Search Documents

By C. O. Hawk

As an exploratory effort to produce useful products from coal by a new path, the Bureau has made a few experiments on the fast heating of finely ground coal particles by irradiation with a flash of high intensity light. The flash was produced by an electrical discharge at high voltage through a xenon-filled tube. The flashes lasted from 2 to 3 milliseconds. The reaction took place in small sample tubes, ½ inch-dimeter by 4 inches long, and with small amounts of coal (total amount charged 0.1 gram, probable effective amount not more than 20 milligrams). Average particle size of the coal, estimated on a numerical basis, was 20 microns. Temperatures reached were evidently quite high, because all products obtained in quantity were characteristic of high temperature pyrolysis. Apparently, conversion of the coal was extensive where isolated particles received the full benefit of a flash. It seems particularly significant that acetylene was present in appreciable amounts--comprising almost 3 percent of the total gaseous product in one case. This is good evidence of a short heating period to very high temperature (well above 1,000° C) followed by rapid quenching. Although the results are interesting, they do not suggest any immediate practical application.

Jan 1, 1963

By James S. Browning

The Mineral Resources Institute of The University of Alabama conducted research on the removal of sulfur from coal using a combination of gravity concentration and flotation methods. The research utilized the gravity and centrifugal force capabilities of the Humphreys spiral to remove part of the pyritic sulfur and ash. Flotation of the Humphreys spiral coal concentrate removed additional sulfur and ash to yield products that conform to Federal air quality standards for sulfur oxide emissions. The clean coal products recovered by the combined process contained 7.7 to 8.0 percent ash, 0.12 to 0.16 percent pyritic sulfur, and 0.78 to 0.96 percent total sulfur. Pyritic sulfur rejection by the process was about 95 percent. In addition to obtaining good recoveries of high quality coal the tests demonstrated that the pyrite in the wastes could be isolated as enriched flotation products by the combined gravity - flotation apporach. Pyrite concentrates analyzing 25 to 33 percent sulfur were recovered. Potential benefits of the pyrite flotation step are recovery of a product of possible market value and the elimination of the pyrite from the waste ash which could be a potential acid water problem when impounded.

Jan 1, 1981

By R. W. Stahl

An emergency is defined as an unforeseen combination of circumstances that calls for immediate action. When applied to a coal mine, an emergency may call for prompt removal of the men to the surface through travelways other than the haulageway or intake airways, which are generally contaminated with irrespirable air as a result of an explosion or fire. Therefore, maintenance of adequate and travelable escapeways from all working areas of a mine is vitally important insurance against disaster. Several mine disasters could have been avoided if well-defined escape routes had been provided and made known to all mine employees. Such occurrences, unnecessary as they generally are, unfairly indict the industry when only a small segment thereof is involved. As a result of a rather recent disaster, which might not have happened if good escape routes had been provided, the Bureau of Mines decided to delve into the escape procedure to determine (1) what is being done in the industry and (2) what might be done at reasonable cost.

Jan 1, 1962

By M. S. Millman

Close monitoring of performance at each process stage, from raw material through to finished product, is vital for operational consistency and the production of high quality steel. However, many of the integrated iron and steelmaking process route stages operate under such severe conditions of temperature, dust, water, thermal radiation, vibration, pressure, vacuum, extreme dynamic events, high material flows, corrosion, erosion, electrical-noise, electromagnetic-noise, or audio-noise that, in general, it is a very difficult challenge to obtain useful information for control. Thus, state-of-the-art non-contact and remote sensors are applied to help monitor and control specific process operations. Often, these sensor systems have been developed especially for the steel industry and they are based on four principal technologies: Laser, Microwave, Electro-Magnetics and Thermal Imaging with supporting technologies such as: X-ray Fluorescence, Audiometry, Digital Image Processing, Radio Telemetry, GPS and many others. These advanced sensor technologies are reviewed with respect to their application at various stages along the integrated process route.

Jan 1, 2004

By Laxman S. Sundae

Laboratory tests were conducted at the U.S. Bureau of Mines to determine the effects of roof-bolt drilling parameters on penetration rate in sandstone using tungsten carbide alloy (WC-Co) and polycrystalline diamond compact (PDC) drill bits. During the tests, water pressure of 552 kPa was found to be adequate for removing the cuttings from the tops of drill holes. Test results show that for both types of bits, penetration rate increased when thrust was raised from 227 to 1,588 kg. When water pressure rose from 554± 120 to 1,344±350 kPa, the effect on penetration rate was not significantly different. Conventional WC-Co bits became dull when one or two holes were drilled, after which the penetration rate dropped dramatically. Microscopic examination shows that the cutting edges of PDC bits also become somewhat dull, but at a much lesser rate than WC-Co tips. Microscopic examination also reveals that the wear mechanism of WC-Co and PDC bits is quite different, which may explain the longer life of the PDC bits.

Jan 1, 2010

By Noel Cunningham

MANY excellent descriptions of the mills of the, Porcupine district have been written, but no discussion exclusively devoted to the metallurgical technology has been given. These notes are intended to cover this feature briefly. They are based upon 2 ½ years' mill operation in the district-i.e., practically since the beginning of metallurgical operations. Character of the Porcupine Ore.-There is no oxidized ore in the district, the surface having been deeply planed by glacial action in recent geologic time. The precious-metal content is about in the proportion of 85 of gold to 15? of silver by weight; hence, the silver is practically negligible. There are two classes of Porcupine ore, having very different characteristics; these will be referred to throughout this paper as Class A and Class B. Class A ore is a pure quartz with inclusions of schist. Generally it is heavily fractured .and breaks down readily to sharp, hard grains, about minus 10 plus 20 mesh, requiring further comminution to release the gold. It carries very little pyrite; the gold is entirely free and apt to be coarse, but often spongy, going into solution readily on that account. This gold is 60 per cent. to 85 per cent. free milling, depending on the grade of ore. Class B ore is an iron silicate schist, strongly laminated, carrying 4 to 5 per cent. pyrite; its specific gravity is 2.8 to 3.0, depending upon the amount of mineralization. In breaking the ore in the mine, generally over 25 per cent. of material through a ½ -in. ring is made; the ore readily breaks down in milling and makes a comparatively large amount of non-crystalline slime; owing to its high specific gravity, however, it is quick settling.' In my opinion, the gold in this ore is free, but so finely divided that it will neither pan nor amalgamate; it appears to be disseminated through the rock and not chiefly associated with the pyrite. Veins of Class A ore occur with or without side walls of Class B, and veins of Class B occur unassociated with Class A; more often the veins are closely banded, Class A and Class B alternating, generally with Class B in excess. Both classes of ore are more-or less blocky at times, and with ref¬erence to Class B this is indicative or low gold content.

Jan 3, 1915

Studies of coal reserves have shown that the total augerable reserve base for the United States is estimated to be five billion tons under the current state of mining technology; the potential reserve base at 850-ft penetration is estimated at 20 billion tons. It is with the idea of improving coal recovery, a basic objective of Project Independence, that new concepts, such as modifications and improvements in current machines and development of ways to recover pillars left by current augering, are required. Unless recovery is improved, these potential reserves amount to lost coal.

Jan 1, 1975

"A commercially available through-the-earth (TTE) communications system was evaluated at an active underground longwall mine in West Virginia. This TTE system uses electricfield (E-field) sensing to send text-based communications through two separate antenna arrays connected in parallel. Each antenna array is composed of interconnected, grounded metallic rods or other such structures. Two-way communication between subsurface locations was investigated in this study using various antenna configurations. This field study was conducted as a part of a larger multisite evaluation of available TTE systems in an effort to determine their operational sensitivities. IntroductionWireless, through-the-earth (TTE) communication technology is designed to achieve point-to-point communication through solid strata using very low frequency (VLF) and ultra-low frequency (ULF) electromagnetic waves. Using this approach, communications are established without the need for intermediary communications infrastructure. As a result, TTE systems have the potential to provide reliable, robust communications between surface and underground personnel. Exploration into the use of TTE technology for this purpose dates back to the 1920s (Jakosky and Zellers, 1924; Pittman, Church and McLendon, 1985), but U.S. permissibility requirements slowed the development of TTE equipment for widespread implementation (Durkin 1980; Pittman, Church and McLendon, 1985). One of the primary challenges in producing wireless TTE communications is the counteraction of signal attenuation when propagating through solid strata (Barkand, Damiano and Shumaker, 2006; Wadley, 1949). The long wavelengths of TTE transmissions make them well-suited for reducing the rate of attenuation. However, even when operating within the VLF to ULF range, the performance of TTE systems is still affected by geologic and anthropogenic factors (Geyer, 1973; Geyer and Keller, 1976; Geyer, Keller and Ohya, 1974; Jakosky and Zellers, 1924; Large, Ball and Farstad, 1973). Although commercially developed TTE systems have demonstrated the ability to communicate in a variety of conditions, their range and performance have been highly varied (Barkand, Damiano and Shumaker, 2006; Geyer and Keller, 1976; Geyer, Keller and Ohya, 1974; Ilsley, Freeman and Zellers, 1928; Jakosky and Zellers, 1924; Yenchek et al., 2012)."

Sep 1, 2016

By Sylvan Cromer

THE need for a clear understanding of the physical nature of the flow of gas-liquid mixtures in vertical pipes is ever becoming more apparent. This type of flow is encountered when gas and oil are produced from a well; when water is removed from gas wells with siphon lines and when liquids are elevated by means of air or gas lift. Although a number of investi-gators1-7 have published data on the flow of gas-liquid mixtures, in only a few cases has the experimental setup been devised to permit visual study. In the fields of heat transmission, such as the boiling of liquids and the study of the critical phenomena of the hydrocarbons, researchers have been able to throw additional light on heretofore unexplainable happen-ings through actual observation in glass apparatus. This investigation was therefore undertaken in order to obtain qualitative as well as quanti-tative results for air-water flow. EXPERIMENTAL APPARATUS AND PROCEDURE The flow column used in these tests was made of standard 2-in. pipe and was approximately 98 ft. in height. Pyrex observation sections 2 ft. long having the same internal diameter as the wrought-iron pipe were placed at 14-ft. intervals in the column. The bottom of the tube was cut off square and terminated in the mixing chamber. No perforated nipple or footpiece of any kind was used. To the top of the column was fastened a semicircular return bend having a 4-ft. radius. The flow column was supported by a standard cable-tool drilling derrick (Fig. 1) into which were built observation platforms at each Pyrex section.

Jan 1, 1939

By K. Lapakko

One responsibility of the Minnesota Department of Natural Resources is to encourage the development of mineral resources within the state. A second responsibility is to ensure that mineral development does not adversely impact other natural resources, including the water resources of the state. One approach the Division of Minerals has taken to fulfill these responsibilities is to conduct cooperative research with the mining industry. To encourage mineral development the Division has cooperated with industry on projects related to exploration, mining, and mineral processing. To examine environmental issues the Division has worked in concert with iron ore, base metal, and precious metal exploration and mining companies, as well as the Western Governors' Association, US Bureau of Mines, US Bureau of Land Management, and the US EPA for the past 20 years. These projects were conducted to evaluate methods of predicting, preventing, controlling, and treating problematic mine waste drainages, as well as mine waste revegetation. This paper I) briefly summarizes cooperative projects conducted, 2) enumerates elements which have contributed to the success of cooperative projects, and 3) describes changes implemented for future projects at the Division's new field and laboratory research facilities, as well as at existing mine and plant sites.

Jan 1, 1998

By R McCarthy, P Darvall

FerrAus Limited's Robertson Range and Davidson Creek iron ore projects are located on the far eastern margin of the Hamersley Province, approximately 100 km to the east of Newman, Western Australia. The deposits are primarily formed of bedded haematite-goethite-limonite mineralisation within the Marra Mamba Formation, comprising a total combined resource of 164 Mt at 58.6 per cent Fe. The deposits represent relatively new discoveries for the Hamersley Province. The potential for mineralisation at Robertson Range was identified by Rio Tinto Exploration in 2000, while Davidson Creek remained untested until 2007. One of the main reasons for this is that these deposits are almost exclusively concealed beneath Tertiary sediments and recent transported cover making them difficult targets for conventional, prospecting style exploration. Since commencing exploration in the project area, FerrAus has collected nearly 20 000 stations of gravity data within the Robertson Range and Davidson Creek project areas, with most of this data collected at a 50 100 m station spacing. Gravity has proven itself to be an effective technique at predicting the position of the target host stratigraphy and has been a key driver in the exploration for concealed iron ore deposits. However, there is not always a perfect correlation between the position of gravity anomalies and concealed ore. The response of deep haematite bodies may be masked by low-density cover rocks, while other dense lithologies may be the cause of gravity anomalies which appear similar to the Marra Mamba targets. Hence, effective use of the gravity data requires interpretation in a geologic context with an understanding of the capabilities and limitations of the technique.

Jan 1, 2009

By Melvin W. Kraschnewski

In 1966 Central Ohio Coal Company and Bucyrus-Erie signed a contract authorizing Bucyrus-Erie Company to design and build a 220 cubic yard dragline. This dragline would be used for stripping overburden from their coal reserves located near Cumberland, Ohio. The size of the machine was arrived at after a thorough application study of their annual coal output requirement, depth of overburden and type of terrain. The design and construction of this machine which has been designated by BECO as model number 4250-W is the title of this paper. Size wise based on machine weight the 4250-W represents an increase factor of three over our largest current dragline. Probably the easiest way of presenting a machine of this size is to build it from the bottom up.

Jan 1, 1969

By W. H. Zieman

"THIS IS THE THIRD of the consecutive Annual Forums on Grinding that were instituted by Mr. L. E. Djingheuzian in 1957. The first was on the subject of Ball Milling (Transactions, Volume LX, 1957) and the second on The N on-Cataracting Ball Mill (Trans-actions, Volume LXI, 1958). From the discussions at these forums it was evident that one of the most important factors affecting the efficiency of grinding is the shape of the liners. In order to make a study of liners in use, it was •decided to seek the co-operation of operators across the country by sending out questionnaires requesting basic information. Additionally, these operators were urged to set down briefly any pertinent information on the subject acquired through experience and experiments at their own particular plants. A compilation and analysis of these data were to form a basis for discussion at the Forum on Liners at the Annual Meeting in Montreal, April, 1959. The response of the milling fraternity to this solicitation was most gratifying, and clearly indicated the importance attached by the operators to the effect of liner design upon overall grinding performance."

Jan 1, 1959

By Ian S. Leslie

Seismic monitoring systems for mining operations are being utilized more than ever before in the characterization of rock mass response to underground and open pit mining. This paper provides a review of the use of microseismic monitoring for rock mechanics applications at mines throughout the world. Some practical considerations for the installation of these systems are presented along with techniques for optimizing seismic array coverage. Case studies and installation examples are also provided. Recent applications of advanced seismic analysis techniques are discussed including the determination of event mechanisms, mapping of maximum peak particle velocity (PPV) and seismic hazard fields, and the use of source parameter data for large event re-entry protocol.

Jun 1, 2012

By R. B. Anderson, N. J. Sherren

The mining equipment at the Scully Mine, Wabush, consists of approximately twenty-five large haulage units, eight large dozer-loader applications and seventy other related pieces of service and maintenance equipment. This equipment is operating in sub-Arctic conditions. This pa-per presents a description of the tire maintenance procedures in use here and discusses the tire troubles that are being encountered and the methods of dealing with them.

Jan 1, 1969

By H. B. Jensen

STUDY of the thermal-solution process was begun by treating crushed oil shale in a small autoclave at temperatures of 700° to 950° F. The effect of temperature, reaction time, type of solvent, and richness of shale upon the amount of organic matter that was removed from the oil shale was thus determined. Following this orientation work a semicontinuous, bench-scale apparatus was built so that heated solvent could be pumped through a bed of shale under elevated pressure, thus removing the converted organic matter from the spent shale. After some operating experience had been gained, a continuous unit was constructed. This permitted treating a slurry of shale oil and pulverized oil shale at about 300 p. s. i. and temperatures of 750° to 850° F. for various retention times. Considerable cracking and polymerization of the shale oil were found to take place during the process. In an attempt to prevent this, a study was made of extraction of the shale in batch-type autoclaves under high partial pressures of hydrogen at total gas pressures of as much as 4,300 p. s. i. at 850° F. The thermal-solution process was found to convert over 90 percent of the organic matter in oil shale to oil and gas. The highest yields of gas and oil obtained without hydrogen pressure were equivalent to 119 weight-percent of those obtained from the same shale by Fischer assay. With a high partial pressure of hydrogen, yields equivalent to 126 weight-percent of Fischer assay were obtained. However, the oil produced by thermal solution has a higher boiling range than that obtained by other retorting methods, particularly so if the thermal-solution process is used without a high partial pressure of hydrogen. Nondistillable oil (all benzene-soluble material that would not distill under 2 mm. Hg absolute pressure without cracking) equivalent to over 100 percent of the organic matter in the shale was obtained without hydrogen pressure in the system. When the process was carried out under hydrogen pressure, the yield of nondistillable oil amounted to 60 to 70 weight-percent of the organic matter. Part of this heavy material is formed partly by polymerization and condensation of the shale-oil solvent used. These reactions, as well as cracking of the solvent to form gas and a carbonaceous deposit on the shale, are unfavorable features of the process.

Jan 1, 1953

By Roberto de Moraes

Lunar construction faces unique challenges arising from the nature of regolith and megaregolith. Unlike terrestrial soils shaped by weathering, lunar regolith is composed of angular, poorly sorted particles produced by impacts, with bulk Density, strength, and trafficability varying sharply with depth and terrain. Boulder fields, floaters, and talus aprons add further complexity, disrupting excavation and mobility. Apollo missions documented these conditions through drive-tube samples, trenching, penetrometer data, trafficability tests, and seismic profiling, but the results remained as datasets rather than a unifying classification. This paper introduces the LRC (Lunar Regolith Classification) Framework and the Overconsolidation Ratio applied for the Moon (OCR*), the first contractor-ready system to organize Apollo-derived trends into excavation demand zones (L1–L5). LRC is explicitly a classification, not a stratigraphy: depth ranges are indicative and require in-situ verification before use. Each zone is defined by bulk density and strength ranges, field proxies (bootprints, trench stability, auger torque, seismic contrasts), and corresponding excavation implications. Worked examples from Apollo 15 (mare), Apollo 16 (highlands), and Apollo 17 (pyroclastics and talus) demonstrate how observed data translate into LRC zones. These cases show that LRC captures both systematic depth trends and sharp local heterogeneity. The framework standardizes excavation planning for landing pads, haul roads, berms, foundations, and tunneling trials, while converting floaters from hazards into resources. LRC thus provides a common language for lunar construction. Rooted in Apollo evidence but designed for Artemis verification, it is proposed as a living standard; a reference framework to guide site preparation, excavation, and risk management in the next phase of lunar development.

Feb 22, 2026

By J. Baz-Dresch

A custom-designed shotcrete system, consisting of an 8-m3 (10-yd3) transit mixer and a shotcrete spray boom carrier, is used bya 2-man crew to transport and place up to 25 m3 (32 yd3) of steel-fiber reinforced, dry, silica fume shotcrete per II-hour shift. Shotcrete is custom blended by a local supplier and delivered predampened. Mix design and quality control is performed with a computer program that develops and graphs a properly balanced mix based upon the materials sieve analyses.

Jan 1, 1991

By Sherwin F. Kelly

"THE TITLE I have chosen is certainly not one of those self-explanatory ones. I shall endeavour to make its significance clear during my remarks but, in the hope of minimizing that inevitable exodus which follows a good lunch such as this, I am going to withhold the final key to its meaning until the very last sentence of this talk.Some explanation is due at the beginning, however, so for those of you unfamiliar with Spanish I will explain that casa means house, or home. The casa about which I am going to talk necessitates a wide .and generous interpretation of the word, because I am using it to indicate principally that portion of the North American continent which is the home, in the western hemisphere, of British and American ideals of justice and freedom, the dignity of the individual and his right to exercise private initiative .and engage in private enterprise. In a wider sense, I am including the entire western hemisphere, which may yet stand as the last bulwark of political and industrial democracy.As for the treasures of which I am about to speak, may I remind you that there are no• material treasures but those derived from the earth, and they are derived by one of two processes, -mining and farming. These two fundamental industries are the basis, and the sole material basis, of our welfare, our wealth, our very existence. From farming, whether it be farming of the land. or farming of the sea, we obtain the food to keep us alive, healthy and able to work."

Jan 1, 1955

By R. L. Miller

"Why should we care about diesel quality amidst the complexity of mining for minerals? Mining companies use a large amount of diesel fuel in their worldwide operations, both for moving ore from the mine to the processing mills or transportation hubs, and to generate power for onsite processing. This creates a large carbon footprint and poses both environmental risk with the production of emissions, and public perception of how those companies do their business as stewards of the environment while incurring a huge fuel expenditure. To improve diesel quality and create incremental value and greater environmental stewardship, the opportunity is broken down into several segments: 1. Mining industry diesel consumption 2. Fuel quality issues 3. Impacts on operations, economics, and emissions 4. Potential solutions 5. How improved fuel quality saves fuel expenditures 6. Economics of improved fuel quality 7. Recommended testing process 8. Fuel quality analysis checklist MINING INDUSTRY DIESEL CONSUMPTION The average grade of mined Australian ore bodies has halved, while the waste removed to access the minerals has more than doubled over the last 30 years, thus increasing energy consumption by 70%, (http://eex.gov.au/industry-sectors/mining/). Energy consumption and intensity in mining and mineral processing is rising at around 6% per annum. The mining industry is a huge consumer of diesel fuel worldwide, and the SRS Rocco Report of 4 August 2014 gives a better picture of recent trends. To better understand the reasons to reduce both fuel costs and consumption, we need to compare metrics on the amount of diesel consumed per each ounce of gold produced over the last decade. The rate of diesel consumption in gallons per each ounce of gold produced for the top five worldwide gold producers has doubled in the last 8 years from 12.7 gallons per ounce in 2005 to 25.8 in 2013 as shown in Figure 1 below.This is caused by 1) lower ore grades requiring more hauls to get same amount of finished gold product, and 2) haul trucks moving ore from deeper sources in open pit and underground mines. For one large multi-national gold mining company, the 2005 waste rock / production ratio was 52 metric tons/gold ounce; by 2013 that ratio had grown to 113 metric tons/gold ounce per the same SRSrocco 4 August 2014 report. Using the metrics above, the top 5 gold miners used over 591 million gallons of diesel fuel in 2013. The cost of diesel in dollars per ounce of gold has increased from $30.48 in 2005 to $101.14 in 2013, an annual appreciation of 16.2% as shown in Figure 2 below."

Jan 1, 2017