Search Documents

By J. L. Lehman, J. D. Sudbury, J. E. Landers, W. D. Greathouse

A full scale field experiment on cathodic protection of casing answers questions concerning (1) the proper criteria for determining current requirments, (2) the amount of protection provided by different currents, and (3) the transfer of current at the base of the surface pipe. Three dry holes in the Trico pool in Rooks County, Kans., were selected for cathodic protection tests. The three holes were in an area where casing failures opposite the Dakota water sand often accur in less than a year. Examination of the electric togs showed the wells to be similar to other wells in the field where casing in four of seven producing wells has failed. The three holes were cleaned out and cased with 75 joints of new 51/2-in. 14-tb J-55. Each joint was visually inspected and marked before it as run. The casing was bull plugged and floated in the hole 50 that the inside might remain dry and free of excessive attack. Also, if a leak occurred, a pressure increase could be observed on gawge at the surface. Extensive testing was done, including potential profiles, log current-potentid curves and electrode measurements from both surface and downhole connections. Based on these data, a current of 12 amps was applied to one well and 4 amps to mother. The third well was left to corrode. During the two-year period when the casing was in the ground, [he applied current was checked weekly, and reference electrode measurements were made about every two months. Three sets of casing potential profi1e.c were run. When the three strings were pulled, each joint was examined for type of scale formed, presence of sulfate-reducing bacteria, extent of corrosion nttnck and pit depth. Since the pipe was new when run, quantitative determination of the protection provided by current was possible. This is the first concrete field evidence to help resolve the many arguments about the proper method for selecting adequate current for cathodic protection of oilwell (-using. INTRODUCTION A casing string is run when a well is drilled. This pipe is supposed to protect this valuable "hole in the ground" for the life of the well. Often the casing does not last the life of the well; it is with these casing failures that this work is concerned. The cost of repairing a casing failure varies from field to field—from as much as a $30,000 per leak average in California to $5,000 per leak in Kansas. Additional costs other than actual repairs are also important. These include formation damage, lost production, etc. Casing damage caused by internal corrosion is important in some areas. Treatment normally consists of flushing inhibitor down the annulus, but further research is being done on control measures. The test described in this paper is concerned only with external corrosion. The problem of casing failure from external attack has appeared in several areas including western Kansas, California, Montana, Wyoming, Texas, Arkansas and Mississippi. Cathodic protection is currently being used in an attempt to control external corrosion. From reports in the NACE there are thousands of wells currently under cathodic protection. The quantity of current being applied ranges from 27 amps on some deep California wells to a few tenths of an amp being supplied from magnesium anodes on wells in Texas and Kansas. Considerable field and laboratory effort1,9,5,6 was exented on the problem of cathodic prctection of casing, and it became fairly obvious that this method could be used to protect wells. Early workers showed that current applied to a well distributed itself over the length of the casing and was not concentrated on the upper few hundred feet. Basic cathodic protection theory had shown that corrosion attack could be stopped by applying sufficient current. The problem resolved itself, then, into one of trying to decide just how much current was necessary. Various criteria were utilized in installing the many existing cathodic protection installations. These methods included the following. 1. Applying sufficient current to remove the anodic slope as shown by the potential profile." 7. Applying enough current to maintain all areas of the casing at a pipe-to-soil potential of .85 v.' 3. Applying the current indicated by a log current-potential (or E log I) curve." 4. Supplying the current necessary to shift the pipe to-soil potential .3 v." 5. Applying 2 or 3 milliamps of current per sq ft of casing."

By J. D. Pennock

About a year and a half ago, Mr. Morris, an engineer of the Solvay Process Company, was sent to Belgium and France to study the manufacture of coke in the Semet-Solvay ovens, which were in operation at Havre. With complete plans of construction and a good understanding of the methods of running the ovens, he returned to Syracuse. Work on twelve Semet-Solvay ovens was immediately begun. These ovens, with plant for crushing and washing coal, and the necessary condensers, scrubbers, and concentrator for the recovery of the byproducts are nearly finished, and will soon be in operation. As the work approached completion it became necessary to determine what coal should be used. Accordingly, a chemical investigation of the various bituminous coals was made. I. Investigation of Coals. The samples of coal taken for analysis were: I. A sample of Reynoldsville coal that had been exposed to the weather for a year; 11. Reynoldsville coal taken from a car direct from the mine; 111. Morris Run lump coal; IV. Morris Run fine coal; V. Coal from the Fairmount Coal and Coke Company; VI. A special enginecoal from Pardee colliery, Phillipsburg, Pa.; VII. South Fork, Pa., coal; VIII. Coal from Laceyville, Ill.; IX. Pittsburgh bituminous coal from Ocean mines (gas-coal); X. Steubenville, Ohio, coal; XI. Evansville, Indiana, coal; XII. Coal from the Ohio Coal Company. Proximate Analysis. I. 11, 111. IV. V. VI. Water at 90° C.,* ..................................... Volatile,. .. 31.14 33.00 17.73 18.12 37.20 23.86 Fixed Carbon,. . 64.49 58.07 71.92 71.89 56.68 73.00 Ash,. .. 4.37 8.93 10.35 9.99 6.12 3.14 Coke,. .. 68.86 67.00 82.27 81.88 61.88 76.80

Jan 1, 1893

By W. P. Sykes

IN CONNECTION with a study of tungsten steels, Honda and Murakami1 reported an investigation of the system iron-tungsten. This report included a tentative equilibrium diagram, photomicrographs of various alloys in the series, and qualitative measurements of hardness and magnetic properties. The present investigation originally had as its object the study of the hardness and tensile properties of a series of carbon-free iron-tungsten alloys. But, as the work progressed it became evident that the system possessed other features of interest, so the scope of the investigation was enlarged. MATERIALS The iron powder used in preparing the alloys was obtained as follows: Iron oxalate was precipitated from a ferrous-sulfate solution by the addition of a solution of oxalic acid. This oxalate, after thorough washing, was ignited to iron oxide, which after reduction in hydrogen at about 1000° C. yielded iron powder containing but about 0.2 per cent. iron oxide and about 0.005 percent. carbon. Tungsten metal in the form of powder, such as is used in the manufacture of filaments for incandescent lamps, was the other constituent. This material analyzed 99.8 per cent. tungsten and contained no carbon, The metal powders, in the desired proportions, were mixed by tumbling and formed, under pressure of 20 tons per sq. in., into rods 3/8 by 3/8 by 10 in. To form the alloys without contamination, sections of the pressed rods were placed on alundum slabs and heated in an alundum tube wound with a tungsten resistor and packed in heat-insulating material. While the resistor was heated, a stream of hydrogen was continually passed through both the tube and the case containing it. The tungsten winding on the tube, as well as the material heated within the tube, was thus protected from oxidation. Such a furnace will operate constantly

Jan 2, 1926

By M. F. Williams, L. G. Hendrickson

IN classification of pulps bearing magnetized ferromagnetic particles, depolarizing is of great importance. If size separation is to be effective, particles must be individual rather than in floes. Depolarizing is also practiced in heavy medium separations in which ferrosilicon or magnetite is the medium. When particles of ferromagnetic material have been removed from a magnetic field, residual magnetism causes agglomeration. The term depolarizing refers to the operation of reducing or eliminating this residual magnetism and may thus be considered magnetic deflocculation. The terms demagnetizing and randomizing are also used. At the Research Laboratory of Oliver Iron Mining Div. in Duluth a method was developed for measuring depolarization of the pulp of ferromagnetic material. Experiments were made with Mesabi taconite,' a natural magnetite of low coercive force. Ferromagnetic materials of higher coercive force, such as lodestone or the artificial magnetite produced by reduction roasting of hematite, present a more difficult problem, which was not within the scope of this investigation. It is possible, however, that some of the techniques evolved for measuring and calculating electrical characteristics of alternating current coils would be of use in depolarizing high coercive force material, particularly in conjunction with high-frequency alternating current, as proposed by Hartig and others.'," Properties of Ferromagnetic Materials:'7 Experimental work, described below, has shown that if a sample in the magnetized state is heated above the Curie point and cooled, much of the preferred orientation is destroyed and the sample is substantially depolarized. It has been thought that when the sample cools below the Curie point the domains cancel each other, leaving a zero net moment. However, such particles still exhibit a tendency to cohere, and undoubtedly this is caused by the forces of residual magnetism. -AS measured by the percent depolarization, this tendency is reproducible for any sample upon repeated heating above the Curie point and subsequent cooling and is independent of the initial state of magnetization. It is postulated, therefore, that as the material is cooled below the Curie point the domains in any particle do not completely cancel each other, but rather are preferentially oriented to some extent. Mechanism of Depolarizing with Alternating Current Magnetic Fields: It is believed that when ferromagnetic material is passed through an alternating magnetic field, depolarizing occurs in the decaying portion of the field. As the particles pass through the portion of highest intensity they become magne- tized. If the particles are not free to move, the polarities of the particles will be reversed (by a mechanism similar to that described above for magnetism) at a frequency equal to that of the applied field. As the material moves through the decaying field, intensity levels become such that a domain does not completely reverse, but stops on an axis of easy magnetization. By the time the material reaches the point of zero field intensity, a state of fairly random orientation of domains is achieved. If conditions are such as to give a completely random orientation, the particle will have little or no external magnetic field, and a pulp of such particles will be depolarized. Previous Work In 1918 E. W. Davis was granted a patent for demagnetization of magnetite pulps.' His method consisted of passing the pulp through a tapered coil, activated by alternating current of normal frequency (60 cycle). This method, with minor modifications, has been used almost universally in all pilot plants and commercial installations in which depolarization of low coercive force materials has been required. Hartig, Onstad and Foot2,3 avd made a detailed study of the factors involved in depolarizing both low (below 100 oersteds) and high (above 100 oersteds) coercive force material. They developed a method for evaluating the relative degree of depolarization of any pulp based on the settling characteristics of the pulp. Their standard of comparison was a sample heated to above the Curie point and cooled in a zero field, all in a neutral atmosphere.* For low coercive force material they found treatment.Thisprocedure is subsequently called, in this report,theCurie that results equivalent to Curie treatment could be

Jan 1, 1957

By Robert Hopler

209. Nitro-glycerine is produced by the action of nitric and sulphuric acids on glycerine, and is a heavy liquid of oily appearance, of specific gravity about 1•6, varying from colourless when quite pure to a yellow or brownish yellow. It is of a very sweet taste, and without odour, and is an active poison. Mere handling of it will in most persons induce sickness and headache. It explodes when heated to about 360° F. or from shock, but in small quantities it ignites and burns with some difficulty by the mere contact of flame.

Jan 1, 2011

By Daniel R. Hack

This paper point out the development of optimized routines for the processing and analysis of field data, continually building a framework for further software development. It also describes the possibilities for future development in the realm of 2D variography for surface water heat flow systems using existing proprietary and academic software packages.

Jul 17, 2000

By R. L. Rickett, W. C. Leslie, W. D. Lafferty

Notch toughness of 0.10'pct C steels, rimmed or killed, is improved by holding the steel at a temperature just above the Ae,, followed by air cooling. The improvement can be gained without apparent change in gross microstructure or hardness. The limits of the process have been determined and some possible reasons for the observed effects are discussed. The results appear to indicate that the current theories of transition temperature are inadequate. THE effects of gross microstructural variables (ferrite grain size, austenite grain size, type and distribution of carbides) on the notch toughness of mild steels have been the subject of many investigations.'-' The results indicate that increasing ferrite grain size raises the notch-impact transition temperature. The transition temperature also rises with increasing size of pearlite colonies and with increasing prior austenite grain size, but these factors are not independent of ferrite grain size. The effects of gross composition of steels have also received considerable attention. As a result, manganese, nickel, aluminum, and silicon are known to improve the notch toughness of mild steels. The other elements that have been investigated—carbon, nitrogen, boron, copper, chromium, molybdenum, phosphorus, sulfur, titanium, and vanadium—reportedly are either deleterious or have little effect on notch toughness. Despite this large volume of work, it is still not possible to predict the notch toughness of a mild steel from its microstructure and composition, even when these are supplemented by hardness and tensile tests. Steels with equivalent microstructures, but different thermal and/or mechanical histories, can differ in notch toughness. Such factors as type and distribution of precipitates, substructure, local variations in composition, or unrecognized variables, may be important in determining the notch toughness of mild steels. However, quantitative knowledge of the effects produced by these factors is almost completely lacking. In an effort to improve this situation, an investigation was begun to determine the effect of a very fine precipitate on the notch toughness of low-carbon steels. Aluminum nitride was chosen as the precipitate because of its presence in aluminum-killed steels, the ease of control of precipitation, and past

Jan 1, 1961

By G. W. Cutting

Interlocking material balances on complex mineral dressing plants greatly assist in metallurgical investigations: indeed, without such a balance, there is no firm basis upon which to base process performance evaluations. To achieve balances both qualitative and quantitative data must be rationalised in conjunction with the process flowsheet. WSL has developed a range of programs to evaluate interlocking material balances. However, to obtain maximum benefit from the balances, answers of direct value at the process level must be provided: WSL has developed also a range of programs for this purpose. Practical examples are given, which illustrate the benefits obtained from process balances.

Jan 1, 1979

By I. D. Schleicher, L. H. Rorden, F. B. Curry, T. C. Moore

The purpose of this program is to extend electromagnetic (EM) techniques for use in locating miners trapped in mines as deep as 1000 m. A previously developed EM system is considered adequate for use at mines less than 300 m deep where it has a probability of detection of 54%. A system for deep mines must keep underground equipment simple, and use extremely low frequencies (ELF), sensitive receivers, and noise cancellation. The proposed location method, developed by Develco for other applications, is based on vector field measurements from two or more static sensors and computation of source location by iterative techniques. During Phase II, very sensitive search coil sensors were built and used in a separate test to verify the feasibility of atmospheric noise cancellation. A "Breadboard" location system version without cancellation, which is a fieldable test bed to evaluate receiving and location functions, was tested and supplied. Very good results were achieved from the first in-mine test with the transmitter at a depth of 380 m. It is expected the results of this work, and additional evaluation tests in the future, will be used to define the requirements for a prototype operational system.

By V. A. Feofanov

Technogenic water of ore mining enterprises, nonferrous metals operations, the enterprises of electroplating and instrument making, containing copper in the form of those or other connections can serve as perspective sources on receiving the copper-bearing raw material. Extraction of copper from the given water also solves a problem of water treating from a toxic component that reduces environmental load at evacuation of water in an open basin. The method of case hardening allows extracting copper selectively with reception of a deposit with the content of copper up to 70%. Weakness of the method is its efficiency basically in acid reduction, and also its low degree of copper extraction. On the basis of case hardening the method of galvanic coagulation is devised. It is based on the work of a short-circuited galvanic cell of iron-coke at variable contact of coupled metals components among themselves, cleared by the oxygen of air. The following processes of galvanic coagulation are considered: ? Extraction of copper; ? Formation ferrites of copper; ? Copper sorption on just-aggregated oxide forms of iron. Establishing conditions for passing the given stages provides an opportunity of copper extraction from technogenic water at any value of ??, content of salt and concentration of copper with reception of a compact deposit from which it is possible to extract copper by the known ways of enrichment and metallurgy. Investigations on optimization and intensification of galvanic coagulation with the purpose of reception the maximum rich deposit on copper have shown that the average contents of copper in a solution of 100~200 mg/dm3 the contents of copper in a deposit is 6%~10% at extraction 85%~90%, depending on characteristics of treated technogenic water. Using methods of scanning microscopy it is determined structures, composition and mechanism of phase formation in investigated electro-chemical process. The second stage of galvanic coagulation increases a degree of copper extraction up to 98%~99% that allows returning the cleared waters in circulation for waste recycling or evacuation in an open basin. Nowadays the method of galvanic coagulation is the most acceptable for copper extraction from technogenic water both from the point of view of efficiency and instrument setting that allows applying the method in conditions of the working enterprises.

Jan 1, 2014

By R. Q. Shotts

Nitric acid oxidation rate analyses of three coals, previously studied microscopically by the Bureau of Mines, revealed three components. Relative quantities agree with those found for the four components given by the Bureau and results are consistent with current ideas of coal constitution. Possible multi-component composition for bright coal and a reactivity-rank relation are suggested. THE physically dissimilar components of bituminous coals often are easily recognized mega-scopically. Under the microscope, reflected light or light transmitted through thin sections reveals the presence of the different components, even when these are intimately mixed. Optical methods for the quantitative estimation of the relative abundance of the various components, both by means of thin sections and by particle count, have been fully described.'. ' It has long been recognized that there are chemical and physical differences between the various petro-graphic components of bituminous coals, although analytical differences usually are small.:'. ' Only in the case of fusain have chemical differences been used for quantitative determination of a component. C. C. Hsiao and associates, at the Mineral Industries Experiment Station of the Pennsylvania State College, have described a method of analysis which is based upon the differences in the rate of nitric acid (8N) oxidation, fusain, and the other components of coal."," The reproducibility of their method and its applicability in checking microscopic determinations of fusain content have been supported by several independent investigations.'. " The writer has proposed the use of differences in oxidizability for the estimation of other components." "' The results of the oxidation of whole coals and of float-and-sink fractions of coals were reported. In most cases the plots of the logarithms of the percent dry, non-fusain, organic residue from oxidation, against time, revealed the presence of at least two distinct components. Both components appeared to oxidize according to a first order law, but the reaction constants for the components were distinctly different. One or more of the dull density fractions were found to contain but one component, and some of the lower rank coals oxidized in such a way as to suggest the presence of three components. A suitable way to check the identity and significance of the components delineated by oxidation would be to analyze a sample of coal both by the nitric acid oxidation procedure and by a microscopic method. The writer was wholly unfamiliar with either of the microscopic techniques commonly used, and to make such a comparison it was necessary to rely upon microscopic analyses made by someone else. It is hoped that some laboratory which is equipped to make both types of analyses will some day make them upon identical samples. During the past 20 years, four Alabama coals have been analyzed petrographically and the results published by the United States Bureau of Mines. They are: 1—Flat Top mine, Mary Lee bed; 2—Empire mine, Black Creek bed; 3—Wylam No. 8 mine, Pratt bed, all in the Warrior field; and 4—Soot Creek mine, Fairview bed, in the Coosa field."-" Of these, only the Flat Top mine is still operating. Because of the closing of these mines, it first appeared necessary to rely upon the indirect and unsatisfactory procedure of sampling the beds in other mines located as near to the closed mines as possible. Upon investigation, however, it was found that the Bureau of Mines still had, in storage, the very same samples which had been used in the published petrographic studies. The Bureau very generously furnished about 2000 g each of the Pratt, Mary Lee, and Fairview bed coals, largely lumps but with some fines. The blocks of coal, when received, still were covered by the paraffin coating which had been placed on the polished surface, in the case of the Mary Lee coal almost twenty years ago. Procedure The procedure for oxidizing the coal sample and removing the alkali-soluble humic acid has been described. In the present study, oxidation periods of 1/6, 1/3, 1/2, 3/4, 1, 2, 3, and 4 hr were used. All oxidations were made in triplicate. After the paraffin had been removed in boiling water and the coal washed carefully with cold benzene, the entire sample of approximately 2000 g, obtained from the Bureau of Mines, was crushed to pass a No. 4 sieve. About 200 g of this material was pulverized to pass

Jan 1, 1954

By R. W. Coughlin, W. U. Ault

Experiments in laboratory and mine have clearly demonstrated the usefulness of radioactivity detection for directly measuring the potassium content of potash ore as mined. This paper presents the results of these tests and documents the design of a system for automatically grading and sorting potash ore on the basis of radiation detection. It is shown how the experimental results in the subject mine lead directly to the design of this kind of an automatic control system. The system is capable of grading the ore with an accuracy of approximately ±2% K20 content or better. Due to the usual stratification of the ore body, mining potash seldom presents an extreme problem of gangue separation. Nevertheless, it is frequently necessary to transport within a potash mine and even hoist to the surface considerable quantities of halite and other valueless materials. Up to recent times it has been customary to recognize and route these materials by simple visual and manual techniques. However, the work reported here clearly demonstrates that it is now practical and economical to improve upon these techniques by continuous measurement1 of the naturally occurring radioactive isotope, potassium-40. It was the purpose of the work reported here to investigate this technique and assess its applicability. LOCALE OF EXPERIMENTS The work described here was carried out in a potash mine in Carlsbad, N.M. At the working face of this mine the potash ore is freed by blasting; it is then transported a short distance by shuttle car to a moving-belt system which conveys it to the main shaft where it is hoisted to the surface. Quantities of gangue which are also produced in the mining operation are disposed of in mined-out sections of the mine where possible. Otherwise, this material which contains only a small percentage of potassium (as K2O) must also be transported by the conveyor-belt system to the main shaft and then hoisted to the surface and discarded. With this situation, any measuring device for automatic control purposes must be capable of clearly distinguishing between gangue containing insignificant amounts of K2O and ore containing larger percentages of the same mineral. The conveyor-belt system transports the material from the mine face to a rotary crusher and then to temporary storage pits at the main shaft. This is shown in Fig. 1. Upon leaving the conveyor belt the material enters either one of the two storage pits according to the position of a manually operated gate. It was decided that all experiments should be carried out at the conveyor belt between the crusher and gate with a view to the possibility of providing a signal which could operate the gate automatically. THEORETICAL BASIS AND LABORATORY EXPERIMENTS In principle it is possible to grade potassium-bearing ore on the basis of radioactivity. Natural potassium contains 0.012% K40, which is radioactive with a half-life of 1.3 x 10' years. Although about 89% of the K40 disintegrates to Ca40 by beta decay, the other 11% changes to Ar40 by electron capture and the emission of gamma rays. Unlike the ß-rays which are readily absorbed in the first few millimeters of ore surrounding the disintegrating nucleus, the y-ray photons will escape from an ore sample several inches in size. A detector rigidly mounted under a conveyor belt loaded with potash ore will intercept some constant fraction of all the photons emitted from the ore within its field of view. Under these

Jan 1, 1968

By George Stern

The purpose of this investigation has been to study one method for making ordinary carbon steel by the powder metallurgy technique. This method con- sists of pressing and subsequently sintering an intimate mixture of iron powder and gaphite in a suitable atmosphere to Produce a steel. Two types of iron Powder have been studied, electrolytic and reduced. The sinkring of mixtures of loose Car-bonyf iron and carbon black for several hours at I000 to 1100 C. (1830' to 2010°F.), followed by forging of the resultant ingots to bars, has been studied by Offermann.' TrailZ has reported on the properties of hydrogen-reduced and electrolytic iron powders, both containing 0.5 per cent carbon. Methods for making steel bodies by powder metallurgy have also been sug- gested by Goetzel13 who recommends the addition of steel powder of well-defined carbon content to pure iron powder, and Volterra,~ who suggests compaction and subsequent sintering of a mixture of steel powder, iron oxide and iron powder. Additional methods for making steel bodies by powder metallurgy have been reported in the literature by Kohering Allen,6 Balke,7 Wulff,8 Boegehold,9 and others.,0,11,12 It is felt that the method of pressing iron powder and graphite, as described herein, lends itself best to production be-Cause of the lubricating action of the

Jan 1, 1946

By George Stern

The purpose of this investigation has been to study one method for making ordinary carbon steel by the powder metallurgy technique. This method con- sists of pressing and subsequently sintering an intimate mixture of iron powder and gaphite in a suitable atmosphere to Produce a steel. Two types of iron Powder have been studied, electrolytic and reduced. The sinkring of mixtures of loose Car-bonyf iron and carbon black for several hours at I000 to 1100 C. (1830' to 2010°F.), followed by forging of the resultant ingots to bars, has been studied by Offermann.' TrailZ has reported on the properties of hydrogen-reduced and electrolytic iron powders, both containing 0.5 per cent carbon. Methods for making steel bodies by powder metallurgy have also been sug- gested by Goetzel13 who recommends the addition of steel powder of well-defined carbon content to pure iron powder, and Volterra,~ who suggests compaction and subsequent sintering of a mixture of steel powder, iron oxide and iron powder. Additional methods for making steel bodies by powder metallurgy have been reported in the literature by Kohering Allen,6 Balke,7 Wulff,8 Boegehold,9 and others.,0,11,12 It is felt that the method of pressing iron powder and graphite, as described herein, lends itself best to production be-Cause of the lubricating action of the

Jan 1, 1946

By Yuexin Han, Jie Liu, Shuai Yuan, Yanjun Li

"In order to improve recovery efficiency of iron minerals from iron ore tailings and to reduce its connected environmental pollution, this article investigated the reducing roasting of iron ore tailing in a laboratory fluidized magnetization roasting reactor to optimize the roasting method and conditions. The examined parameters included roasting temperature, roasting time and reducing atmosphere. The parameters evaluating magnetizing roast efficiency and theoretical value were determined. X-ray diffraction (XRD) analysis was used to investigate the conversion of iron phase after roasting. The results show that the best magnetizing roast conditions are roasting temperature of 540?, holding time of 15min, and CO concentration of 20%. The magnetization conversion ratio of roasting products is over 80%, under the best magnetic separation condition, the concentrate grade of iron is 65.61 % and the recovery of iron is 83.77 %. The XRD analysis shows that Fe exists in hematite and siderite before roasting and exists in magnetite after roasting. The technique not only recovers the iron minerals from tailings with good economic benefit, but also reduces the environmental pollution of tailings accumulation.INTRODUCTION Iron ore tailings are the solid wastes generated during the beneficiation process of iron ore concentration and are one of the main pollution concerns in the mining industry (Das et al., 1996). Continuous development of the iron and steel industry has led to the increasing amount of iron ore tailings; there are over 300 million tons of iron ore tailings discharged per year (Rao et al., 2016). The huge amount of stockpiled iron ore tailings brings a series of environmental and social problems. Comprehensive utilization of iron ore tailings can not only reduce environmental load but also conserve resources, promoting sustainable development of the society. In recent years, iron ore tailings as secondary resources have received considerable attention in many countries in the word and numbers of studies on utilization of iron ore tailings were carried out, such as recycling the valuable minerals (Datta et al., 1996; Jia et al., 2013; Panda et al., 2018), used in construction material compositions as alternative source of raw materials (Das et al., 2012; Zhou et al., 2012; Luo et al., 2016) and other utilization. The iron minerals were recovery by magnetization roasting (Rao et al., 2016; Yang et al., 2013; Yang et al., 2011) and flotation (Kumar and Mandre, 2016). By comparison the reduction roasting has more advantages, but it was found that the conventional roasting equipment was inefficient, high energy consumption and un-economically applied on an industrial-scale."

Jan 1, 2018

By E. W. Dean

This report on the physical and chemical properties of typical crude oils of Oklahoma is the sixth in a series of preliminary chapters of a bulletin covering the producing districts of the United. States. Preceding reports* may be obtained on request. The details of the methods used in this survey in collecting samples, making laboratory tests, and interpreting results are discussed in the first three papers. If any errors or omissions are noted by readers, it is hoped they will be brought to the attention of the Bureau of Mines for correction before the appearance of the permanent report. Samples of Oklahoma crudes analyzed in this report were taken from those fields representing the major production of the State. The Oklahoma Geological Survey designates 172 different oil and gas fields in the State, S1 being in Osage County, 14 in Tulsa County, 14 in Okmulgee County, 9 in Washington County. The list of samples collected by the Bureau of Mines represents only 5 fields in Osage County - Bigheart, Burbank, Hominy, Osage Junction, and Pershing - yet these samples, together with those from adjoining fields, are representative of nearly all crude produced in the county. The sample 'from the Pershing field, for example, is representative of the crude produced in several fields in that part of the county - such as Nelagoney, Pawhuska, Wyomona - and the sample from the Skiatook,

Jan 1, 1922

By J. P. Wilson

The Tessenderlo-Kerley Leach process has been shown to be effective in the removal of residual copper from molybdenite concentrates. Concentrates of varying mineralogy, including those containing relatively large amounts of chalcopyrite, have been successfully leached on laboratory and pilot plant scales. The lixiviant system is ammonia and ammonium bisulfite with air / oxygen addition. An abrasive is added which greatly enhances the kinetics, and it is subsequently screened out and reused. The dissolved copper is easily recovered using existing technology. Extraction profiles, reagent consumptions, and mineralogical data are presented.

Jan 1, 1999

By ED. E. Furman, R. H. Atkinson

HITHERTO the practical creep testing of precious metals has received little or no attention. The only previous creep tests of precious metals have been made with wires under conditions such as to yield much more rapid rates of creep than in engineering tests.', ' Up to the present time the value of creep bars of adequate size, in the absence of real need for engineering data, has deterred investigators. However, the increasing use of platinum at high temperatures has demonstrated the need for reliable creep data for the guidance of engineers, especially those engaged in designing certain specialized chemical plant equipment. In order to supply this need, creep tests were conducted at 1382°F (750°C) on 0.290 in. diam specimens of platinum, 90 pct Pt, 10 pct Rh and palladium. The platinum was high purity, nominally 99.95 pct Pt. The 90 pct Pt, 10 pct Rh was of the same high quality as is used for making gauzes for the catalytic oxidation of ammonia. The palladium was also of high purity; two batches of palladium bars were tested, one deoxidized with calcium boride and the other with aluminum. Spectrographic examination of the palladium confirmed its good quality; the only significant impurities apart from the residual deoxidizers were traces of silicon and lead. Procedure The creep bars, which were furnished by Baker and Co. to our specification, were 6 ¾ in. in overall length with a 4½ in. (4 in. gage length) reduced section 0.290 in. in diam and had the ends threaded (?-NC16). It may be of interest that the bars were valued at up to $600 each. The specimens were supplied in a 50 pct cold-worked condition to facilitate attachment of the creep extensometer, which was of the push rod type. Because of the softness of the platinum and palladium, the extensometer rings were secured to the test section by means of circular knife edges instead of the usual pointed set screws. The extensometer rods extended through the bottom of the furnace and readings were taken with a 0.0001 in. "Last Word" dial gage fastened to the rods for the duration of the test. The bars were directly loaded by hanging weights from the lower specimen grip. All tests were conducted at 1382°F ± 2°F, and an effort was made to maintain the temperature gradient over the test section within 2°F. The ends of the furnace tube were packed with asbestos wool, which allowed a very slow circulation of air through the tube. Annealing was accomplished in the creep furnace before the load was applied. The platinum and palladium specimens were annealed at the test tem- perature for about 17 and 24 hr respectively; in the case of the rhodioplatinum it was found expedient to anneal for 1 hr at 1922°F (1050°C). Pilot samples cut from the same stock as the bars were used to check annealing procedures. Pertinent measurements of grain size and hardness were recorded. Results and Discussion The creep data obtained are given in Table I and the creep curves are plotted in Figs. 1, 2, and 3. Two platinum specimens, tested under a stress of 250 psi, had almost identical creep rates at 2000 hr, namely 0.000008 and 0.000009 pct per hr. A third platinum specimen, stressed at 400 psi, had a creep rate at 2000 hr of 0.000026 pct per hr; the reason for a rather sharp decrease in creep rate during the period from 1200 to 1600 hr is unknown. As it was thought that 90 pct Pt, 10 pct Rh would have a lower creep rate than platinum, the first sample was tested at 400 psi; however, the creep rate was approximately 50 pct greater. Microex-amination revealed that differences in grain size might be responsible for the unexpected result, as annealing at 1382°F developed an average grain diameter of 0.0021 in. in the rhodioplatinum specimen compared with 0.004 in. in the platinum bar. Annealing the alloy for 1 hr at 1922°F (1050°C) increased the average grain diameter to 0.0032 in. and materially improved the creep resistance, making it much better than platinum. A second specimen annealed at 1922°F (1050°C) and tested under a stress of 550 psi had a creep rate of 0.000022 pct per hr at 2000 hr, which was still substantially lower than that shown by the specimen annealed at 1382°F (750°C) and stressed at only 400 psi. In contrast to the creep behavior of the platinum and rhodioplatinum specimens, the palladium bars, whether deoxidized with calcium boride or aluminum, were characterized by high first stages of creep. However, after about 1200 hr of test, the creep

Jan 1, 1952

This paper presents a virtual prototype for the stress analysis of cable shovel components based on combination of flexible and rigid body approach. The general mechanical system of the cable shovel is modeled as a multi-body system with rigid and flexible bodies. The relevant theories applied for the dynamic model are described in terms of Lagrangian multi-body dynamics and finite element method. A virtual prototype of the cable shovel is built in the Automatic Dynamic Analysis Mechanical System (ADAMS) environment, which allows visualizing the motion of general mechanical system and analyzing the dynamic stress of structural components of the cable shovel. An example is given to perform dynamic stress of durability analysis for the boom and handle. Attention of this study is devoted to the mechanisms of damage of the cable shovel and also the critical high stress areas. Keywords: Cable shovel, Von Mises stress, Virtual prototype simulation, Stress virtualization.

Jan 1, 2009

By P Cherepanskiy, G Elphick, R Hus, C Perring

When an iron orebody nears its end of life, the extracted material can become increasingly problematic to handle. Higher moisture content occurs as larger portions of originally-below-water-table material is mined, which in some deposits is accompanied by further changes in physical and/or chemical properties present along the edges of the orebody. Plant delays related to problematic material have affected all of BHP’s mining hubs to various degrees. Following the recent successful work in Yandi, where the development of an index to quantify the handleability of channel iron ore deposits resulted in an increase in extracted volumes and an extension to the expected life-of-mine, the value of implementing similar indices for bedrock iron ore deposits has been recognised. A materials handling index has been developed by combining observed empirical relationships between material properties and processing plant performance. Indices for each deposit were further refined and optimised by implementing a back-testing strategy which facilitated an understanding of what weighting or scaling each of the contributing components should carry to yield the highest success rate of predicting actual delays at a given plant. Currently materials handling indices are deployed to all mine sites and are made available in block models as well as calculated for individual blasthole and production samples. Values in block models are obtained by predicting the required properties using machine learning models, whereas hyperspectral data is used to ‘measure’ some of those properties on a sample level. This paper discusses the work that has been undertaken to obtain materials handling indices, the testing that has been done to optimise them, and what processes have been developed to ensure the best metrics are being used in the different planning and scheduling horizons to optimise extraction.

Jun 22, 2022