Search Documents

By H. C. Fiedler

Heats of high purity iron containing 3.1 pct Si and be -tween 0.0003 and 0.0295 pct N were prepared by vacuum melting ad then pouring while in a nitrogen atmosphere with the pressure between 0 and 90 psi. Strip from a heat with 0.0184 pct N underwent complete secondary recrystallization during the final anneal. Heats with less nitrogen had too few Si3N4 particles to restrain normal grain growth, and the heat with higher nitrogen had too many particles to allow complete secondary recrystallization. In the hot-rolled structure, Si3N4 precipitates only at the grain boundaries, with the consequence that annealing after hot-rolling diminishes the ability to subsequently undergo secondary recrystallization. In contrast to this behavior, ALNprecipitates uniformly in the hot-rolled structure. Under 1 atm of nitrogen, Si3N, in 3.1 pct Si-Fe dissociates between 900" and 950°C; the solubility of nitrogen increases from 0.0010 pct at 900" to 0.0030 pct at 1200°C. The solubility of nitrogen in Si-Fe has been the subject of many investigations. Corney and Turkdogan1 heated a 2.83 pct Si alloy in nitrogen and found the solubility, under 1 atrn of nitrogen, to be 0.0019 pct at 900°C. They claimed that Si3N4 did not form in the alloy above 705°C in 1 atrn of nitrogen. Fryxell et al.2 heated samples of 3.25 pct Si-Fe containing 0.0025 pct N over a range of temperatures and then analyzed for total nitrogen by vacuum fusion and for nitrogen in solution by a modified Kjeldahl technique. At 900°C, they reported the solubility of nitrogen in equilibrium with Si3N4 to be 0.0011 pct. pearce9 found the solubility of nitrogen at 900°C under 0.95 atrn of nitrogen to be 0.0017 pct in a 3.06 pct Si alloy. He reported that Si3N4 does not form above 770°C in 1 atrn of nitrogen. Although internal friction measurements have given somewhat higher values for the solubility,4-6 if the solubility of nitrogen is as low as has been reported by most investigators, and if Si3N4 is stable up to at least 945°C at 1 atrn pressure of nitrogen as reported by Seybolt,7 a small amount of nitrogen in properly processed Si-Fe should be effective in promoting secondary recrystallization. The requirement is that in the final heat treatment there be enough small, well-dispersed particles of Si3N4 to restrain normal grain growth. Fast8 has obtained secondary recrystallization by nitriding high-purity 3 pct Si-Fe after hot-rolling to a thickness of 0.118 in., followed by processing to 0.012 in., and annealing. A large amount of nitrogen, 0.076 pct. was introduced during the nitriding heat treatment, but he has since reported9 that "a few hundredths of a percent" is sufficient. Small amounts of aluminum10 or vanadium" nitride are capable of promoting secondary recrystallization. Heats containing as little as 0.010 pct A1 or 0.042 pct V and from 0.006 to 0.009 pct N underwent complete secondary recrystallization at final gage, whereas heats with lesser amounts of aluminum or vanadium did not.l2 To be reported is the behavior of nitrogen in high-purity 3.1 pct Si-Fe, and the relation of this behavior to the ability to undergo secondary recrystallization. PROCEDURE Ingots weighing 1 lb were made by vacuum melting high-purity electrolytic iron (A104, Glidden Co.) and high-purity silicon (Monsanto Co.). The latter was used in preference to ferrosilicon to insure a low aluminum content. The design of the melting furnace permitted pouring with the furnace atmosphere either below or above atmospheric pressure. Accordingly, at the completion of melting, nitrogen was admitted to the desired pressure and the heat then immediately poured. The ingots were sound, with no indication of porosity. In Table I are listed the heats investigated, the nitrogen pressure at pour, and the nitrogen and oxygen contents as determined by vacuum fusion with a platinum bath at 1850°C, a procedure which insures measurement of the total nitrogen.13 In addition, all heats contained 3.1 pct Si and not more than 0.002 pct C, 0.003 pct S or 0.005 pct Al. It was subsequently found that the quantity of nitrogen contained in the heats in Table I does not necessarily represent that obtained under equilibrium conditions. For example, the ingot poured immediately after 1 atrn of nitrogen was admitted to the chamber contained 0.0093 pct N, whereas an ingot poured 3 min after the nitrogen was admitted contained 0.021 pct N and another poured after a 6-min delay contained 0.029 pct N. While some bleeding of the hot top occurred in the latter instance, the ingot when examined in cross section appeared sound. The ingots were heated to 1325°C in hydrogen and rapidly rolled to 0.080 in. in 3 passes. The roll speed of the final pass was reduced so as to increase the quenching effect of the rolls. The hot-rolled pieces were processed both as-hot-rolled and after heating for 3 min at 900°C in hydrogen. After cold-rolling to 0.026 in., the strips were heated for 2 min at 900°C in hydrogen, then cold-rolled to the final gage of 0.012 in. The loss of nitrogen in going from the ingot to cold-rolled strip was no more than 10 pct. The final heat treatment, which was for the purpose of develop-

Jan 1, 1970

By Rauf Hurman Eric

In this review paper the effect of composition and temperature on electrical conductivity and viscosity of the slags encountered in electric smelting of PGM-containing sulfide concentrates is described along with their liquidus temperatures. Optimization of slag composition is attempted on the basis of opposite trends of viscosity and electrical conductivity. Metal losses to slag, matte-slag separation and matte settling are also discussed in conjunction with interfacial and surface tension concepts. The electrode immersed in the slag phase is the main factor in the design and operation of the furnace. The most important electrode parameters are the size and the positioning in the slag phase which are determined by the slag resistivity, furnace resistance, cell constant and power input. The flow of heat generated by the electrode current determines the energy distribution and furnace dimensions creating viscosity profiles within the slag phase which in turn affects the flow conditions. Thus the flow of slag is discussed together with furnace geometry, stirring action, buoyancy and electromagnetic effects and the action of the electric furnace as a settler is emphasized. A discussion on the design d production capacity of the furnace is provided which are based on considerations derived mainly from slag properties.

Jan 1, 2006

"In numerous meetings, conferences and discussions over the past year, the Conference Board of Canada has been impressed with the efforts of Canadian organizations to improve their competitive position. The attempt should be made to try to pull together and synthesize what has been heard. The topic of this paper, however, is even more daunting. The task is not only to analyze and discuss what is happening now, but also to look into the future—to the year 2000.The future seems to have an endless capacity for surprises, often unpleasant. This is one of the lessons learned in the twentieth century, particularly over the last 15 or so years.This paper covers three areas of managing in a changing com¬petitive environment: (1) the major global and domestic trends that will influence the ways in which Canadian organizations are managed (2) how Canadian companies are responding or will need to respond to these trends; and (3) the implications of the preced¬ing for human resource management and human resource professionals."

Jan 1, 1991

"The South African Mineral Resource Committee (SAMREC), a Working Group of the SAMREC/SAMVAL Committee (SSC), under the joint auspices of the Southern African Institute of Mining and Metallurgy (SAIMM) and the Geological Society of South Africa (GSSA) developed the SAMREC Code. The Code sets out minimum standards, recommendations and guidelines for public reporting of exploration results, mineral resources and mineral reserves in South Africa. It is applicable to the reporting of all styles of solid mineralization or economic deposit. However, certain commodities, namely coal and diamonds, have specific additional reporting requirements. The Code does not apply to oil, gas or water."

Jan 1, 2003

By A. S. Hall

Significant pyrite often does not dissolve in the Sobek (1978) nitric acid extraction; therefore, the standard conservative approach is to estimate pyrite using sulfur present in the sum of the nitric acid and residual sulfur fractions. Alunite, when present, appears as residual sulfur. Because alunite does not generate acidic effluents, overestimation of AGP can occur if all residual sulfur is assumed to be undigested pyrite. Evaluation of 16 samples from the Florida Canyon Mine revealed that petrographic examination coupled with a modification of the Sobek method to include a 6 hour hot (250°F) 'nitric acid extraction resulted in a more accurate estimation of AGP.

Jan 1, 1999

By H. A. Schwartz

THE spheroidal form of the temper carbon nodules in malleable cast iron and of the graphite mottles of "mottled" cast iron suggests that in both all the graphite in a given mottle or nodule grew from a single center of crystallization or nucleus. ? There is, however, a distinct metallo-graphic difference between the mottle and the nodule; the area of mother metal impoverished in combined carbon by the crystallization of graphite in a mottle is practically coextensive with the ramifications of the graphite, while the impoverished zone of metal corresponding to a given nodule is always larger, and usually much larger, than the approximately spherical mass of graphite crystals forming the nodules. Furthermore, the mottle probably is formed during freezing and the nodule almost always at a considerably lower temperature. Assuming that the nodules or mottles can be used as a measure of the existing nuclei (capable of germination) we propose to record certain observations as to the graphitizing reaction in the light of the number and habits of growth of these nuclei. The present authors, in cooperation with others1-7, have reported upon various cognate aspects of the problem. The fact that temper carbon is a mass of flakes and not a solid granule has become well recog-nized since the introduction of an improved polishing technique8,9,10 for cast iron. The problem of deriving from the circular planar intercepts

Jan 1, 1936

By X Hill

Throughout the 2016/2017 financial year, the NSW Resources Regulator conducted an assessment of each underground metalliferous operation across the state to assess how each operation managed the principal mining hazard of ground and strata control. The assessment considered all aspects of the mining process, including all aspects of managing geotechnical risk within drawpoints. This assessment is ongoing and, therefore, this paper is limited to the first six mines assessed in the program.In 2015 there were three fatalities in and around underground drawpoints in Australian metalliferous mines. Whilst many of the systems of work around underground development are consistent across the industry, there are large discrepancies around how each underground mining operation manage the risks associated with drawpoints.For drawpoints to be effectively managed, their management needs to be considered at the earliest stages of the mine planning process. By using downholes and adopting remote systems of work – systems that are continuing to improve with technology – the risks drawpoints posed can be greatly reduced.The assessment by the NSW Resources Regulator revealed a number of common failings across the state in the management of the risks that drawpoints pose. The assessment also observed a number of innovative practices that particular operations have adopted in the wake of serious incidents occurring within drawpoints at their operation; however, these practices have not been communicated to other operations.It is hoped the learnings from the assessment can be considered by industry and reduce the risks drawpoints pose in underground metalliferous mines.CITATION:Hill, X, 2017. Learnings from review of drawpoint management across New South Wales mines, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 143–150 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Joel Anderson

Allvac 718Plus is a newly developed superalloy with a good potential for use in fabricated aircraft engine structures when service temperatures exceed 650°C; the limit for standard alloy 718. Fabrication involves welding, where cracking usually is a prohibitive factor. Comparison of the solidification cracking behavior between these two alloys was made by Transvarestraint testing. It was shown that the total amount of cracking was significantly lower for 718Plus alloy, which was associated with a lower amount of ?/Laves or ?/NbC eutectic-type constituents. This in turn is believed to be due to the lower iron content of the Allvac 718Plus material. The analysis of alloying element segregation both within primary dendrite and interdendritic constituents clearly indicates that the segregation of Nb is the controlling factor in determining the final solidification microstructure in these alloys. The Nb concentrations of these constituents are significantly higher compared to the bulk alloy concentration. This was confirmed by the SEM-EDS analysis and calculations assessed with JMatPro, the latter also indicated that alloy 718 is more prone to form Laves and NbC eutectic-type constituents compared to Allvac 718Plus material.

Jan 1, 2008

By Nickolas Vlahopoulos, Nicholas Stowe

A concept has been proposed for the focusing of underwater energy. An array of spherical TNT charges is used to achieve this aim. The goal of the present research effort is to model such a system and identify optional arrangement and detonation timing schemes. A fast-running model is necessary to perform optimization analysis due to the highly iterative nature of most optimization algorithms. This requirement renders the use of sophisticated numerical solvers impractical. An analytical, physics-based model must be developed to satisfy the demands of the multiple charge optimization problem. This model must capture shock propagation speed, pressure-time histories throughout the fluid domain, and multiple charge interaction phenomena. Such a model is presented herein.

Jan 1, 2012

By V. G. Papangelakis, A. Dani

"Alkaline pressure oxidation, particularly in the presence of trona as additive, can be used to oxidize high carbonate refractory gold ores as it prevents the formation of CO2 in the autoclave. However, the presence of silica in the ore can lead to the encapsulation of pyrite due to the solubility of silica in alkaline solutions and its subsequent reprecipitation on the reacting pyrite surface, leading to the formation of a passive layer. This fundamental study investigates the chemical composition and thickness of the passive layer on a rotating pyrite disk using XPS and SEM, as a function of process conditions at 230°C, in an aqueous slurry containing silica sand, sodium carbonate and calcium carbonate under 100 psi of oxygen overpressure.INTRODUCTIONAlkaline pressure oxidation (POX) has been used successfully to treat high carbonate refractory gold ores, which contain carbonates in addition to sulphides, most notably at Mercur and Goldstrike mines operated by Barrick Gold. There are several advantages to using alkaline POX over its acid counterpart, especially due to high carbonate content. First, it eliminates the production of CO2 in the autoclave without resorting to pre-acidification, which allows for high oxygen utilization. Second, alkaline POX suppresses the formation of elemental sulphur and intermediate sulphur oxyanions (such as thiosulphates and dithionates), which reduce gold recovery. Third, the use of sodium hydroxide or salts prevents the formation of anhydrite scale by forming soluble sodium sulphate. Other advantages are the use of cheaper materials of construction and the formation of non-acidic residue that do not require further treatment prior to cyanidation (Thomas, 2005).Sodium carbonate in particular is a promising reagent for alkaline POX because it was shown to significantly accelerate the kinetics of pyrite oxidation by molecular oxygen, when compared to other reagents such as sodium hydroxide, sodium borate and calcium hydroxide. This has been attributed to the following factors: a) the faster oxidation kinetics of Fe2+-CO3 complexes compared to Fe2+ oxidation, b) the buffering effect of carbonate ions on the acidic pyrite surface, and c) the increased solubility of oxidizing Fe(III) species due to carbonate complexation (Caldeira, 2010)."

Jan 1, 2012

By R. Bainbridge

"IntroductionTHE LEAD SMELTING Department of The Consolidated Mining •and Smelting Company of Canada, Limited (Cominco), at Trail, B.C. treats materials from numerous sources for the recovery of lead, •and, of secondary importance, for the .recovery of sulphur as S02• The Department's sintering section has a .capacity of 1,500 tons daily. This section is being replaced by •a new charge-•handling and sintering plant with a daily capacity of 2,000 tons of finished sinter. Materials handled in the sintering section comprise concentrates, ores, and fluxes from Company mines and from 'custom' (independent) producers, together with intermediate products from various plants of Cominco'•s Metallurgical Division, all of which must be treated to, make up a chemically balanced charge of a predetermined lead content for the sintering plant.As received, 80 •per .cent of these materials are finer than 200 mesh, and one-quarter of the tonnage (dry basis) is a slurry .at 30 to 40 per cent moisture. This slurry, a -residue from the electrolytic zinc operation, was, for many years, partially dried before being mixed with other dry materials to make up the sinterplant charge.Some experimental work carried out in 1937 indicated that the metallurgy of the sintering operation could be improved by adopting a technique of 'wet-mixing' followed by controlled drying and nodulizing."

Jan 1, 1953

By N Yarahmadi

Characterization of pore pressure is critical for appropriate design of tailings dams. Furthermore, if seepage rates through tailing embankments increase unexpectedly or become uncontrolled, undesirable conditions may prevail to progress piping or internal erosion that could lead to the dam’s instability or ultimate failure. A three-dimensional seepage analysis was performed on a tailings dam using finite element method to find the rate of seepage and pore water conditions in the embankment and foundation. The results were then compared to a conventional two-dimensional seepage analysis carried out on the typical cross section of the embankment and the field data acquired from the instrumentation system. Considering the monitoring data, comparison of seepage analyses results for the two and threedimensional models, showed that the results of the conventional two-dimensional seepage analysis are significantly underestimating reality. Relying on two-dimensional seepage analyses might result in underestimation of seepage rates and impact the safe operation of tailings dams. Similarly, unrealistic prediction of pore water pressure conditions, based on simplified seepage analyses, can lead to overestimation of the rate of strength gain of material and consequently safe embankment raising rates.

Jul 1, 2021

By A. Atrafi, L. Barroilhet

The top size of particles in the flotation of potash ores, which can be as large as 4 mm, exceeds by far the top size in other flotation plants. It is then understandable that while long chain amines are used in the flotation of fine fractions (below 0.8 mm) of potash ores the coarse particle flotation also requires an extender oil. While new and very promising fluidized-bed flotation machines (e.g. HydroFloat) constitute a significant development in the flotation of coarse particles, in the area of extender oils, as reviewed in 2007 by Strathdee, Gotts and McEachern, there have been no new developments to replace the industry standard asphaltene-based carcinogenic extenders. This situation first of all results from the experimental problems that arise when water-soluble minerals like sylvite are to be tested in saturated brine. Both oils and longchain amines are water/brine insoluble. The oil with the amine dissolved in it can however be emulsified and then used as an extender oil. Such oil droplets must wet KCl particles and the emulsion must be stable to avoid handling problems. In this paper we test the use of the phase inversion technique as a method of studying wettability of KCl particles by the oil in saturated brine, and the effect of amine dissolved in this oil on the wettability. The results show that this relatively simple technique can be used to characterize the wettability of fine KCl particles by the tested oil and to determine the effect of added amine on it, and so it can be useful in selecting proper extender oils.

Jan 1, 2016

By Roberto Pimentel de Souza

Since 1976 CVRD is carrying out tests to develop a type of pellet made with organic binder. One binder that showed good possibility to be used in industrial plants is Peridur. An extensive framework of tests was run in CVRD's pilot plant. The results are presented in this paper. Finally, the decision was taken to carry out an industrial production of 50.000 t of pellets. It was scheduled for March '81. The results are shown in this pager. It was not observed any detrimental effect of the peridur neither in the process nor in the product quality.

Jan 1, 1981

By David E. Peterson, F. Merz

The Waihi Gold Mining Company Limited, Martha Hill Project was the first major hard rock mining operation following the resurgence of the mining industry in New Zealand. Because of its location adjoining a town and at the southern part of the sensitive Coromandel Peninsula, the operation received a high level of public scrutiny. Very srrict limits for effluent criteria had to be met and led to the necessity for advanced wastewater rreatment technology. The process technology selected was the copper catalysed oxidation of cyanide using hydrogen peroxide, with subsequent removal of heavy metals by precipitation and filrration. This paper discusses the adoption of environment limits together with the detailed description of the plant and design criteria. Data of the one year's operational history is also presented.

Jan 1, 1991

By Tom Shumka

"All mineral processing facilities that use girth gear driven mills need to inspect the gear teeth on a routine basis, whether it be every six months to every three years. The inspection frequency depends on gear tooth condition, and the objective is to ensure the operational integrity of the gear teeth. Conventional methods such as magnetic particle testing, visual inspection or dye penetrant examinations rely heavily on operator interpretation. At best, these techniques can determine whether a defect exists, but are unable to provide information on defect severity. This paper describes the use of combining combined eddy current array (eca) and alternating current field measurement (acfm) to provide a complete survey of all surface breaking indications on the whole gear tooth depth. This method accurately determines the size, length and depth of any cracks found on the surface.INTRODUCTION In order to gain a fundamental understanding of the evolving operational and production behavior of a piece of machinery over a specified time period as part of an effective condition monitoring program, a robust data collection process must be firmly established and adhered to. To be effectively implemented within an organization, a condition monitoring program must have support of not only the maintenance, production and engineering staffs, but also executive management support to ensure successful roll out to realize the maximum productivity of the machinery and subsequent cost-savings. One of the key elements of a mineral processing facility that use gear driven SAG Mills as a primary stage for grinding solution, is the integrity of the critical gear unit that drive the mill. For the maintenance team, condition monitoring on the gear unit is crucial for preventative maintenance. A catastrophic failure in the critical gear unit would require a minimum of ten days to replace the gear set, depending on the damage occurred. This, of course, would only be applicable if the client had a spare critical gear set in inventory. If a gear set had to be ordered, it could take from four months to two years to receive a new gear set. For example, in 2007, there was a global backlog of these types of gears sets resulting in a two year delivery. The maintenance costs associated with a catastrophic failure of this type would easily cost in the millions."

Jan 1, 2012

By Ruifeng Li, Yanghui Ren, Hua Gao

"Since entering the new century, China’s coal industry has witnessed the rapid development, and provided a reliable energy supply for the national economic and social development. But after the “golden decade” of rapid development, the coal industry now is facing overcapacity, low industrial concentration and production efficiency, high pressure of production safety and environmental protection and other prominent issues. Based on defining the connotation of highly-efficient recovery of coal resources, this paper established the relevant 8 indicators to reflect the highly-efficient recovery level of coal resources, summarized the present situation of China's coal resources recovery and the main problems, analyzed the development environment of China's coal industry under the new situation, and finally put forward the strategic measures to promote highly-efficient recovery of coal resources in China.1. Background Coal is the main energy in China. Since entering the new century, China's coal industry has made significant progress, and the level of production safety, resource recovery rate and mining mechanization increased significantly, which provided a reliable energy supply for the rapid development of the national economy. However, due to the changes of China's economic environment, slow growth of energy demand and other factors, some prominent contradictions in the coal industry have significantly restricted the healthy development of the industry. The first problem is serious overcapacity. In the past few years, 16 industries including coal, electric power, chemical and others have invested in coal mines. It is reported (Han 2016) that only during the nine years from 2005 to 2014, the fixed assets of coal industry increased totally more than 3.3 trillion RMB, which brought a large number of production capacity. Affected by the slowdown of economic growth and energy structure adjustment, Chinese coal demand has reached the peak platform and caused the overcapacity of coal supply, so shutting down the backward capacity is the most important task in the future. The second problem is the low efficiency of coal production. There are about 4.3 million coal mine workers in China, and the annual coal production per capita is less than 900 tons, while it was reported (EIA 2016) that the annual production per capita in the United States is more than 10 thousand tons. The third problem is that the green coal resources are not rich. Among the 1.53 trillion tons proven reserves, only about one third are green coal resources in accordance with the principle of ""safety, technology, environment and economy"". The coal resources with high quality and easily mining conditions are not abundant."

Jan 1, 2017

By James E. Myers

This study is a survey of the current "state-of-the-art" of commercially-available sonar tools to monitor the true shape of man-made cavities within the Hutchinson Salt of south-central Kansas. The work entailed ferreting out the available information, most of which is proprietary in nature; then examining actual existing conditions and arriving at a reasonable scientific evaluation of the method. Our studies were confined to one LPG field and two brine well operations in south-central Kansas. No field testing of any devices was performed, only questioning user firms, and studying cores, logs, and sonar surveys graciously made available by the companies we have contacted. Since these data are still somewhat proprietary, the company participants have asked that their company names be omitted from this presentation.

Jan 1, 1973

By William Copp

THE SEAL BEACH oil field is between the Long Beach and Huntington Beach oil fields, south of Los Angeles, and about half the productive area is with-in the city limits of Long Beach. The proved area lies in portions of Sections 2, 3 and 11, T. 5 S., R. 12 W., S. B. B. & M. Seal Beach is 'an additional link in that remarkable chain, of oil fields extending from Newport to Beverly . Hills, filling in one of the few remaining gaps. It differs from other fields along this line of folding in that it is an oil field in an area of tide lands. Ocean-connected sloughs have access to this area, which ac-counts for its extensive mud flats. The surface eleva-tion of the low ground varies from 2 to 5 ft. above sea-level. This condition called for much preliminary work in building roads prior to field development. Roads are constructed with dredges and drag-line scrapers, which excavate mud from alongside the proposed road and pile it up to a grade high enough to be above high tide. The road bed is then surfaced with gravel, or decom-posed granite, which makes it serviceable in all kinds of weather. An immense amount of road material has already been hauled into this field. Well locations are staked in the mud flats, sometimes ahead of road build-ing, and material is dragged to its place on the ground by tractor. It is necessary to drive piling to support derrick foundations. The present practice is to drive 5 piles for each derrick leg, 4 under the rotary table, 2 under the draw-works, 2 under the Samson post and 4 under the pipe rack, a total of 32 piles. This pro-cedure is, of course, varied to suit special conditions, using either more or less piling.

Jan 6, 1927

Objective To accurately measure very low air velocities (0-100 ft/min) in U.S. large-opening underground metal/nonmetal mines. Background Hundreds of metal/nonmetal underground mines operate throughout the United States. They extract commercial products from deposits such as limestone, salt, and gypsum. Mining generates a wide variety of gases and dusts, such as silica, diesel exhaust, radon, blasting byproducts, and perhaps even methane. If these substances become airborne, they can adversely affect the health and safety of underground workers. Many metal/nonmetal mines have large cross-sectional airways that could be 60 times larger than an average underground coal mine entry. These large airways require adequate volumes of fresh air to dilute, make harmless, and exhaust the toxic and, at times, explosive byproducts. However, in some underground mine sections, air movement is barely perceptible. The technology of measuring very low air velocities will become increasingly more important for operators of large-opening stone mines in order to monitor miner exposure to diesel particulate matter. Conventional anemometers (e.g., vane) are capable of accurately measuring air velocities only above 100 ft/min. Thus, it was necessary to investigate other anemometry technology to detect low air velocities in the range of 0-100 ft/min. Two different portable ultrasonic anemometers were tested. Actual testing was done in an underground limestone mine with openings about 51 ft wide by 29 ft high. Ultrasonic Anemometers Vane-type anemometers are commonly used by engineering personnel throughout the underground coal mine industry. They work well in measuring air velocities >100 ft/min. However, a separate technology, e.g., portable ultrasonics, is needed to measure air velocities much below 100 ft/min at various places within the large mine opening. Laser-doppler technology was also considered for this application, but was ruled out because of its high cost and other technical limitations. With no moving parts, the portable ultrasonic anemometers are claimed to be accurate down to about 1or 2 ft/min. The first type of ultrasonic anemometer that was examined underground is manufactured by Gill Instruments Ltd., Hampshire, U.K. The U.S. distributor is IN USA, Needham, MA. The Gill Instruments Solent Volometer (figure 1) is a battery-powered, single-axis anemometer meant for measuring low to medium air flows up to1,999 ft/min. It uses the ultrasonic "time of flight" principle where pulses of high-frequency sound are transmitted along the air flow path and the time taken to reach the receiver is measured. The faster the air speed, the quicker the pulses reach the receiver. The second ultrasonic anemometer that was examined under-ground is manufactured by Airflow Developments Ltd., Buckinghamshire, U.K. The U.S. distributor is Airflow Technical Products, Inc., Andover, NJ. The Anemosonic UA-6 (figure 2) is a battery-powered, handheld instrument with digital display. It measures air velocity (0 to 9,999 ft/min) or volume flow, flow turbulence intensity, and air temperature. Neither device is considered to be intrinsically safe for use in underground gassy coal mines. A comparison of salient specifications of both instruments is shown in table 1. The total suspended weight includes the instrument (Gill) or instrument probe (Airflow) plus about 35 ft of connecting cable attached to the pole. This combination of instrument plus cable length allows two operators to measure air velocities up to about 30 ft above the mine floor. Figures 1 and 2 show how each unit would be attached to an extensible, graduated fiberglass rod in order to position the sensor probe at a certain spatial point (centroid of the quadrate) within the underground large opening.

Jan 1, 2003