Search Documents

By R G. Barker, A B. Christie

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. More than 11 Moz of Au and 50 Moz of Ag have been produced from epithermal deposits in New Zealand, almost entirely from 50 deposits in the Hauraki goldfield. Since the 1980s, new deposits have been discovered at Waihi (Favona, Trio, Correnso) and nearby at Golden Cross. Feasibility studies into reopening the Talisman mine at Karangahake are continuing, and advanced projects with preliminary inferred resource estimates are reported at Wharekirauponga, Neavesville and Muirs. In the Taupo Volcanic Zone, 11 prospects have been drilled, resulting in the definition of large but low-grade Au-Ag resources at Ohakuri. In Northland, several Au, Ag and/or Hg prospects are known, and small quantities of Ag and Hg have been mined. Six prospects have had some drilling, with the most advanced exploration at Puhipuhi. The application of Taupo Volcanic Zone geothermal systems research to the modelling of former hydrothermal mineralising processes in some epithermal prospects has enabled better targeting of exploration.CITATION:Christie, A B and Barker, R G, 2015. Exploration for epithermal gold deposits in New Zealand, in Proceedings PACRIM 2015 Congress, pp 533–540 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By E. M. Wise

IN a previous communications the improvement in strength, harden-ability and color, occasioned by replacing gold in a typical gold-silver-copper alloy by various amounts of platinum, or palladium, was discussed. In the present paper the results of further studies upon the constitution and the nature of the hardening transformation in these alloys are pre-sented. This research may be summarized as follows: 1. The liquidus and solidus have been determined for the alloys of the palladium and platinum series. Cooling curves were utilized for deter-mining the liquidus of the palladium alloys but this method proved unsuitable for the platinum alloys so that a, novel quenching method was utilized for the latter. Both the liquidus and solidus of the palladium alloys increase steadily with the palladium content. The liquidus of the platinum alloys increases rapidly with the platinum content, while the solidus temperature increases with the platinum content up to about 14 atomic per cent platinum, but suffers no further increase with additional increments of platinum up to 20 atomic per cent at least, owing to a peritectic reaction. 2. Palladium, and even more effectively platinum, reduces the rate of grain growth. Owing to this fact and to the increase in the solidus temperature, "overheating" does little or no damage to alloys containing reasonable quantities of these elements. This is confirmed both by tensile tests and metallographic examination. 3. The excess phase present in one of the high-platinum-content alloys has been isolated and chemically analyzed and was found to consist almost wholly of platinum, gold, and copper, evidently derived from the compound AuCu, by the partial replacement of gold by platinum.

Jan 1, 1933

By G Gibson

Realising that current roadway development performance levels were unlikely to sustain new generation high-capacity (15 Mt/a) longwall mines then being planned, the Australian Coal Association Research Program (ACARP) established a Roadway Development Task Group (RDTG) in 2005 to develop a research strategy targeted at improving roadway development performance in Australian longwall mines. The initial phase of the project identified a number of factors that differentiated best practice mines from others, and proposed a multi-faceted research strategy encompassing both short- and long-term research initiatives, including:conducting regular benchmarking studies across the industry to identify factors contributing to improved performance and to monitor performance trends,conducting regular industry roadway development operatorsÆ workshops to facilitate the transfer of successful roadway development improvement initiatives throughout the industry and facilitate networking between development practitioners,development of alternative skin reinforcement and containment measures that would eliminate the use of steel mesh and enable face support systems to be fully automated,development of automated bolting and mesh handling systems that would enable operators to be removed from the immediate face area,development of a body of knowledge of industry roadway development practice,development of a web-based information management system to capture and transfer emerging developments in roadway development practice and technology,reviewing the Australian civil tunnelling and underground metalliferous mining sectors to identify practices and technologies that could potentially be utilised to improve roadway development performance, anddeveloping a new generation high-capacity mining system capable of +10 metres per operating hour for 20 or more hours per day (CM2010). The paper reports on the progress of the above initiatives and outlines strategies to continue the pursuit for improved roadway development performance.

Jan 1, 2008

By William A. Vogely, DeVerle P. Harris

INTRODUCTION Perspective The phrase "minerala resource appraisal" is widely and loosely used to refer to any quantitative description of a naturally occurring source of fuels, metals, or nonmetals. This leads to confusion when mineral resources are so conceived, for the term refers generically to information on stocks-mineral endowment, resources, reserves, and potential supply-that differ in ways that are important in economic analysis. Mineral resource and other stock measures- these are not flows, e.g., the supply of minerals-have precise technical meanings, which are presented in this paper. Quotation marks are used to separate the nontechnical use of mineral resource from the technical. The term appraisal also leads to some con- fusion because it too is loosely used. When an appraisal employs probability and statistical methods, the appropriate term is estimationb, not appraisal or assessment. This paper presents a conceptual framework or mineral resource information which renders technical, or well defined, relationships of mineral endowment to physical attributes of the earth's crust and earth processes, as distinct from economic values, and identifies estimation approaches that lead to different economic measures of stocks and flows. An important result of this approach is the distinction between the relevance of mineral resource information to economic and policy issues about potential sup- ply (stocks) and dynamic supply (flows across time). With regard to policy analysis, this paper recognizes that mineral resource information has a cost as well as an imputed value. Such a treatment implies that there is an optimum state of resource ignorance, or enlightenment, for a given policy issue and that the relevant economic issue is the selection of that information strategy and appraisal methodology that is indicated by the optimum state. Until the initiation of the OPEC oil embargo, the demand for information on mineral re- sources and potential supply was limited to occasional studies commissioned by Congress or the President of the United States. In these, mineral and energy resources remained loosely de- scribed. When quantitative estimates were supplied, they were not rigorously made, and the estimates and the methodology accordingly escaped close scrutiny. Usually, neither the geo- logical nor economic bases for estimation were carefully described or critically examined. The imposition by OPEC nations of the embargo on oil caused a sudden change in the public and scientific demands for specific 'resource" appraisals, especially of oil and of uranium. These

Jan 1, 1985

By Robert A. Cummings

A field inventory was made of the mineral, geologic, geothermal, and groundwater resources of three geologically recent lava fields in the desert of Oregon. The term "resource" was applied with care: a "resource" must have particular value or worth, although it need not be economically viable. The spectacular volcanic features of the area have particular scientific and general interest and thus constitute geologic resources. The mineral endowment, mostly occurrences of low unit value such as stone and cinders, in large part are not resources, due to market conditions, regulations, and other factors. These and other conclusions will be used by the Bureau of Land Management in its multiple land use planning process for the area.

Jan 1, 1980

By O. A. E. Jackson

Pebble milling has been practiced in the reduction works of South Africa gold mines for well over 50 years. Originally flint pebbles were imported from Denmark to grind stamp-mill amalgamation-process tailing, which contained a good deal of extractable gold, but local operators soon found that large pieces of ore could be used for the same purpose. The ore is a hard, tough conglomerate in which quartz pebbles are cemented together by a matrix of redeposited silica interspersed with pyrite crystals. The gold, rarely visible, occurs as fine particles mostly segregated at the interface of the pebble and matrix, although a small fraction occurs within the pyrite crystals. There is seldom any gold in the pebbles themselves. Following the usual South African practice in pebble milling, Union Corp. grinds the ore wet in two or three milling stages incorporating classification. The sized broken ore used as grinding media is separated from the main ore stream in the crushing section that prepares the ore for milling. Where the ore channel, or reef, is narrow there is a shortage of large pebbles. In this case primary grinding may be done in ball mills or, more recently, in rod mills, which cost less per ton to operate. The trend, however, is to prepare finer feed for the milling section. This makes it possible to use smaller primary pebbles and eliminates the need for steel. REDUCTION WORKS OF UNION CORP. LTD. Union Corp. Ltd. exercises financial and technical control over a group of seven gold mines in the Transvaal and Orange Free State. In the Transvaal, with one exception. the mines lie 20 to 40 miles east of Johannesburg, in flat or gently rolling countryside. Winkelhaak, the first of several new mines that will be developed by Union Corp., is located in similar terrain in an entirely new gold mining district about 80 miles east of Johannesburg. Table I gives details of milling units for six of the Union Corp. mines, together with the tonnage milled in 1957. Winkelhaak Mines Ltd. is not included, as it did not begin milling until 1958. This reduction plant has no crushing section; ore is ground directly from the mine (autogenously) in 12x16-ft mills. Because these operations are still in development, they are not described in this article. It will be noted that certain reduction works have mills of more than one size in the same milling stage. This came about when plant extensions in- corporated larger units. In the case of Geduld Propty. Mines Ltd., which began milling operations 50 years ago, the primary stage is stamp milling. The reduction works follow a uniform pattern and are usually joined to the main ore shaft. Ore from other shafts is brought by standard-gage railway and dumped into a common transfer bin. The trend is to increase surface storage capacity to enable the crushing and milling sections to operate at a steady rate, independent of fluctuating ore deliveries from mine. Milling and cyanide extraction divisions of new mines are always designed to allow for extensions as mine production increases. The conveying, washing, and screening system of the crushing section is usually laid out in final form, with additional space for more crushing equipment. The crushing sections operate on one shift during early years of mine production; a second shift is introduced when the mining rate warrants it. Ample surge capacity is provided. Crushing and milling is done only on weekdays, as the law does not allow these operations to take place on Sunday in any plants constructed since 1911. The cyanide extraction sections, however, operate continuously seven days a week, drawing on mill pulp gradually built up in the thickeners during the week. Construction and equipment of milling plants follow standard practice. Dilution water is drawn from a large, high-level tank to obtain constant pressure, but gland service water for the pulp pumps is reticulated from high-pressure, two-stage pumps. The mills are equipped with the most up-to-date machinery and are designed to save labor. They compare favorably with milling plants in countries where native labor does not exist, and automatic controls are being installed wherever feasible. Hydrocyclone classifiers have replaced mechanical classifiers in modern milling plants, chiefly because of the saving in capital outlay, maintenance, and building space. The hydroclones are fed from steady head boxes rather than directly from pumps, and dilution water is introduced into these boxes. Tests have shown that in steadiness of operation and separating efficiency cyclones are comparable to mechanical classifiers. but protective stationarv screens are needed to keep the spigots clear. Rubber-lined pumps are used for pulp of about 3 mesh or finer and metal-lined pumps for coarser material. None of the Union Corp. milling plants practices gravity concentration of coarse gold by amalgamation or the use of corduroy blankets. Studies have proved that no economic case can be made for these methods, which complicate the milling process and demand extra precautions against theft.

Jan 1, 1960

By M. A. Oskouei

Draglines are the main energy consumers in strip mines. Given the growing cost of energy and environmental concerns, it is important to properly understand dragline energy efficiency. The goal of current research at Missouri University of Science & Technology is to account for operator practice and operating conditions in modeling dragline energy efficiency. This paper presents preliminary correlation analysis and a framework for stochastic modeling of dragline energy efficiency. Thirteen operating parameters (including cycle times, payload, swing angle, and height of dump pile), operator working schedules, operating conditions, and drag, hoist, and swing energies were monitored for an 85 yd3 dragline. Operator effects were examined by two-sample t-tests. The relation between the parameters and energy consumption were assessed by correlation analysis and a stochastic modeling framework has been proposed for dragline energy efficiency. The results show that operator effects are significant (p< 0.05) and energy efficiency is correlated with operating parameters. The completed model will help the coal mines better predict energy consumption, with uncertainty, for different operating conditions.

Feb 27, 2013

By E. E. Buban

A self-contained breathing apparatus has been developed to provide complete respiratory protection for a miner in an irrespirable atmosphere. The apparatus has the desired features of comfort, reliability, maintainability, and quick-donning capability. The apparatus is packaged in a moistureproof envelope and is protected in a shock absorbing, fiberglass resin carrying case. The apparatus is a small, lightweight, one-time-use device that can be readily worn on a miner&apos;s belt, requires no maintenance and is designed to have a shelf life of five years and a carrying life of three years. It is deployed to the use position in a period of 15 to 30 seconds. Man tests conducted in-house and at the National Institute of Occupational Safety and Health (NIOSH) testing laboratories established that this unit meets all performance requirements listed in the Code of Federal Regulations, Title 30, Part 11, Subchapter B, Subpart H (CFR 30, Part 11) for respiratory protective devices. The unit, which has received joint approval (TC-13F-37) on a prototype basis from the Mining Enforcement and Safety Administration (MESA) and NIOSH has: (1) Ten-minute service life under escape conditions. (2) Thirty-minute service life when the wearer is at rest. (3) Peak-to-peak breathing resistance of less than our inches water column height. (4) Inspired gas temperature of less than 135°F. (5) Breathing gas contents greater than 19.5 volume per cent of oxygen and less than 2.5 per cent carbon dioxin. (6) A weight (complete in carrying case) of 2.75 lbs. (7) A carrying case size of 6-1/2"x 5-1/8"x 3-1/8".

Jan 1, 1974

By M. A. Trevits, I. R. Houlison, A. C. Smith, T. P. Mucho

Timely and rapid intervention to underground combustion events (fires, explosions, and spontaneous combustion) is the key to the successful control of the mine atmosphere and restoring of a coal mine to production. The focus of this paper is the utilization of a GAG 3A jet engine system to combat either large out-of-control fires or to render an entire mine inert when access to problem areas is difficult or impossible. This system is based upon a Soviet designed agricultural jet engine which consumes aviation fuel with oxygen (O2) from the intake air and exhausts combustion gases, primarily carbon dioxide (CO2) and water (H2O), along with the nitrogen (N2) from the air and small amounts of carbon monoxide (CO) and hydrogen (H2). The system is designed to approach stoichiometric combustion (ideally, pure burning that scavenges all the oxygen from the intake air). Therefore, these exhaust gases are almost entirely “inert gases”- i.e., gases which do not contribute to, and in fact, can suppress the combustion process due to the lack of oxygen. Other methods to inert mine areas have been used in the US and internationally, but these methods usually use low flow inertisation equipment or methods. Use of these low-flow inertisation equipment and methods has been successful in proactively rendering gob areas inert and has the ability to inert the entire mine workings. Due to the low flow rate, however, a substantial period of

By S. P. Marsh, M. E. Glicksman

"The effect of capillarity-driven diffusion on the recalescence of mushy zones is studied in pure materials. The solid-liquid mixture is formed by rapid partial solidification of an initially undercooled melt, and the ratio of the two phases is subsequently maintained constant by an externally imposed adiabatic constraint. A novel technique has been developed that permits tracking of the kinetics of the diffusion-controlled evolution process in situ using precision temperature measurements averaged on a length scale larger than that of the microstructure.The mean ""temperature of a mushy zone is slightly below the bulk equilibrium melting point, and is related to a characteristic length scale of the microstructure through an appropriate statistical average of the GibbsThomson equation. Theoretical considerations indicate that the diffusion controlled recalescence will progress as t- l / 3, where t is time. This behavior is experimentally verified for both succinonitrile (SCN) and ethylene carbonate (ETC), which have markedly different morphologies. The kinetic rate constant is observed to increase monotonically with increasing volume fraction of solid in the two-phase mixtures, although a firm theoretical foundation for this result has not been developed.INTRODUCTIONA dispersed multiphase system seeking equilibrium will generally contain variations in the local .free energy density. These density variations arise from such factors as variations in the bulk free energies of the phases and the distribution of interfacial energies. In this study, we examine the kinetics of diffusion-controlled recalescence in 1 solid-liquid mixture of a pure substance at its melting point. This type of two-phase system is particularly convenient to analyze because of the well-characterized physical properties of pure phases (crystals and their melts) and their interfacial energies, and the absence of any solutal effects."

Jan 1, 1986

By Albert L. Toenges

COAL mining technique progressed slowly until the advent of mechanized mining. The cutting machine was a forward step, but had only a limited effect upon improving the percentage of coal recovery. Previously, the physical fitness of the loaders and the total output of the miners fixed mine production. The miner was an independent contractor and supervision over his working place was superficial. Rising costs and the inroads of substitute fuels demanded increased output per man to lower the unit production cost. Therefore, the amount of coal loaded mechanically in underground bituminous mines has risen from 0.3 per-cent in 1923 to 7.4 in 1929, to 20.2 in 1937, and to 48.9 percent in 1943. When loading devices were introduced it became necessary to adapt them to existing systems of mining, or to alter the mining system to fit the machine. An increased amount of supervision was required as output depended upon proper operation of the machine rather than on the physical fitness of the individual.

Jan 1, 1946

IN describing the mining and treatment of ore at the Broken Hill Proprietary mine E. J. Horwood, superintendent of mines, gave the following account of the development of flotation there. It was in 1902 that the recovery of zinc from the ore by flotation was hit upon. The former general man-ager, Mr. Delprat, directed our then research officer, Mr. Carmichael, to try boiling the tailing with salt cake of which there was a considerable tonnage left over from the leaching process. The idea was the possibility of dissolving the zinc. Carmichael made the. Experi-ment, but, rather discouraged, took the glass beaker down to the general manager&apos;s office, remarking that he could not get the stuff to settle. On showing the beaker to Mr. Delprat, the latter recognized the marked distinction between the black scum on the surface and the rest of the tailings, and exclaimed: "Why, this is the very thing we are after; the zinc is floating!" Patents were applied for at once, but later on it was found that another investigator, Potter, had already hit upon the idea of flotation. His patents, however, were so involved with other operations that his process was impracticable. Litigation followed, but in the end the B. H. P. paid the Potter Company a substantial sum as settlement. In the case of Carmichael&apos;s beaker, the acid in the salt cake acted on the small amount of carbonate present in the ore, producing CO. bubbles. Owing to the aversion of sulfide crystals to being wetted, the gas as generated attached itself to the zinc in in-creasing quantities until there was sufficient to buoy the zinc particle to the surface. This action went The next problem was to apply the principle on a commercial scale, and this involved much experiment and developmental work. Various kinds of sloping copper pans with gas jets below to maintain the tem-perature were first tried, but were found too slow and too costly in operation.

Jan 6, 1928

By John H. Harden

In the valuable paper of Mr. Dunbar D. Scott and its varied discussion, on the evolution of mine-surveying instruments, the tripod-head has not received the attention it merits. During the last 50 years this very necessary adjunct to the surveyor&apos;s instrument has been much improved. The legs are of better construction; and the devices for laterally moving the instrument over the station-point and for quick leveling, without the use of the screws, have given to the instrument fitted with the modern tripod-head the same facilities possessed by the oldfashioned ball-and-socket, with more perfect accuracy, not attainable in the latter, while saving from 30 to 50 per cent. of the time required for setting the instrument over a station. For the purpose of extending the discussion to this import-

Jan 1, 1902

A process was developed, on a laboratory scale, for the removal of iron oxides from Weipa pisolitic bauxite. The technique involves the chemical reduction ofthe iron oxides by carbon, followed by selective removal of the iron species by acid leaching or chlorination.To remove more than 90 per cent of the iron it is necessary to reduce the iron oxides substantially to iron metal by heating the bauxite, pre-calcined at 650-800&#176;C, with reactive carbon at 1040-1100&#176;C. Reduction proceeds via the intermediate formation of hercynite (FeO.Al2O3) and difficulties have been encountered in reducing hercynite formed under less favourable reduction conditions.Following reduction, efficient selective removal of iron species is readily effected by acid leaching using dilute hydrochloric acid at 100&#176;C, or chlorination at 500-750&#176;C using Cl2, Cl2/N2, or Cl2/N2/CO mixtures.After removal of unreacted carbon, the final products contain 0&#183;5-1.0 per cent Fe203 and 87-92 per cent Al203.

Jan 1, 1971

By James R. Coldwell

Mining and processing cost analyses were conducted by the U.S. Bureau of Mines on massive sulfide copper-zinc and low sulfide vein gold deposit types that may be found in the Ketchikan Mining District. Reserves and recoverable metal values (RMV) needed to make these deposits economically viable were modeled. Methods for estimating ore grades and required RMV are presented. Economic modeling for massive sulfide deposits indicated the RMV necessary for a 15% Discounted Cash-Flow Rate-Of-Return (DCFROR) for an underground cut-and-fill mine ranged from $137/mt for a 6,100 mtpd on-site milling operation to $526/mt for a 450 mtpd off-site milling operation. On-site milling was always less costly than off-site milling. Economic modeling for low sulfide vein gold deposits indicated the RMV necessary for a 15% DCFROR for an open-pit mine, off-site mining operation ranged from $S4/mt at 2,900 mtpd to $71/mt at 360 mtpd, and from $49/mt at 2,900 mtpd to $100/mt at 360 mtpd for an on-site milling operation. Off-site milling was less costly than on-site milling until production exceeded approximately 1,700 mtpd. Then, economies of scale reduced operating costs enough to offset the higher capital costs required for on-site milling.

Jan 1, 1995

By W. A. Dixon Edwards

Industrial mineral production in Alberta, worth $468 million in 1997, comes from a dozen types of industrial minerals, mined by about 400 producers. Cement and lime from Paleozoic limestone formations exposed along the Rocky Mountains account for the greatest production value. Sand andgravel is the primary source ofmineral aggregate. Almost two-thirds of this aggregate is consumed in the Edmonton and Calgary regions. Sulphur produced at 48 sour gas processing plants and two oil sands plants was valued at $84.8 million in 1997 and accounted for 80% ofCanadian sulphur production. Four companies solution mine the Elk Point salt beds to produce chlor-alkali chemicals, industrial salt and sodium chlorate. Natural brine is also produced as a dust control product. Al $22 million, peat moss is a major industrial mineral product in Alberta. Other minerals with noteworthy production include shale, stone, silica and ammolite. The commodities with the greatest development potential are diamond, silica and oil sands tailings by-product minerals.

Jan 1, 2001

By Oscar Harder

IT is now just a quarter of a century since Fred W. Taylor§(23) pub-lished his classical paper On the Art of Cutting Metals, describing -his researches in which he, in cooperation with Maunsel White, had developed what is essentially the modern method of heat-treating high-speed steels. Regarding this research, Dr. Sauveur, (22) in his address on Steel Wizards, Past and Present, at the annual banquet of the American Society for Steel Treating in Philadelphia in 1920 said, "The discovery of high-speed steel, or if you prefer, of the treatment imparting high-speed properties to certain steels by Taylor and Maunsel White I am inclined to consider as our one epoch-making contribution to the metallurgy of steel." It was at about that same time (1900) that Taylor exhibited high-speed steels, heat-treated by the improved process, at the World&apos;s Exposition in Paris and attracted much attention by showing that the steels would operate at such feeds and speeds that the tips of the tools were visibly red hot. This observation must have started metallurgists to wondering regarding the relative hardness of the various steels at red-heat temperatures. Considerable work has indeed been done in an effort to measure the hardness of high-speed steels and. related materials in the red-heat range, using various methods. . The results, however, have been only partly satisfactory, owing to experimental difficulties. The present investigation had as its immediate inception an address by J. V. Emmons, of the Cleveland Twist Drill Co., to the Columbus Chapter of the American Society for Steel Treating in 1931, in which he deplored the fact that comparatively little was known with regard to the hardness of high-speed steels at elevated temperatures, in spite

Jan 1, 1933

By R. D. Irwin, W. M. Mullins, E. A. Medina

"Various stability criteria are introduced and thermo-kinetic models for metallurgical processes are used as concrete examples for evaluation. Kinetic criteria for the process of dynamic recrystallization are proposed. These criteria are compared to the non-equilibrium thermodynamic approaches discussed in the literature. The application of macroscopic stability criteria to materials processing is then discussed.IntroductionThe mechanical behavior of metals at elevated temperature is very well predicted by any of several empirical constitutive relations. Typical is the power-law (or Swift's) form,Equationwhere r-is the stress, y is the strain and m, n , t0, y0 and Q are material constants. This form has been used with some success in the metals processing area [1]. In general, though, all of the empirical constitutive equations are static, failing to account for any dynamical properties of the system they seek to describe.The physics of warm deformation is qualitatively well understood. An example is power-law creep, where the dominant mechanism is assumed to be lattice diffusion limited climb of dislocations, which allows the strain-rate to be determined by the applied stress through"

Jan 1, 1997

By D McB Martin, A Piechocka, M Jessell, M Lindsay, E Ramanaidou

The Hamersley Basin of Western Australia, approximately 500 km long by 200 km wide, is recognised globally for its rich endowment of iron ore resources. Two types of bedded iron ore mineralisation are recognised: the Proterozoic hypogene martite-microplaty hematite ores; and the more recent Cenozoic supergene martite-goethite ores. Exploration strategies depend on the style of mineralisation being targeted; however, stratigraphy and structure are fundamental controls on both ore types. Therefore, the ability to visualise the 3D geology of the entire basin is critical for the understanding of iron ore occurrences and their relationship to ore genesis of bedded iron ore mineralisation. However, due to the large size of the basin, generating a 3D geological model of the regional stratigraphy and structure has not been possible, or prioritised, primarily due to software limitations. Recent advances in implicit automated geological modelling presents an ideal opportunity to develop a 3D model of the entire Hamersley Basin. The innovative Loop software was used to model open source geological data (ie geological mapping, outcrop orientation data, and fault data) sourced from the Geological Survey of Western Australia. In addition to generating a 3D geological model, information such as stratigraphic thickness and fault offset information was extracted using the map2loop module and demonstrated its application to exploration targeting. This study demonstrates how a basin-wide 3D geological model was used to conduct a regional structural analysis of the Hamersley Basin. The results of this study provide opportunities for other prospective regions to be rapidly modelled in order to enhance the understanding of the geology and improve exploration targeting.

Nov 8, 2021

By Sean Gallagher

The human body is remarkably adaptable and capable of performance in a wide variety of environments and circumstances. It cannot be said, however, that the body is capable of performing equally well under all conditions. In fact, when faced with certain types of tasks or environmental demands, the body may have to adapt using methods that result in substantial performance limitations. Such a phenomenon is evident when workers must adopt unusual or restricted postures during performance of physically demanding work tasks. For the purposes of this discussion, the term "unusual posture" will be considered as any working posture other than typical standing or sitting positions. The term "restricted posture" designates postures that are forced upon workers due to restrictions in workspace. The vast majority of ergonomics research has focused on establishing design criteria for work involving standing (e.g., Snook and Ciriello, 1991; Waters et al., 1993) or seated postures (e.g., Grandjean, 1988), and understandably so. However, it must be recognized that there are numerous jobs (e.g., underground miners, aircraft baggage handlers, plumbers, agricultural workers, mechanics, etc.) where workers must perform in less desirable postures such as kneeling, stooping, squatting, and lying down (Haselgrave et al., 1997). Unfortunately, experience has shown that many ergonomics techniques used to analyze or design standing or sitting workstations often do not adapt well to situations where a restricted