Search Documents

By Nicholas Tabor, Norbert Fuegenschuh, Richard Taylor, Jean-Marc Wehrli

The Plymouth Tunnel forms part of the 16-mile long route of the Purple Line Light Rail Project promoted by the Maryland Transit Administration. The tunnel is approximately 1,220 feet in length with a shallow vertical alignment located beneath a residential area. Challenging mixed ground conditions included surficial soils, decomposed Saprolite, and highly weathered to fresh rock requiring the use of the Sequential Excavation Method (SEM) for construction. This paper discusses innovative approaches implemented during construction as well as challenges faced during planning and installation of a spray-applied permanent concrete liner.

Jun 13, 2021

By M. Clair Smith

This report is one of a series describing exploration, development, mining methods, and costs at United States open-pit mines; the Bureau of Mines prepares and publishes them in cooperation with the mining companies. Their purpose is to promote development and conservation of our mineral resources by disseminating technologic information on mining methods and practices at various United States mines. The exploration, development, equipment, and mining of a large, oxidized-copper ore deposit by open-pit methods, the leaching of the ore with sulfuric acid solution, and the recovery of the copper as cement copper are described herein.

Jan 1, 1958

By D J. Gray

The 4 km long Huguenot Toll Tunnel in the Western Cape region of South Africa celebrated its tenth anniversary on 18 March 1998. At present a single (South) bore with bi-directional traffic flow is operational. The North bore was originally excavated but not lined and equipped.The tunnel is fitted with a semi-transverse ventilation system comprising 45/350 kW two speed fresh-air and 1 MW exhaust air fans at each of the portals. These provide ventilation through fresh and exhaust air ducts above the ceiling separated by movable partition doors. Secondary air ducts deliver air at low level. The fan control depends on the levels of CO pollution or visibility measured at six positions along the tunnel.The system performed well during initial tests and under conditions of low traffic volumes. As traffic volumes increased, and user complaints of bad air in the tunnel were received on several occasions, we realised that we had a problem. Tests confirmed that natural airflow within the tunnel induced by prevailing meteorological conditions outside the portals affected the performance of the ventilation system causing a plug of bad air to be trapped at varying positions along the operating tunnel.The control systems in the tunnel are presently being upgraded as described by Gray, Rieckert and Bullock (1998). As part of the retrofit we are implementing a new control strategy for the ventilation system which takes into account the external weather conditions. This paper discusses the 24 month long meteorological data gathering exercise, which is on-going, and explores the philosophies planned for controlling the ventilation system. The correlation between winds external to the tunnel and induced airflow inside the tunnel are examined. The effects of the weather induced airflow on the existing ventilation system are considered and proposals given for taking these effects into account in the new control strategy. These include the implementation of an expert system to predict ambient airflow from prevailing weather conditions, and the use of airflow measurements taken in the uncompleted North bore as a cross-check.The paper highlights the need to take cognisance of external weather conditions when designing tunnel ventilation systems.

Jan 1, 1999

By Robert Hopler

On June 13, 1912, the final decree of dissolution of the DuPont explosives trust was handed down, and the resulting new companies began operating at the beginning of the new year. The property assets granted to (or retained by) the companies were as follows:

Jan 1, 2014

By Robert Horwood, Richard Harvey

The copper stave was a development of the Blast Furnace cooling system intended to utilise the high heat transfer properties of copper within a fully covered shell cooling solution. They were originally conceived as being able to provide a permanent cooling lining for use primarily in the higher heat zones of the Blast Furnace. Despite a large number of campaign successes around the world the everlasting concept has not proven universal, with some plants having suffered issues in two particular areas: stave bending (leading to water leaks at back of the stave) and stave wear (erosion on the hot face). Primetals Technologies have in the past been approached to provide assistance to a number of Blast Furnace operators who were experiencing operational issues with the copper stave furnace cooling systems of others. Through knowledge gained resolving these issues, and with the positive experiences of their own copper stave designs, Primetals Technologies have worked towards developing a new concept in copper stave design capable of providing a more robust solution to cope with the greater productivities of modern ironmaking. This paper will provide an outline to the concepts that have driven the design of this new technology.

Oct 1, 2019

By L. B. Paterson

Mining Engineers throughout the world have an appreciation for the importance of the role of the Blasthole Drill in one of the primary elements of the mining process. This paper highlights areas that could influence the overall cost effectiveness of that process of breaking rock and how equipment is designed and configured to meet that challenge. Factors influencing drill productivity and overall cost effectiveness are addressed, both in the Mine Environment and on the Blasthole Drill.

Jan 1, 1999

"The Companion Policy is guidance and not law. It sets out the views of the Canadian Securities Administrators (CSA) at to the manner in which the CSA interprets and applies certain provisions of NI 43-101 and Form 43101F1. The Companion Policy references the CIM Best Practice Guidelines for Mineral Exploration, and the Mineral Resources and Mineral Reserves, and that they should be followed by Qualified Persons.COMPANION POLICY 43-101CP TO NATIONAL INSTRUMENT 43-101 STANDARDS OF DISCLOSURE FOR MINERAL PROJECTS This companion policy sets out the views of the Canadian Securities Administrators (the “CSA”) as to the manner in which the CSA interprets and applies certain provisions of National Instrument 43-101 and Form 43-101F1 (the “Instrument”), and how the securities regulatory authorities or regulators (the “Securities Regulatory Authorities”) may exercise their discretion in respect of certain applications for exemption from provisions of the Instrument. PART 1 APPLICATION AND TERMINOLOGY 1.1 Supplements Other Requirements – The Instrument supplements other continuous disclosure requirements of securities legislation that apply to reporting issuers in all business sectors. 1.2 Evolving Industry Standards and Modifications to the Instrument- Mining industry practice and professional standards are evolving in Canada and internationally. The Securities Regulatory Authorities will monitor developments in these fields and will solicit and consider recommendations from their staff and external advisers as to whether modifications to the Instrument are appropriate. 1.3 Application of the Instrument -The definition of “disclosure” under the Instrument includes oral and written disclosure. The Instrument establishes standards for disclosure of scientific and technical information regarding mineral projects and requires that the disclosure be based on a technical report or other information prepared byor under the supervision of a qualified person. The Instrument does not apply to disclosure concerning petroleum, natural gas, bituminous sands or shales, groundwater, coal bed methane or other substances that do not fall within the meaning of the term “mineral project” in section 1.1 of the Instrument. 1.4 Mineral Resources and Mineral Reserves Definitions - The Instrument incorporates by reference the definitions and categories of mineral resources and mineral reserves as set out in the Canadian Institute of Mining, Metallurgy and Petroleum (the “CIM”) Definition Standards on Mineral Resources and Mineral Reserves (the “CIM Definition Standards”) adopted by the CIM Council on November 14, 2004, as amended. 1.5 Best Practices Guidelines for Mineral Resources and Mineral Reserves - A qualified person classifying a mineral deposit as a mineral resource or mineral reserve should follow the CIM Estimation of Mineral Resources and Mineral Reserves Best Practice Guidelines adopted by CIM on November 23, 2003, as amended. These guidelines are posted on www.cim.org."

Jan 1, 2003

By III Basham

As environmental laws and regulations become more complex and the economic cost of non-compliance becomes greater, periodic assessment of environmental compliance, identification of potential liability and implementation of any necessary remedial action should be a standard part of the operational methods of any successful business. The title of this paper "Environmental Audits, A Shield, A Sword or A Trojan Horse?" is intended to draw attention to the fact that environmental audits can be used positively to shield a business operations from actual or potential environmental liability; can be used proactively as a 'sword" in both a marketing context ("do business with us because we conduct our business safely and professionally?) and as a mechanism for developing positive relationships with environmental regulators; and, used negatively, as a "Trojan horse", by developing information which those same environmental regulators (or the public) use in an enforcement context against your business or that of your clients. This paper will discuss the concept of environmental audits in general; the pros and cons of conducting the same; and the role of the attorney, as part of the "audit" team, to insure, to the greatest extent possible, that the audit process is productive from both a managerial and legal perspective.

Jan 1, 1992

By P. D. Lafleur

A concerted effort to determine the quantities and effects of trace elements in the environment requires the application of a number of different analytical techniques in the same or in different laboratories. The interpretation of analytical data is often difficult because of differing results between analysts or even by the same analyst at different times. Standard Reference Materials (SRM), which are certified for their trace element content and are in a matrix similar to the one of interest, can greatly increase the accuracy of analysis and the reproducibility between laboratories. The United States National Bureau of Standards (NBS) has developed a number of SRMs applicable to the determination of trace elements in environmental materials. Two of these, SRM-1571, Orchard Leaves, and SRM-1577. Bovine Liver, are excellent for biological tissue analyses. Several new standards are of value for fossil-fuel analyses. These are: SRM-1632. Trace Elements in Coal; SM-1633, Trace Elements in Fly Ash; SM-1634, Trace Elements in Residual Fuel Oil: and SRM-1635, Trace Elements in Gasoline. In cooperation with the US Environmental Protection Agency, the NBS has recently concluded an interlaboratory comparison involving analyses by more than 60 laboratories on these fossil-fuel materials. The resulu of this intercomparison and the broad range experience with the biological materials will be presented showing both intratechnique and intertechnique variations, and the sensitivities and comparisons with the values certified by NBS.

Jan 1, 1975

By R. W. Van Dolah

An attempt has been made in this investigation to define the conditions under which ammonium nitrate (AN) might detonate as a result of involvement in fire. The initiation of detonation by shocks derived from explosives or from projectile impact was investigated as a function of temperature and charge diameter. A new technique was devised to investigate the burning of raw and contaminated AN under pressure. No transition, to detonation in AN was obtained in the burning experiments. The critical diameter for detonation of fertilizer-grade AN was found to be quite small when the AN was at temperatures just below melting point; this indicates that initiation of detonation may be less difficult at elevated temperatures but such initiation by gas-phase detonation was shown to be unlikely. Transition from burning to detonation was obtained with AN intimately mixed with fuels that included polyethyl-ene, paper, and fuel oil when these were contained in vessels with restricted vents. However, the experimental results supported by an analytical study indicate that the initiation of detonation in AN from fire exposure in normal storage and from transportation incidents is quite improbable. The detonation of AN in recent incidents more likely may have resulted from the effects of adjacent explosions.

Jan 1, 1966

By J. Starwood

Post-super-cycle mining executives must exploit every aspect of the value chain to deliver continued value to stakeholders. Integrating enterprise-wide information technology with value-chain-wide operational technology, known as IT-OT integration, is essential to extracting optimal results from the value chain. Mining companies trail other industries with respect to IT-OT integration across the value chain. Manual data consolidation and value chain optimization using spreadsheets and human intelligence are widespread practices within the industry. Increasing automation with smart devices and controllers means the volume and velocity of data will soon increase beyond human abilities. Enterprise Architecture provides a method for aligning information technology with the business operating model to successfully implement IT-OT integration. A Value Realization Framework (VRF) provides a means for predictable traceable value realization from IT investments and assets. With these principles, frameworks, models, methods, and techniques, mining organizations can accomplish IT-OT integration that provides their executives with a strategic value-chain-aligned platform for sustained value realization over the long term.

Feb 23, 2014

By Herbert R. Babitzke

The Minerals Availability System (MAS) was formally established by the Bureau of Mines in May 1975 to provide current appraisals of the engineering and economic availability of nonfuel minerals for consideration in the formulation of both domestic and foreign minerals policy, Domes- tic mineral property reports are developed by the Bureau's four Field Operations Centers, and foreign data are obtained under contract. This site-specific information is subsequently subjected to engineering verification and economic evaluation, and the results are analyzed and published as Minerals Availability System Appraisals. The deposit-specific data are also entered into the computerized MAS data base, where a subset of this information, the Mineral Industry Location System (MILS), is available to the public in the form of computer graphics and listings. Other MAS products are also described. The Bureau's MAS personnel are frequently involved in special engineering and mineral economic projects for other Federal and State agencies. MAS personnel also work closely with the private sector, both in the area of mining and processing cost estimation, and as a source of nonproprietary mineral deposit information.

Jan 1, 1982

By Dale T. Peters

Conductivity, both electrical and thermal, are attributes accounting for about 70% of the applications of copper and its alloys. This paper presents results of on-going research into two new applications that depend on copper's excellent conductivity. The Copper Development Association (CDA), together with materials and motor company partners, is working toward a solution to the key problem preventing pressure die casting copper for the conductor bar/end ring structure of the induction motor rotor, i.e., lack of a durable high-temperature mold material. Work is showing that a combination of high- temperature materials and elevated temperature processing gives much improved mold life compared to die steels. Substitution of copper for aluminum in the rotor can result in a 20% decrease in electrical losses in motors consuming 35% of electrical power generated in the U.S. The second development uses the excellent thermal conductivity of several high-strength high-copper alloys to simultaneously improve productivity and part quality in the injection molding of plastic parts.

Jan 1, 1999

By J. R. Dawson, A. B. Kinzel

THE purpose of testing is to determine whether the material in question is identical in all essential respects with similar material which has given satisfactory service. The most common method of securing such information is to select samples as representative of the entire material and subject them to destructive tests. As the welding industry grew, service data were accumulated and tests of welds took on new significance. New tests were devised and old tests modified so as to be more pertinent to welding. Moreover, in some cases the generally accepted procedure of testing by sampling is not accorded the same degree of confidence when applied to welds as in the usual applications. Thus, in instances where great hazard would be involved should the material fail, means of non-destructive testing have been sought with favorable results. Accordingly, tests used today may be divided into two groups, destructive and non-destructive tests.

Jan 1, 1930

By A. R. Taylor

This report describes the design, construction, and operation of a low temperature adiabatic calorimeter for measuring heat capacities of solids or liquids from 60° to 300° K. A brief discussion of the basic theory involved in chemical thermodynamics and the problems involved in obtaining accurate experimental data is presented. The operation of the calorimeter was tested by measuring the heat capacity of a sample of benzoic acid obtained from the National Bureau of Standards over a temperature range of 60° to 300° K. The measured heat capacity values of the benzoic acid compared favorably with similar values obtained by the Bureau of Standards, the maximum deviation being 0.5 percent. THEORY A brief discussion of the basic theory involved in chemical thermodynamics will illustrate the applications of heat capacity data and the problems involved in obtaining accurate experimental data.

Jan 1, 1962

By Robert C. Bacon

The first commercial installation of the Dashaveyor has recently been completed at the White Pine Mine in Northern Michigan. After four years of development work, including prototype testing, and pilot plant operation, this new and unique system is being tested under operational conditions. Many of you may be familiar with the concept through numerous articles which have appeared in the technical press. But this discussion of the system will be simplified and less time consuming with the presentation of a portion of a film showing the Dashaveyor in actual operation. After the movie, I will show some slides which will supplement and clarify it and hopefully lay the basis for questions you will undoubtedly wish to ask.

Jan 1, 1968

By Jeffrey H. Welsh

This report presents a study on the use of computerized, continuous remote monitoring systems for fire and explosive atmosphere safety in underground coal mines. The effects of these systems on the safety level in mines are investigated, and the relationship between mine safety regulations and computerized, continuous, remote monitoring is analyzed.

Jan 1, 1982

By Manuel S. Rivera

Abstract. Instrumentation in concentrators has evolved from a few isolated indicators to compu- terized control within twenty years. This evo- lution has caused a drastic change in the phil- osophy, personnel and equipment used in a pro- gram of servicing and utilization of present day automation.

Jan 1, 1980

By James A. Morgan

FIELD MEASUREMENTS OF NOISE WERE MADE ON THE PERIPHERY OF ENCLOSURES DESIGNED, MANUFACTURED AND INSTALLED BY INDUSTRIAL ACOUSTICS COMPANY, INC. ON THE SECONDARY TACONITE CRUSHER AT THE JACKSON COUNTY IRON COMPANY PLANT IN BLACK RIVER FALLS, WISCONSIN. NOISE REDUCTION ACHIEVED BY THE ENCLOSURES WAS SUFPICIENT TO PERMIT REDUCTION OF CRUSHER ROOM NOISE TO 90 DBA, PROVIDED THAT OTHER SOURCES ARE APPROPRIATELY TREATED AND ACOUSTICAL ABSORPTION IS PROVIDED IN THE CRUSHER ROOM. SECONDARY CRUSHER NOISE WAS REDUCED 10 TO 15 DBA BY THE ENCLOSURES.

Jan 1, 1980

By A. F. Matheson

The St. John Del Rey Mining Company, Limited, is an English company owning 150 square miles -of mining lands near Belo Horizonte, Minas Geraes, Brazil. The area is 2,300 to 5,000 feet above sea level, with a pleasant and healthy climate. Bedrock is Precambrian. The Nova Lima series of metamorphosed sediments and some volcanics is overlain uncomfortably by the Minas series of quartzites, itabirites. etc. Batholithic granite and gneiss cut both series and basic dykes cut all these rocks. There are important deposits of gold, iron, and manganese on the Company's holdings, as well as occurrences of arsenic, antimony, cobalt, nickel, dolomite, day, quartz, -ochre, bauxite, kyanite, and asbestos. Except for gold and consequent recovery of arsenic, all the other materials are relatively unexploited. The Company operates the Morro Velho gold mine and the Espirito Santo and Raposos gold mine. The Morro Velho mine was purchased in 1834 for £56,000. To the end of 1952 it had produced 7,000,000 troy ounces of gold from 15,000,000 short tons of ore. The ore z?ones are replacement deposits in a sinuous siliceous dolomitic rock locally termed "lapa seca," and plunge east, near surface at 45 °, at 8,000 feet at 15°. The ore minerals are pyrrhotite, arsenopyrite, pyrite, and chalcopyrite. Gold is finely distributed and almost nowhere visible. Ore reserves at the end of 1952 were estimated at 5.5 million short tons grading 0.39 oz. gold per ton. Chances exist for new ore within the mine area. The Espirito Santo and Reposos mine, in folded banded iron formation, has mineralization similar to Morro Velho but sulphides are less abundant. The mine to a depth of 2,500 feet has estimated ore reserves of 1.5 million tons of an average grade of 0.28 oz. gold per ton. New ore may be expected both laterally and at depth. To the end -of 1952, the ?Company had paid dividends of almost £4,- 600,000, largely earned from the operation of the gold mines.

Jan 1, 1956