raised to 3.8% and 4.6% in subsequent pilot plant testing, the final free acid requirements did not increase beyond what was observed at 2.7% magnesium. Thus, the cut-off ore composition to maximize nickel units and minimize acid requirements is between 1.7- 2.7% magnesium. Keywords: high pressure acid leaching, laterites, magnesium

Jan 1, 2004