Search Documents

By F. D. Agrensa, J. Hadjigeorgiou, E. Storimans, S. J. Thorpe

Reinforcement and surface support are part of an integrated system that transfers and shares loaduntil the excavation surface is stabilized or until the ground support system fails. Steel mesh is the most popular primary surface support element in underground hard rock mines in Canada. Mesh straps are a secondary surface support that provide additional containment as they distribute the load between and across the reinforcement elements. This investigation addresses the role of steel properties, and in particular steel chemistry, in the long-term performance of mesh and mesh straps when exposed to an aggressive corrosive environment. It reports on comparative accelerated corrosion studies to compare the resistance to corrosion of different surface support elements. This has significant implications on the choice of surface support and the anticipated rehabilitation requirements.

Oct 9, 2024

By Thomas Barczak

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear ?abutment? moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

Jan 1, 2007

By T. D. Traubert, J. T. Dietz, D. Catena

"Canadian process industry experts have often observed the strong trend for U.S. industrial safety and environmental laws to creep across the border. These experts will be interested in new United States (OSHA) regulations (29 CFR 1910.119), and anticipated new U.S. Environmental Protection Agency (EPA) regulations that will require over 28 000 U.S. refineries and chemical plants employing more than three million workers, to begin a comprehensive Process Hazard Analysis (PHA) of these complex plants immediately. Impending EPA regulations are expected to expand these efforts and add process Hazard Frequency and process Hazard Consequence reviews for many additional industrial locations.These regulations were created to reduce catastrophic industrial accidents, and emergency releases of hazardous chemicals which endanger employees, the public, and the environment.Accurate, and field verified Piping and Instrument Diagrams (P&IDs) are essential to permit a meaningful Process Hazard Analysis or emission release to be done. Today accurate P&IDs often do not exist. Many companies that have started to update their old P&IDs have found the process to be far more difficult, time-consuming,and expensive than they ever thought.This paper describes a new technique of computer drawn ""Intelligent"" P&IDs that can make a Process Hazard Analysis less expensive, more accurate, easier to perform, and provides lasting benefits to the plant owner long after the PHA has been completed."

Jan 1, 1993

By Barbara Rutter, Phillip Mulligan

This research investigates how changes in shock tunnel geometry affect the pressure versus time waveform. The Large Arena Test Simulator (LATS), which is composed of four different rectangular sections connected by three expansion sections, was used to determine how the changes in geometry affect the shock wave profile.

Feb 1, 2020

By J. L. Carr

On average, one to two fatalities occur every year when a miner is struck or pinned by a continuous mining machine (CMM). Proximity detection systems offer an effective means to prevent these types of injuries and fatalities by sensing the presence of a miner and automatically disabling machine motion. The Mine Safety and Health Administration (MSHA) is expected to finalize a regulation that would require the use of proximity detection systems on all CMMs. Approximately one-fourth of all CMMs in use in the United States are already equipped with such a system. The use of these systems will save lives, not only by automatically preventing accidents but also by acting as a tool for educating miners and reinforcing safe work practices. Researchers at the Office of Mine Safety and Health Research (OMSHR) have conducted a series of field evaluations to quantify the performance of these systems in an underground coal environment. These field evaluations measured the distance at which the warning and stop zones were activated. The technology provided consistent activation of the warning and stop zones under many of the conditions tested. However, some performance inconsistencies were observed which present opportunities to improve the reliability of proximity detection system technology. Some of the notable variables that caused significant changes in performance and should be considered in the design, implementation, and use of proximity detection systems include interaction with the trailing cable, performance changes during tramming, and orientation of the miner-worn component.

Feb 23, 2014

By S. J. Schatzel, W. P. Diamond

High methane emissions originating from the active face areas and from the fractured formations overlying and underlying the mined coalbed can adversely affect both safety and productivity in underground coal mines. Since ventilation alone may not be sufficient to control the methane levels in the longwall mining environment, gob gas ventholes have become a standard supplementary methane control option in many mines. As mines progress into deeper and gassier coalbeds, or as longwall panel size increases, ventilation and gob gas ventholes together may not be sufficient to maintain methane levels within statutory limits. To decrease the risk associated with methane emissions under these circumstances, in-seam horizontal methane drainage is often used to reduce the gas content of the coalbed prior to mining. Horizontal methane drainage borehole completion designs, drilling strategies, and degasification lead times may need to be adjusted for site-specific conditions due to mine design, geology, and the gas content of the coalbed. This study investigates different horizontal methane drainage borehole patterns, borehole lengths, and degasification times prior to and during panel extraction to evaluate their effectiveness in reducing methane emissions using a "dynamic" 3D reservoir modeling of a 38 1-m wide longwall panel operating in the Pittsburgh coalbed. Results of this study showed that dual and tri-lateral boreholes are more effective in decreasing emissions and in shielding the entries compared to fewer shorter, cross-panel, horizontal boreholes parallel to the longwall face. Modeling results showed that after 12 months of pre-mining methane drainage, the average longwall face emission rates can be reduced by as much as 10.3 m3/min and 6.8 m3/min using tri- and dual-lateral boreholes, respectively. It was also shown that if pre-mining methane drainage time is short, it is important to continue methane drainage during the panel extraction to maximize reductions in longwall face emissions since additional face emission reductions achieved during this period can be comparable to pre-mining degasification.

By Carlos España Ch

El presente texto plantea la mecanización en la mediana minería como método de trabajo para el tratamiento de minerales y trabajos auxiliares. La ejecución de esta mecanización es de acuerdo al tipo de yacimientos de cada caso particular. En este sentido, la compañía minera Alianza S.A. es un ejemplo de este enfoque empresarial, así como las minas Hércules y Coturcán, las cuales implementaron la minería sin rieles, donde el desarrollo y preparación de las vetas se realiza por medio de rampas que puedan tener pilares de 200 mt.s de largo, posibilitando el uso del método de explotación mecanizado-fronton pilar e incrementando la productividad en comparación con las etapas de mecanización incipiente.

Oct 14, 1980

At Namdeb, submerged beaches are earmarked for sampling and future mining and various sampling configurations are tested for optimality through the use of spatial simulations. For the creation of these virtual orebodies, basic statistics and variograms are needed, but in this specific instance no data exists from which the necessary parameters can be determined. The best that can be done is to use proxy data from onshore beaches, with adaptations where needed. The reworking of raised beaches during periods of rising and falling sea levels in some cases destroyed the internal beach structures, and it is very difficult to determine the variograms. A method is proposed whereby simulated annealing is used to adjust the sample locations to align the data pertaining to beach crests or cliff lines, thus improving the variogram structure along the shoreline in the direction of the highest geological continuity.

Jan 1, 2014

By Linneas W. Laage

The purpose of this report is to document the fire experiments conducted at the Waldo Mine, NM during March 1990. The U.S. Bureau of Mines is concerned with improving and validating the predictive capability of the mine ventilation and fire simulator, MFJRE. To accomplish this, fire experiments were conducted at the Waldo Mine and temperature profiles were developed as functions of time and distance from the fire. These tests then provided data for verifying the heat transfer model in the MFIRE mine ventilation and fire simulator. An initial analysis of this data indicates that it will serve this purpose well. This report summarizes the data obtained during six fire tests at the Waldo Mine.

Jan 1, 1994

By Bevan Presley

THERE has been developed at Latouche a rather unusual system of mining which, for want of a better name, has been called the "Latouche system of mining." It is a modified form of shrinkage stoping applicable to orebodies of large or fairly large size where the ground is such that timbering would not be required in stoping. Mention has been made of this method of mining by Birch,1 who gave no details as it had been in use only a short time and the final outcome undetermined. The system, however, has proved to be entirely successful and it is thought that a paper covering it might be of general interest. Before proceeding with a detailed description of the "Latouche system" a brief description of the property and the various mining methods previously used will be given. LOCATION The Beatson mine of the Kennecott Copper Corp. is situated on the west coast of Latouche Island-, in Prince William Sound, Southwestern Alaska, 45 miles east of Seward, the coast terminus of the U. S. Government Railroad. It is a regular port of call for ships on the Southwestern Alaska run. The island is about 12 miles long and 3 miles wide. A ridge of mountains runs the entire length with a maximum elevation of 2500 feet. CLIMATE Latouche has to contend with possibly the greatest amount of precipitation on the North American continent. The annual average precipitation for the past 4 years has been 188 in., with 248 in. for the year 1926. A rainfall of 4 in. per day is not uncommon. In the winter the thermometer rarely falls below +20° F. and the snowfall is usually heavy during the months of March and April.

Jan 1, 1927

By Kim M. Cornelius

Musculoskeletal injury is a term used to describe a wide range of soft tissue disorders which affect the nerves, tendons, and muscles. Common examples include lower back pain, tendonitis, and carpal tunnel syndrome. The majority of these injuries are not the result of sudden mishaps, but usually develop gradually from repeated wear and tear. Symptoms may first appear after weeks, months, or even years. Symptoms may result from many types of activities, performed at work or at home, and it is often difficult to attribute a single event. In fact, it is more common to identify the factors which may have contributed to the development of the condition. The terms repetitive strain injuries or cumulative trauma disorders (CTDs) have been commonly used to refer to disorders that have occurred due to work related activities (Putz-Anderson, 1988; Fraser, 1989). Three main risk factors contribute to CTDs: force, repetition, and awkward postures. Any one or combination of these may contribute to the development of CTDs. Therefore, the design of equipment in conjunction with the required tasks should attempt to reduce these risk factors. Examining the layout of the work area to help identify tasks which may contribute to cumulative trauma is necessary. The following list(Putz-Anderson, 1988), describes ergonomic concerns that, overall, should be minimized at the work area:

Jan 1, 1997

By J. A. McCamley

Gypsum scrap generated from wallboard manufacturing, construction and deconstruction activities in North America, Europe and Japan is a recognized environmental problem. Landfill disposal of this gypsum scrap is problematic, with deposits often creating hydrogen sulphide emissions and metallic sulphide groundwater leachates. Of these regions, Europe is the most advanced in dealing with the issue having enacted legislation, which will come into effect in July 2005 that will strongly encourage gypsum recycling throughout the EU. An estimated 10% to 17% of all gypsum used in the wallboard industry becomes recyclable scrap, which represents approximately 1% of the total waste stream in North America. In the United States, 2.5 to 4.5 Mt of gypsum scrap is generated each year; the volume is similar in Europe (the percentage of total tonnage is less because of the higher use of brick and concrete). The Greater Vancouver region of British Columbia has banned gypsum from its landfills, and as a result, all gypsum scrap is now recycled. New West Gypsum Recycling, a Canadian firm, uses its proprietary technology to process large quantities of gypsum scrap that is reincorporated into new wallboard, at percentages ranging up to 25%. The operation of New West Gypsum Recycling Inc. of Langley, Vancouver is examined as a case study and recommendations are provided as to how other urban regions can implement similar gypsum scrap recycling programs.

Jan 1, 2004

By Otto Wartenweiler

AFTER the phenomenal development of the new mine, the United Eastern Mining Co., with Mr. Frank A. Keith as President, decided to install a reduction plant. The character of the ore, closely resembling the product of other mines in the district, did not offer any particular metallurgical problems, since these neighboring mines had been operating milling plants very successfully for several years. Thus, with the general metallurgical treatment fairly well-defined, the matter of next importance was to design and construct a plant as economically as possible, that would give the best results obtainable. The ore consists of a mixture of calcite and quartz in about equal quantities with some decomposed andesite, while the average value of mill heads were calculated to be $20 plus in gold, no silver being present. The tonnage to be treated at ,the start was fixed at 200 tons, but, in view of the favorable condition of the mine, it was considered advisable to arrange facilities, for increasing the capacity to 400 tons. . While it is best in some cases to adopt a distinct independent unit system where future enlargement is contemplated, in this instance the plans worked out differently. Summarized, the treatment adopted consists of coarse crushing, coarse grinding, fine grinding and cyanidation. For coarse crushing the selection of the No. 6 size gyratory crusher was governed not so much by its capacity as by the size of the feed openings to properly receive the run-of-mine material, which was too coarse for a No. 5 crusher. To accomplish the coarse grinding to. best advantage, a careful comparison was made between the modern steel ball mill-the last word in crushing and grinding-and one of its older, and, at that time better-established, competitors, the rolls.' The following conclusion was reached: While it is possible that for the sized plant under consideration the cost of operating rolls might be a little cheaper, it is preferable to use ball mills because a simpler arrangement is possible, and1 because. the handling of, ball mills is preferred by the operator.

Jan 11, 1917

By S. C. Suboleski

Forecasts indicate that the acid rain bill currently before Congress is likely to cause an increase in demand of 30 to 40 million tons per year of compliance quality coal from Central Appalachia. This represents a doubling of this segment of the coal business. This paper will examine how this doubling can be met, what the likely implications for pricing are, the major uncertainties associated with these predictions, and the likely outcomes of the growth in compliance coal. Finally, some implications for fuel planners will be discussed.

Jan 1, 1993

By A Campbell

Open pit blasting at Ernest Henry Mining has the potential to cause damage to nearby underground workings. This paper is a case study of the blast vibration management project that was conducted to ensure open pit blasting did not adversely affect the stability of upper production levels or cause damage to the underground primary fan units. The two upper levels of the underground mine surround the lower portion of the open pit mine. The remaining underground mine workings are directly below the open pit mine. This paper details the process developed to prevent open pit blasting causing excess vibration in the underground mine. Measurement of test blasts combined with historic blast monitoring data was used to determine site specific blast vibration parameters. Threshold vibration levels for blast-induced damage to underground drives and the fan chambers were developed from benchmarking and non-linear numerical modelling. A Monte Carlo simulation model was used to predict vibration levels in critical underground areas. Blasts predicted to exceed maximum vibration levels could then be redesigned to avoid damage.A scale distance law for determining peak particle velocity (PPV) from the distance and charge weight of blasts was developed. Underground observations were used to develop a site-specific relationship between PPV and ground support/rock mass damage. A Monte Carlo superposition prediction model was developed and compared to measured data to refine input parameters. Standards for redesigning open pit blasts in order to reduce blast vibrations whilst minimising impacts on productivity are described. Non-linear numerical modelling was used to establish the dynamic capacity of the fan chambers, and set a PPV of 250 mm/s as a threshold for damage. The numerical model captured the full dynamic behaviour of the fan chambers and installed support, including transient stresses, strains and induced damage, when subjected to a simulated open pit blast.This case study also outlines a procedure for monitoring and predicting blast vibrations at other mine sites where open pit blasting has the potential to impact on a nearby underground mine.

Nov 8, 2011

By Richard G. Warren, Michael M. Minor, Gayle J. Thomas

INTRODUCTION Los Alamos Scientific Laboratory (LASL) initiated its effort in the Hydrogeochemical and Stream Sediment Reconnaissance (HSSR), a part of the Department of Energy (DOE) National Uranium Resource Evaluation (NURE) program, in late 1975. Since that time, LASL has completed sampling of the Rocky Mountain states of New Mexico, Colorado, Wyoming, and Montana at a density of about one water or waterborne sediment sample per 10 km2 and has sampled about 85% of Alaska at a density of at least one per 25 km2. Analytical results for these samples are reported by National Topographic Map Series (NTMS) quadrangle. All collection and analytical procedures have been standardized from the outset (Sharp, 1977; Sharp and Aamodt, 1978). Until early 1979, only uranium results were reported for these samples; thereafter, results include analyses for at least 42 additional elements in the sediment samples. Each LASL HSSR report also includes a discussion of the relationship of these analytical data to known or possible uranium resources; more recently, these data have been re- examined for their relationship to resources for other metals (Beyth et al., 1980; 1980a). Analytical results for LASL HSSR sediment samples are both comprehensive, including 43 elements, and precise, allowing close inter-comparison of data between quadrangles. A recent HSSR study shows that elemental concentrations in sediment samples from the Dixon Entrance quadrangle in Alaska are insensitive to the choice of sieve size fraction and do not vary significantly between stream locations a few meters apart, except for extremely high elemental concentrations (Warren, et al., 1980). Elements that are particularly reproducible include thorium, hafnium, and the .ram earth elements. Fortunately, sensitivities for these elements, which are often associated with uranium, are excellent by the nondestructive analytical technique of neutron activation analysis that LASL employs. Wet chemical techniques may not always give reliable results for these elements in sediment samples due to the difficulty of dissolving the resistate mineral phases that normally contain these elements. LASL has recently open-filed results for a large number of NTK3 quadrangles; to date analyses have been reported for about 605 of the quadrangles within the states of the Rocky Mountain region. As a result, uranium analyses am now complete for all sediment samples collected from the state of Wyoming. We have chosen to sumnarize the analytical results for Wyoming and portions of adjoining states hereafter termed "the ~ Wyoming regionn (Fig. 1 ) ; nearly 24 000 uranium analyses and nearly 17 000 analyses for 42 additional elements are available for sediment samples collected from this area. The DOE open-file report numbers are shown in Fig. 1 for reports open filed before September 1, 1980. The Wyoming region provides an ideal area for an examination of regional geochemical patterns ex- hibited by sediment samples. It is endowed with a variety of exposed geologic units and with widely distributed uranium districts associated with host units of several ages. However, discussion will focus on rock units of Eocene and Precambrian ages because they are widely exposed and host the majority of the uranium resources within the region (Fig. 2). Miocene units are also widespread and host mineralization in the Brown's Park Formation (Fig. 2). Epigenetic uranium mineralization occurs in sand- stones of lower Eocene age such as the Wasatch, Battle Springs, and Wind River Formations whereas vein type mineralization occurs in Precambrian crystalline rocks. Precambrian rocks within the region consist of a variety of granitic and meta- morphic rocks with l .4-2.8 billion year ages, except within the Uinta Arch, where they consist of a sequence of very low grade metamorphosed or unmetamorphosed 1.0 billion year old sedimentary rocks. Precambrian rocks have served as sources for much of the clastic material comprising the lower Eocene units, and may also have provided the source for the uranium in mineralized Eocene or Miocene sandstones (Stuckless, 1979). The remainder of this paper describes the relationship of elemental concentrations in HSSR sediment samples to exposures of Eocene and Precambrian rocks. The results are used primarily to determine where these Precambrian rocks might provide the most suitable uranium source areas and to infer the direction of transport toward adjacent depositional basins during the Eocene.

Jan 1, 1980

By H. Conrad, V. V. Damiano, G. J. London

The slip mode activated during the c axis compression of single crystals of commercial-purity ingot SR beryllium, high-purity (twelve-zone-pass) beryllium, and Be-4.4 wt pct Cu and Be-5.2 wt pct Ni alloys in the temperature range of 25° to 364°C was determined using two-surface slip trace analysis, slip-step height analysis, and electron transmission microscopy. All three techniques indicated the occurrence of copious pyramidal {1 122) (1123) slip in the alloys over the entire temperature range, the amount increasing with temperature. Pyramidal slip was also indicated in the high-purity beryllium by slip trace analysis and electron transmission microscopy, but the amount was somewhat less than in the alloys. For the commercial-purity ingot crystals, only a very small number of pyramidal slip lines were observed, and these were in the immediate vicinity of the fracture surface. No pyramidal dislocations could be detected by electron transmission microscopy in this material. Dislocatransmissiontions with Burgers vectors [0001] and +(ll20) were identified by electron transmission microscopy inthe (1122) slip bands, as well as those with the j (1123) vector. This was interpreted to indicate that the edge components of the 3(1123) vector dislocations activated during c axis compression dissociate upon unloading according to the reaction i (1123) — [0001] + 3(1120) THE microstrain c axis compression of single crystals of commercial-purity ingot SR beryllium (99.6 pct), high-purity twelve-zone-pass beryllium (99.98 pct), Be-5.24 pct Ni and Be-4.37 pct Cu alloys was described in a previous paper.1 This paper covers in detail the analysis of slip traces observed on two mutually perpendicular lateral surfaces of these specimens, and a detailed description of transmission electron microscopy studies performed on foils cut from the bulk crystals after they had been deformed to fracture in the c axis compression. Observation of slip traces on single surfaces of deformed single crystals are generally insufficient to positively identify slip or twinning modes. The use of two carefully cut and oriented perpendicular surfaces can greatly aid in the positive identification and index- ing of slip traces, although even this technique may be quite inadequate if more than one type of slip system operates and if an insufficient number of traces are observed on the surfaces. The problem is greatly simplified for symmetric cases like that for c axis compression of an hep crystal such as beryllium, in which the operating slip systems are all equally inclined to the direction of the applied stress, and each slip system of a given slip mode has an equal chance of operating. For such cases, the traces of any given slip mode observed on the surfaces cut parallel to the c axis are symmetrically tilted about the c axis. It is therefore possible to quickly determine whether one or more slip modes are operating. Confirmatory evidence in support of the observations made on the external surfaces can be obtained from foils cut from the deformed crystals and examined by transmission electron microscopy. This latter technique serves to identify not only the operating slip plane but also the Burgers vector of the dislocations which participate in the slip. For this purpose, a simplified technique based upon a double tetrahedron notation is used in the present paper. The planes and directions in the hep lattice are all designated by letters rather than indices and extinction conditions are easily determined if the Burgers vector lies in the plane contributing to the diffraction. RESULTS 1) Slip Trace Analysis. The standard (0001) stereo-graphic projection of beryllium is shown in Fig. 1. The two mutually perpendicular, lateral surfaces of the compression specimen are represented by the diametrical planes AA' and BB', also referred to as surface A and surface B. For the specific case represented (a Be-5.24 pct Ni specimen deformed by c axis compression at room temperature), the A surface is tilted 5 deg to the (10i0') plane and the B surface is tilted 5 deg to the (1120) plane. Two surface trace analyses may be facilitated by examining in turn the intersection of various great circle traces of specific pyramidal planes with two surfaces and comparing the angles made with the (0001) plane with those actually observed on the two surfaces. One then identifies the slip traces by trial and error on a best-fit basis. The (1122) type planes (it was found that slip occurred on these planes) are shown plotted on the stereographic projection in Fig. 1. One obtains directly the angles between the (0001) plane and the {1122) traces by measuring the angle from the periphery to the point of intersection along the lines

Jan 1, 1969

By Marco Fellin, Van E. Komurka

Significant cost and construction benefits were obtained from performing a bi-directional static load test prior to construction on the Russell Street Bridge Replacement project in Missoula, Montana. The project utilized 24 drilled shafts to support two three-span bridges across the Clark Fork River. A bi-directional static load test (“BDSLT”) was performed on a large-diameter production shaft to demonstrate construction methods and confirm design assumptions. Subsurface conditions consisted of gravel with sand to a depth of 20 feet (6.1 m), underlain by gravel with sand, silt, cobbles, and occasional boulders. The test shaft had a nominal diameter of 5.9 feet (1.8 m), and an embedded length of 75.5 feet (23.0 m). The geotechnical engineer of record and the BDSLT test engineer collaborated to optimize the BDSLT jack assembly location within the test shaft, determine appropriate instrumentation locations, and plan the test protocol. The maximum applied test load was 10,707 kips (47.6 kN). Significant benefits were obtained from performing the BDSLT test, including 1) reducing each production shaft’s length by using a higher LRFD resistance factor allowed by having performed the testing, 2) using test-determined unit shaft resistances to evaluate and accept two production shafts that may have otherwise required remediation, and 3) providing the Montana Department of Transportation (and other designers) with increased presumptive unit resistance values in the gravel/cobble/boulder deposits. PROJECT DESCRIPTION The project was constructed in Missoula, Montana for the Montana Department of Transportation (“MDT”). The original bridge was approximately 60 years old, and consisted of a two-lane, 420-foot-long (128-m), four-span, riveted steel plate girder design spanning the Clark Fork River. The bridge was due for replacement owing to its deteriorated state, and the need for increased traffic volume capability afforded by a four-lane structure. HDR was the structural engineer. The preferred bridge alternate was a 459-foot- long (140-m), three-span, welded steel plate girder design. The new bridge was designed to meet current standards in accordance with MDT bridge design and AASHTO LRFD criteria. The new bridge was constructed in phases to keep traffic open during construction.

Jan 1, 2019

By Alexandre de Freitas Gomes de Mendonça

São crescentes as exigências por confiabilidade nos processos siderúrgicos. Nesse contexto, a Usiminas tem direcionado esforços em suas aciarias na busca da melhoria contínua dos processos garantindo a maior estabilidade operacional. O lingotamento contínuo é responsável pela solidificação controlada do aço líquido. A solidificação inicia-se no molde pela formação de uma pele que sustenta o núcleo líquido ao longo da máquina. O rompimento dessa pele representa um dos maiores problemas no processo de lingotamento contínuo por vazar o aço líquido no interior do veio e atingir as partes eletromecânicas da máquina. Essa ocorrência oferece risco de dano às pessoas, promove a interrupção do lingotamento no veio, sucateamento de produtos e indisponibilidade momentânea do equipamento. Visando reduzir a frequência de rompimentos, a Usiminas repotencializou o sistema de exaustão de vapor, adequou o sistema de detecção de rompimento de pele e criou uma equipe multidisciplinar para análise de cada evento. Essas ações reduziram significativamente a frequência dos rompimentos de pele na Aciaria 2 da Usina de Ipatinga, a ponto de registrar 539 dias sem esse evento.

Aug 17, 2017

By A D. Strand

The Coeur dÆAlene mining district in northern Idaho, USA is the second largest producer of silver in the world. The Proterozoic Revett Formation hosts most of the mesothermal Ag-Pb-Zn vein ore in the district; it consists of informally designated lower, middle, and upper members. All three members show up to an order of magnitude of southward thickening across the regionally significant Osburn fault. Changes in thickness of the Revett Formation across the Osburn fault reflect a major, down-to-the-south, crustal-scale fault that:was active during sedimentation, was periodically reactivated during the structural and metallogenic history of the district, and likely provided first-order control over regional fluid flow during mineralization events. Where vein structures intersect favourable strata, they produce rich ore; where vein structures cross unfavourable strata, they are poorly mineralised or barren. The most favourable host rock in the district is quartzite, which accounts for the large production from the quartzite-rich Revett Formation.The district has five main types of hydrothermal alteration:feldspar destruction, hydrothermal bleaching, carbonatisation, sulfidation, and silicification. Feldspar destruction is the most extensive and pervasive type of alteration, involving the district-wide absence of feldspar from Belt Supergroup rocks. Hydrothermal bleaching results from the destruction of hematite; it forms alteration envelopes that extend for tens to hundreds of metres into the wall rocks around many of the mineralised veins. Siderite alteration is most diagnostic of mineralisation, forming alteration envelopes that extend for tens to hundreds of metres into the wall rocks around all mineralised veins. Fine-grained arsenopyrite and/or fine-grained pyrite commonly form alteration zones adjacent to high-grade ore shoots that extend for metres to tens of metres into the wall rocks. Widespread silicification is most easily recognised by the presence of numerous quartz veins.

Jan 1, 2002