Search Documents

By Robert W. Van Dolah

The prevention of fires and explosions involving the combustibles and oxidants likely to be found in flight vehicles requires a knowledge of the flammability and related characteristics of these materials. This circular is a compilation of the available charactersilics data for a series of combustibles and oxidants of current interest. Vapor pressure data are presented for fluorine, oxygen, chlorine trifluoride, nitrogen tetroxide, nitric acid, hydrogen peroxide, ethylene oxide, hydrogen, ammonia, pentaborane, unsymmetrical dimethylhydrazine, monomethylhydrazine, hydrazine, and a series of hydro-carbons including decalin, tetralin, bicyclohexyl and other high-density fuels. In addition, flammability characteristics diagrams are included for each of the fuels in contact with air and, where available, other oxidants (for example, oxygen and nitrogen tetroxide). To assist in understanding these data, sections on definitions and theory and applications have been included. Each section is complete in itself and can be used separately. For example, a reader who is familiar with the general theory of combustion and detonation may find the data sections more useful than the definitions and theory and the application sections. However, since pertinent data are included in these sections, they should also prove useful to the experienced engineer interested in preventing fires and explosions.

Jan 1, 1963

By B J. Wight, R Mackay, S Kim

Improving the understanding of the processes governing ground movements in and around brown coal open cuts is of significant interest for both operating stability and rehabilitation. Brown coal, lignite, is a low-rank coal that is best described as a soft rock, with geotechnical characteristics that derive from its organic origin. It is well-known that low-rank coals exhibit creep behaviour; however, little has been reported on the impacts of chemical processes on brown coal creep behaviour even though organic substances are susceptible to chemical alterations and mining processes will contribute to changes to the geochemical environment; around most mines, groundwater flow patterns are altered leading to enhanced surface water infiltration. Here we study the deformation behaviour of brown coal in response to ion exchange reaction. Our experimental results show that for different ion exchange conditions different characteristics of secondary compression are observed. With the addition of Ca2+, the ratio between coefficients of secondary and primary compression (Ca /Cc) initially decreased, presenting a minimum value at the concentration of 0.005?M, then increased significantly. This implies the importance of ion exchange process for the long-term deformation of brown coal. On the other hand, increasing Na+ concentration did not affect Ca /Cc values significantly over all tested concentrations. The suppression of diffuse double layer was still observed for Na+-treated samples as increasing Na+ concentration decreases Ca values. From a practical perspective, this study did not consider the tertiary creep behaviour and eventual creep failure.CITATION:Kim, S, Mackay, R and Wight, B J, 2014. Creep due to chemical alteration of rocks – a case study in brown coal, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 61–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

The Ernest Henry Mine is an open pit copper-gold mining operation located in north-west Queensland, Australia. It is owned and operated by Xstrata Copper with a current concentrator throughput of approximately ten million tonnes per annum. The pit will cease mining towards the end of 2010. Extensive surface diamond drilling has confirmed an extension of the orebody to depths of 1000 m below surface. A prefeasibility study was commissioned in late 2006 to investigate underground mining options with the preferred mining method being an inclined sublevel cave. In February 2008 mining of a decline commenced in conjunction with a feasibility study to further investigate the project. Work from the prefeasibility study indicates that an underground crusher, conveyor and hoisting shaft could be utilised to crush and transport broken ore from the sublevel cave workings to the concentrator. The study suggests that a production rate of five million tonnes per annum could be achieved and sustained for up to ten years. Ventilation designs and requirements will form a large section of the feasibility study. This paper will detail investigations of preliminary ventilation network designs of the proposed sublevel cave. Work has been completed using both Ventsim and VumA ventilation simulation packages. Ventsim was used to provide preliminary estimations and suggest alternatives for: surface fan duties;airflow characteristics (direction, velocity, pressure and quantity); andventilation network design in key mine areas. With mining activities reaching depths in excess of 1000 m below surface an analysis of heat conditions should be conducted. The VumA software package was used to model the thermal properties of the ventilation system. This model will provide a basis for the preliminary decisions on refrigeration requirements for the mine.

Jan 1, 2008

By J. L. Jambor, H. W. Nesbitt

Oxidative dissolution of pyrrhotite and pyrite is largely responsible for the sulfate-rich waters of the vadose zone in the Waite Amulet tailings. Although the shallowest of the sulfate-rich waters are of the Fe-SO4 type, they change to Mg-SO4-type, near-neutral waters within 1-2 m of the tailings surface. Phyllosilicates and amphiboles are the only minerals present in sufficient quantity to ameliorate the amount of acidity produced. X-ray diffraction and microscopic studies of bulk sample indicate that quartz, chlorite, talc, amphiboles, magnetite, albite, and micas are the major and minor non-sulfide minerals, but their variations with depth do not give clear indications of depletion in the vadose zone. Mineralogical and bulk chemical compositions of the tailings confirm that Fe2O 3 has accumulated in large quantity in the vadose zone, with the Fe having been derived from Fe sulfides. When the effect of Fe2O3 is accounted for, the bulk compositions suggest that SiO2 is slightly more abundant in the vadose zone than in the saturated zone. This may be the result of residual enrichment of siliceous minerals such as quartz and albite in the vadose zone. Weathering of the tailings since the cessation of deposition in 1962 has resulted in a well-defined zone of sulfide depletion and secondary sulfate-mineral development. Although some silicate dissolution is indicated by pore-water compositions, the role of silicates in providing neutralization seems to have been minimal. The contribution by silicate minerals in laboratory tests of neutralization potential may be excessive relative to that in natural settings.

Jan 1, 1999

By H. G. Wickes

Virtually all fluorine consumed by the aluminum industry is as the electrolyte of the Hall-Heroult process for producing primary aluminum. A small amount of fluorspar is used but most fluorine is consumed as either aluminum fluoride or cryolite. Some fluorine- containing materials are used in secondary aluminum production, but the amount is negligible compared with primary production requirements. Any analysis of the future of the primary aluminum industry must take into account two powerful and closely related driving forces which are shaping that future. These factors are increasingly stringent restrictions on the emission of pollutants and the continuing cost-price squeeze. Nowhere do these factors combine more forcefully than in the area of fluorine consumption. We can safely assume that industry efforts to reduce fluorine consumption will be intensified and that these efforts will be fruitful. This paper will attempt to identify and quantify the factors and trends of fluorine consumption during the next decade. We will be concerned primarily with the demand for new fluorine. Sources of new fluorine will not be treated.

Jan 1, 1973

By Jochen Petersen

This paper gives an overview of the various strands of postgraduate and undergraduate training offered in the Department of Chemical Engineering at UCT. Since 2003 the Department is offering a formal postgraduate MSc programme in hydrometallurgical engineering aimed especially at graduate work-based engineers, with 5 weeks of intensive course work plus a research dissertation on a work-related project. This programme has now run 5 times over the years and produced some 20 degrees. The paper reflects on the experiences with running the course, especially the difficulties experienced with supervising industry-based external students. Furthermore, through the Department a graduate training program is offered for all junior metallurgists at a major South African minerals company. This 2-year program, which is currently on its 12th cohort, offers 1 or 2 week intensive blocks of course work alternating with longer stints where the candidates are based at various operations. Although primarily focussed on minerals processing, it has a significant element of hydrometallurgy in it and in recent years an advanced hydrometallurgy stream has been introduced. The paper reflects on the development of the program over the years, the benefits it has provided to the company as well as some of the challenges that remain. Finally the paper gives an overview of hydrometallurgy related undergraduate and research-only postgraduate MSc and PhD projects at the university. Some emphasis is placed on the recently launched South African Minerals and Metals Research Initiative (SAMMRI), a joint government-industry programme to support university-based research in the area of applied metallurgy.

Jan 1, 2014

By Mackenzie Burnett

This program was initiated by USBM to quantify the respirable dust problem caused by the use .of roadheaders in underground metal/nonmetal mines with special emphasis on this problem in uranium mines. The contract called for the development of methods or equipment to alleviate the respirable dust and to implement the solution in a mine. Attempts to quantify the dust problem were made in the following way: survey of MSHA records, survey of state mine enforcement agencies, survey of mine records, dust measurements taken at two mines using roadheaders. The results of this study are not conclusive due to very limited and sometimes less than useful data; however, the study does indicate that a serious dust problem could and may exist. If and when roadheader use becomes more popular, it is almost certain that development of dust control procedures and equipment will be necessary. This contract was concluded without developing this equipment since only one roadheader is currently in use in an American uranium mine and the mine prefers not to participate in the program at this time. This report discusses the available data concerning respirable dust problems and presents a solution which can potentially help to solve the problem. The solution requires the use of blowing ventilation, on-board dust extraction at the source, and filtration, as well as continued use of water sprays. The on-site tuning of such a system is necessary to demonstrate the degree of improvement possible.

Jan 1, 1981

By Charles T. Holland

The tonnage produced on mechanized automated retreating longwall faces in the United States is growing rapidly. This time last year some 14 faces were operating, and in addition to that, three were known to be down looking towards revision or repairs before being placed back in service. These, it is believed, are now in service. It is estimated at the present time, therefore, that somewhere between 20 and 25 faces are being operated in the country. A survey made last year by the School of Mines, West Virginia University, indicated that longwall mining in general has been beset with a great many problems, some more serious than others. The problems that we propose to discuss here are those pertaining to roof and floor trouble in the tailgates. Longwalls are operating in this country at the present time under an overburden ranging from 200 feet to nearly 3000 feet. Main and tailgate entries are operating in panels of up to five each, with the width of the pillars between these entries varying from 20 to 50 feet. Face lengths are running from 270 feet to 670; actually a face 800 feet long should be possible. The most economical face is often spoken of as being around 450 feet.

Jan 1, 1969

By Robert C. Dyni

The use of techniques and equipment designed to pneumatically place backfill into an underground mine opening through boreholes for subsidence abatement has historically met with limited success, largely due to the inability to directly monitor the placement of the backfill in the opening. The success of a backfilling project cannot be guaranteed if it is not known whether the underground opening has been completely filled with backfill material. To overcome the inability to directly monitor backfill placement, the U.S. Bureau of Mines developed a pneumatic backfilling system that allows for direct viewing of the backfill as it is placed in an underground mine opening. This system utilizes a recently developed pneumatic nozzle coupled with an instrumentation package that allows for real-time observations and measurements of backfill placed in an underground opening through a borehole. The nozzle utilizes a high-velocity airstream to redirect backfill falling through a pipe in the borehole and directly in front of the nozzle; the airstream redirects and propels the backfill horizontally into the .mine opening at over 100 ft/s. The instrumentation package, mounted directly to the nozzle, contains a video camera, high-intensity lamps, laser-rangefinder, electronic compass, and water sensor.

Jan 1, 2010

By J. D. Corbett

The spatial coincidence of the seven anomalies is obvious, even though the self-potential is offset northward. Because the ratio, as an indicator of conductivity, is a relative estimate at best, concise interpretation is limited in almost every instance to the location of a conductor or conductor axis. When related to the initial phase of an exploration program, magnitudes and ratios similar to those obtained from any one of the methods described, would be sufficiently attractive to warrant further investigation. The compilation shown is an empirical comparison of actual field results and no emphasis has intentionally been placed on the relative merits of one method in respect to another. Too many additional factors, i.e., size, depth and conductivity of overburden, etc., that cannot unequivocally be answered, enter into such a comparison before a relative evaluation can be made.

Jan 1, 1961

By Noriaki Kurita, Norihiko Fulcatsu, Teruo Ohashi

"An electrochemical sensing device for hydrogen in molten metal has now been available owing to the development of the proton conducting solid electrolyte made of ceramics of metal oxide. The structure of the sensor and the theoretical limitations of its applications are discussed based on the electrochemical properties of the electrolyte used. The practical performance of the sensor is reviewed from the results of test measurements at the plants of aluminum and copper melting industries. The effectiveness of the sensor to the process control of continuous casting of copper is also discussed.IntroductionSince the in-line monitoring of the amount of oxygen dissolved in molten metal was realized by using the oxygen concentration cell based on zirconia solid electrolyte a similar method has been expected to be developed for sensing of hydrogen, which is a very important element of gas species in liquid metals, especially, in aluminum and copper. In 1981; Iwahara and coworkers found the dominant proton conduction at a high temperature in some perovskite-type oxide (1). Since then, the effort has been made to apply this proton conducting material as the electrolyte of the hydrogen concentration cell for high temperature use. The hydrogen sensor for liquid aluminum of this kind was first produced in 1991 (2) and released commercially from TYK Co., Ltd. Recently, we have developed the mother one usable at higher temperature such as copper and silver melting processes (3). In this note we discuss their structure, design and applicable limitations based on the electrochemical properties of this new type electrolyte. The performance of the sensor and benefit to use it to control the melting process is also discussed"

Jan 1, 2000

By C. C. Clark, D. J. Benton, J. B. Seymour, L. A. Martin

"The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics and alternatives, based on information from injury reports, legacy research, stakeholder input and published literature. The results indicate that jackleg drills are involved in more groundfall accidents in underground metal mines than any other drill, and jackleg-drill-related injuries are most prevalent at the face in the course of installing initial ground support. Practical mechanized alternatives to jackleg drills for drilling and bolting under incomplete support in narrow underground openings have not yet been realized. Small, versatile mechanized bolting equipment needs to be developed to address jackleg-drill-related accidents and improve safety at mines where jackleg drills are being used. IntroductionJackleg drill is a generic name for a handheld, rotary, percussion rock drill equipped with an attached reaction leg to provide stability and thrust (Fig. 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jackleg drills are classified according to the bore size of their pneumatic pistons, which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in.) (Kurt, 1982; Clark, 2012). Jackleg drills typically weigh 46.7 kg (103 lb), but the weight can approach 54.4 kg (120 lb) after being fitted for operation with drill steel and air and water hoses (McKibbin and Clark, 2001). In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in.) diameter holes up to 1.83 m (6 ft) deep in rock."

Aug 1, 2016

By J. V. W. REYNDERS

IN THE remarks which I am about to make concern¬ing the safety work of the Bureau of Mines, I want first of all to disengage myself from a disposition, which is frequently in evidence, to give spectacular emphasis to the hazards of mining operations. It is of the' utmost importance to the industrial welfare of our country that the enormous annual requirement of fuel be produced and be made available in our economic activities, with a minimum of distress and hardship. The safety of coal mining is a condition with which. we are all concerned in a fundamental way. And yet we should not rush to accept hastily conceived notions that laxity among employers in respect to safety measures exists to any outstanding degree. In fact in a large number of instances, the precautionary efforts of min¬ing companies, directed to the elimination of accidents are beyond all criticism, albeit the industry suffers in reputation from the carelessness of, its less effi¬cient constituents. The Bureau of Mines has been a leading influence in disseminating the doctrines of safety, in securing the cooperation of the miners themselves, and in stirring up ' the laggards, both among the employers and the employed. It is much to the interest of well-conducted mine operations that the industry, as a whole, observe safety regulations to the utmost.

Jan 1, 1925

By R. D. Clarke, E. De Souza

"A framework for ventilation planning, with a focus on planning to the end-of-mine life, was developed for the Diavik Diamond Mine, Northwest Territories. This framework was successfully used by Diavik’s mine engineers to select a cost-effective ventilation plan that met the life-of-mine requirements. The framework achieved this result by reconciling the production plan with the ventilation plan. A set of design acceptability criteria was created and a PICK (possible, implement, challenge, kill) chart was used to quickly narrow down the generated ideas for detailed assessment and economic analysis. RÉSUMÉ Un cadre de planification de l’aérage, qui met notamment l’accent sur la planification jusqu’à la fin de vie de la mine, a été développé pour la mine de diamants Diavik. Les ingénieurs miniers de Diavik ont su mettre à profit ce cadre pour sélectionner un plan d’aérage rentable qui répondait aux exigences propres à la durée de vie de la mine. C’est en conciliant le plan de production et le plan d’aérage que cet objectif a pu être atteint. Un ensemble de critères d’acceptabilité de la conception a été créé et un tableau PICK (de l’anglais possible, implement, challenge, kill, une méthode donnant la priorité à certaines actions proposées ou à des idées visant à résoudre des problèmes) a été utilisé pour rapidement limiter les idées générées et les soumettre à une évaluation et une analyse économique détaillées.INTRODUCTION The Diavik Diamond Mine, Northwest Territories, has been an underground-only operation since 2012 and has a remaining mine life of 8 years. In the first year of underground-only operations, the production rate increased from 60 kt of ore per month to more than 160 kt of ore per month. In subsequent years, this rate was continuously increased (Table 1) because the operation went through various improvement initiatives. By the end of 2016, Diavik’s total production was 0.41 Mt (+22.8%) ahead of the 2012 budget for 2016 production."

Jan 1, 2018

The Elgas Underground Storage Facility at Port Botany, Sydney, is the first purpose-built cavern of its kind in Australia and allows large capacity, safe and environmentally benign storage of Liquefied Petroleum Gas (LPG). The facility provides Elgas with the flexibility to source product at competitive prices and will ensure long-term security of supply. Construction has provided Orica Australia, formerly ICI Explosives, with a unique opportunity to provide a bulk explosive delivery system specifically designed to meet the exacting demands of the site (see Figure 1) and of the project.

Jan 1, 1999

By Andrew J. Neale, Chelvan Veloo

P.T. Freeport Indonesia currently operate a 600,000 t/d mining and 125,000 t/d milling operation in the remote highlands of Irian Jaya, Indonesia. The isolated location and generally difficult working conditions make for challenges not encountered in most North American operations. In spite of this, the mill technical groups have been able to develop and maintain a highly effective level of plant wide automation. This has been achieved through the appropriate selection of available technologies and the implementation of innovative management practices. This paper provides an overview of the control systems currently installed and focuses on those practices which have resulted in the long term success of process control at Freeport.

Jan 1, 1997

By Ginger L. Hustrulid

Conveyor belts are a critical component in tunneling projects. This paper reviews current design considerations for conveyor belts. Rubber compounding differences to meet local fire resistance regulations or certain cover characteristics such as higher abrasion resistance or low carbon footprint rubbers for applications are reviewed. Evaluation of fabric belts, steel cable belts and the benefits of each carcass design for a particular use is also examined to help with proper carcass selection to decrease downtime from unexpected failures. Finally, this paper takes a look at some of the differences when working in metric versus imperial units.

Dec 1, 2022

By M I. Pownceby, S Bhargava, F Charalambous, S McMaster, R Ram, J Tardio

"A key component of any geometallurgical investigation involves being able to predict element or mineral recoveries from simplified input data such as bulk chemistry and/or mineralogy. This relies on the metallurgist having access to accurate information regarding the chemistry of the ore and gangue minerals as well as the likely impact on processing/extraction caused by the impurities (present either as gangue or as substitutional impurities). In this study the chemical properties of two commercially important uranium minerals, brannerite (U4+Ti2O6), and uraninite (U4+O2), were characterised using X-ray diffraction (XRD), scanning electron microscopy (SEM), and electron probe microanalysis (EPMA). Significant levels of impurities were present in both samples with the uranium minerals deviating significantly from their ideal chemical formulae. Differences in chemistry were due to: cationic substitution decay of the uranium isotopes into radiogenic lead and other daughter products mixed uranium oxidation states post-depositional alteration.As well, the brannerite sample showed evidence of significant radiation-induced metamictisation. Leach tests to measure the ease of extraction of uranium from both samples were conducted over a wide range of conditions (temperature, acid concentration and oxidant concentration). For uraninite, the lower U dissolution rates observed in the natural sample compared to a synthetic UO2 sample were directly attributed to the presence of impurities. For brannerite, significant metamictisation of the natural sample led to enhanced U extraction rates compared to a heat treated fully crystalline sample. This study highlights the importance of detailed mineralogical characterisation studies in any uranium process mineralogy investigation as the compositional, textural and microstructural aspects of the main uranium phases present will likely play an important role in any process to extract uranium.CITATION:Ram, R, Charalambous, F, McMaster, S, Pownceby, M I, Tardio, J and Bhargava, S, 2013. Chemical and microstructural characterisation studies on naturally occurring uranium minerals - implications for processing, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 325-334 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By C. M. Bartley

Fluorspar, in addition to its familiar uses as a metallurgical flux and as a source of the electrolyte for aluminum production, has become important as an essential raw material in the rapidly growing fluorine chemical industry. The unique ability of fluorine to react and form compounds with al-most all other chemicals has made it one of the important elements in modern chemistry. Research and development over the past thirty years have resulted in a current annual production of fluorine chemicals that is both technically and economically important to industry. Because many of these chemicals and products are relatively new, and most have properties that are not duplicated by other materials, the present uses are expanding rapidly and new applications are being reported continually. Fluorspar, the only immediate and practical source of fluorine, is therefore an important mineral. This fact has been recognized in major industrial areas such as the United States and Western Europe, but has received little attention in Canada.

Jan 1, 1962

By Paul Pugsley

The EMSpec sensor employs the principle of measuring the complex impedance of the target steel over a range of frequencies these impedance values in turn varies with transformation fraction of the steel. A full scale implementation of the Real Time Transformation Monitoring has been installed at a quality large European steel producer to show the benefits of such a system. A total of three EMSpec sensor heads have been installed between the exit Finishing Mill and the Down Coiler on a HSM. For the successful production of Dual Phase, TRIP and TWIP steels increased control of the cooling regime is demanded; the use of surface temperature measurements alone cannot guarantee to achieve the desired mechanical properties. The EMSpec sensor, which is engineered to withstand this harsh environment, in real time directly measures the percentage transformation of the steel in the cooling area, typically in the accelerated water cooling zone. Using the information from the sensors integrated into the mill model enhances the models ability to predict the transformation profile.

Aug 17, 2017