Search Documents

By Wu Tao, Lu Shijie, Xia Xiaoou, Zhang Ming

The impeller and stator are the most important components that can significantly influence the performance of flotation cells directly. The performance of the impeller and stator of KYF flotation cell is revealed by CFD (Computational Fluid Dynamic) simulation in this paper. A method of obtaining the circulation volume is proposed. The circulation volume is proportional to third power of impeller diameter. And the circulation volume increases linearly with the increasing of the speed. CFD simulation can draw the conclusions that there is a proportional relationship between power consumption, third power of speed and fifth power of impeller diameter. CFD prediction results agree with the theoretical formula. The difference between the forward and backward impeller is analysed in the paper. The circulation volume of the backward impeller is obviously larger than that of the forward impeller under the same condition, but power consumption of the backward impeller is lower. It is demonstrated that the impeller and stator system of KYF flotation cell is an efficient and reasonable stirring mechanism. CFD simulation could be reliably used in flotation cell design and optimization.

Jan 1, 2014

By R. Newman

An inexpensive slow-speed data acquisition system has been adapted to digitally record multiple parameters simultaneously at intervals of 15 seconds. The system was built for use with standard soils testing equipment to automatically record load and displacement parameters at predetermined instants in time. Simultaneous readout is achieved by the use of special signal conditioner and sample-and-hold circuits which read the multiple signals simultaneously and hold them until the slow acting system can print out. Three channels of a 10-channel system have been converted and found to operate successfully during a series of direct shear tests. A unique feature of the system, which significantly reduced its cost, is the power supply units. Dummy circuits are used to maintain a constant power demand during sampling) thus eliminating the need for a costly power supply with rapid response characteristics. The entire system, having an overall accuracy of 0.25 percent, was put in operation for a cost under $2,500.

Jan 1, 1970

By Jie Ma, Shun-Li Zhao, Jian Zhao, Jie-Yu Zhang

"Microstructural morphology evolution of Ni-45wt.%Mo droplets during rapid solidification process was investigated using an advanced modified 3D cellular automaton-finite element(CAFE) model by CALCOSOFT software. The model was modified by User-defined functions (UDFs) and validated with experimental solidification microstructural morphology of Ni-45wt.%Mo droplets available in the literature. Then, the influences of convection heat transfer coefficient, superheat of the alloy droplets and droplets size were investigated during the rapid solidification process. The predictions show that microstructural morphology is obviously sensitive to convection heat transfer coefficient and droplet size. With the decrease of convection heat transfer coefficient, the grain density decreases. In addition, the decrease of the droplet size could obtain refined microstructure. However, decrease the superheat ofNi-45wt.%Mo droplets has little effect on microstructural morphology.IntroductionFor several decades, much attention has been paid to undercooled alloy droplets of rapid solidification process for which can obtain refined microstructure, decreased microsegregation and extended solubility of alloying elements [1-3]. Extensive prior work shows that solidification of droplets plays an essential role in advanced material properties [ 4]. Consequently, it is very important to investigate the microstructural morphology evolution, especially for dendrite growth during non-equilibrium solidification process, for dendrite growth reflected the kinetics of the crystal growth process."

Jan 1, 2013

By T. P. Meloy

Traditionally the mineral and mining engineers have characterized particles by sieving and-settling. Within the last decade, with the advent of the scanning microscope, entirely new experimental and theoretical approachesl-10/have been taken to minutely define the particle surface. This approach depends upon a hypothesis which takes advantage of the recent developments in automatic micro-scopes which can acquire large amounts of information in a short time and the new computational techniques which rapidly reduce the information to meaningful, practical data. Historically sieving and settling are the oldest sizing techniques known. Sieving by square screens, shown on Figure l-A is a common, current practice for sizing particles both in the laboratory and in production. A woven cloth is used which usually has square openings. The size particle that will pass through the opening dependent on a complex relationship of its morphology. As can be seen in Figure l-A, neither the width nor the height of the particle is determined by sieving. From square screens one and only one parameter characterizing the particle size is obtained, that parameter is the radius of the sphere that will just pass through the given sieve opening. A variation of square mesh screen is the slot screens, shown in Figure 1-B. Here another measure more closely associated with the height of the particle is obtained. Once again, one and only one parameter is associated with the particles' shape.

Jan 1, 1977

By Thomas S. Mackey

The industrial types, sources, and quantities of USA tin residues are identified and the methods of treatment reviewed. The effect of a lower tin price, due to a current major world surplus of tin metal, is mentioned and covered in some detail. The names and locations of over 100 USA firms recovering tin residues are listed. Current smelting and refining charges are included to convert the residues into tin metal and alloy. The impact of the suspension of the LME daily tin price since October 24, 1985 to date, and the failure of the International Tin Council to support the Buffer Stock Manager are reported with comments.

Jan 1, 1986

By Mateus Luiz Gamba

O titânio e suas ligas são aplicados em grande escala em implantes ósseos por apresentarem excelentes resultados de biocompatibilidade. No entanto, ainda não existe um consenso na literatura com relação à influência das características morfológicas destes implantes na osseointegração, principalmente na definição da melhor rugosidade e energia superficial. Vários trabalhos têm sido realizados com o intuito de comparar diferentes tratamentos superficiais empregados para otimizar a adesão, o crescimento e a proliferação celular. O presente trabalho tem como objetivo apresentar uma base de dados sobre características superfícies versus osseointegração para experimentos de biocompatibilidade realizados in vitro. Foram feitas coletas e análise de dados qualitativos usando métodos analíticos em artigos científicos publicados em periódicos internacionais, sendo considerados na pesquisa artigos que utilizaram superfícies de Ti/TiO2 e células osteoblásticas. Os principais atributos definidos para a base de dados foram rugosidade, tamanho da célula, energia da superfície e/ou ângulo de contato, tipo de tratamento superficial, viabilidade e a resposta observada na cultura celular. Espera-se que esse artigo contribua para que futuros trabalhos possam utilizar métodos e estudos que permitam auxiliar na descoberta de conhecimento através de padrões que acelerem o processo de osseointegração impactando diretamente na recuperação do paciente implantado e na sua qualidade de vida.

Aug 8, 2018

By O. P. Chisholm

The most noticeable change in lead smelting over the past few years has been the increase in the smelting rate of lead blast furnaces. For several years a great deal of attention has been paid to the preparation of the blast-furnace sinter charge but more recently the plan has been to incorporate- almost the entire makeup of the blast-furnace charge, excepting coke and scrap iron, at the sintering machines. Formerly, sintering machines were used primarily for removing, sulphur and for agglomerating finely divided material both sulphide and oxide in character. Limestone flux usually was so proportioned that a relatively large amount was added to the furnace charge direct. This procedure was also followed with oxidized ores, which were purposely crushed coarse' so that they would be adaptable for direct smelting on the furnace charge. In later years it has been the tendency in western smelters to include practically all of the limestone and oxidized ores in the sinter charge. This has been somewhat more costly because fine crushing is required for sintering purposes and because these oxidized materials were given additional processing through the sinter plant. The addition of such oxidized materials to the usual charge to be sintered, brought about, in certain instances, a deficiency in heat ordinarily supplied by the sulphide constituents of the charge. This heat deficiency has been remedied by the addition of carbonaceous fuel, in the form of finely crushed coke breeze, or in a few instances by the addition of zinc retort-plant residues. The enhanced gold price has stimulated the mining of crude siliceous ores throughout the Western States and in the smelting of such ores more limestone is required for fluxing. Shipments of gold-bearing pyritic concentrates to Western smelters have increased, and the combination of increased silica, limestone and pyrite has increased the percentage of slag, which, in itself, is an aid in .securing smoother and more rapid smelting in the blast furnace. By the addition of these substances, the percentage of zinc in the slag has been appreciably lowered. at many plants, with resultant benefit to smelting speed at the blast furnace. This increase in slag formation with lowered zinc content has caused also perceptible lessening of the amount of lead on the charge and this has benefited the blast-furnace smelting. Although a satisfactory sinter is fundamental in increased rate of bullion production per furnace, there has been a trend over the list four or five years to decrease the percentage of coke and increase the percentage of scrap iron and limestone on the blast-furnace charge. As a result of these changes in practice certain blast furnaces, without any mechanical change, have doubled or tripled their tonnages. For furnaces whore the volume of air is recorded, records show decidedly larger air volumes with a comparatively small increase in air, pressure, or, none at all.

Jan 1, 1941

By A. P. Grippo, L. B. Phelps

Many coal mining companies have potential surface mine reserves that either are known or suspected to have had prior drift mining activity on them. In many cases, there is no documentation on these mines or, at best, very fragmented records. These undocumented abandoned underground mines are creating engineering, financial, and environmental difficulties and concerns for both surface coal mine operators and regulatory personnel. This paper examines the use of resistivity techniques in detecting entries of abandoned drift coal mines. The detection of such a drift mine entry would confirm the presence and orientation of an abandoned underground coal mine.

Jan 1, 1987

By C. F. Meyer

The recirculation of mine air in an underground colliery, has always been regarded as a hazardous practice in South African collieries. The Mines and Works Act and Regulations states that fresh air, flowing Into an underground section, must flow out directly into the return airways after being utilized once in the section. One of the largest producing underground collieries in South Africa, Initiated a project on controlled recirculation with the permission of the South African Government Mining Engineer. The project involves the recirculation of 65 m3/s of air inside a ventilation district which serves a total of six production areas. The aim of the project was to increase the airflow to the sections without altering the existing ventilation system. Tracer gas studies were carried out to determine the actual distribution of the recirculated air to the individual areas. The results showed that an effective 54,18 m3/s of the recirculated 65 m3/s reaches the sections. This gives an air utilization figure of 83,4 per cent. Dust surveys were also carried out as part of the project to determine the effect of the recirculation of the return air on airborne dust levels. The results showed that the dust levels remained constant in the main intake and return airways and that no hazardous situation was being created. The project proved to be successful and showed that controlled recirculation can be executed and used as a solution for the supply of air to sections without endangering any lives.

Jan 1, 1993

By C. Marais

The use of machine vision in the monitoring and control of metallurgical plants has become a very attractive option in the last decade, especially since computing power has increased drastically in the last few years. The use of cameras as a non-intrusive measurement mechanism not only holds the promise of uncomplicated sampling but could provide more consistent monitoring, as well as assistance in decision making and operator and metallurgist training. Although the very first applications of machine vision were in the platinum industry, no automated process control has been developed for platinum group metals (PGMs) as yet. One of the reasons is that to date froth features could not be related to key performance indicators, such as froth grade and recovery. A series of laboratory experiments was conducted on a laboratory-scale platinum froth flotation cell in an effort to determine the relationship between the platinum grade and a combined set of image features and process conditions. A fractional factorial design of experiments was conducted, investigating 6 process conditions, namely air flow rate (x1), pulp level (x2), collector dosage (x3), activator dosage (x4), frother dosage (x5) and depressant dosage(x6), each at levels. Videos were recorded and analysed to extract 20 texture features from each image. By using artificial neural networks (ANN), the nonlinear relationship between the image variables and process conditions and the froth flotation grades could be established. Positive results indicate that the addition of image features to process conditions could be used as sufficient input into advanced model based control systems for flotation plants. Keywords Flotation, machine vision, image analysis, neural networks.

Jan 1, 2011

By Akira Usui

Platinum is one of the most rare elements in the earth?s crust, but it is significantly enriched in some hydrogenetic ferromanganese crusts in the ocean. The element is essential to the electric industry and is believed to be of importance as a raw material a future fuel-cell industry. The earlier reliable chemical analysis of platinum-group elements (PGE) of ferromanganese crusts have indicated a variety of concentrations of Pt in the range of 100 ppb to a maximum of about 1 ppm, but little is known about the elemental abundance in ferromanganese crusts on fine-scale, or the geochemical behavior and form of the element. The chemical and mineralogical forms of platinum and its group are important in planning the methods of mineral exploration and extraction of the elements from of ferromanganese crusts. We attempted to characterize the distribution pattern within a cobalt-rich crust on the fine to microscopic scales by using reflecting microscope, scanning electron microscope/energy-dispersive spectroscopy, electron microprobe X-ray analysis (EPMA), ICP-mass spectroscopy, X-ray absorption near edge structure (XANES), small-focus XRF, and X-ray diffraction (XRD). These data indicated a wide range of Pt concentration from 150 to 700 ppb within a crust, though we found no distinct inter-element correlation or mineralogical control. Under the reflecting and electron microscope, no distinct Pt-bearing minerals or particles were identified. Small-focus XRF indicated no uneven distribution in any particulate matter, but all areas are less in abundance than the detection limit of about 10 ppm. Our tentative conclusion is that zero valence Pt0 (as suggested by XANES) is dispersed in the form of submicroscopic material most probably within ferromanganese minerals, and therefore, Pt-rich mineral particles may not be a major carrying phase.

Jan 1, 2005

By P Mulvey, M Stuckey

"Inter-aquifer leakage due to fractures caused by coal seam gas extractions or longwall mining is an important issue for both the gas and coal industries. Currently, predicting stress induced macro-porosity associated with hydraulic fracturing, depressurisation via dewatering or collapse of overlying seams to infill a void left by longwall mining, is problematic. If fractures can be located the fracture can be sealed. Locating fractures is difficult. The non-geophysical approaches to locate fractures has been to consider the mixing of different waters, particularly that of more recent shallower groundwater with older deeper groundwater, via differences in radio-isotopes integrated with geochemical models to predict likely mixing of waters. This approach is applicable under appropriately complex settings; however, it is an expensive technique and is based on the assumption that the daughter isotopes are equally non-reactive which may not always be the case.Potentially a cheaper and faster technique is to consider integrating geochemistry (mineral weathering) and hydrogeology. The chemistry of groundwater, controlled by the weathering of primary rock?minerals and?formation of secondary minerals, can not only be differentiated between geological strata but also within strata as different stages in weathering results in differing impacts on water quality (ie different reactants).Field analysis of pH, electrolytic conductivity (EC), oxidation reduction potential (ORP) and dissolved carbon dioxide together with laboratory analysis of dissolved constituents characterise the chemistry of the water. Collection of rock samples at the time of drilling for bore installation can provide the (only) opportunity to assess the media in which the groundwater resides and migrates through. An assessment of aquifer matrix chemical makeup, via bulk sample chemical analysis, X-ray diffraction (XRD) and petrographic analysis can achieve this.The chemistry of groundwater is dependent on the water velocity. Water at deposition and post-diagenesis dissolution of minerals by hydrolysis and oxidation will result in equilibria of the dissolved phase with the solid phase. Post-depositional fractures caused by either tectonic activity or weathering alter the rate of weathering and thereby the geochemistry. Slow water flow in microfractures results in water in equilibrium with the rock minerals. Faster flow in larger fractures results in water being in disequilibria with rock minerals.Fractures can alter groundwater chemistry by two pathways: changing groundwater velocity, which changes the rate of hydrolysis or oxidation mixing water from different geological strata.Both pathways cause subtle changes in the water chemistry.It is however, the dissolved phase chemical data, which can be observed over time at individual locations and/or at a point in time along a flow path, which allows the hydrogeologist to ælook up-gradientÆ and locate the zone of leakage. Hence, influences on rock/groundwater chemistry, from anthropogenic sources to natural mixing of waters, can be assessed via appropriate interpretation of geochemistry, hydrogeochemistry and flow data.This paper will use the example of the geochemical and hydrogeological characterisation of aquifers within the Hawkesbury and Bulgo Sandstone of the Southern Coalfields to the south of Sydney in New South Wales to demonstrate this approach.CITATION:Stuckey, M and Mulvey, P, 2013. Looking for fractures - integrating geochemistry with hydrogeology to find inter-aquifer leakage above dewatered or collapsed coal seams, in Proceedings Water in Mining 2013, pp 99-108 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 26, 2013

By J. P. Denny

The constitution of the Ga-In system was determined by thermal methods. An experimentally determined metastable equilibrium line (an extension of the indium-rich liquidus) was obtained. The various alloys were studied metallographically using polished samples obtained by a casting method. These low melting alloys required a special dry-ice assembly to maintain a suitable temperature. RECENT interest in alloys that are liquid at room temperature has led to rather extensive investigation of gallium-base alloys. Widely distributed over the earth, gallium could be produced in substantially larger quantities than at present, if a significant demand existed.' One study' has established its presence in 12 out of 14 zinc blends, in all of 15 aluminum ores, in 4 out of 12 manganese ores, in 35 out of 91 iron ores, and in all of 7 magnetite ores. It occurs as a rule in minute amounts, however, leading to high extraction costs. Recent quotations run from $2.50 to $7.50 per g. During the course of the present investigation, portions of the system Ga-In have been redeter-mined, and the results of this study are presented herein. Thermal and metallographic methods have been employed. Lecoq de Boisbaudran, the discoverer of gallium, conducted the first investigation" on Ga-In alloys in 1885. The temperatures of incipient melting, and of completion of melting, were determined at four alloy compositions. In 1936, Hansen' constructed a eutec-tic-type phase diagram for the system Ga-In, based on . work. The existence of a Ga-In compound was regarded as improbable by Hansen, and subsequent investigations are in agreement. French, Saunders, and Ingle3 conducted a more complete study of the system in 1938, using thermal methods. Their phase diagram is a eutectic type, containing a unique concave-upward liquidus. The solid-solution range of gallium in indium was reported as 9.5 pct by weight, and that of indium as less than 1 pct, at the eutectic temperature. The eutectic composition, determined as being bracketed by the compositions showing a true horizontal at the eutectic temperature (16°C), was reported as 76 5-0.5 pct Ga and 24 i 0.5 pct In. Experimental Procedure The preparation of Ga-In alloys is simplified by the low melting points involved. Various compositions were prepared by melting in pyrex tubes, using a cover of distilled water or parafin to prevent the alloys from wetting the glass wall. In all cases, the melts were homogenized. by stirring. Where possible, both cooling and melting curves were determined. The extensive undercooling of gallium was found to prohibit a satisfactory cooling-curve analysis of gallium-rich alloys, however, and transition points on the gallium side of the eutectic could be determined only by melting curves. The inverse rate method of thermal analysis proved to be most satisfactory and was used to a great extent. Various heating and cooling rates were used, ranging from 0.2" to 5.0°C per min. Low temperature melting analyses were conducted within a constant temperature bath, maintained at about 70 °C. The alloys were solidified (under water or paraffin) within a pyrex tube, using dry ice; the tube was then sealed within a cold Dewar flask, the unit transferred into the constant temperature bath, and periodic temperature readings taken. The high temperature melting-curve determinations and all cooling-curve determinations were made in a vertical tube furnace. At near-eutectic compositions, the furnace was placed within a refrigerated room held at —20°C. Accordingly, the furnace on cooling approached —20°C asymptotically and permitted the determination of those phase transitions occurring below room temperatures. Temperatures were measured with a 30-gage iron-constantan thermocouple, immersed directly in the alloy. To prevent contamination of the melt, the leads and junction were coated with Lucite, applied by painting with a solution of Lucite in ethylene dichloride. Electromotive force measurements were made with a Leeds and Northrup precision potentiometer, type 8662. The couples were calibrated against the boiling point. of water and, at lower temperatures, against a calorimeter thermometer having a Bureau of Standards certificate. The melting points of gallium and indium used in the present investigation were determined as 29.-77° and 156.1°C, in good agreement with previously reported values of 29.78°C° and 156.4"C.' The spec-

Jan 1, 1953

By M. Ahrens, J. Gonser

Gearless mill drives are a well established solution for grinding applications in the minerals and mining industries. The paper describes the functionality and technical features of such drive systems as well as their advantages compared to other drive solutions. Due to the variable speed operation the grinding process can be optimized for ores with varying grinding properties. This leads to significant optimization potential for the plant design as well as for its operation. Furthermore, energy and cost savings due to optimized operation, high system efficiency and high system availability are shown.

Jan 1, 2007

By A. Lucian Walker

SILVER is not only of paramount importance to millions of people as a medium of savings and to other millions as a medium of exchange, but it is also valuable and useful in industry. Mexico continues to be the largest producer of this metal, followed by the United States, Canada, and Peru. The largest consumers are China and India, which normally absorb about two-thirds of the world's mine production, hoarding it as savings. The imports by these countries exert a powerful influence upon the price, yet neither country is on the silver standard. China having abandoned it in 1935 and India in 1893, when the rupee was definitely linked to the pound sterling. Other nations such as Persia, Ethiopia, Mexico, and many of the South American countries either have been on the silver standard or have used silver as their chief circulating medium, and most large nations use it for subsidiary coins, this use accounting for 20 to 30 million ounces annually. The arts and industries have consumed 35 to 40 million ounces each year.

Jan 1, 1937

By P. B. Queneau

An operating problem encountered at the Moa Bay operation in Cuba, where nickeliferous laterite ore is processed by sulfuric acid pressure leaching, is the formation of alunite and hematite deposits on the autoclave walls. The AMPX Extractive Research & Development, Inc., metallurgical laboratory (Golden, Colorado) has made substantial improvements in the Moa Bay process in the areas of metal recovery, energy consumption, and feed versatility. One of the advantages of AMAX's process is its ability to treat substantial portions of nickel- and magnesium-rich serpentine while maintaining acid utilization efficiency. The process minimizes scale formation by combining staged acid addition with vigorous agitation and 270°C operation, but does not eliminate scaling. This paper describes how advantage can be taken of MgSO4?XH20 precipitation both to inhibit alunite scaling and to disperse hematite scale within the MgSO4?XH20 matrix. Cooling the autoclave from its 270°C operating temperature down to 180°C takes advantage of the reverse solubility of magnesium sulfate. The magnesium dissolves, liberating entrained hematite, thus providing a means for control of autoclave scale with minimum process disruption.

Jan 1, 1984

By Bruce Kennedy, Charles Bruce

MINERAL EXPLORATION 'The Function of Exploration Mineral exploration aims at locating the presence of economic deposits and establishing their nature, shape, and grade. As all ore bodies are finite, exploration is essentially the lifeblood of the mining industry. It is divided into two phases, reconnaissance and target investigation. It involves geological mapping, geophysical prospecting (aerial and ground or both), geochemical surveys, prospect drilling, and/or exploratory under-ground workings. Successful exploration is followed by development drilling, mine development, and eventually operation. In underground mining, the term "ore" is applied rather loosely to metalliferous rock that can be profit- ably mined, but nonmetallic industrial minerals and energy related materials constitute a large and growing portion of the tonnage extracted by underground methods each year. It is appropriate, therefore, to consider exploration as the search for any useful substance occurring in the earth or in the oceans that is of sufficient value as to volume, grade, chemical and physical com- position, and location as to make extraction by mining commercially profitable for the investment required. The Selection Process The search for ore includes hundreds of mineral commodities. The more successful exploration organizations tend to restrict the search to the mineral commodities for which they have strong exploration expertise and which have a high probability of being concentrated in areas open to exploration and development in sufficient volume, grade, and proximity to the surface to warrant the large expenditures of risk capital in finding an ore body. Special expertise is needed to engage in mineral exploration and development for the extended periods required for success. Individual prospectors continue to discover mineral occurrences, but it generally takes an organization with strong financial resources to carry the exploration process forward to the point of developing "ore." Still greater corporate resources in the form of management, engineering, and sales capability are needed to develop an ore body into an operating mine. In the past, companies other than those engaged in mining rarely conducted exploration, since they lacked the technical skills and know-how to bring a mine to fruition. A notable trend in recent years has been the success of other resource-oriented firms, such as petroleum companies, that have not only acquired the necessary skills to engage in exploration for hard minerals, but are doing so on a far more intensive scale than known in the industry heretofore. The desire to diversify from increasingly regulated oil and gas, the potential for the discovery of a bonanza, and the large scale of mining projects for these capital-intensive firms are the attractions. US government and certain international organizations, such as the United Nations, have fielded sizable exploration programs in the past decade on behalf of Third World countries wherein many of the world's higher grade deposits and scarce mineral resources are located. The level of overall mineral exploration in the industry is, regrettably, closely geared to the business cycle. Accelerated search during the periods of strong demand, shortages, and high prices, together with the long lead times necessary to develop mineral finds, often creates surges in supply which invariably are followed by a collapse in prices. The trend is, therefore, to exploration funding by larger better-endowed firms having the staying power to weather the cyclical nature of mining. Tax incentives, tariff policies, and other incentives have a decided impact on the level and nature of exploration. Surface mining regulations and environmental forces have fostered a renewed interest in under- ground development despite the lower average costs of surface mining. Spiraling inflation has caused mining costs to outpace prices for many mineral substances. Organizations increasingly are directing their search away from high- grade but limited tonnage occurrences toward low-grade disseminated bulk tonnages amenable to mining on a vast scale. Mining continues, therefore, to grow even more capital-intensive with half-billion-dollar mine-mill- smelter complexes now commonplace, compared with the hundred-million-dollar projects of a decade ago. Reconnaissance Exploration Having elected to search for specific mineral commodities, the exploration company narrows its focus to a reconnaissance of those regions offering the best potential. A working hypothesis which is constantly up- dated concerning the geologic controls for ore occurrence guides the search. The possibilities for discovery are best in areas of existing mines and known ore bodies, where the probabilities are high for additional ore occurrences. In such areas, published data on the trends and geologic controls of known mineral occurrences aid the search. Even in some remote territories, a variety of geologic data is available to the explorationist. The major sources of basic geologic data are the libraries of the US Geological Survey (USGS), the state geological surveys, the American Institute of Mining, Metallurgical, and Petroleum Engineers (AIME), the US Bureau of Mines, and various institutions such as Colorado School of Mines. Overseas, virtually all of the countries have their own geologic survey groups which are associated directly, or indirectly, with their respective ministries of mines. The objective of reconnaissance exploration is to narrow the search by pinpointing target areas having interesting mineralization. These favorable areas are then investigated in detail to delineate potential ore bodies.

Jan 1, 1982

By Raymond L. Lowrie

Deregulation, as authorized by the Energy Policy Act of 1992 (PL102-486) allows free-market competition in the electric-utility industry. As the act unfolds, though, uncertainties abound about the type, degree and direction of impacts throughout the affected economy — from fuel suppliers to electricity generators and from power distributors to energy consumers. Instead of having a familiar base of captive customers and electricity prices fixed by negotiation with state public utility commissions, utility companies are preparing for open, free-market competition. They are looking at all areas, including fuel supply, to cut costs to remain competitive. Humorous anecdotes are told about utility companies shunning insiders for senior executive positions. Instead, they are opting for people from the telephone or other industries with deregulation experience. And there are light-hearted stories about a trend away from traditional electric-company names, such as the name of a city or state followed by Edison or Power and Light, to space-age names, such as Ameren, Entergy, Illinova or Unicom. No one wants to be left behind or be perceived to be left behind.

Jan 1, 1996

By H. W. Gussmann, R. G. Rohrs, E. van der Merwe

Salinity in Effluents carries a high penalty as a result of toxic­ity, corrosion, limited re-use potential, scaling and environmental impact. Although the high TDS, such as Calcium sulfate, other than metals are still being dealt with a low key non issue basis, they are receiving more and more attention from regulators. Traditional solutions to solve these problems are costly and inefficient and create therefore severe constraints on the prof­itability of mining operations and out-price in general the finan­cial resources for environmental clean up operations. Going up the technology versus cost curve the most econom­ic solution to pollution is dilution but which is difficult in a coun­t1y shoti of water. If this can't be done, the second best, at least in sunny areas, is, to pump the whole effluent on a tailings dam for evaporation. Depending on the contaminants, one may have to pond the efflu­ent to avoid re-dissolution and seepage into the ground. The next most common solution to pollution is the addition of lime to remove and concentrate any dissolved metals and then dump the product, hidden in a mass of gypsum in a convenient place. Again ponding may be required to avoid ground pollution. However the treatment costs start to rise steeply if it is not allowed to discharge the limed overflow solution because of its high calcium sulphate content. Further treatment is then required in the form of high cost and high tech membrane process tech­nology such as reverse osmosis or dialysis or even mechanical driven evaporation.

Jan 1, 1998

By Haukka M. T

A new low-dilution fusion method which has been successfully used for accurate determination of the major oxide components of silicate rocks, is applicable to rapid, accurate determination of trace or minor eiements in mineral exploration samples. Limit of detection is in many cases less than 5 ppm. Either rapid, approximate measurement and calculation methods (suitable for geochemical exploration), or more accurate methods (applicable to orebody evaluation studies) may be used.Rapid methods are described for nickel in rocks and sulphides containing 10 ppm to >2 per cent Ni, and for gallium. The rarely-determined element gallium is an example of a constituent which may be easily investigatedby XRF using the LiB02 fusion disc, which is a permanent, easily-stored analytical sample available for later rapid or accurate analyses. The method is applicable to over 30 elements at levels encountered in mineral exploration.

Jan 1, 1978