Search Documents

By Valerio Violo, Antonio Raschillà, Livia Cicinelli

"The Cityringen project foresees the construction of a new circular metro line in and around the city center of Copenhagen. Both drives, the north and the south one, required the TBMs to be equipped in order to cope with contaminated water table and soil. The north drive mined in water contaminated with chlorinated compounds, including chloroform and vinyl chloride, while the south TBMs excavated in a highly benzene contaminated area, becoming the first TBMs to complete such a challenge. Despite the pollution and the stricter operative procedures, the production has been extremely successful with record up to 520 m in one month and 32 m in one day. 1 INTRODUCTION The Cityringen is an extension of the existing metro line. The 15 km long twin tunnels will form a new circular line with 21 new stations (17 + 4 crossovers). When finished it will interchange with the existing metro, rail and bus infrastructure at key locations around town, taking 90% of Copenhagen citizen at less the 600m from a metro station (Figure 1). The Contract has been awarded in April 2011 to the Copenhagen Metro Team (CMT), a joint venture between the Italian companies Salini Impregilo, Tecnimont and Seli SpA. Tunnels are being excavated with 4 Seli-Kawasaki EPB TBMs, two of which manufactured in Denmark by Seli Tunneling Denmark ApS, which is also operating them. At the moment this article is written 50% of the tunnels have been completed and over 40% handed over for the electromechanical works. Seli Tunnelling Denmark is a Danish company constituted in 2012 as a subsidiary of Seli SpA for this project and subsequently acquired by the Salini Impregilo Group in 2015."

Jan 1, 2016

By Amilton Feliciano Castro

In this work, activated carbons (ACs) were prepared using Sewage sludge as starting material. The ACs were pyrolyzed in an inert atmosphere at 550 °C after independent chemical treatment with ZnCl2 or KOH with ratio of 1:1. The materials were used as adsorbents for removal of Cu(II) from aqueous solutions. The adsorbents were characterized using adsorption/desorption nitrogen isotherm, SEM (scanning electron microscopy). The results showed that copper removal could be linked to surface pH and compounds present on the surface of adsorbent. KOH-treated adsorbent has smaller surface area (186 m2 g-1) than ZnCl2-treated adsorbent (192 m2 g-1), however, KOH-treated adsorbent exhibited higher removal of Cu(II). The performance of KOH-treated adsorbent could be attributed to the presence of basic groups on the adsorbent surface. Liu isotherm model gave the best description of the equilibrium data. From the Liu isotherm, the maximum adsorption capacities at 298 K for KOH-treated, ZnCl2-treated and sewage sludge (without inorganic activation) adsorbents are 31.85, 19.79 and 3.513 mg g-1, respectively. The best desorption experiment was obtained using 1.50 mol L-1 of HNO3 as eluent. Recoveries of Cu(II) from Cu(II)-loaded adsorbents are 98.9% (ZnCl2-treated) and 95.5% (KOH-treated.

Aug 17, 2017

By T. C. Davis

Nine organic derivatives of fluorine, silicon, boron, and aluminum were purified for thermodynamic studies using distillation, zone melting, and gas liquid chromatography, The unusual properties of these compounds required the development of special techniques for handling and purification. To determine purities of purified samples, new techniques for analyzing spectral data were developed.

Jan 1, 1965

By H. D. Hunt

This paper which describes the milling practice of the Miami Copper Co. is one of a series being prepared by the United States Bureau of Mines. LOCATION The mine, concentrator, and other surface plants of the Miami Copper Co. are located near the town of Miami in the Globe-Miami mining district of Gila County, Ariz.

Jan 1, 1932

By David K. Fountain

"The growth of the mining industry in British Columbia in the last ten years has been largely the result of the development of large low-grade copper and molybdenum deposits. There are two problems which must be solved in the search for mineral deposits of this type. It is necessary to detect large volumes of rock containing a low percentage of total sulphide mineralization1 and, secondly, to get some idea of the economic significance of this mineralization. The standard geophysical exploration techniques available have a varying degree of application in the search for disseminated sulphide de-posits. The electrical methods, and the induced polarization method in particular, are the most successful direct methods, and magnetic methods have indirect application in most situations. This is illustrated by geo-physical survey results from several properties in British Columbia."

Jan 1, 1968

By C. Kathryn Sole

The close proximity of cobalt and nickel on the Periodic Table and their frequent occurrence together in nature means that their separation in primary hydrometallurgical flowsheets is not only often necessary, but requires the use of innovative chemistry to achieve high selectivity. Today, increasingly stringent demands for the high-purity cobalt and nickel salts required for battery applications in consumer electronics, electric vehicles, and solar applications are again challenging the state of the art. The evolution of cobalt–nickel separations is traced from the basic precipitation technologies employed in 1960s, through commissioning of the first cobalt solvent-extraction plant in South Africa in 1974, to the commercialisation of organophosphinic-acid extractants (which provided a step-change improvement in selectivity) and their eventual widespread use in the 1980s and ’90s. This was followed later by their sulphur analogue, which enabled different possibilities for laterite processing in the new millennium. Separations in chloride media, which take advantage of the different speciation chemistries, and nickel extraction by oximes in ammoniacal systems are also discussed. More recently, chelating and solvent-impregnated resins have added further dimensions to the possibilities for flowsheet design and enabled higher purity products to be attained from both primary and secondary sources. Selected case studies and flowsheets are described.

By P Clark, P A. Kirsch, R Tapia Rivera

Community members’ sources of information about companies’ social investments are often influenced by the messages in a variety of communication channels, such as newspapers, television and social media. In this sea of communication channels, corporate communications may not always have the desired effect in influencing community perceptions. This paper explores the efficacy of communication between mining companies and communities in Chile through content analysis of corporate sustainability reports and newspaper reporting.Chilean media reporting between 2005 and 2013 is examined to identify community perceptions of corporate social investments made by mining companies. Content within the Chilean newspapers El Mercurio (national) and Soy Chile (regional) is contrasted with content from corporate sustainability reports published by The National Copper Corporation of Chile (Codelco) and Barrick Gold Corporation, Canada (Barrick) for the same period. The objective is to identify differences in the way that corporate social investments are reported by companies in sustainable development reporting and by media in newspapers.Overall, the study demonstrates that the media’s framing and reporting of corporate activities was more negative than positive. Moreover, media outlets tended to focus upon the ‘negative impacts’ or ‘damage’ to communities brought about by mining developments. Conversely, companies’ public communications were largely focused upon direct improvements in livelihoods (health, education, etc) of neighbouring communities. This preliminary study provides a baseline for the development of new formats of effective communication with neighbouring communities. The paper advocates for an increase in participatory mechanisms with affected parties, which could lead towards a greater mutual understanding of the impacts and draw parties closer together.CITATION:Tapia Rivera, R, Kirsch, P A and Clark, P, 2014. Challenging Perceptions? Sustainability Reporting, the Media and Mining, in Proceedings Life-of-Mine 2014 , pp 413–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By C. P. Manning

This paper reports recent progress in the development of a unique metal extraction technology utilizing zirconia-based inert anodes for the electrolytic reduction of metals from their oxides. In this process, the target metal oxide is dissolved in an ionically conducting liquid solvent phase. An extended anode consisting of an oxygen-ion-conducting stabilized zirconia membrane in intimate contact with a catalytically active electronic phase and an inert electronically conducting cathode are inserted into the molten flux containing the oxide. When the appropriate electric potential is applied between the electrodes the target metal is reduced at the cathode and oxygen ions are selectively transported across the stabilized zirconia membrane and oxidized at the anode. When the process is conducted at temperatures between 1200-1400°C, the ohmic resistance drop across the stabilized zirconia membrane is low, and high current densities on the order of I A/cm2 or greater can be obtained. In addition, the process efficiency can be increased further by directly reforming hydrocarbon fuel over the anode. Laboratory experiments at Boston University have demonstrated the technical viability of employing zirconia-based inert anodes for environmentally sound production of metals such as magnesium, tantalum, aluminum, etc., directly from their oxides. Significant progress has been made in the application of this concept to the electrolytic reduction of magnesium at 1300°C. The research topics covered include stability of the zirconia membrane in the selected molten solvent (flux), volatility of the flux, electrochemical characterization of the electrolytic cell, and analysis of the metals produced.

Jan 1, 2003

By Robert J. Timko

Because of leakage through and around permanent stoppings in underground mines, more air must be forced into a mine than would otherwise be required for ventilation. As power costs increase, costs resulting from air leakage add increasingly to the operating costs of mining. The Bureau of Mines evaluated four different stopping construction techniques based on the ideas that (1) airtightness could be enhanced by brushing rather than troweling on mortar sealant and that (2) modified mortars (mortars containing glass fibers and other additives for increased strength and adhesion) would improve sealing performance. Air leakage tests comparing conventional to modified stoppings were done when the stoppings were built, after 6 months, after 1 yr, and following simple maintenance. It was found that stoppings can be built and maintained better if-- The area where a stopping is to be built is properly prepared. Stoppings are constructed using the techniques devised by the Bureau. Stoppings are periodically examined for leaks. Stoppings found to be leaking, especially at the perimeters, are resealed.

Jan 1, 1983

By L. L. Chasko, D. W. Alexander

Researchers from the National Institute for Occupational Safety and Health’s Office of Mine Safety and Health Research conducted an assessment of the effects that ground control mesh might have on rock and float coal dust distribution in a coal mine. The increased use of mesh to control roof and rib spall introduces additional elevated surfaces on which rock or coal dust can collect. It is possible to increase the potential for dust explosion propagation if any float coal dust is not adequately inerted. In addition, the mesh may interfere with the collection of representative dust samples when using the pan-and-brush sampling method developed by the U.S. Bureau of Mines and used by the Mine Safety and Health Administration for band sampling. This study estimates the additional coal or rock dust that could accumulate on mesh and develops a means to collect representative dust samples from meshed entries.

Jan 1, 2014

By L. J. E. Hofer

THIS BULLETIN analyzes and summarizes research at the Bureau of Mines dealing with the preparation, properties, and reactions of iron carbides in the period 1948-60, part of which was sponsored by Wright Air Development Laboratories. The objective was to develop better catalysts for the synthesis of methane and higher hydrocarbons from hydrogen and carbon monoxide. The investigations resulted in the first adequate characterization of epsilon iron carbide, which later proved to be an important intermediate in the tempering of martensite in steel. At temperatures near 170° C, the carbon in carbon monoxide reacts nearly quantitatively with finely divided alpha iron to form an iron carbide in which the metal atoms occupy the positions of the close packed hexagonal arrangement with lattice parameters of ao=2.754 A and co=4.349 A. The carbide has a composition within 2 atomic percent of that required for the formula Fe2C, a Curie point of about 370° C, a specific magnetization of 160.4 ergs per gauss-gram Fe at 50° C, and a ferromagnetic moment of 1.70 Bohr magnetons. Epsilon iron carbide can be converted to chi iron carbide by thermal treatment at 343° C for about 70 hours. The chi iron carbide so formed has a Curie point of 247° C, a specific magnetization of 142.5 ergs per gauss-gram Fe at 50° C, a ferromagnetic moment of 1.72 Bohr magnetons per iron atom, and a paramagnetic moment of 5.5 Bohr rnagnetons per iron atom. Direct synthesis of this carbide from carbon monoxide at 240° C indicates a composition within 7 atomic percent of that required for Fe2C. Chi iron carbide can be converted to cementite at 550° C in about 315 minutes. The theta iron carbide so prepared has a Curie point of 210° C, a specific magnetization of 147.3 ergs per gauss gram Fe at 50° C, a ferromagnetic moment of 1.72 Bohr magnetons per iron atom, and a paramagnetic moment of 3.9 Bohr magnetons per iron atom. Pure chi iron carbide reacts to form theta iron carbide by the elimination of free carbon. In the presence of an excess of free iron in intimate contact with the carbide, chi iron carbide reacts with the free iron to form theta iron carbide. The second reaction proceeds at an appreciable rate at 320° C and can be used to snythesize finely divided theta iron carbide with no free-carbon impurity at low temperatures. The ease of the reaction in the presence of free iron suggests that chi iron carbide is an intermediate in the tempering of epsilon iron carbide to theta iron carbide as it proceeds in steels. Experiments on carbon steel show that the magnetic moment of the iron atoms in martensite is about 2.2 Bohr magnetons per atom, a value approximately the same as that of the iron atoms in alpha iron. The Curie points of epsilon iron carbide, chi iron carbide, and theta iron carbide were found -in various specimens of tempered steel to be 10° to 20° C lower than normal values. This shift is probably the result of manganese in solid solution. Preparations of various compositions of epsilon iron carbonitrides show many effects of extensive isomorphism between epsilon iron carbide and epsilon iron nitride. The action of carbon monoxide on finely divided alpha iron at 400° C results in free carbon deposits containing filaments about 0.1 micron in diameter and several times as long. The filaments are characterized by nuclei of dense material located midway from each end of the filament. Although carbiding to near completion at 240° C over periods of about 300 hours produces a preparation containing no appreciable percentage of epsilon iron carbide, very brief periods of carbiding of the order of a minute result in the formation of detectable epsilon iron carbide even at temperatures as high as 325° C. The data indicate that epsilon iron carbide is an intermediate in the formation of chi iron carbide during its formation from carbon monoxide in the gas phase. Attempts to convert cementite to chi iron carbide by cold work increased the Curie point but did not change the X-ray powder diffraction pattern.

Jan 1, 1966

By V. Ross

"Bench-scale flotation tests play a major role in the geometallurgical process value chain. Despite their apparent simplicity, these tests pose pitfalls in terms of operation, as well as the interpretation and modelling of results. In this paper we highlight key aspects to consider in generating accurate and reproducible experimental results, and critically review some assumptions relating to the estimation of entrainment and froth recovery. We subsequently focus on first-order equations to model kinetics and propose a method that accounts more realistically for the decay in kinetics over the duration of a float, and the contributions of froth stability and hence mass pull. The method was applied to three case studies on platinum group metal (PGM) ores and matched or outperformed first-order, two-component models. Also, it allows for a deeper analysis of the integrity of the bench-scale flotation results. IntroductionGeometallurgy is a structured, multidisciplinary approach that integrates key data from the geological, mining, mineralogical, and metallurgical aspects of the value chain to construct spatial models of an ore deposit such that the overall economic benefit and sustainability of an operation can be optimized. Process geometallurgy is aimed primarily at enhancing metallurgical efficiency and plant throughput by the application of appropriate mining and processing strategies, as well as supporting production planning and operational strategies to reduce the impact of highly variable ores. With flotation being the dominant concentrating process in the mineral value chain, the bench-scale flotation test is an important characterization tool – a relatively cheap, simple, and rapid way to obtain key information about the ore and its amenability to economic extraction of valuable minerals. This includes the evaluation of different ore types and the implications of mineralogical composition and texture for comminution and floatability, the effect of the grinding environment on the liberation of minerals, the electrochemical environment in the pulp (Bradshaw et al., 2006), the screening of reagents to improve floatability (Ekmekci et al., 2003), and the role of hydrodynamics in the recovery of valuables and the entrainment of gangue (Amini et al., 2016; Wang et al., 2016). It is also a critical tool in auditing the performance of a flotation plant by hot floats, paving the way for concept and feasibility studies and providing essential data on kinetics for the purposes of scale-up, optimization, and simulation of flotation circuits."

Mar 1, 2019

By Garforth W.

The chairman announced the new government duties of the out-going President, Sir Thomas Holland, and the formation of a new standing committee on mining to advise the Advisory Council for Scientific and Industrial Research on suitable projects for grants. Some of the potential lines for investigation into the best methods of winning and presenting coal in the best commercial condition include wasteful practices in operating steam boilers, national loss due to neglecting recovery of coal by-products, and the leaving of large areas of coal for fear of spontaneous combustion or as boundary pillars and support

Dec 1, 1916

By Stanley A. Feitler

This Bureau of Mines report deals principally with the resources and economic aspects of feldspar in the United States east of the Mississippi River. Although in a strict sense, all phases of the feldspar industry affect its economic structure, emphasis in this study is on supply, demand, and marketing. Although feldspar was originally mined for use in the manufacture of pottery and other ceramics, the glass industry, which began to use feldspar in the mid-1920's, now consumes more than half of the annual output. Most mining is open cut, and the methods used are similar to those used in mining crushed b stone. Excess plant capacity has been chronic, and production is usually about 30 percent of capacity fur the industry as a whole. Since 1947, feldspar consumption has grown more slowly than the average for all U.S. industry. This has fostered intense competition, especially for the glass market. Prices have not kept pace with inflation, and profits are small. The trend of consumption through 1970 for glass feldspar is expected to be upward; less rapid in consumption of ceramic feldspar is anticipated.

Jan 1, 1967

Fifty to 75 million years ago, hydrocarbon-bearing rocks were formed in the Green River formation of Colorado, Wyoming and Utah. The hydro- carbons can be extracted from these rocks, marl- stone but misnamed oil shale, after crushing and intense heating. At about 900°F the marlstone decomposes to produce liquid shale oil. A press release from the Colony Development Co. describes a process which may permit, for the first time, economically feasible access to shale oil. Shale oil has resisted economic extraction for almost three centuries. According to the USBM, a patent was issued as early as 1684 in England to produce "oyle from a kind of stone". France produced oil from marlstone in 1838 and a dozen years later, Scotland started an oil shale industry, producing kerosine, that lasted nearly 100 years. In both countries, the process involved crushing the stone and retorting it to decompose the kerogen-a long and costly process at that time. In 1859, Edwin L. Drake brought in the first oil well in Titusville, Pa., and shale oil faded into oblivion.

Jan 8, 1965

This report deals with the Schmalfeldt gasification plant for making synthesis gas, the Fischer-Tropsch plant, the hydrogenation plant and the catalyst factory, and includes a report on lubricating oil. THE SCHMALFELDT GASIFICATION PLANT The information was obtained on May 9 and 11, 1945, from Dr. Schneeberger (director), Dr. Schneider (director and power plant manager), Herr Dassau (manager of gas plant) and Herr Schultz (manager of Fischer-Tropsch plant). The plant was shut down as the result of very heavy air raid damage to other parts of the works

Jan 1, 1946

By Hanns J. Billmayer

This report, which covers the period from April 1975 to November 1975, describes the work performed in compliance with the requirements of Contract No. H0357091. The purpose of this contract was the development of protective canopy concepts applicable to rail haulage equipment used in underground coal mines.

Jan 1, 1976

By Schwartz M.

The current status of the heavy and light rare-earth elements outside China is reviewed. New suppliers of the light rare-earth elements are Lynas (Australia/Malaysia) and Molycorp (USA), which are anticipated to process 11 000 and up to 10 000 t/y, respectively, and the most advanced heavy rare-earth elements project is Avalon's Nechalacho project at Thor Lake, Northwest Territories, Canada. U3O8 Corp has potential rare-earth elements production, e.g. ytrrium and neodymium, from its Berlin deposit in Colombia and Namibia Rare Earth's Lofdal project (Area 4) has potential to produce an average of 1 500 t/y of separated rare-earth oxides. With regard to the three historical producers, India has some small-scale production, Brazil has been a small-volume producer and has potential for new heavy rare-earth elements production, while South Africa has no current production

Feb 1, 2015

By Forrest T. Moyer

To keep the mineral and allied industries informed of trends in the causes of accidents and to point out the need for corrective measures, the Bureau of Mines collects, analyzes, and periodically published health and safety statistics. This report includes data for 1964 on injury experience, with related employment statistics, at coal mines in the United States. These data are presented in tabular form under the following headings: General Injury Experience Tables 1 to 6: Current data on number of injuries, degree of injury, frequency and severity rates, average severity, and related employment and production data by work location.

Jan 1, 1967

By A. M. Cummings

Each mining district presents different problems as to the methods of ore extraction cad underground support, which are dependent upon the type of the ore deposit and the character of the inclosing rock. Mining costs, however, depend largely aeon the efficiency with which the methods employed underground are [applie] as well as upon the selection of the method best adapted to the physical conditions. The purpose of this paper is to present to the operator in other districts a detailed description of ho mining method used ins results obtained in tie exploitation of the bedded magnetite deposits of the Mineville district. The town of Mineville is situated in the Adirondacks, five miles west of Port Henry on Lake Champlain.

Jan 1, 1928