Search Documents

By C. Patrick

Annually, the U.S. coal industry generates and must dispose of over 200 million tons of coal refuse, expanding a major environmental problem. The purpose of this research was to investigate the feasibility of utilizing coal refuse as an aggregate in concrete. This paper reports on findings of the initial phases of a project to determine the viability of replacing traditional concrete blocks, used for under-ground ventilation stoppings, with refuse blocks. Refuse was collected from three active preparation plants in Eastern Kentucky and used as the primary aggregate for concrete cylinders. The refuse fell within ranges normally observed for size consist, moisture, and ash. Stress-strain analyses yielded compressive strengths of the refuse cylinders from 59% to 77% of the control group strengths. Low variability within groups while significant differences between groups were found. On-going determination of effects of weathering on the refuse cylinders is being conducted and will be completed in early 1995. The research results are favorable for the future direction of the overall project objectives.

Jan 1, 1995

By Paul S. Goodman

This report examines absenteeism and accidents. The first section provides some background information on absenteeism. The second section examines trends in absenteeism in underground coal mines over time. The third section examines causes of absenteeism. Models were examined. The first model looks at self-report reasons for absenteeism. The second examines demographic correlates of absenteeism. The third model includes demographic and attitudinal predictors of absenteeism. The next section of the report examines the effect of absenteeism on accidents. The last section contains strategies for reducing absenteeism.

Jan 1, 1985

The revised estimate of coal production in January 1977, is 39 million tons -- down 12 mi 11 ion tons compared with production in January of last year, largely as a consequence of the snow storms and cold. The major coal-hauling railroads operating in Eastern and Midwestern States reported to the Bureau of Mines that they loaded approximately the same number of cars for the week ended February 5, as in the preceding week. The Bureau of Mines estimates that U.S. coal production for the week ending February 5, 1977, was approximately 8.5 million tons, or nearly 3.5 million tons less than production for the corresponding week in 1976. Coal production from January 1 - February 5, 1977, was approximately 47.8 mi 11 ion tons compared with production of 63.5 million tons for the corresponding period in 1976. As of the first week in February, river and truck shipments of coal in the Eastern U.S. were about one-half of the normal traffic. Despite the freezing weather and ice and snow conditions of rivers and highways and reduced rail shipments, there was reportedly little or no shortage in coal supply to consumers. Inventories at electric utility plants and steel company coke plants at the beginning of the severe weather were sufficient in most cases for at least 30 days" operations. There have been no reports of coal shortages at other industrial plants.

Jan 1, 1977

By D. L. Pitt

This paper, describing the milling methods at the concentrator of the Premier Gold Mining Co., Ltd., Premier, B. C., Canada, is one of a series being prepared by the United States Bureau of Mines on milling methods and costs in the various mining districts throughout the United States and Canada. ACKNOWLEDGMENTS The authors wish to acknowledge the assistance and suggestions given during the preparation of this paper by the engineering staff and accounting department of the Premier Gold Mining Co., Ltd., all of whom have assisted materially in gathering the data used.

Jan 1, 1933

By A. A. McCloskey

APPROXIMA TEL Y 95 percent of Waite-Amulet's Lower A orebody will be mined by diamond-drill stoping. This method of stoping was developed, and has been successfully applied, at the Noranda mine in recent years(1) and is now used in several base-metal and gold mines in north-western Quebec and in other parts of Canada, South Africa, and Australia. The purpose of this paper is to deal with the features of the Lower A ore-body which led' to the adoption of this method of stoping, and in addition to give a general description of stope layout, stope development, main haulage development, chutes and grizzlies, diamond drilling for stope blasting, diamond drilling and equipment, primary blasting, secondary blasting, haulage and loading, ore pockets, pumping and drainage,. and shafts at Waite Amulet. Figure 1 is an isometric projection of the orebody, illustrating the mining system. The factors that led to the adoption of diamond-drill stoping of Lower A orebody are as follows: (1) Safety.0 (2) Size and shape of the orebody, and depth of the orebody below surface. (3) Strength of the hanging-wall, footwall, and sulphide ore. (4) Continuous ring-drilling from sub-level drifts, with no delay for blasting. (5) Large-tonnage blasts at the end of Saturday afternoon shift, after ali men are out of the mine. (6) Sub-levels may be retreated from top to bottom simultaneously, or lower sub-levels may be retreated first without any change in the ring-drilling la yout. (7) Large stopes up to 100 feet wide can be mined, leaving substantial pillars up to 60 feet in width, which may be partially recovered by âiamond~drill stoping or by other stoping methods. (8) A large tonnage may be drilled-off in advance of blasting, but only a supply of unoxidized ore for flotation treatment is blasted. (9) Better ventilation during working shifts. (10) Gravity flow of all broken ore to grizzlies located in the footwall of the orebody. (11) Electric blasting by a crew of two men.

Jan 1, 1941

By R Billingham

QueenslandÆs new safety legislation for metalliferous and coal mining (Mining and Quarrying Safety and Health Act 1999 and Coal Mining Safety and Health Act 1999, together with the Regulations) came into effect on 16 March 2001. The legislation places clear obligations on mine owners, operators and workers to have a safe place of work and to manage risks to safety and health. It also places obligations on contractors, designers and providers of services. The legislation is non-prescriptive in that it states what outcomes must be achieved and not what must be done. The key issue is that the risk of injury to people must be at an acceptable level. The legislation creates a Mines Inspectorate with powers of inspection and audit of mines, their safety management systems and the management of risks. Auditing of the risk management process is carried out against standard risk management techniques and directives for corrective action may be issued when audits reveal non-compliance or unacceptable levels of risk.

Jan 1, 2002

By T. Reed Scollon

Before we can attempt to answer the question of what can be expected from coal research, let us examine why research is done in other fields and what others expect for the money they spend on research and development. Up to 1900 almost all organized research was carried out at universities. Most of the support came from the university, and by present standards the amount of research was extremely small. The motivation for university research was basically discovery of new phenomena, with the objective of advancing knowledge. Side by, side with this organized effort was that of individual inventors who were primarily responsible for applying this new-found knowledge to useful purposes. During this period inventors were rarely supported by anyone, and experimentation was carried out either in their spare time or at the expense of earning a living. Men like Edison, I believe, were the first to demonstrate on a large scale that one could systematically apply newly discovered scientific principles to inventions that would serve useful purposes and would return a profit to those engaged in the effort. The tremendous expansion in research therefore began with the realization and demonstration that the scientific discovered could be applied in such a way as to return a' handsome profit to those who invested in it. The motivation of many of the research personnel however, remained the satisfaction associated with new discoveries, The money to support their efforts came from those interested in a return on their investments. Since the First World War and a rapidly accelerating rate since the Second World War another important motive for supporting research has appeared--the needs associated with national defense; this type of research has been supported almost exclusively by the Government.

Jan 1, 1959

By Robert Hopler

A detonator is a copper tube about a quarter of an inch in diameter and an inch and a half long, closed at one end and containing in the closed end a small charge of fulminate of mercury, which has been found to be the best explosive for detonating dynamite. The fulminate charge is a very powerful explosive very sensitive to friction, lows or heat and very poisonous. When exploded it has an intense local action, shattering things in its immediate vicinity, but not extending very far away from the explosion. This kind of detonator is intended to be exploded by a spark from burning fuse.

Jan 1, 2014

By James Westfield

Uranium activity has introduced a comparatively new hazard to United States mining. In addition to the hazards common to all mines, uranium mines have a complex health problem of radiation damage. Like many new processes, radiation and nuclear energy can be made to serve man in many useful ways when properly understood and handled; but, like fire, gases, and electricity, their potential dangers must be known and respected, and appropriate precautions must be taken or death may result. Since 1950 the Public Health Service has been conducting basic investigations on exposure to radon and its daughter products and the effect of exposure upon the health of miners in uranium mines of the Western States. The Bureau of Mines assisted in several of these investigations, especially in mines on Indian lands. The studies have shown that a serious health hazard exists from radioactive exposure that might cause lung cancer if continued over a number of years. The Public Health Service report, Control of Radon and Daughters in Uranium Mines and Calculations on Biologic Effects,6/ shows that 55 percent of the uranium mines employing 64 percent of the miners had atmospheric concentrations more than five times the working level now accepted as reasonably safe for industrial exposures. Extensive control measures are necessary to reduce these concentrations to the suggested working level of less than 300 micromicrocuries of total radon daughter products per liter of air.

Jan 1, 1958

By A. Hasko

Phytoremediation is a new low cost alternative technique for remediation of contaminated soils from heavy metals that are emitted by ferrous and nonferrous mining and extracting processes. It is based on the possibility to use several plants that accumulate high level of metals in order to remove metallic pollutants from soils and render them harmless. Phytoextraction is an adjacent new technique that uses these hyper-accumulator plants in order to extract the metals from them using even the conventional smelting or refming processes. In our previous work, an extensive investigation of about 150 plants have been carried and several species were identified that could be used for nickel phytoremediation and phytoextraction because of their high accumulation of nickel. It has been found that five taxa from Alyssum genus specie had the highest ability to accumulate nickel with concentrations more than 10000 ug/g (dry weight) or 1%. The taxa showing the highest accumulation of this metal is Alyssum murale var. chlorocarpum with 28 600 ug/g or 2.86%, a good candidate for Phytoextraction. In this work, in order to optimize the phytoremediation and phytoextraction processes further Absorption Spectrometry measurements and biological studies were carried out to determine the parts of the plants that accumulate the highest amount of nickel and the best biological cycle during which they accumulate the highest amount. The results show that the greatest accumulation of nickel occurred in the leaf material (2.86%) and the least in the roots (0.43%). The investigation of the biological cycle of the genus Alyssum showed that: (1) the seeds germinated between 50 C to 30 0 C and more in 25 0 C; (2) 62.9 % of seeds germinated at A.m. var. chlorocarpum; (3) the emergence is almost continue from March to April; (4) the anthesis occurs from May to July; (5) the ripening of the fruit takes place 30 days after flowering; (6) the dissemination of fruits occurs from September to October. Due to these special characteristics it is reaffirmed that Alyssum murale var. chlorocarpum, as a nickel hyperaccumulator, is the most promising plant to be used for feasible phytoremedation and phytoextraction purposes. Keywords: Key words: Phytoextraction, PhytoRemediation, Nickel accumulators, Alyssum sp., Biological cycle

Jan 1, 2003

By L. M. Gochioco

The U.S. coal industry is under-going dramatic changes to meet the challenges of the keenly competitive fuels market. The application of innovative technologies is needed to improve safety and to increase productivity in order to make coal more competitive as a fuel. As more coal companies shift into capital intensive longwall mining, there is a clear need to invest more in exploration before mine plans are made. Coal seam anomalies may create adverse mining conditions. The early detection of these anomalies could make the longwall mining safer and more productive through improved planning. A standard exploratory drilling program can provide only limited geologic information. The seismic reflection technique can be used to detect coal seam anomalies and is effective in reconnaissance surveying. Recent advances in the quality of coal seismic data have increased the success rate of seismic surveying. Therefore, surface seismic surveys, coupled with selective drilling, will come to play an integral role in coal exploration in the 1990s.

Jan 1, 1990

By Kung-Lee Wang

This Bureau of Mines study illustrates the economic significance of the Florida phosphate industry to the State and to the Nation. Environmental considerations related to phosphate industry activity are discussed briefly. Based on forecasts of Florida phosphate production in 1975, and using 1972 dollars, regional and national output value, income, and employment created by the phosphate industry were estimated for 1975. State and Federal government tax revenues generated by the phosphate industry, are also measured. Further, the concentrated impact of the phosphate industry on certain Florida areas and on regional industries is examined. Finally, the phosphate industry's importance to the U.S. balance of payments, U.S. agricultural production, and the Frasch sulfur industry is considered, in addition to byproduct fluorine, and potential byproduct uranium from fertilizer manufacturing.

Jan 1, 1974

By Daowu Yang, Zhuo Ren, Hui Liu

"In this paper, the photochemical catalysis degradation effect of photocatalyst obtained by charcoal-supported nano TiO2 (nano TiO2 / charcoal) on the formaldehyde in the air was studied. The influences of the nano-TiO2 loading and the photoreactor structure on the efficiency of photochemical catalysis degradation of formaldehyde was reviewed.The nano - TiO2 / bamboo charcoal adsorption of formaldehyde, as well as the influences of a certain amount of formaldehyde after adsorption on its photochemical catalysis effect were discussed. The sol preparation process of Ce-doped nano-TiO2 was described. Experimental results indicated that: the surface of bamboo Charcoal still has a strong formaldehyde adsorption capacity after Supported by Nano TiO2.After adsorbing formaldehyde, the photochemical catalysis degradation efficiency of formaldehyde of the catalyst at a steady state is basically the same with new prepared catalysts’. When the thickness of the catalyst layer of the multi-ladder-type structure photoreactor is 2mm, the interval is 20mm, the absorption efficiency of formaldehyde of Nano- TiO2 / bamboo charcoal is the best . Nano-TiO2 undoped Ce responded with no degradation of formaldehyde after 2 hours, while the degradation rate of formaldehyde of the Ce-doped nano- TiO2 reached 15% 2 hours late, and the formaldehyde decontamination of the equipment reached 94%.IntroductionEmerging out of home decoration in the distribution of formaldehyde, benzene, ammonia and other indoor pollutants have been proved to be very harmful to the human body. Photocatalysis can eliminate air pollutants, in particular, can effectively degrade the air volatile organic compounds, it is a new method of air purification developed in recent years. the biggest advantage of photochemical catalysis degradation is green, this method can be available at normal temperature and pressure to degrade formaldehyde and other organic matter into carbon dioxide and water without secondary pollution.Nano-TiO2 have become the most studied photocatalyst due to its stable, non-toxic harmless, superior photochemical catalysis properties [1]. Initially nano-TiO2 powder was used as a photocatalyst, but it’s difficult to recover and easy to wear and tear [2,3]. Later, the TiO2 was used in the form of film loaded on some carriers, such as glass beads [4]. As the photochemical catalysis reaction occurred on the catalyst surface, only the organic matter adsorbed on the catalyst surface can be degraded, so the catalyst was requested that must have a strong adsorption. Combined the adsorption properties of bamboo charcoal and the photochemical catalysis activity of nano-TiO2 together. Made the photocatalyst by loading the nano-TiO2 on bamboo charcoal to degrade organic matter in the air. Nano-TiO2 semiconductor photocatalyst has a strong catalytic oxidation due to the photo generated hole of the surface [5,6],and has a potential application. Some studies have shown that nano-TiO2 photocatalysis activity can be increased by doping certain metal ions [7,8].The aim of our work in this study was to use bamboo charcoal load Ce-doped nano-TiO2 photochemical catalysis oxidation to degrade formaldehyde,and design a multi-ladder structure photoreactor, also prove the availability of the device from the theoretical and experimental."

Jan 1, 2011

By Clyde E. Williams, V. N. Krivobok, C. H. Herty

THE extreme effect of the depression on the steel industry is well illustrated by the fact that the amount of iron ore shipped from the Lake Superior district was the lowest in 47 years. Something over 3 1/2 million tons of ore was shipped in 1932, compared with over 65 million tons in 1929. It is not surprising then that practically no advancement in iron ore beneficiation has been made. Improved research and development work, however, was continued at the Michigan College of Mines in the survey of the lean iron ores of Michigan with reference to the possibility of their concentration; at the University of Minnesota in its large-scale jigging studies of Lake :Superior ores; and at Battelle Memorial Institute in the development of improved jigging of iron ores. The successful operation of the new Hadsel mill at a gold property in California gave such low grinding costs on a quartz ore as to give much encouragement in the iron ore industry for a cheapening of the cost of grinding lean ores for concentration.

Jan 1, 1933

By Ed McConaghy, P. LaRochelle

The Ambatovy Nickel Project comprises the development of mine, hydrometallurgical processing facilities and necessary infrastructure in Madagascar, positioning Ambatovy as one of the world’s largest producers of nickel and cobalt from lateritic ore. SNC-Lavalin successfully provided comprehensive Engineering, Procurement, Construction Management (EPCM) services for this major capital project which, apart from its sheer size, scope, and engineering design, represented significant location, infrastructure, labour, environmental and climatic challenges. Today, the project has reached 90% of its nameplate capacity and is in its final performance optimization stage. This paper will discuss the significant project management effort that was required to successfully address the complexity of this major project. It will cover the main project management control systems and the engineering tools and processes used during the detail engineering, procurement, and construction phases to achieve optimum project execution.

Jan 1, 2015

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed, Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963

By AIME AIME

LOCAL COMMITTEES. EXECUTIVE.-W. A. Lathrop, Chairman; R. V. Norris, Secretary; S. D. Warriner, Treasurer; Irving A.. Stearns, W. J. Richards, H. S. Drinker, C. D. Simpson. GENERAL RECEPTION.-Irving A. Stearns, Chairman. Archibald, James, Jr., Pottsville. Lawall, E. H., Wilkes-Barre. Ashley, H. H., Wilkes-Barre. Lentz, W. 0., Mauch Chunk. Ayres, WV. S., Hazleton. Lewis, Albert, Bear Creek. Beard, J. T., Scranton. Loomis, W. H., Jeddo. Bridgman, J. C., Wilkes-Barre. Markle, Alvan, Hazleton. Bunting, Douglas, Wilkes-Barre. Markle, John, Jeddo. Chase, F. M., Wilkes-Barre. Neale, J. B., Minersville. Coroner, Eli T., Scranton. Norris, R. V., Wilkes-Barre. Cote, E. B., Jr., Drifton. Oliver, Paul A., Oliver's Mills. Davies, W. H., Hazleton. Owens, W. D., Pittston. Davis, H. G., Dorranceton. Pardee, 1. P., Hazleton. Dodge, W. F., Wilkes-Barre. Quin, R. A., Wilkes-Barre.

Jul 1, 1911

By Joe Silvestri, James Carroll, Steve Rondinelli, Raelene Shelly, Jason Miller

"The I-70 Eisenhower-Johnson Memorial Tunnel (EJMT) Fixed Fire Suppression System (FFSS) will help protect the traveling public as well as the entire tunnel itself, which is a critical asset of the Colorado highway system. This project is part of an effort to avoid any closure or long-term damage to these tunnels after a fire event. Historically, the EJMT complex has experienced two to three fires a year. While CDOT has firefighting capability at the EJMT complex, the fixed fire suppression system will provide first responders the critical time needed to safely approach the scene and take action, and is a necessary tool in combating tunnel fires, keeping the public safe, protecting the tunnel structure, and minimizing disruptions to traffic. This paper provides a case history of the first-of-a-kind design and construction of the EJMT FFSS. Major project elements include; water-only deluge fire suppression system, fiber optic linear heat detection system, updated fire alarm system and new drainage system. PROJECT BACKGROUND The I-70 EJMT FFSS was awarded to the Design Build Team lead by Barnard Construction, supported by Rondinelli Life Safety, BCER Engineering, ILF Consulting, Western States Fire Protection and Systems Group. The team conducted successful live fire tests at the Boulder Regional Fire Training Facility in November 2014, with the final design of the FFSS and other supporting infrastructure completed in the spring of 2015. Construction began in early summer of 2015 and the project was completed in December 2015. While CDOT currently has firefighting capability at the EJMT complex, this project features an intelligent linear heat detection system that can accurately identify a fire within feet of its location and subsequently activate the corresponding water-only FFSS deluge zone, bringing water in from an existing supply system on the west side of Loveland Pass. The detection system also activates cameras so the EJMT onsite control room personnel can view and better assess a fire event. The uniqueness of this design is that the majority of the installation occurred above the traffic lanes in the tunnel, which resulted in minimal impacts to motorists below. The fire suppression system will help protect the traveling public as well as the tunnel structure, a critical asset to the highway system. This project is intended to reduce damage and avoid long-term closures of the tunnel due to fires. A long-term closure could cost Colorado billions of dollars and negatively impact tourism along the I-70 mountain corridor."

Jan 1, 2016

By J. B. Zadra

The use of activated carbon for extracting gold and silver from pregnant cyanide solution and pulp has been investigated many times. The primary advantage of this use of activated carbon is that .the dissolved values can be recovered from slimy ore pulps or from slime portions of ore without settling and thickening or filtering. The loaded carbon is removed from the barren pulp, and the pulp can then be discarded. Activated carbon has been used recently in treating gold ores containing very little soluble silver. When the carbon was loaded with a suitable amount of gold, the silver load was negligible. The remaining problems concerned the removal of the gold from the carbon, the recovery of the gold as bullion, and the reuse of the unloaded carbon. As described in a recent report, a method that solved these problems was developed. The gold-laden carbon was leached with caustic sodium sulfide solution and the gold simultaneously recovered by electrolysis. Both the carbon and the spent solution can be reused. That process was applicable to gold-laden carbon only. It was not applicable to carbon carrying silver, because sodium sulfide does not leach silver from carbon but "fixes" it. It has been necessary, therefore, to develop a modified process for the removal or desorption of both gold and silver from loaded carbon. This modi¬fied process permits the use of activated carbon for extracting both gold and silver from gold ores carrying enough silver to have economical interest or in which silver may be the predominating value.

Jan 1, 1952

By E. S. Geskin

"This paper is concerned with the construction of a formal technique for the selection of a metallurgical technology. Exergy consumption is used as the criterion of process efficiency. Different items of the exergy balance are considered and techniques for the reduction of exergy consumption are determined. The selected techniques of exergy saving enable us to identify processes which should be used at different stages of steelmaking. The combination of the selected processes enables us to suggest a technology for conversion of iron ore into steel products. The selection of this technology narrows the range of further search of metallurgical processes. The paper shows that qualitative thermodynamic analysis can be used as the first step in the design of metallurgical processes. IntroductionThe existing processes for making, shaping and treating of steel enable us to convert the available iron bearing ores into marketable steel products. However, the energy cost of metal production is much higher than thermodynamically required, while the metal properties are much lower than thermodynamically available. Increasing cost and declining availability of energy and raw meterials make the creation of new steelmaking technologies imperative. In recent years, the number of novel processes for the making, refining, and shaping of steel have been suggested and tested. Some found a practical application. However, the tested technologies make up a small portion of the physically available routes for the conversion of iron ore into a marketable product. It is also not evident that the optimal routes have been tested and that the selected technologies are the best among those tested.Although the development of new metallurgical technologies must be based on the experimental and practical information, the number of the alternative routes for the making, shaping and treating of steel, as well as the cost of examining each single route, make necessary the use of analytical techniques for the evaluation of the possible ways of process development."

Jan 1, 1988