Search Documents

By Naoki Hiroyoshi, Hajime Miki, Tsuyoshi Hirajima, Masami Tsunekawa

Acidic solutions for chalcopyrite leaching contain cupric, ferrous and ferric ions, and the oxidizing power of the solutions is indicated by a redox potential, determined by the concentration ratio of ferric to ferrous ions. This paper reviews our previous studies on the redox potential dependence of chalcopyrite leaching in sulfuric acid solutions. Leaching and anodic-polarization experiments showed that coexistence of cupric and ferrous ions activate anodic dissolution of chalcopyrite, causing faster copper extraction at the potentials below a certain value (critical potential). The analysis of the AC impedance spectra for chalcopyrite electrode indicated that a high-resistance passive layer grows on the chalcopyrite surface without cupric and/or ferrous ions, and that coexistence of these ions causes a formation of another product layer and inhibits the passive layer growth at low potentials. These results are explained by a reaction model assuming the formation of intermediate Cu2S due to chalcopyrite reduction and the subsequent oxidation of the Cu2S. The critical potential corresponds to the redox potential of the Cu2S formation and the predicted values matched with the experimental results. Catalytic effect of silver ions on chalcopyrite leaching was also discussed based on experimental results and the above model.

Jan 1, 2003

By L. H. Michaud

An existing mining company plans to extend their surface coal mining operations in central Pennsylvania. Although the proposed site contains pyritic material, the results of the acid-base accounting for the site show an overall NP:MPA ratio of 4.26:1 for the entire site. The pyritic material is, however, associated with the lower of the three seams to? be mined. If traditional dragline mining methods were used, this would result in the acidic material being placed at the top of the spoil piles, exposing it to air and water, and therefore to the formation of Acid Mine Drainage (AMD). Further concerns are associated with the fact that the alkaline material is not distributed evenly over the mine site. In order to prevent the formation of AMD, the company has proposed to mine the area using Truck/Shovel mining methods. This technique offers a more flexible alternative for cut sequencing and for the selective placement of waste material. Working with the Department of Mineral Engineering at The Pennsylvania State University, a mine plan was developed for this site. This plan results in the layering of the alkaline and acidic spoil in order to achieve an overall net alkalinity in all spoil areas. Mining of this site should therefore not result in the formation of AMD.

Jan 1, 1994

By Dean G. Heitt

"The Rain and SMZ mines from 1987 to 1994 produced a total of22.0 t of gold from a pre-mine reserve of 14.24 Mt of ore grading 2.13 g/t Au.Gold at Rain is hosted within the basal portion of the Mississippian Webb Formation. ·Mineralization is closely tied to the Rain Fault which is interpreted to be the main feeder for the deposit. Multiple collapse and hydrothermal breccia events provided permeability for the mineralizing fluids in the otherwise unreactive siltstones. Major alteration events include: decalcification and dolomitization of the Devils Gate Limestone; and silicification, baritization, argillization and oxidation of the Webb Fm. Six ore types based on XRD and visual rock chip Jogging have been identified: siliceous ore containing >40% quartz and <30% barite; siliceous-baritic ore containing mostly silica but >30% barite; baritic ore containing >40% barite; argillaceous ore containing >40% total clays (including alunite); calcareous ore containing mostly calcite and dolomite; and carbonaceous ore which has significant pyrite and organic carbon. Metallurgical testing of the oxide leach grade ores found that recoveries, on -1.3 cm crushed material, were greater than 70%. Results also found that Rain ore has strong grind dependency due to silica encapsulation.The Rain leach pad was commissioned in 1988, and to date 9.3·Mt at an average grade of0.65 g/t Au have been placed. Life to date recovery, through December 1995, is approximately 51 %, for a total of3.87 t of gold produced. Two major factors have contributed to the low leach recoveries at Rain when compared with the metallurgical testing: 1) More argillaceous ore than expected was placed on the pad especially late in the mine life and 2) approximately 50% of the tons placed were run-of-mine with no agglomeration."

Jan 1, 1997

By E. A. Mevissen

With the ever increasing consumption of mineral commodities, the vital question is not whether sufficient mineral quantities will be available, but rather can the known existing low grade resources be mined economically. Conventional conveyor systems are being used in some open pit mines to decrease haulage costs. n an effort, to take this concept one stop further, this contract study examines the use of a high angle conveying system in an open pit mine. It identifies available high angle conveying equipment and examines the haulage and crushing costs associated with both a conventional truck and shovel mining operation and a high angle conveyor operation. These costs analyses were performed on a hypothetical copper, taconite and phosphate mine. Information was gathered from a series of high angle conveying equipment and open pit mining operations in the U.S. Volume I includes a detailed review of the state-of-the-art in high angle conveying concepts, the, hypothetical mine development, and the cost analyses. Volume II includes the appendices.

Jan 1, 1981

By R. Nyirenda, B. Besa, N. Dzimunya

The accurate estimation of peak particle velocity (PPV) is crucial during the design of bench blasting operations in open pit mines, since the vibrations caused by blasting can significantly affect the integrity of nearby buildings and other structures. Conventional models used to predict blast-induced vibrations are not capable of capturing nonlinear relationships between the different blasting-related parameters. Soft computing techniques, i.e., techniques that are founded on the principles of artificial intelligence, effectively model these complexities. In this paper, we use the random forest (RF) algorithm to develop a model to predict blast-induced ground vibrations from bench blasting using 48 data records. The model was trained and tested using WEKA datamining software. To build this model, a feature selection process using several combinations of Attribute Evaluators and Search Methods under the WEKA Select Attributes tab was performed. The correlation coefficient of the actual data and RF model-predicted data was 0.95, and the weighted average of the relative absolute error (RAE) was 10.9%. The RF model performance was also compared to the equivalent-path-based (EPB) equation on the testing data-set, and it was seen that the RF model can effectively be used to predict PPV. The study also demonstrates that the EPB equation is a suitable empirical method for predicting PPV.

Mar 30, 2023

By Dominic Parmantier, Jason Page

"In the past, the designers of DSM have analyzed various failure modes and then specified a minimum unconfined compressive strength (UCS) for the soil-cement. The specified minimum UCS reflected the compressive stress in the soil-cement under design loads and an appropriate factor of safety. With the increased use of finite element analysis for the design of DSM applications where allowable strain as well as stress are considered, there is a growing trend for designers to specify a modulus and occasionally a tensile strength for the soil-cement in addition to the UCS. This paper compares the relationship of modulus and tensile strength to UCS for soil-cement from a recent DSM project with unique testing requirements. These results are compared to published data. The case is made that designers should utilize published relationships to characterize the required strength and stiffness by a single acceptance criterion: UCS.INTRODUCTIONAs the use of DSM has increased in popularity so has the use of service state deformation analysis in lieu of more traditional failure mode analysis. Most DSM designers are interested in the appropriate modulus values and occasionally tensile strength values of soil-cement as well as simply the unconfined compressive strength (UCS) of soil-cement.Although there are numerous published correlations between the UCS, tensile strength and modulus of soil-cement, some DSM project specifications are produced which have acceptance values for tensile strength, modulus, and UCS. If this specification of multiple strength properties is consistent with the nature of soil-cement, then there is really no harm except for the expenditure of client money on unnecessary testing. If however the multiple strength properties specified are inconsistent with the material properties of soil-cement, then the specifications can create the expectation that the DSM contractor can somehow create a custom soil-cement with tensile strengths and modulus characteristics which are unachievable.This paper presents a brief summary of a project in Burnaby, B.C. which specified minimum values for the tensile strength, modulus, and UCS of the soil-cement. A comparison of those test results to published correlations between the UCS and the tensile strength is presented. Additionally, a comparison of modulus derived from two different methods of testing is presented along with a comparison to published correlations between UCS and modulus for soil-cement."

Jan 1, 2015

By George J. Simchuk

The selection of a stripping method and subsequently, the stripping equipment, are two of the most important decisions confronting a project engineering staff during the initial feasibility study of a new coal stripping operation. The selected stripping units average from 60 to 70 percent of the total capital outlay for mine equipment and their selection will affect the type, size, and quantity of the attendant equipment, such as loading shovels, drills, haulage trucks, and bulldozers. This paper is intended to report on an in depth study by Utah&apos;s Technical Services Staff regarding the selection of stripping equipment for the Goonyella Coal Mine in Queensland, Australia. We will touch briefly, on the objectives considered in this selection; the various alternatives which were explored; the general assumptions that were followed throughout the engineering and design of an appropriate stripping system; and computations necessary to determine the amount and size of stripping equipment. INITIAL EXPLORATION Utah Development Company (presently 90% owned by Utah Construction & Mining Co. and 10% by Australian investors) commenced systematic geological studies of the Bowen Basin coal fields of Central Queensland in 1961. The Blackwater Mine as shown in Figure 1 has since been established in this area and is now producing 3.0 million tons per annum of washed coking coal. Geological reconnaissance was then extended to the northern part of the Bowen Basin and in 1963 Utah&apos;s coal prospecting area covered 2444 square miles of Central Queensland. The authority to prospect north of Blackwater has since been trimmed to 810 square miles by relinquishments to the State.

Jan 1, 1971

By R. L. Sebastian

ALUMINUM&apos;S war history is the record of a successful race to expand facilities fast enough to meet the multiple increases in military requirements, principally for aircraft. From the beginning of the war program in 1940 through 1942, requirements estimates were repeatedly lifted to new high levels, and plans for increasing capacity had to be constantly revised. In 1943, basic metal supply caught up with and exceeded requirements, and by 1944, the surplus of primary production was large enough to force reduction in output and plant closings. In the past two years, ingot capacity has been ample, though periodic critical shortages have been experienced for a few fabricated shapes as a result of sudden shifts in demand. And now with all controls lifted we are faced with surplus capacity, surplus stocks, and surplus scrap. In 1938 the Aluminum Co. of America was the only U. S. producer of primary

Jan 1, 1946

By Brianna M. Eiter, Jennica L. Bellanca

Mineworkers face a challenging and dynamic work environment every workday. To maintain a safe workplace, mineworkers must be able to recognize worksite hazards while they perform their jobs. Though hazard recognition is a critical skill, recent research from the National Institute for Occupational Safety and Health (NIOSH) indicates that mineworkers fail to identify a significant number of hazards. To further the understanding of mineworkers’ hazard recognition ability and to begin to address hazard recognition performance, NIOSH researchers analyzed data collected during a laboratory research study to determine the effect of individual mineworker factors including risk attitude, work experience, and safety training on hazard recognition accuracy. The results of this study show that mineworker risk attitude and safety-specific work experience affect hazard recognition performance while hazard-specific safety training does not. These results suggest that some of these individual factors can be overcome through experience and training. Potential strategies that can be used to address these factors are also discussed.

Aug 31, 2020

By AIME AIME

The first session, held Tuesday evening, February 23, in North Sheffield Hall, was called to order by Louis V. Pirsson, Chairman of the Local Committee, who introduced Prof. Russell H. Chittenden, Dean of the Sheffield Scientific School of Yale University. Professor Chittenden, in behalf of the Governing Board, felicitated the Institute on its visit to New Haven, and cordially welcomed the members and guests to the University and the city. Dr. James Douglas, who presided at the meeting, responded in behalf of the Institute. The Secretary announced that, upon the proposal of many members, the unanimous report of the Committee on Membership, and .the unanimous recommendation of the Council, the following members had been unanimously elected by the Board of Directors Honorary Members in the American Institute of Mining Engineers Prof. Richard Beck, of Freiberg, Saxony, in recognition of his distinguished service to technical literature, and the cordial

Apr 1, 1909

By A. B. Hooker, L. C. IlsLey

"Field inspections and data relative to the use of rubber-sheathed trailing cables in mines show that much cable is ruined or its probable life shortened by being overheated in service.The length of cable required to make connection from a source of supply to a machine at the face workings may be 100 to 500 feet. As a rule, the cable is carried on a reel and unreeled as required; and thus in most cases soma of the cable is not removed from the reel. The overheating generally occurs in that part of the cable which is left on the reel.Factors that determine the heating of trailing cables are:1. The size of the conductors in the cable.2. The maximum energy to be supplied through the cable, based upon the horsepower of the motor and the degree to which the motor is loaded.3. The voltage of the supply and the variation of the voltage at the receiving end.4. The time length of current flow and whether continuous or intermittent.5. The kind of current (direct or alternating).6. The amount of ca· le left or the reel.7. The type of cable used.8. The kind of reel used.In connecti0n with an investigation of the general performance of rubber-sheathed trailing callas, the Bureau of Mines has made a limited study of some of these factors, including the following points:"

Jul 1, 1931

By J. A. López-Molina, S. García, V. Castellanos-Pedroza

"Grouting aims to reduce the permeability of rock mass below a predetermined value and has been widely used in rock engineering field for a long time. However, the injection procedure needs several empirical decision makings and it is rather difficult to reliably confirm the achievement of improvement, because the grout penetration process is not sufficiently clarified. This investigation proposes a neuronal method of defining spatial distribution of rock hydraulic properties and a fuzzy scheme for estimating their relation with the grout penetration (consumption, localization and filling material). The intelligent method stands as a tool for helping in harmonizing the sealing activities and the medium conditions. The virtual simulation of grouting strategies embraces geology, hydraulic and rock characteristics and the filling process. Important aspects as different pressure injection levels and fracturing systems can be holistically studied using the intelligent environment, resulting in an advantageous, economic, flexible and interactive tool for planning better this critical activity.INTRODUCTION Grouting is a very common method of sealing rock and repairing concrete structures (Butron et al., 2010) and its use in engineering of dam-foundation and tunneling has been documented as very successful (Yang, 2004). Generally speaking, to achieve the closing purpose, boreholes are drilled into the rock mass and grout is injected (under pre-selected pressure) until the fractures around the borehole are filled. The complete filling of these fractures is possible if they are connected to each other in such a way that the remaining water and air can be displaced outside the designed grouting zone (Houlsby, 1990; Kutzner, 1996). Water testing is necessary for evaluating seepage potential and for determining whether grouting is necessary or practical. Regardless of the main reason for the investigations, design of a program for water testing for grouting should consider the type of structure to be built, the geologic conditions at the site and the level of seepage control desired. As information gathered the report must content the fracture openness, number and connectivity, exploratory drill holes orientations, materials situation and a panorama of rock-mass state (quality)."

Jan 1, 2015

By J. C. Edwards, C. C. Hwang

A computational fluid dynamics (CFD) program was applied to fire spread along combustibles in a ventilated mine entry. The rate of flame spread was evaluated for the ribs and roof of a coal mine entry; timber sets; and a conveyor belt. The CFD program models char forming materials with temperature dependent thermal properties. The program solves three dimensional time dependent flow equations with a mixture fraction model for the gas phase reactions. Radiant heat exchange is evaluated for non-scattering gas. The CFD program predicted a flame spread rate of 0.0145 m / s for an actual coal mine fire in which the estimated flame spread rate was 0.0086 m / s. This overestimated flame spread rate was a possible consequence of the presence of inert materials in the mine entry’s roof and ribs. CFD fire spread rate predictions of 0.043 m / s and 0.73 m / s bounded the measured value of 0.27 m / s for fire spread along Douglas Fir timber sets in a tunnel.

Jan 1, 2006

By A. F. Ogg

The installed world steel capacity remains 20% above the present world steel demand. Energy costs have risen enormously in recent years, as illustrated in Figures 1 and 2. The role of the sinter plant is becoming more exacting as it becomes vital to minimize energy consumption. Continuous grate sintering, although pioneered in the United States, has always been the second grade burden preparation route, due to the predominance of easily up- graded ores which were more readily agglomerated by pelletizing. To achieve blast furnace performance up to best world standards, sinter of consistent high quality must be produced with virtually no atmospheric pollution. The plants must be capable of achieving this demanding level of quality whilst utilizing high proportions of revert materials, iron ore concentrates and fluxes . However, with the present difficult economic climate in the iron and steel industry, the economic production of sinter and ultimately steel is becoming increasingly important. The iron and steel industry is looking closely at costs and is identifying the need for sinter plants that will cope with a wide range of sintering materials to give the cheapest blend at varying output levels dependent upon demand. In order to meet these requirements, sinter plant builders are designing plants with particular attention on flexibility.

Jan 1, 1980

The objective of the paper is to develop a material balance calculation procedure for a production unit involving two plants separated by a pipeline. The case study is taken from the oil sands industry. The raw sands are first mixed with water in a conditioning plant, then transported through a pipeline to an oil extraction plant. The combination of pipeline dimensions and nominal throughput creates a significant variable time lag between the two plants. As usual, mass balance calculations required for the evaluation of plant performance indicators, such as bitumen recovery, are inaccurate due to measurement errors. In addition, in the present case study, the time lag of the pipe creates an additional source of uncertainty, which may lead to misinterpretations and wrong decisions. Raw data are usually reconciled through steady-state mass balancing, to correct for measurement errors. However, because of the significant pipeline dynamic lag, standard steady-state daily mass balance may fail at giving an appropriate picture of the operations. The proposed solution to the data reconciliation problem includes the use of a pipeline plug-flow model in the mass balance calculation. To fulfil the industrial constraint that current data reconciliation must not modify past reconciled values, while still satisfying dynamic constraints, a daily one-step method, i.e. a unitary filter-ing horizon, is recommended. The method is illustrated with simulation data, and the results com-pared to those of standard data reconciliation methods.

Jan 1, 2014

By Mavor S.

Further discussion at the Mining Institute of Scotland's general meeting held in Edinburgh, 12 February 1916, with D.W. Mowat, president, in the chair, of a paper published in Trans. Inst. Min. Engrs., 1915, vol. L, p.625 and discussed vol. L, pp.92, 433, 468, and 704 included comments by Mowat D.W. and the author's reply

Dec 1, 1916

By Louis Frost

"A FIRE which forced the sealing -of the east side of Dominion No. 16 Colliery in the Town of New Waterford, Nova Scotia, occurred on October 6th, 1952 (Figure 1).So far as can be ascertained, the fire was first noticed in the roof of No. 7 East Lateral, after a brushing shot had been fired in the pavement. There appears to .be no doubt that this shot •blew out, igniting a small feeder in the roof.Regular air measurements and air samples, taken over a long period prior to the fire, indicated that the ventilation was adequate, for at no time had the percentage of CH4 in the general air current exceeded one per cent in this location. The last regular monthly samples and air measurements, taken at the end of September, showed the condition of the ventilation to be:Return at the Top of No. 8 East WallQuantity .... 27,700 cu. ft. per min.CH4 .......................... 0.32 per centC02 ................................ 0.10 per centHowever, in the week preceding the fire the mine examiner on four occasions had reported small feeders of gas at the face of the brushing in No. 7 East Lateral.Figure 2 is a diagram of the working place where the shots were fired. The face brushing had been shot down at 3 :45 p.m. and cleaned up. Two 'hurdle screens' had also been erected, one close to the face brushing and the other fifteen feet from the face."

Jan 1, 1953

By Gobbs C., J. Lam

"The Eagle East project, accessed from the existing and operating Eagle Mine in the Upper Peninsula of Michigan, is an underground base metal project currently in execution by Lundin. This paper will provide an update on several aspects of ventilation including use of a twin-decline access, innovative airflow crossover arrangement and construction ventilation methodology. Integration into existing mine ventilation systems including construction methodology will also be covered. Performance benchmarks and lessons learned are discussed across these topics.INTRODUCTIONLundin has owned and operated the Eagle Mine since 2013. This hard rock underground mine is located in the upper peninsula of Michigan, USA. High-grade nickel ore is mined using sublevel open stoping mining methods and trucked to surface via haul ramp. The mine, having been in production for four years, is nearing the completion of the initial orebody. A satellite orebody 2,000 meters East of the current workings and approximately 900 meters below surface, was identified that could extend operations until 2023. In 2016, Lundin approved the Eagle East project and construction began in 2017 (Lundin Mining Corporation, 2017).Due to proximity to the existing mine, Eagle East will be both accessed and serviced from the existing Eagle Mine. Ventilation at the Eagle Mine uses two fresh air intakes with direct fired combustion heaters; one at the mine portal feeding fresh air into the ramp and one at a fresh air raise located near the Eagle deposit. The primary ventilation circuit is powered on the exhaust air side, with two 700 hp exhaust fans located at a single return air raise. Underground, fresh air is distributed through the main access decline and fresh air raise (FAR) to the production levels and controlled with mechanical regulators on the exhaust side. The exhaust air is collected through return air raises with a collector/transfer drift on 250 Level and then to the surface through a return air raise (RAR)."

Jan 1, 2019

By R. D. White

"The Cumberland Basin of Nova Scotia has long been considered a structural basin by virtue of the elliptical outcrop and inward dip pattern of the Pennsylvanian outcrops. Recent published and unpublished data indicate that subsidence began in the late Devonian, perhaps resulting from a graben or rift. The Mississippian sediments which filled the growing depression were continental, lacustrine and marine with evaporites. The cessation of the riftforming processes is recorded by the alluvial swamp-type sediments of the Pennsylvanian which filled the depression. In excess of 25,000 feet of Carboniferous rocks are believed to be present in the deepest part of the Basin. Starting with the rift hypothesis, we can speculate on the kinds of sediments, their location and the structural features present beneath the Pennsylvanian surface. Using surface exposures and a limited amount of subsurface data, we theorize that (1) the Mississippian evaporites acted as glide zones which effectively divided the Basin into two horizontal structural layers. The rocks above the evaporites, responding to Appalachian stresses, formed the long diapiric folds with cores of overthickened evaporites. Below the evaporites the structures are related to movements of the rift floor, compaction closures and structures formed by differential horizontal movements of the rift walls. (2) The rift, in its deeper parts, will have more and a greater variety of marine rocks than the outcrops indicate. Should the rift hypothesis be correct, the possibility of finding hydrocarbons is enhanced."

Jan 1, 1972

By David J. Blackwell

The challenge; to design production facilities and in particular separation equipment which have the ability to deal effectively with the ever changing composition of well fluids, over the life time of the field in which it is operating, ensuring maximum uptime of the asset coupled with consistently effective separation. Design engineers are, however, continually confronted with a dilemma when selecting materials of construction for Oil/Gas separation equipment, since they are generally obliged to select an acceptable material of construction, based on ?predicted? operating conditions, at the lowest acceptable cost. Consequently many designs are somewhat basic and do not take into account the constantly varying dynamics of the well fluids being released into the separator. As oil fields mature, oil companies endeavour to maximize revenue by maintaining oil and gas throughputs. This often results in an associated increase in water and sand volumes and, in order to maintain efficient separation, an increase in operational temperature and pressure; subjecting the equipment to operational conditions for which it was never designed. In reality, therefore, the limitations and constraints placed upon new construction design often result in Maintenance Engineers having to solve the ensuing problems in difficult ?in-field? environments. Should refurbishment or upgrade be required then the status of the platform and that of the vessel during shutdown will dictate how this is achieved. Hotwork on the vessel is generally not preferred due to the requirement for post weld heat treatment and re-classification of the pressure vessel, not to mention the added risk in terms of safety. Unfortunately, until recently, there have been few alternatives to conventional ?hotwork? repair and protection systems, especially since the performance of cold curing polymer based repair and coating systems, for use in oil and gas process equipment, has, until recently, been limited by their resistance to temperature and pressure in immersed conditions. In line with the continued development of high temperature / high pressure oil and gas fields however, recent breakthroughs in polymer technology can now offer both repair and protection solutions which are able to function effectively at temperatures up to 180°C in immersed conditions combined with resistance to the destructive forces of explosive decompression from pressures in excess of 90 bar. This paper will look at recent work that has been undertaken to determine the suitability of modern polymer based repair and protection systems as an alternative to hotwork; thus enabling newly designed and upgraded internals to be cold bonded into position and further protected with temperature resistant coatings, in order to minimize the downtime of the asset and further to protect the vessel internals from the Erosive Corrosive environment.

Jan 1, 2006