Search Documents

By Homer S. Frankhouser

Materials may be dredged, processed, stored and loaded for shipment at a single site in water depths ranging from 250 to 1200 ft. Solution mining may also be accomplished in deep sea situations. And, open air subsea mines with direct surface access may be developed and worked under the ocean floor. These concepts for deep sea mining are the results of extensive testing of individual components of the proposed systems by Dravo Ocean Structures, Inc., a subsidiary of Dravo Corp. A basic structure in these systems is the articulated platform. The platform consists of a gravity- type base and a buoyant cylindrical column which is constructed at an onshore location, towed to the offshore site and installed in a matter of days without use of heavy equipment. The base is also buoyant for towing purposes. This allows for gradual flooding to the point of negative buoyancy for positioning and anchoring to the ocean floor.

Jan 1, 1971

The philosophy of computer control of grinding and flotation at ZC/NBHC is presented. The performance and reliability of the in- stalled systems are discussed.

Jan 1, 1978

By Henry Faul

Measurement of radioactivity of rocks and ores has developed into a complete method of geophysical exploration. The problem falls into three natural categories: (1) surface radiation measurement in the field and underground; (2) radioactivity logging of drillholes; and (3) laboratory analysis of samples. Portable counters are used in the field for tracing radioactive formations and for quanti tative estimates of radioactive content of surface rock. Wartime advances in battery design make it possible to construct small precision counters that can be carried easily. Even the smallest conventional diamond drillholes can be logged, and actual content of the radioactive element can be measured. The exact grade of very thin active layers or veins can be estimated only approximately. Samples may be analyzed for their alpha, beta or gamma activity, and beta assaying is the best suited to rapid routine operation. Simple calibration with standard samples is sufficient for rough work, but a density correction is necessary when greater precision is required. Samples with high emanating power should be fixed and stored for three weeks to reestablish the radium-radon equilibrium prior to precision assaying. Carno-tite can be fixed by sintering or molding with plastics. Among the important new developments, a low-voltage Geiger tube has been 'designed recently, and crystal scintillation counters hold great promise for high-efficiency gamma-ray measurement. Introduction During the last few years we have witnessed an unprecedented rise in the demand for radioactive minerals, coming as a direct consequence of the discovery of nuclear fission and subsequent developments, the full impact of which is by no means in sight even now. It remains certain, however, that radioactive minerals, and especially those which can be used as ores of uranium and thorium, will continue to be of great interest not only to the prospector and mine operator but also to the various inspection parties envisioned by most of the schemes advanced for the control of nuclear energy on a world-wide basis. It is clear, therefore, that the measurement of radioactivity in rocks in the field as well as in samples in the laboratory has become a method of geophysical exploration of some importance. If we consider the recent technological advances in the general fields of nuclear physics and electronics it seems proper to review the present status of the methods and procedures of radiological exploration. General Considerations Equilibrium If we take a fixed amount of uranium that has just been purified, some of it will immediately start decaying into its first daughter element which in turn decays into its own daughter and so on down the line until the last daughter is reached—a stable isotope of lead. The rate at which a radioactive element decays is frequently expressed as the half-life, which is the length of time required for the decay of half the atoms in a given amount. The half-life is inversely proportional to the decay constanl X which is defined as the number of atoms which decay in one unit of time divided by

Jan 1, 1949

By Henry Faul

Measurement of radioactivity of rocks and ores has developed into a complete method of geophysical exploration. The problem falls into three natural categories: (1) surface radiation measurement in the field and underground; (2) radioactivity logging of drillholes; and (3) laboratory analysis of samples. Portable counters are used in the field for tracing radioactive formations and for quanti tative estimates of radioactive content of surface rock. Wartime advances in battery design make it possible to construct small precision counters that can be carried easily. Even the smallest conventional diamond drillholes can be logged, and actual content of the radioactive element can be measured. The exact grade of very thin active layers or veins can be estimated only approximately. Samples may be analyzed for their alpha, beta or gamma activity, and beta assaying is the best suited to rapid routine operation. Simple calibration with standard samples is sufficient for rough work, but a density correction is necessary when greater precision is required. Samples with high emanating power should be fixed and stored for three weeks to reestablish the radium-radon equilibrium prior to precision assaying. Carno-tite can be fixed by sintering or molding with plastics. Among the important new developments, a low-voltage Geiger tube has been 'designed recently, and crystal scintillation counters hold great promise for high-efficiency gamma-ray measurement. Introduction During the last few years we have witnessed an unprecedented rise in the demand for radioactive minerals, coming as a direct consequence of the discovery of nuclear fission and subsequent developments, the full impact of which is by no means in sight even now. It remains certain, however, that radioactive minerals, and especially those which can be used as ores of uranium and thorium, will continue to be of great interest not only to the prospector and mine operator but also to the various inspection parties envisioned by most of the schemes advanced for the control of nuclear energy on a world-wide basis. It is clear, therefore, that the measurement of radioactivity in rocks in the field as well as in samples in the laboratory has become a method of geophysical exploration of some importance. If we consider the recent technological advances in the general fields of nuclear physics and electronics it seems proper to review the present status of the methods and procedures of radiological exploration. General Considerations Equilibrium If we take a fixed amount of uranium that has just been purified, some of it will immediately start decaying into its first daughter element which in turn decays into its own daughter and so on down the line until the last daughter is reached—a stable isotope of lead. The rate at which a radioactive element decays is frequently expressed as the half-life, which is the length of time required for the decay of half the atoms in a given amount. The half-life is inversely proportional to the decay constanl X which is defined as the number of atoms which decay in one unit of time divided by

Jan 1, 1949

By M. K. Foster

Ten horizontal retort zinc blocks of a modified Hegeler design are in operation at Nueva Rosita, Coahuila, Mexico, and produce approximately 170 t of spelter daily, or 62 000 t/year. A block consists of two furnaces of 448 retorts each, making 8960 retorts as the plant complement. Each furnace block is fired with natural gas and air maintaining the combustion mixture in the furnace always slightly reducing. No attempt to recover energy through waste heat boilers is made. The spelter moves to market by rail and truck either in palletized bundles weighing approximately 1060 kg, as loose slabs weighing 26.5 kg each, or as 1088 kg ingots. At present 46% of the metal is exported and 54% is consumed domestically in Mexico. The present day trend toward equalized or alloyed spelter, as well as special shaped castings results in sales of 35% of the entire plant's production. Sulfuric acid is also produced by the Contact Process using vanadium pentoxide as the catalyst. The plant is basically a Monsanto contact system, producing approximately 68 t of 100% sulfuric acid daily. Both 98.5% sulfuric acid and 20% oleum are available. All of the acid made is consumed in Mexico. Shipments are made in 26,900 dm3 tank cars.

Jan 1, 1970

By Thomas J. Peters

The Goat Rocks RARE II further planning areas contain no known mineral resources and have very low mineral potentials. County mining records show only one mining claim area; however, no mineralized material was found at the described location. Andesite suitable for building stone may be present, but similar material can be quarried more economically elsewhere. Several anthracite coal prospects are near the area, but the likelihood of finding an economic deposit of coal or other fuel is very low.

Jan 1, 1981

By V. M. Paretsky

The basic work conducted by Prof. A.Yazawa has demonstrated that in order to ensure single-stage white metal production by autogenous smelting of copper sulfide raw materials, it is most favorable to use highly basic slags, in particular oxide systems CaO-FeO-Fe2O3-Sio2. he special studies have been conducted in the Gintsvetmet Institute to investigate the composition and structure of slags produced on a semi-commercial scale when testing the KFP and FBP processes for white metal smelting, as well as the slag obtained in a full-scale KFP furnace at the Almalyk copper smelter. The investigations conducted have demonstrated why production of high-grade matte or white metal is associated with lower loss of copper in slag in a series: silicate slag I silicate-calcium slag I ferrite-calcium slag.

Jan 1, 2003

By Raymond Franz

Of the many types of capital equipment found in a surface operation, draglines and mining shovels are probably subjected to the most severe service. Yet, some excavators have seen a generation or more of continuous service-proof, if any is needed, of their ruggedness. To keep these expensive pieces of machinery operating, a continuing maintenance program which includes field weld repairs is essential. During an excavator's working life, minor cracks may appear in parts of the steel structure, caused by fatigue and sometimes material defects-defects so small they could not be detected during manufacture.

Jan 6, 1978

By Leonardo Semedo de Mattos Siqueira, Renata Ferreira Muller

The Granulometric Ratio (RG) is one of the most important indicators related to the pelletizing product. Through it, it guarantees good permeability of the bed of pellets, optimization of the thermal cycle and, thus, better results of physical quality and consumption of the energy matrix. To guarantee this indicator, it is necessary that the processes of agglomeration of pellets, classification of raw pellets and screening of burned pellets are under control of certain parameters and with a level of stability assured.

Oct 1, 2019

By Vito J. Colangelo

The primary object of this study was to determine the effect of ferrite and its orientation upon the mechanical properties of a precipitation -hardening stainless steel with particular attention to the short-transverse properties. The investigation consisted of Jour major parts : the preliminary investigation of billet properties, the effect of forging reduction and ferrite content upon mechanical properties, the effect of notch orientation upon impact strength, and the relationship of heat composition to ferrite content. Low ductility and impact strength in the short transverse direction were found to he associated with the orientation and shape of- the ferrite plates. It was also determined that impact strength varied with notch orientation. The test values obtained with the notch perpendicular to the plane of the ferrite plate were lower than those obtained in the notch-parallel condition. The over-all investigation showed that high ferrite contents in general had a deleterious effect upon mechanical properties and that the ferrite content could he minimized by exercising rigorous control of the heat composition. A careful balance of elements, nitrogen in particular, must he maintained in order to reduce the formation of ferrite. THE precipitation-hardening stainless steels were developed to fulfill a need for high-strength corrosion-resistant alloys. In the annealed condition they are soft and ductile and possess many of the desirable characteristics of the austenitic stainless steels. In the hardened condition, the alloys exhibit the high strength and hardness of the martensitic stainless steels. The alloy under consideration in this investigation has a nominal composition as follows: C Mn Si Cr Ni Mo N 0.13 0.95 0.25 15.50 4.30 2.75 0.10 The hardening mechanism is identical to that of other hardenable steels in that it depends upon the transformation of austenite to martensite. This alloy because of its annealed structure and its ability to be hardened combines the desirable forming and corrosion properties of the austenitic grades with the high hardness and strength levels attainable with the hardenable grades. The reason for this apparent duplicity of proper- ties can be explained by considering a basic metallurgical difference between the hardenable stainless steels and those of the austenitic group. Both types are austenitic at 1800°F but, while the martensitic grades transform to martensite upon rapid cooling to room temperature, the austenitic grades remain austenitic even when cooled to temperatures below room temperature. The major difference then is in the degree of austenite stability. This stability can quantitatively be described by the Ms temperature. The Ms is defined as that temperature at which austenite begins to transform to martensite. The austenitic grades for example may be cooled to -300°F without producing significant quantities of martensite. The hardenable stainless steels on the other hand have an Ms temperature in the vicinity of 400" to 700°F. In cooling to room temperature, these alloys traverse the entire Ms-Mf range and show almost complete transformation to martensite. The semiaustenitic stainless steel, however, occupies an intermediate position with respect to its austenite stability. The analysis is so balanced that the Ills temperature lies at or slightly above room temperature. The resulting alloy retains much of its austenite at room temperature and yet responds to hardening heat treatments. Achieving this delicate balance of elements is therefore of great importance. Slight imbalances of the equivalent Cr-Ni ratios frequently result in the presence of 6 ferrite. It is the effects of this ferrit with which we are concerned, more specifically the effect of the quantity and ferrite orientation upon mechanical properties, particularly ductility. PROCEDURE A) Preliminary Investigation of Billet and Forging Properties. In order to determine the effect of ferrite on billet properties, billet stock from three heats with various ferrite contents was utilized. Tensile specimens were obtained in the transverse and longitudinal directions from this material and heat-treated as shown in Tables I and 11. Forgings were made from these same heats, the purpose being to determine what effect, if any, the ferrite might have upon the mechanical properties. These forgings were made in such a manner as to elongate the ferrite in the longitudinal and transverse directions. The method of forging was as follows. A section was cut from a 6-in.-sq billet of Heat A and flat-forged to 1-1/2 in. thick. Working was done from one direction only with no edging passes as shown

Jan 1, 1965

By N. D. L. Burger

Underwind and overwind protection system concepts for mine hoist shafts were developed in conjunction with and for the Safety in Mines Research Advisory Committee (SIMRAC). End-of-wind operation of mine hoists is the most hazardous aspect of mine hoisting, carrying the highest risk of loss of life, injuries to workers and loss of production. Systems operating mechanically and with local actuation were developed. This was done in order to remove the increased risk associated with dependency on remote or external energy and information supply associated with most existing protection systems. The proposed underwind protection system concept absorbs the energy of motion of a conveyance overrunning the design lower limit of travel by drawing a metal strip through a set of rollers. This action causes dynamic cyclic plastic bending of the strip material that converts the kinetic and potential energy of the conveyance into strain energy of the metal. In the concept design a pair of steel wire rope slings attached to the strips catch the overrunning conveyance and transfer the retardation force. The proposed overwind protection system concept absorbs the energy of motion of a conveyance overrunning the design upper limit of travel by early detaching of the conveyance from the hoist rope. This detaching is carried out via an additional detaching hook activation mechanism fitted at a sufficient height below the spectacle plate to allow the conveyance to retard to standstill under gravity before it would crash into the spectacle plate. The conveyance so brought to rest is prevented from falling by means of jack catches on the conveyance interacting with a rack (toothed profile) fitted on the guide rails in the retardation zone. Scale models (1:10 scale) of both protection systems were designed to conform to established retardation standards. The retardation standards were limited by the requirement of passenger safety in retarding cages. The models were then built and tested in a1:10 scale shaft model. Retardation performance close to the required levels was achieved. The retardation distance required should allow such systems to be retrofitted in most existing shafts. Given the simplicity and robustness of the designs, further development was recommended because of their enhanced self-sufficiency and reduced risk of malfunction. Keywords: underwind, overwind, deceleration, mineshafts, hoisting.

Jan 1, 2004

The æMountain Camp reefÆ at Alford's mine, Wakamarina,Marlborough, had no recorded gold production although assays of 5 - 26 g/t were reported, but it did produce c. l000 kg of scheelite. The lode consists of a lower massive quartz layer, and upper, cm-banded, ribboned quartz layers, and has a very low sulphide content. Within the massive layer, relict early fine-grained mosaic quartz with idioblastic scheelite is surrounded by recrystallised granoblastic coarse-grained quartz with calcite and plagioclase, in which an original ribbon banding texture is mimiced by strings of tiny inclusions. In both the banded and massive layers, rounded quartz grains, created by cataclastic milling of grain margins and along syn-vein fractures, have been partially annealed within later quartz overgrowths. Late fibrous quartz and calcite fill brittle cross fractures.   Deformation events D1 and D2 are associated with mid-late Jurassic metamorphism of the Pelorus Group, D2 producing the main regional schistosity (S2, and the earliest scheelite. D3 is an extensional mylonitic shear event that formed the dominant schistosity in Alford's mine (S3). The quartz lode was emplaced within the mylonite by a series of individual dilation pulses (D4). The D5 event caused crenulation of the S3 mylonite, kink banding and chevron folding of the S2 schist and S3 mylonite, and reverse faulting, rodding and cross-fracturing with late fibrous quartz-calcite veining of the D4 quartz lode.   Fluid influxes during successive dilations of D4 fractures progressively caused recrystallisation of earlier quartz bands on the footwall, annealing and recrystallisation of quartz along milled crystal margins and fractures, and deposition of minor sulphides. There was thus a dynamic interplay between fault dilation, lode fracture, fluid influx, lode band deposition, and lode recrystallisation. Illite-Kfeldspar al ¦ 2 Ma (K/Ar), c.30 Ma after metamorphism.

Jan 1, 1996

"THE PACIFIC CONTINENTAL MARGIN OF CANADA is de-fined, for the purposes of this paper, as the area sea-ward from the present mainland coast of British Columbia to the foot of the continental slope. It thus coincides with A. Sutherland Brown's Insular Tectonic Belt. The region is limited to the north and south by the political boundary with the U.S.A., the location of which is still in dispute.The region can be subdivided into: (1) an interior trough comprising the Queen Char-lotte, Comox and Nanaimo basins; (2) a medial uplift comprising Vancouver Island and the Queen Charlotte Islands; and (3) a marginal shelf which is extremely narrow (Jess than 5 km) west of the Queen Charlotte Islands, widens to 160 km in Queen Charlotte Sound and is about 35 km wide west of Vancouver Island, where it is underlain by the Tofino sedimentary basin, with its• extension, the Juan de Fuca Basin, at the southern end.The medial uplift consists of a highly disturbed anticlinorium of mainly Mesozoic rocks, with a core of Palaeozoic. The rocks include thick sequences of eugeosynclinal volcanics and sediments. There is strati-graphical evidence of repeated interruption in sedi-mentation. By late Jurassic, the main eugeosynclinal phase was over and a successor basin was initiated in the interior' trough. This became filled, during Cre-taceous and Tertiary time, with sediments ranging in environment from bathyal turbidites to terrestrial conglomerates and coals. West of the medial uplift, another successor basin developed in early Tertiary times and became filled with mainly deep-water marine sediments. A third effusive sequence marks the base of the Tertiary on Graham Island and over most of the Hecate Strait region and Tofino Basin."

Jan 1, 1970

By Anjan Kumari, B. K. Soni, Manis Kumar Jha, A. Vidyadhar, Vinod Kumar

"In the present paper, recovery of valuable metals from the poly-cracked ash obtained by pyrolysis of discarded PCBs has been studied following physical beneficiation and a hydrometallurgical process alternate to smelting. The ash is subjected to comminution for the separation of metallic components from non-metallic fractions by scrubbing, tabling and froth flotation which enriched the metal in the concentrate -97% which was further screened to separate high and low metal concentrate. The finer fraction containing -12% metallic value was leached in acidic solution. Almost all (Cu, Pb, Fe, etc) were leached in 4M HN03 at 90°C in 75 min at a pulp density 100 g/L. The characterization of both ash and residues were made by XRD, EPMA, EDS, etc. to validate the experimental results. The metals from the leach liquor could be recovered/separated using solvent extraction techniques which can further be processed to get pure metal salts/ sheets.IntroductionPrinted circuit boards (PCBs) are an essential component of electrical and electronic equipments (EEEs) as it plays an important role during operation of these devices. The world market of PCBs has reached nearly $60 billion in 2012, with 1.7 percent real growth over 2011 [1]. The diverse technology-driven global market is expected to grow at an average annual rate of 5% by 2014 [2]. The waste EEEs are generated due to replacement of obsolete equipments with modem ones and thus their demand is also increasing rapidly [3]. The discarded e-wastes are being piled up as landfills which affect the environment and cause health threats to living organisms, if not disposed of properly. These e-wastes contain metals some of which are precious, few are hazardous and others as valuable."

Jan 1, 2014

By C. A. Herbert

"Haulage accidents usually are responsible for about 17 or 18 percent of all coal-mine fatalities and about 21 percent of all non-fatal coal-mine accidents. When the relatively small number of employees continuously exposed to haulage hazards is considered, it would appear that haulage is more hazardous than any other phase of coal-mine operation.Haulage accidents have increased from year to year, doubtless due to the increase in electrical haulage, and particularly to the use of larger cars, heavier locomotives, longer hauls, and greater speed. Unless very definite steps are taken to eliminate the causes of these accidents, they will continue to increase rather than be reduced, as they can and should be.Underground haulage in many of the large modern mines of today is similar in many respects to railroad practice. In recent years the railroads have made wonderful strides in reducing accidents, and instead. of being one of the most hazardous occupations, as it once was, railroading is now one of the safest. Doubtless, if thought and action, similar to that given to reducing accidents among railroad passengers and employees, were given to safety in mine haulage, under¬ground haulage accidents could be reduced in about the same ratio.Haulage accidents may be classified, according to responsibility, into two groups - those for which management is largely responsible and those for which the employee is largely to blame; there is, however, an overlapping of responsibility from one group to the other. If, therefore, haulage accidents are to be reduced, it is absolutely essential that both management and employees cooperate to this end.In the first group, for which management is largely responsible, may be included accidents due to faulty equipment, moor track, a poorly arranged system of haulage, lack of clearance or of overhead protection, and dirty roadways; even in these features, however, the employee is not without a measure of responsibility, as failure of haulage equipment possibly may be due to lack of care on his part, failure to report when equipment is out of order, or failure to do a good workmanlike job of installing or repairing or operating.To the second group of accidents for which the employee may be largely responsible, belong those caused by such careless practices as jumping on and off fast-moving trips, coupling on the ""fly"", running at excessive speeds, failure to properly block cars, and similar hazardous and unnecessary acts of omission or commission. If, however, management condones such practices, or, as in some instances, insists upon them, it must accept its share of responsibility for the accidents that inevitably result.Some of the most prolific sources of haulage accidents will be discussed briefly, together with the steps that may be taken to minimize their occurrence."

Oct 1, 1939

By Frederick G. Coqueron, Joseph E. Pogue

The purpose of this study is to present the results of a detailed survey of the financial and operating aspects of 30 oil companies comprising a major sample of the American petroleum industry. This review supplements a previous paper entitled "Capital Flow and Capital Formation in the Petroleum Industry, 1934-1941,"a and deals not only with a longer period but also gives new and more revealing analyses of the capital movements and characteristics. The data are gathered from published financial statements of the companies, especially the annual reports to stockholders and Form 10-K to the Securities and Exchange Commission, supplemented by confidential information. The 30 oil companies covered by this study are listed on the leading stock exchanges and for the purpose of analysis are grouped as follows: 9 companiesb engaged principally in crude production, 4 companiesc with production averaging in excess of refinery requirements, and 17 companiesd with refinery throughput in excess of crude production. These samples are sufficiently broad and representative to constitute norms against which individual company performances may be profitably compared. The 30 companies in 1942 produced 54 per cent of the Nation's total output of crude oil and refined 79 per cent of the country's crude run to stills. The financial data apply predominantly to the domestic oil business, although 15 of the companies have investments and operate facilities in foreign countries. The net value of these foreign holdings amounted to 724 million dollars, or 12 per cent, of the combined net assets of the 30 oil companies at December 31, 1942.

Jan 1, 1944

By Michael Perch, Charles C. Russell

Nearly 95 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69,9, and in 1938 it was 61.3, To produce a net ton of pig iron 1959 lb. of coke was required in ,1940 and 1760o lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank1 standardized by the American Society for Testing Materials. Although this method of classification has been an American standard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1942

By J. Manrique, B. Bustamante, P. Altamirano, J. Mendoza, J. Reyes

With no doubt, Peruvian mining potential is great as well as the energetic one. Unfortunately, this potential is threatened by social unrest. Several methods and strategies from different standpoints have been rehearsed with respect to unrest in Peru, however, the problem goes on without getting the right conflict interpretation and most of all, effective solutions are not achieved. The mining unrest dates from ancient times and has not always had the same stages nor the same demands. In the 20´s and 30´s, conflicts focused on workers’ rights and demands. In the 70´s, conflict focused on mines nationalization that were under foreign control. In the 80´s, conflicts took place because of requesting better wages, better working conditions, better mining profits distribution and more investment in communities that surround mining projects. It is very important to highlight those transversal demands such as land purchase, agricultural property, impacts and water reduction as well as pollution, impact on water systems and disappearance of springs have always been present over the historical period.

Mar 2, 2022

By J. Mizera, J. Zdunek, K. J. Kurzydlowski, A. Dobkowska

This work concerns comparison of corrosion resistance of the aircraft aluminum alloy composed of Al - 2.3%Li - 0.1% Zr. The alloy was hot rolled (HR) from 13 mm to a thickness of 4 mm (e = 2.4) and 1 mm (e = 5.2). Corrosion resistance was investigated by Potentiodynamic Polarization Test. The investigation relied on exposure samples in two different corroding medium: 0.5 M NaCl solution and 0.01 M Na2SO4 solution with added 0.01% of Cl- at room temperature. Furthermore, the microstructure was analyzed using the optical microscope with polarized beam. The hardness was measured on lengthwise profile. It was stated that alloy after the largest deformation (equivalent total strain e = 5.2) is characterized by the best mechanical properties and the best corrosion resistance. The alloys in initial state and after deformation to 4 mm (e = 2.4) are characterized by worse corrosion resistance. It is associated with microstructure and density of dislocation in analyzing material.

Jan 1, 2015

By S. G. Kumar, R. G. Reddy

"Niobium aluminides offer the advantage of higher high temperature capability compared to other intermetallic aluminides due to the refractory nature of niobium. However, the reaction sequence in Nb-Al system is sluggish and currently there is a great interest in the processing aspects of these materials. In the present study, a systematic investigation was undertaken to compare the effect of different powder metallurgy processing routes on the phase relations and microstructure of 66Nb-22AH2Ti (in atom percent) alloy. The three different process routes adopted were: (i) cold pressing followed by reaction sintering; (ii) cold pressing and hot pressing followed by sintering; and (iii) arc melting, hydride-dehydride process to make the alloy powder followed by cold pressing and then sintering. The samples are analyzed by XRD, Optical Microscopy, SEM-EDS and EPMA. The analysis showed that alloy pellets made from pre-alloyed powders i.e., arc melting followed by hydride-dehydride process, gave good densification and more Nb3Al formation.1. IntroductionTo improve the performance standards of turbine engines, materials scientists are challenged to develop materials that have· high thrust-to-weight ratio with high specific strength, high specific modulus and good environmental properties at elevated temperatures. The conventional high temperature materials like nickel based superalloys are high in density and hence many of the high temperature materials scientists have focussed their attention on intermetallic aluminides like Fe-AI, Nb-AI, Ni-AI and Ti-AI in recent years. The phase relations and properties of alloys based on Fe-AI, Ni-AI and Ti-AI are fairly well known whereas little is known about the alloys based on niobium aluminides."

Jan 1, 1996