Search Documents

By C. K. Leith

THE interdependence of nations in regard to mineral supplies has grown apace with the expanded needs of industry, with depletion of reserves, and with advances in technology. This increased mutual dependence raises many questions of foreign economic policy of special importance in our postwar planning. Realization of the urgent need for the development of a general mineral policy broadly based on national requirements led to discussions of the problem between officials of the Department of State and myself, as a result of which it was suggested that I make an informal and unofficial canvass of the views of mineral specialists of the country on foreign mineral policy.

Jan 1, 1946

By Slav Tchepak

The King's Wharf development is located in Sydney's Darling Harbour area. The site was originally used for industrial maritime purposes, which over the years has been reduced to accommodating leisure craft only. The site has been filled with various materials, resulting in fill materials varying from soils, to concrete and rock fill. A prestigious new residential development at the site required piles to found in Sydney sandstone that occurred at depths ranging from 1 to 27m. The selection of appropriate pile types is discussed, as are details relating to the design and construction of cast insitu Omega piles and CFA piles. A number of issues needed to be addressed relating to the piling, including the design of the piles, the potential for liquefaction of the fill material due to earthquakes, penetration of the piles through the fill materials, installation of the piles to a satisfactory positional tolerance and pile performance. A number of piles were dynamically tested to prove pile performance and these results are presented and compared with design expectations. The project was successfully completed on time and budget, indicating the selection of pile types in the difficult ground conditions to be appropriate.

Jan 1, 2000

By Ad. Breyre

For more than 20 years, Belgium, leading all the coal-mining countries, has made increasing use of sheathed explosives, which wore first suggested by the late E. Lemaire, predecessor of the author gas Director of the Institut National des Mines. It appears to the author that it will be valuable to show how the use of sheathed explosives has developed in Belgium, how the various difficulties encountered in their manufacture have been overcome gradually, and the tyros of sheathing that have survived and the reasons for their survival.

Jan 1, 1940

By Christophe Bragard, Rebecca Reeve

The Regional Connector Transit Corridor (RCTC) Project is a 1.9-mile-long metro light-rail extension project that traverses the historical core of downtown Los Angeles, California. This project aims to improve mobility throughout downtown LA with fewer transfers for riders. It is designed to connect two existing rail lines for a more seamless travel. The project consists of twin bore tunnels, three new stations, and is scheduled to be completed in 2022. The design-build contract was awarded to the Regional Connector Constructors (RCC) in 2014, a joint venture of Skanska and Traylor Bros, Inc. with Hatch Mott MacDonald as the designer. One of the challenging aspects of the project was the construction of a crossover cavern in a narrow public right-of-way surrounded by historical structures. RCC used Sequential Excavation Method (SEM) to construct the crossover cavern measuring 287 ft long by 58 ft wide by 36 ft tall. The initial lining of the cavern featured a 12 in. fiber reinforced shotcrete lining. The initial lining was separated from the final lining by a hydrocarbon resistant membrane, as specified by the standard requirements of Metro. The cavern features a cast-in-place final lining with a thickness of 5 ft 9 inches in the invert and 18 inches in the crown and walls. The structure also features a nonload bearing plenum slab and interior walls for ventilation.

Jun 13, 2021

By D W. Wall, J P. Vagenas

Questions of sampling precision and accuracy affect every process plant in differing ways and to differing extents. To address these perceived issues, chemists, metallurgists and engineers are often asked to check their results to confirm their reliability. However, it is not possible to achieve the level of detail required to check every sample, especially if the event has already occurred. No operation has the resources to frequently sample every point in the process for the purpose of verification.One way to address this scenario is by generating a sufficiently detailed comparative data set from a dynamic mass balance simulation of the processing plant. This mass balance uses both sample and plant instrument data to model every flow, while also taking inventory changes and process chemistry into account.The mass balance data can be used to identify any bias present in plant sampling and analysis. It can also be used to verify any unexpected assay results by taking a holistic view of the process. Improving the precision and accuracy of sampling data helps support operational decision-?making and understanding. It also improves the accuracy of the dynamic mass balance used in this process, facilitating further improvements.CITATION:Vagenas, J P and Wall, D W, 2017. The benefits of automated metallurgical accounting for plant sampling, in Proceedings Eighth World Conference on Sampling and Blending , pp 203–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Edward L. McHugh

The appraisal of mineral resources of the Challis National Forest, Idaho, by the U.S. Bureau of Mines, was made so that the mineral resources of the forest could be appropiately considered in land use planning. Information from this study is intended to tip the U.S. Forest Service to incorporate mineral resource data into forest plans The study was done in conjunction with the U.S. Geological Survey, which released a companion report on the geology and mineral potential of the Challis National Forest in 1989. This summary report is derived from a more detailed USBM Open-File Report (MLA 6-91) that includes descriptions of mines and prospects, commodity profiles, and development cost models. Since the 1860's mines within the Challis National Forest have produced mineral commodities worth more than $590 million at current (1989) commodity prices. Identified mineral resources have a gross value of about $2 billion at current prices, including 8 strategic or critical minerals. The U.S. Bureau of Mines study identified and described 723 active and inactive mineral properties within the forest. Mineral properties with identified resources were evaluate to determine their economic significance, and an assessment was made of the feasibility of mineral development. Of the 2,516,191 acres in the Challis National Forest, about 390,000 acres were classified as having mining development interest. Commercially important mineral production, mainly of molybdenum, gold, and silver from the Challis National Forest is likely for the foreseeable future.

Jan 1, 1991

By Robert L. Kranz

Mining-induced microseismicity data collected by the U.S. Bureau of Mines in a hard-rock mine were analyzed for spatial and temporal patterns that might prove useful for prediction of rock bursts or assessment of rock mass damage changes. Pattern attributes described and illustrated in the previous report (part 1) were applied to the study of aftershock sequences associated with two different stopes. The aftershock sequences were spatially and temporally fractal, and the fractality was maintained for up to 16 h following a sequence progenitor. This suggests mechanical interdependency among the after-shocks. No statistical difference was found in the distributions of fractal dimensions when comparing two different stopes or when comparing aftershock sequences initiated by blasts or bumps. This suggests a lack of sensitivity to both stress perturbation mechanism and local damage states. However, differences between the two stopes were found in other sequence attributes that support inferred differences in the magnitude of stress concentrations and damage near each stope, and over time as a stope is developed.

Jan 1, 2010

By Kwangmin Kim, Junnhyeok Park

In the hard-rock mining industry, the generation of fines during blasting is an important issue because it has a significant effect on production processes. Although various approaches have been used to estimate fines generation in recent decades, as a practical matter, measuring the amount of fines is nearly impossible given the technical limitations and the scale of mine blasts. In this study, a dynamic PPV damagemodel was developed and applied to predict fines generation as a result of blasting. This modified version of the crushed zone model (CZM) considers dynamic rock properties and peak particle velocity (PPV), which represents the induced stress in blasting. Dynamic rock-fracturing tests were conducted using a split Hopkinson pressure bar (SHPB) to determine the parameters that represent the relationships between rock strength and strain rate as well as the relationships between fines amount and strain rate in the model. A case study was conducted that entailed determining the radius of the crushed zone for given blast designs and rock properties and then measuring the fines amount within this crushed zone. This case study indicated that the dynamic PPV model can provide a rough estimate of fines generation for given dynamic rock properties and blast design parameters and that this method has the potential to be a useful indicator, or index, of fines generation.

May 16, 2020

By T. K. Mukherjee

The importance of the processing of secondary resources such as solid industrial wastes and liquid effuents as well as byroducts for the recovery of the associated metal values hardly needs any elaboration. Such processing contributes in no small measure.towards the augmentation of the availability and the supply position of resources. As an added benefit, it leads to a reduction in environmental pollution caused by the undesirable waste materials. As some typical examples of secondary resources in the Indian scenario, mention' can be made of spent catalysts, metal/alloy scrap, ash, consumed batteries, flue dust, slag, sludge and slime, pickling solutions, spent acids; plating rinse solutions, spent etchants, waste water from synthetic fibre manufacture and from tanneries etc. These wastes constitute a source of a variety of non ferrous metals. In the processing of secondary resources like these, the techniques of hydrometallurgy such as solvent extraction play a pivotal role. This paper outlines the efforts made to use solvent extraction to recover (1) base metals such as copper, zinc, nickel and cobalt from a number of secondary resources like cake, and sludge(2) refractory metals like molybdenum and vanadium from sulphidic, byproducts and spent catalyst and (3:) nuclear metal like uranium from phosphoric acid. In the case of base metals, process flowsheet involving the use of acidic extractants such as DEHPA and PC88A have been optimised. The problem of iron removal from the leach liquor, "which influences the metal recovery process significantly, has drawn a special emphasis. hi the case of refractory metals, basic extractants .like Alamine 336 has been pressed into service to produce kilogramme. quantities of pure salts of molybdenum and vanadium, Finally, the paper gives a brief account of plant experience in recovering uranium from phosphoric acid, using 'a solvent system comosed of DEHPA and TOPO.

Jan 1, 1996

By C. A. Herbert

Information Circular 6746 reviewed the fatalities in Indiana coal mines. for the fiscal year October 1, 1951 to September 30, 1933. Since then Indiana has changed its fiscal year to the period July 1 to June 30, but as most statistical data on accidents are arranged according to calendar years, the data in this paper are for the last 3 months of 1932 and the calendar year 1933, rather than for the new Indiana fiscal year. Tables 1 and 2 list the fatalities in Indiana coal mines3/ by cause and occupation for the last 3 months of 1932 and for the calendar year 1933. The fatalities for the small wagon mines employing fewer than 10 men are separated from those employing 10 or more men to call attention to the ex- tremely high fatality rate in small mines, largely because the State mining law does not apply to them nor do they come under the jurisdiction of the Indiana mine inspectors; as a result health and safety conditions are ex- tremely bad. During the last 3 months of 1932, 5 (approximately 42 percent of the total) fatalities occurred in the small mines, while for the calendar year 1933, 12 (approximately 32 percent) of the fatalities occurred in them. The Indiana Division of Mines and Kining estimates that these small mines have an annual production of approximately 325,000 tons, or about 4.5 percent of the total coal-mine production of the State. In other words, for these small mines the fatality rate per tons mined during 1933 was about 10 times as great as for the mines employing 10 or more men. Another lamentable feature in connection with the fatalities in small mines is that very few carry any compensation insurance and the owners are not worth enough financially for dependents of victims to collect anything under the common law; as a result, the dependents of those killed usually are left penniless and subjects of public charity.

Feb 1, 1935

By William Reisz

Managing the blast site at almost any operation can be a daunting task. There are so many details that must be observed, understood, and acted upon. It goes without saying that there are no two locations that have the exact same challenges and concerns. The level and the extent of these challenges can vary widely.

Jan 1, 2014

By James K. Gowans

The Red Dog Operation is located in northwestern Alaska at Latitude 68°, 100 miles north of the Arctic Circle and 50 miles inland from the Chukchi Sea. The orebody was acquired by the NANA Regional Corporation, (an Alaska Native Corporation established by the Alaska Native Claims Settlement Act of 1971), in 1980 in their land selection. In 1982 Cominco American and the NANA Corporation signed a development agreement and Cominco Alaska Inc., a wholly owned subsidiary of Cominco American, was formed to manage the Red Dog Project. An extensive exploration program in 1980 -1982 outlined a mineral inventory of 85 million tons, at a grade of 5.2% Pb, 17.1 % Zn, and 2.4 oz/ton Ag, which makes the Red Dog the second largest deposit ever discovered. Broken Hill, in Australia, is the only zinc orebody which was originally larger than Red Dog. The design of the facilities is to process 2.1 million tons of ore annually, which will produce 560,000 tons of zinc concentrate, 100,000 tons of lead concentrate and 50,000 tons of bulk lead/zinc concentrate.

Jan 1, 1991

By M Philip Schwarz

"This paper reviews the status of computational modelling of a variety of common metals reduction processes, namely the blast furnace, rotary kiln and fluidised bed, and one new process not yet commercialised, namely smelting-reduction as in the HIsmelt Process. In each case, the last decade has seen the emergence of the capability to simulate the processes using multi-phase reacting computational fluid dynamics techniques. In some cases this capability is still in the process of being developed, and the next few years will see the maturing of the modelling techniques. As they become established, it will be possible to apply them to further refine the older technologies such as blast furnaces and rotary kilns, and assist in the optimisation, commercialisation and acceptance of the newer technologies such as fluidised bed and molten bath reduction. The development of a computational fluid dynamic model of bath smelting-reduction is described in some detail to illustrate how a large number of complex and interacting phenomena can be successfully simulated within a CFD framework. IntroductionPyrometallurgical reduction processes, such as the iron blast furnace, have become increasing more sophisticated through the centuries, so that today they are often highly efficient. There are continuing pressures, however, to refine existing processes and develop new ones. The imperatives are often economic, given that the long-term trend in the price of metals is always downward. In recent times, there has been the additional need to improve the environmental impact of metal production. Given that they almost inevitably require the use of carbon, metal reduction processes are large sources of greenhouse gases, and even a relatively small improvement in efficiency can be valuable in reducing CO2 production. Local environmental issues, such as the need to control of particulate emissions, are also driving incremental improvements in equipment.In addition to the economic and environmental drivers mentioned above, new process development is also being driven by the need to process new ores, and the need to produce unrefined metal in a form more compatible with alternative routes for downstream processing. An example of the latter is the production of DR! (Direct Reduced Iron) as a feed for EAF Electric Arc Furnace) in mini-mills.Further improvement of processes that have already been honed by continual plant experimentation over many years is not an easy task. To deliver further gains in efficiency, throughput, or product quality requires a highly sophisticated tool: one such tool· is computational modelling."

Jan 1, 2001

By W. Curlook, V. G. Papangelakis, M. Baghalha

A pressure acid leaching process has been developed for the extraction of metal values, nickel, copper, cobalt and zinc, from base metal smelter slags. The basic concept contemplates cooling the smelter slags through solidification sufficiently slowly to induce a good measure of crystallization; and subsequently, after fine grinding, to pressure leach such slags at around 250°C while applying oxygen overpressure, utilizing smelter byproduct sulphuric acid. High levels of extraction of the slags' metal values are thereby achieved. It has been shown that if the same slags are quenched thereby producing an amorphous structure, the resulting metal extractions are very low. The process is applicable to smelting furnace throwaway/discard/dump slags, as well as to in-process converter slags. By extracting the bulk of the residual base metal values in the throwaway/discard/dump slags, the resulting leached residues are rendered virtually benign vis-à-vis the external environment.

Jan 1, 2004

By N. A. Barcza

DC plasma-arc technology using a hollow graphite electrode (cathode) has been successfully implemented in the primary metallurgical industry in South Africa up to the 30 MW scale. Mintek has applied its expertise base, established over the past fifteen years, to testing the treatment of metallurgical wastes such as carbon- and stainless-steel plant dusts, lead- and zinc-containing slags, and residues from the base-metal industry. Favourable results have been achieved, and disposable products were produced. The evaluation of numerous wastes indicates that recovery of zinc as metal gives the best economic return from these sources. Direct recovery via a splash condenser or electrolytic zinc extraction from fume are the two preferred alternatives under review. In both instances dehalogenation is an important issue, but can be achieved by suitable treatment processes. The Enviroplas technology provides a flexible, commercially viable approach to the treatment of a wide variety of wastes. Mintek, together with its associate Pyromet CC, are installing a plasma- arc pilot-plant facility with both an ISP lead-splash condenser of about 5 t/d condensed zinc capacity and a combustion chamber to burn zinc vapour to zinc oxide. This will demonstrate the suitability of the Enviroplas technology for treating specific metallurgical wastes, so that customized industrial plants can be engineered based on large-scale testwork.

Jan 1, 1994

By Claus G. Goetzel

POWDER metallurgy is known as the art of producing metal powders and fabricating them in a nonfusion process by a simultaneous or consecutive application of pressure and heat under controlled operating conditions. Before the advent of powder metallurgy, the high melting points of the refractory metals and nonmetals made their manufacture and use practically impossible. Today, however, the uses of refractory materials in high-speed cutting tools, surgical instruments, brake linings, electrical contact switches, and filaments in incandescent lamps are commonplace in industry. Lately designers have even been turning to powder metallurgists to develop new techniques of fabricating refractory materials for extreme-service use in high-temperature zones of such modern products as gas turbines and jet engines. The new techniques being born will undoubtedly provide industry with a great number of new alloys and materials for future designing.

Jan 1, 1948

By L. B. Pankratz

Thermodynamic data on the elements, oxides, sulfides, halides, and selected hydrides, carbides, nitrides, carbonates, sulfates, silicates, and miscellaneous compounds were reviewed, evaluated, and compiled at the Bureau of Mines. Values for CP°, S°, H° -H°298, ?Hf°, and ?Gf° are given in tabular form. A brief thermodynamic background and a number of examples and applications are presented.

Jan 1, 1984

By Emil H. Geus

A process has been developed to recover aluminum from dross which does not require the use of salt flux as commonly employed, This results in a salt-free residue which has potential industrial uses or alternatively can be safely land-filled. The dross is first heated by an air-fuel or oxy-fuel burner in a sealable rotary furnace. At a suitable temperature the burner is turned off and the temperature of the dross thereafter controlled by means of an atmosphere of oxidative and inert gases. When the free metal has agglomerated it is first discharged from the furnace, followed by the residues.

Jan 1, 1995

By B. A. McKee, T. Adamcewicz

For a capital expenditure of only $46,000, Caland Ore Company has successfully converted its three dry grinding center peripheral discharge rod mills to dry grinding ball mills. The conversion has resulted in a significant capacity increase, operating cost reductions and in-plant environmental improvements. This paper describes why and how• the conversion was made.

Jan 1, 1972

By V. O. Tenorio, P. P. V. Coronado

"INTRODUCTION Productivity in Open Pit mines depend on the observation and adjustment of critical phases of operation. As one of the most expensive activities in Open Pit production, optimization of the load-haul-dump cycle becomes a critical aspect to address. Using simulation techniques and an ad-hoc methodology for analyzing the Key Performance Indicators (KPIs) involved in the production cycle, it is possible compare actual performance and ideal operating conditions and develop an alert system when operating conditions are sub-par with the expected production standards. STUDY OBJECTIVES The purpose of this work is to implement a methodology for optimizing the haulage cycle by identifying and adjusting the factors that affect the cycle time performance. The methodology includes the implementation of an alert system emitting warning messages when one or several trucks are idle or the time of completing production tasks is falling outside a predefined value. This alert is compared with pre-defined Key Performance Indicators (KPIs) and determine corrective actions: • Demonstrate the benefits of time analysis and how this affects the productivity results in the mining process; • Demonstrate the utility of KPIs in the extraction of ore and waste, and how they help to identify equipment performance; • Develop software interfaces to visualize the Alert System in order to increase awareness in the operations supervisor; and • Make recommendations for future applications that can help improve the productive process of an Open Pit mine. PROBLEM STATEMENT Transporting material in Open Pit mines may require the utilization of high capacity equipment, which also represents an elevated cost per hour. A supervisory system that controls the adequate distribution of trucks and shovels by providing the operational status of each unit shall contribute to increase productivity and subsequently reducing operational costs. Nevertheless, there is an issue with certain dead times such as queue trucks for loading, trucks waiting to be loaded, and other delays. This creates inefficiencies in fuel consumption and energy utilization. For the identification of delays, a context-based system could be required in order to help optimizing the haulage cycle time by controlling delays in loading, haulage, and dumping. After applying this methodology, efforts were focused in correcting out-of-standard performance values."

Jan 1, 2016