Search Documents

By David Forrester

Subsidence beneath the land surface has traditionally been monitored using the most accurate surveying methods of the day. Over the several hundred years of subsidence investigation, these techniques have improved, and thus the accuracy of subsidence measurements has improved. In circumstances where the subsiding surface is masked by water or rock, novel methods must be developed. This method describes the recent successes of subsidence monitoring using advanced bathymeric techniques in the Sydney Coalfield. In order to obtain subsidence profiles above submarine coal extractions, seafloor bathymetry surveys, run before and after mining, have shown that subsidence profiles can be detected, despite the primitive nature of some of the trials. Very recently, there have been considerable advances in this field, associated with the availablity of high-powered personal computers to control data collection and analyse the results. The recent surveys described in this paper have demonstrated the considerable potential for such methods. This paper describes bathymetric subsidence monitoring developed in the Sydney Coalfield, illustrated with some typical results, and summarizes the findings of the research leading to the development of subsidence design criteria specific to the Sydney Coalfield.

Jan 1, 1996

By Brandon Axelrod

This paper follows a student’s interest in explosives which began at an early age after watching a television program highlighting explosives engineering. The use of explosives in those programs led to curiosity about how one gets involved in the industry. These programs enticed the author to further investigate the explosives industry leading him to an explosives camp for high school students. After attending the camp, this passion further developed into postsecondary education.

Jan 1, 2015

By J. H. Brophy, A. L. Prill, H. W. Hayden

An error lzas been found in the conventional way of determining the time exponent of linear shrinkage for the solution-precipitation stage of liquid-phase sintering. Large amounts of shrinkage due to initial rearrangenzent result in erroneously low exponents and tni si dentification of the rate-controlling process. Two alternative, mathematically correct, methods of calculation are applied to existing data on Fe-Cu, WC-Co, and Tic-Ni-Mo. This results in reidentifi-cation of the rate-controlling process and somewhat better agreement with related data. In each case the solution-precipitation process is solution-controlled and not diffusion-controlled. THE liquid-phase sintering process has been the object of a considerable amount of research for many years. Linear shrinkage vs time data at various sintering temperatures have been used recently in an attempt to identify the prevailing mass-transport processes in a number of metallic and nonmetallic systems. There is an analytical error inherent in the methods previously used for handling data during the "solution-precipitation" stage of shrinkage which must be recognized before the correct rate-controlling processes can be determined. It is the purpose of this paper to show how the error has affected previous conclusions and to suggest corrections. A number of mechanisms have been proposed to explain experimental observations during sintering in the presence of a liquid phase. The earliest of these is due to Price, Smithells, and williamsl who attributed the observed growth of the solid phase to the simultaneous solution of smaller particles and growth of larger particles. From the work of Lenel et al.2,3 and Gurland and Norton4 has come the suggestion that the liquid-phase sintering process may be divided for analysis into three steps: 1) rearrangement upon formation of the liquid phase; 2) solution and reprecipitation of the solid phase in the liquid; and 3) "coalescence" or a final stage of sintering, characteristically slower than the solution-precipitation process. The sequence of steps is shown schematically in Fig. 1. Kingery5 presented a thermodynamic and kinetic analysis of the first two "stages" of the liquid-phase sintering process in which the functional dependence of lineal shrink- age on time at temperature was used to identify the rate-controlling mass-transport process. Table I summarizes the time dependences and processes considered by Kingery.5 This method of data presentation has been employed by Kingery and coworkers for Fe-CU,6 WC-Co, and a number of nonmetallic systems," and bv Whalen and Humenik for Tic-Ni-Mo and Fe-cu.8 In each of these studies, the rate-controlling step during the "solution-precipitation" stage was identified from the slope of the curve in that stage on a logarithmic plot such as Fig. 1. However, in all of the previous studies, at a certain composition, relatively large amounts of shrinkage due to rearrangement preceded the solution-precipitation stage. Under these conditions, the larger the amount of rearrangement shrinkage the

Jan 1, 1965

By Mark Kuchta

A new database application for long term production scheduling has been developed for LKAB's Kiruna mine. The scheduler uses a new block data structure whereby the monthly production data for three raw ore products are predetermined on a month-by-month basis for each production area that could be mined within the schedule time horizon. The production schedule is created by assigning the starting dates to the each production area subject to various mining operational constraints such that that the monthly deviations for the production targets are minimized. The system is well integrated into the mine's overall computerized mine planning system.

Jan 1, 2002

By James W. Wade

THIS discussion of the future supply of lead refers only to the next ten-year period. Beyond that no prediction can be made that would be of sufficient accuracy to serve any purpose. When any commodity is by an unsatisfied demand forced to a higher price level, and the profits of those who are able to produce the commodity are greatly increased, there is awakened a new interest in the commodity on the part of both producer and consumer. The consumer attempts to reduce his costs by developing substitutes or assisting in the development of new sources of supply. Lead is now going through this stage. The lead producer is increasing development expenditure and searching for new mines. The consumer is developing substitutes as illustrated by the increasing use of zinc oxide as a pigment, and the use of dry batteries in radio sets. The search of the Ford interests for lead, by prospecting in Missouri and Idaho, is induced by the effort to develop a new source of supply. Considering the index figures of the Department of' Commerce, it is evident that lead is on a substantially higher price level. For February, 1926, the index figure of lead is 209, while the general commodity price index is only 156, 100 being taken as the base for 1913.

Jan 1, 1926

By W. C. PAGE

HARVEY S. MUDD has the unusual distinction of having virtually inherited a Directorship in the -A.I.M.E., for he was appointed to the Board to fill the unexpired term of his father in 1926. Since then he has served as a Director continuously until 1936, and now he is a candidate for Vice-President. One of the first words that young Harvey tried to say was "ore," for he was born in Leadville, Colorado, in the heyday of that camp, where Seeley W. Mudd for years ran the Small Hopes mine. Stanford and Columbia gave him his mining education, and the Shattuck-Arizona, at Bisbee, his first job. Afterwards he examined many

Jan 1, 1937

By George C. Bateman

WE in Canada want to see industry get back to a normal economic basis as soon as possible but wartime controls cannot be dispensed with immediately the war is over. Perhaps never again will we be entirely free from some of the types of controls such as those set up during the war. Certainly the taking over and disposal of surplus materials contemplates the continuation of some form of control for many years to come. However, to the extent that it is possible, the Allied nations are exponents of free enterprise.

Jan 1, 1944

It has been thought in the past that New Zealand had ample coal reserves, able to provide fossil fuel supplies well into the future. Such is not the case and every effort must be made to achieve the highest possible extraction rate in all new coal mining ventures. While the relative cost and availability of completion or fuels has been largely responsible for the slow growth of coal production in the past, a world shortage of fuels has given coal a new importance and required better utilisation of coal reserves. New mining ventures in thick-seam coal deposits cannot be planned and designed without geotechnical investigations designed to provide information required by the mining engineer and analyst. Finite element analysis of mine workings may provide essential information on the optimisation of mining techniques and the design of underground support and roadway shapes.

Jan 1, 1976

By Pavel Vasak

The Laurentian University Virtual Reality Laboratory (VRL) has provided a unique platform for the development and testing of novel seismic and microseismic data processing and visualization technology. In collaboration with Vale?s Creighton Mine, the technology was implemented at the mine site and consists of a VRL system and site calibrated Seismic Excavation Hazard Map (SEHM) software. The SEHM was developed as a practical solution for the mine operator to identify areas of elevated, active rock mass damage processes caused by recent mining activity. This paper is a pictorial representation of the 3D stereoscopic demonstration of the Creighton Mine seismic data distribution and interpreted SEHM for the first quarter of 2009. A live demonstration is scheduled at the Laurentian University VRL as one of the conference field trips. The demonstration highlights the technology transfer of research concepts into a near-real-time excavation hazard system that utilizes the key aspects of virtual reality technology; the ability to integrate large datasets (geology, mine excavation, (seismic) monitoring data, production scheduling, stress model, etc.); the ability to manipulate and visualize large datasets in both space and in time (mining sequence); and the ability to review the datasets by a group of experts in an immersive (3D stereoscopic), collaborative environment to better understand the processes and context of the mining-induced seismicity and evaluate potential risks to the mining operation.

Oct 1, 2010

By Cyril Stanley Smith

THE art of metallography is mature and the forms in which various micro-constituents appear are well known. Investigations almost without end have disclosed the importance of the exact manner of distribution of phases on the physical properties and usefulness of an alloy. Surprisingly, however, relatively little attention has been paid to the forces that are responsible for the particular and varied spatial arrangements of grains and phases that are observed. Like the anatomist, the metallurgist has been more concerned with form and function than with origins. In this paper it is proposed to develop the simple concept that many microstructures result from an attempted approach to equilibrium between phase and grain interfaces whose surface tensions geometrically balance each other at the points and along the lines where they meet. From this follows a number of principles which may prove to be of interest to the metallographer and of practical use in explaining failures and in designing alloys for particular service. In general, the discussion will be limited to structures obtained after full annealing. The simple principles do not apply to structures resulting from Widmanstatten mechanisms in precipitation, or to other structures not in local equilibrium and in which lattice coherency is a determining factor. INTERFACIAL TENSION Much has been written by physical chemists about the free energy of surfaces, which manifests itself as a measurable surface tension. Two- and three-phase interfaces in fluids seek a condition of minimum energy and approach a geometrical configuration in which the various forces are in vectorial balance.* Measurement of the angles established between the interfaces when in equilibrium provides a quantitative value for the relative value of the surface forces involved. The case of two fluids meeting at the surface of a solid (of great importance in connection with the flotation of minerals) has often been studied, but there have been few investigations of the equally definite interface between two or more crystals of a single solid phase, or the more complex cases where crystal grains of more than one phase are involved. The principles are best illustrated by considering first the case of two and three immiscible liquids. If, as in Fig I, a liquid, 2, is dropped into a less dense liquid, I, it will form a sphere-if gravity and viscosity can be ignored-for in this shape the interface has the smallest possible area. If these two phases should together encounter a third phase in which they are both immiscible, the geometry will change to become that which gives the lowest total energy for all three interfaces. Thus, if the spherical drop of liquid, falling through r, eventually reaches the interface between liquids 3 and I (we are assuming that the density of 3 is greater than 2, and 2 than I), it will assume the shape of a lens, the angle

Jan 1, 1948

By Edwin F. Shorey, Richard F. Coon, Steven B. Fradkin

Crosstown Interceptor Phase IA is the first deep tunnel element of the Milwaukee Inline Project. The tunnel contract includes 6,492 meters (m) of 9.1-m-diameter tunnel, two access shafts, and partial lining for structural purposes. The work also includes grouting to be performed as directed by the engineer to provide groundwater infiltration control in lined and unlined reaches of the tunnel. This paper summarizes infiltration observations, progress of the grouting work, and its potential application to the remainder of the Milwaukee project.

Jan 1, 1987

By H A. Myburgh

The beneficiation of heavy metal oxides, such as iron ore, is usually performed with heavy medium separation in cyclones, static baths and lately with Larcodems. Atomized ferrosilicon is most suitable as a heavy medium at densities above 3600 kg/m3 whereas a mixture of milled and atomized ferrosilicon is suitable at densities below 3600 kg/m3. When operating a beneficiation plant at densities higher than 3600 kg/m3 the quality of the ferrosilicon particles is an important factor that influences the control of the beneficiation process. Therefore, it is important to know how the rheology would be affected by the ferrosilicon quality as it also influences the control of the process at these elevated densities. Background The Kumba Resources Sishen Iron Ore Mine in South Africa produces 26.5 Mt iron ore per annum from its beneficiation plant. The ore body consists mainly of laminated and massive type hematite ore that is crushed down to ?90mm before being beneficiated by means of a combination of Wemco drums, Larcodem and dense medium cyclone separators. The need for higher densities When the percentage of high-density gangue2 is higher than normal in the run-of-mine (ROM), a higher separation density is necessary to produce a product to specification. Certain ore types of this quality in the Sishen reserves require a separating density higher than 4000 kg/m3, whereas densities would normally average 3600 kg/m3 when beneficiating ores of normal high-density gangue content. Sink and float tests conducted on the ROM material at Sishen revealed some interesting characteristics. In the waste fraction, (density < 3600 kg/m3) it was found that the %Fe was <21% (Fig. 1). Similarly, for the product fraction (density >3000 kg/m3), the percentage Fe varied between 35% and 67.2%. The bulk of the material (88%) actually had a density greater than 4000 kg/m3 and a Fe content that varied between 63% and 67.2%. At a density interval of 3600 to 4000 kg/m3, the Fe content varied from 37% to 60% with an average of 45%.

Jan 1, 2006

By J. Yianatos

The cleaning circuit operation and its effect on the plant metallurgical performance, was characterized at Los Pelambres concentrator, Chile. Experimental data from columns, scavenger and regrinding stages was evaluated. Each stage was characterized by size fractions, and the interaction between stages (columns, scavenger, regrinding) as well as the effect that circulating loads had. The approach for describing the flotation equipment operation (cells and columns) considered the collection and froth zones separately. This methodology allows for the identification of the impact that particle size distribution has on the actual collection and froth transport processes, independently. In this way the effect of regrinding on flotation recovery and grade can be related to the corresponding operating variables, e.g. pulp flowrate, air flowrate, pulp level and pulp density, among others. The effect of gangue entrainment was considered using an empirical dimensionless correlation. The interaction between the circulating load and the overall performance of cleaning circuit was evaluated. The circulating load was defined as the ratio between the solid flowrate of scavenger concentrate over rougher concentrate. It was found that the overall cleaning flotation circuit (column-scavenger) can operate at a relatively high and constant recovery for a wide range of mineral treatment. This is possible when the scavenger has the capacity for compensating the decrease in column recovery at larger circulating loads. Under the condition of high overall cleaning recovery, the rougher stage closely represents the plant recovery. However, at large mineral treatment conditions, the design characteristics (e.g. concentrate transport channel capacity and transfer boxes) as well as instrumentation, control facilities and operation, became bottle-necked. A simulator was developed using empirical models for each stage (column, scavenger and regrinding) in order to evaluate proper operational strategies for cleaning flotation circuits Keywords: flotation, cleaning, regrinding, Vertimill, simulation.

Sep 1, 2012

By L. H. Shang

The 319 Al-Si alloy is one of the most prominently used aluminium-based alloys in motor vehicle and engine applications, Microporosity present in 319 alloy castings reduces the load bearing capacity of the castings, The quantitative prediction of microporosity levels in Al-Si castings has been a subject of much interest for several years. In this research a new criteria function, tf 1,98 R13° (tf: local solidification time, R: cooling rate) was developed by multiple regression analyses, correlating thermal data from simulation studies to experimentally obtained microporosity values. This new criteria function gives a general prediction of microporosity in 319 Al-Si castings.

Jan 1, 2005

By Duong Huu Hoang, Nathalie Kupka, Urs A. Peuker, Martin Rudolph

"The froth ability, froth stability and the froth structure are strong influences in flotation process i.e. on water recovery, bubble size, entrainment of gangue particle, flotation rate constants, grade and recovery. The labscale flotation of rich apatite ore with a high mass pull leads to significant changes in pulp and froth properties over time. The froth stability decreases with increasing the flotation time. These changes can be related to different solid contents, reagent concentration, froth heights and bubble size distributions. This study presents the results from froth studies and discussions on the particle size of fully liberated silicates and degree of entrainment based on automated mineralogy size-by-size analysis. The change of entrainment in a rich apatite ore batch flotation with time will describe more precisely by measuring froth properties using a Dynamic Foam Analyzer. It is concluded that the degree of entrainment is not only dependent on particle size but also the pulp density due to its effect on particle settling and also froth properties in varying resistance to particle drainage. Furthermore, entrainment models are applied to predict the effect of size, flotation time on entrainmentINTRODUCTIONFroth flotation belongs to the group of heterocoagulation separation techniques. Froth flotation is classically divided into two active zones, the pulp zone (where particle collection occurs) and the froth zone. A schematics drawing of the interaction between both zones is plotted in Figure 18 (Yianatos and Contreras, 2010). In froth flotation, the collision probability in the collection zone is governed by the physics of the process or hydrodynamics (Wills and Finch, 2016). The true flotation event in the pulp occurs when the hydrophobic valuable mineral particles collide with bubbles and formation of a stable particle-bubble aggregates moving upwards against gravity to the froth phase (Yianatos et al., 2009)."

Jan 1, 2018

By J. Tuzson, H. McL. Clark

Introduction Wear of pumps, wet cyclones and pipelines by suspended solid particles will impact their operating economies by limiting their useful life, reducing their reliability and increasing the amount of servicing. Erosion is considered a materials problem. The empirical solution consists of testing different materials in field applications. Such tests are time consuming and expensive. The prediction of localized wear rates, life estimates and appropriate material selection demand a better understanding of the slurry wear process in environments corresponding to those found in working equipment. Key words: Wear, Slurry abrasion, Coriolis erosion tester The slurry wear process Solid particles suspended in liquid generally move with the flow, but such particles deviate under the centrifugal and Coriolis forces encountered in pumps. The concentration of particles will increase, and a solid layer or bed may accumulate if the acceleration is directed against the flow passage wall. Large particles in dilute suspensions may impact the wall. dissipating their kinetic energies and removing material. However, particles smaller than about 11)(1 µm encounter great drag when moving through the liquid. and such par¬ticles have little kinetic energy left when they reach the wall. They cannot penetrate the stagnant boundary layers present in pumps. Therefore, small particles tend to form beds that slide along the wall, removing material by a process that could he called sliding erosion or wet abrasion. Wear by impact erosion from large particles in dilute slurries can he predicted by appropriate analytical and empirical methods. However, laboratory tests and calculations of wear rates that correspond to sliding erosion are more likely to correlate with field experience from wear under similar conditions. Specific energy Data from laboratory slurry erosion experiments have shown that the amount of material removed is approximately in proportion to the energy expended in the erosion process. Thus. the specific energy-energy expended in removing by erosion a unit volume of material-offers a simple, practical measure for the erosion resistance of materials. The concept was found to also apply to sliding erosion (Clark et al.. 1997). Generally, the study of the material-removal process in slurry erosion continues to remain a subject of research. Conceptually, if the flow velocities and accelerations could be calculated in a pump or pipeline, the energy dissipated at the passage walls could also be estimated, and the material removal rate would become known from the specific energy determined by laboratory tests. Slurry erosion testing Laboratory devices made specifically for slurry erosion testing may be grouped into the following: jet erosion devices, slurry pots and the Coriolis test machine (Pagalthivarthi and Helmly, 1992). Jet erosion devices use a slurry pump and nozzle to produce a high-velocity slurry jet that is directed at a flat material specimen, either perpendicularly or at some acute angle. Combined impact and sliding erosion are produced. but the processes cannot be separated, and the wear is difficult to assess except by weighing. Slurry pots consist of a cylindrical vessel containing the slurry of interest. In the slurry pot, test specimens are attached to a rotating arm. The samples are rotated in the slurry and experience local flow conditions that result in combined impact and sliding erosion. Wear depth measurements from detailed laboratory experiments have been successfully correlated with results from an analytical model of the process, and specific energy values have been calculated (Wong and Clark, 1995). In industrial use, the samples are weighed to determine the total material loss. Materials are ranked with respect to some reference material. The Coriolis erosion tester (Tuzson, 1984) consists of a rotor with a central cavity, from which two opposing radial passages lead out (Fig. 1). The slurry is fed to the centerof the rotor in one pass from a stirred overhead tank. The slurry particles are subjected to the Coriolis acceleration as they flow out through the radial passages. The material specimens are mounted into the radial passage walls facing the direction of rotation and are eroded by the particles that are pressed against them as they flow out radially. A narrow groove is worn into the sample within a few minutes, using a few gallons of slurry. Material removal is estimated accurately from profilometer traverses across the wear scar at different locations. The energy dissipated by the particles can be estimated, which leads to a well-defined experimental value for the specific energy.

Jan 1, 2000

By J. HUNER

Twenty-four new fields were found in Louisiana during 1945. Of this number 15 were oil fields, eight were gas condensate, and one a dry gas field. None of these fields, with the exception of West Delhi, is as yet of any great consequence. The Weeks Island field in Iberia Parish may eventually develop into a considerable reserve.

Jan 1, 1946

By J. P. Neumann, Y. A. Chang

Lattice parameter measurements of the hcp phase in the system Ag-A1 near the stoichiometric composition Ag2Al were carried out for specimens quenched from 825°K, annealed for 10 days at 453°K, and annealed for 100 days at 413°K. The three heat treatments resulted in the same lattice parameters at room temperature. None of the specimens showed any superlattice lines. The lattice parameters of this alloy were also measured at temperature from 77° to 750°K. An anomaly in the temperature variation of the lattice paramete.rs occurs in the region near 400°k, which may be associated with local ordering. FROM measurements of the diffuse scattering of X-rays, it is known that the [ phase in the system Ag-A1 near the stoichiometric composition Ag2A1 ex- hibits a considerable degree of short-range order at room temperature.&apos; Moreover, based on the position of the short-range order peaks a superlattice model had been proposed in the same study and it was suggested that lowering the annealing temperature to 420°K might result in long-range order. In the present study, the diffraction patterns and the lattice parameters of three differently heat-treated specimens, i.e., quenched from 825°K, annealed for 10 days at 453°K, and annealed for 100 days at 413°K, were determined from 77" to 750°K. The purpose of these measurements was to investigate 1) whether long-range order could be established by prolonged annealing and 2) whether the lattice parameters at room temperature depended on the heat treatment, since it had been proposed earlier2 that the lattice parameters in this phase are related to the atomic arrangement. 1) EXPERIMENTAL TECHNIQUES Silver and aluminum, both 99.99 pct purity, were melted in a zirconium oxide crucible under helium in

Jan 1, 1969

By Daniel Murray

"ACCIDENT PREVENTION in and around coal mines presents many problems of a type which are not encountered in any other industry. This is particularly true of the coal mines in Nova Scotia, where the underground workings are very extensive and the area of exposure to workmen is very great.Roof conditions at the coal faces and in the waste change very rapidly, almost from hour to hour, and it is at these places that the greatest dangers exist and where most mine accidents occur. It is only natural, therefore, that our attention, as far as accident prevention is concerned, should be concentrated •at the coal faces and in the waste, especially in mines where the longwall system is used in the operation •of the seam.It has been said that no hard and fast rules can be set down for timbering at the coal faces and in the waste in the coal mines in this area. We do not subscribe to this theory, however, for the following reasons:On the longwall faces in No. 18 Colliery of the Dominion Coal Company, Limited, where the 'Dosco Miner' has been in operation and where there is a very rigid system of timbering and roof supports, which is strictly followed, only one compensable accident has occurred on those faces from May 2ndJ 1950, to the time of writing this paper, February 3rd, 1953.The 'Dosco Miner' has worked on four different longwall faces in this mine and has mined and loaded some hundreds of thousands of tons of coal."

Jan 1, 1953

By H. E. McKinstry

MOVEMENT on a fracture of irregular shape can cause local widening of the fissure and thereby offer freer channelways for circulation of ore-depositing solutions. This influence, coupled with large areas of wall rock available for reacting with ore solutions in brecciated and shattered ground can account for locally active deposition of metals and the resulting ore shoots. Such irregularities in the fracture system may be caused by local variations in the strength of rocks and by pre-existing lines of weakness, especially if these stand at favorable angles to certain components of the fracturing stress. Therefore correct interpretation of the mechanics of fracturing should permit deductions as to structurally favorable places on unexplored portions of the vein system. INTRODUCTION IT has long been recognized that movement on a curved or irregular fault surface is capable of separating the walls in certain portions of the fault, but until very recent years the importance of this mechanism as a factor in localizing ore shoots has escaped proper recognition. A short time ago W. H. Newhouse&apos; presented a careful analytical study of displacements and their corresponding open spaces. For reasons that will be discussed later, it frequently happens that portions of the vein which are favorably oriented are not merely wider but also richer than the average. In many cases the widening with its accompanying richness coincides with very minor changes in the dip or strike of the vein, irregularities that commonly escape notice unless the vein is mapped in detail and a careful geometrical analysis made. While the relationship between the width of the vein and the changes in dip or strike has been recognized as a matter of observation, the irregularities have been accepted as more or less the result of accident. There has been very little effort except in isolated cases to find out the causes of these changes in dip or strike. Yet it is clear that if the causes can be recognized and expressed in terms of geologic structure the geologist will know where to look for repetitions of these favorable conditions either on extensions of the same vein or on adjoining veins. Any lack of understanding of the causes is due to the limitations of our ability to interpret our observations and not to the sheer capriciousness of

Jan 1, 1941