Search Documents

By W. E. Wells

This report describes experimental investigations made in the batchwise retorting of Colorado oil shale. Three heat-carrying mediums were used -hot shale gas, superheated steam, and hot flue gas. Using hot Shale gas for retorting, the several variables studied were retort-inlet-gas temperature, gas velocity through the shale bed, shale particle size, and grade of shale. In studying the effect of any one of these variables on oil yield, as and operability, the other variables were maintained essentially constant. Oil yields decreased with increasing in-let-gas temperature and increasing shale-particle size, and oil yield increased with increasing grade of Shale up to 50 gallons of oil per ton of shale, beyond which the process was inoperable because of swelling and caking of the shale during retorting. Changes in gas velocity had little effect on oil yield. Gas yield increased with increasing inlet-gas temperature, gas velocity, particle size, and shale grade. Oil yields of 100 percent of Fischer assay and from 1,600 to 1,800 cubic feet of 300-B.t.u. gas per ton of shale were obtained. Two runs only were made using superheated steam. Oil yields averaged 97 percent of Fischer assay, and gas yields averaged 4,00o cubic feet per ton of shale. Retorting with a hot flue gas produced from combustion in the shale bed, as in the N-T-U process, gave excellent yields using closely sized shale with recycling of flue gas. An excess of fine shale in the charge resulted in channeling and low oil yields. Using no recycle gas, good yields were obtained that tended to decrease with increasing air rate, and the retorting rate increased with increasing air rate over the range studied. Coking was not found serious with 30-gallon shale at the air rates used.

Jan 1, 1952

By T. J. Ballard

"INTRODUCTION The Buck. Creek corundum area of Clay County, North Carolina, includes one of the largest single masses of peridotite outcrops in the whole Appalachian Range and has been described by Pratt, an early authority on corundum, as offering one of the best potentialities for corundum production in North Carolina.Two principal types of corundum deposits are found at Buck Creek the vein type and the corundum-bearing amphibolite dikes.The vein deposits occur in structural fissures that strike north to northeast in a gangue of feldspar, zoisite, an, chlorite. The corundum is generally coarse-grained and good-quality. The corundum content varies from several percent to 50 percent.The corundum in the amphibolites is more or less disseminated through the dike, is generally lower-grade, and is less in quantity, than the vein corundum. About 50 percent of the amphibolite corundum is coarse enough for snagging-wheel grade but is difficult to separate from the amphibolite.Production from the Buck Creek area has been small and came mainly from high-grade pocket in the vein deposits. Pratt 3/ reports 300 tons of corundum ore was produced to about 1896. No record of subsequent production is available.The critical shortage of corundum during the war, due to transportation difficulties and the depletion of deposits abroad, prompted the Bureau of Mines to investigate domestic reserves.After a favorable report was obtained on the Buck Creek area, the Bureau began exploration of the deposit in September 1943 and continued until February 1945."

Apr 1, 1947

By E. Dendy Sloan

An overview of hydrate properties is given, with emphasis on unusual deviations from ice, the most common solid water form. Reliable sample preparation and reproduction of in situ hydrates provide the foundation for all hydrate science and engineering. Relations are given to connect the three domains in the title: (1) micro-scopic properties measured with Raman, NMR, and diffraction spectroscopy, (2) meso-scopic properties measured with single crystals, and (3) macro-scopic properties measured with pressures, temperatures, volumes, etc. A principal illustration relates micro-scopic and macro-scopic domains. Experiments provides the basis for improving statistical thermodynamics model for these compounds. To date, this model is one of the most commonly used industrial statistical thermodynamics applications, based upon the classical model of van der Waals and Platteeuw (1959). Microscopic measurements and simulations indicate model assumption improvements, resulting in the next generation of the statistical thermodynamics for improved macroscopic property prediction.

Jan 1, 2002

MIM Holdings Limited (MIM) committed to a long-term future in copper in the Carpentaria Mineral Province in 1996 with the development of the Enterprise and Ernest Henry mines, and an upgrade of MIMsÆ copper smelter in Mount Isa, and copper refinery in Townsville. The upgrade of the copper smelter will enable the smelter to produce 250 000 tpa of copper with a single primary smelting unit, the copper Isasmelt furnace installed in 1992. The copper Isasmelt furnace currently smelts concentrate containing 145 000 tpa copper. To reduce the risk associated with the copper smelter upgrade, and shorten the ramp up time of the upgraded smelter, two high-rate trials were undertaken in 1997 to demonstrate that the copper Isasmelt furnace could, with an additional 525 tpd of tonnage oxygen, treat concentrates containing 250 000 tpa copper. During the trials the concentrate feed rate to the Isasmelt furnace was increased from its average rate of 100 tph of concentrate to 150 tph of concentrate. The increase in the capacity of the furnace was achieved by: supplementing the installed tonnage oxygen capacity of 595 tpd with an additional 300 tpd supply; reducing variability in the furnace feed rate from ¦25 per cent to less than ¦5 per cent; and reducing tramp air. The Isasmelt furnace smelted concentrate at a rate of 140 to 150 tph for four hours 25 minutes during Trial 1, and at a rate of 150 tph of concentrate for five hours and 30 minutes during Trial 2. The oxygen utilisation was 100 per cent during the trials with the process remaining under control. As a result of the development work for the trials the average treatment rate of the furnace under normal conditions increased by ten per cent.

Jan 1, 1998

By J. J. Gusek

The Riley Pass strip mine is an abandoned uranium-bearing lignite deposit in Harding County, South Dakota, covering about 150 acres of highwalls, pit floor and mine spoils exhibiting elevated levels of radioactivity. Six reclamation design alternatives were developed, ranging from doing nothing to reclaiming to approximate original con-tour. The alternatives were evaluated for expense, site stabilization, and mitigation of public safety hazards. A comparative economic evaluation on three of the alternatives was completed for the Forest Service in selecting an alternative and substantiating federal funding requests. This evaluation included economic impacts associated with physical and radiologic health hazards, affects on recreational users, socioeconomic impacts and environmental improvement.

Jan 1, 1995

By F. Kassabji

This publication presents the main experimental and theoretical results on the recovery of aluminum scrap (dross and Used Beverage Can) without use of any addition of fluxing salts. Dross and UBC's processing experiments have been conducted in a rotary plasma furnace operating in the transferred and non-transferred mode, using different plasma gases. The investigation involved the treatment of more than 100 kg of dross and other aluminum residues using plasma torches with less than 100 kW power. The experimental work showed that this process is .far more economical and kind to the environment than the conventional route using a salt flux. An equilibrium thermodynamic calculation at elevated temperature makes possible the prediction of by-products at various temperatures for different plasma gases.

Jan 1, 1994

By Luis v. Coppa

Since its inception in 1910, the Bureau of Mines has been the principal Federal agency involved in ore reserve estimations, using such traditional methods as polygons of influence and variations of inverse distance weighting While adequate for estimating the average are grades in a mining block or section, these methods do mot, however, provide a consistent way of quantifying the reliability of the estimates. This report describes a technique for enhancing ore reserve estimations using geostatistics, the methodology of which combines the spatial and random aspects of geologic phenomena into a formal theoretical framework for deriving the estimation variance of ore reserves. Correctly used, geostatistics enables confidence intervals to be placed around ore reserve estimates calculated from drill hole data. A geostatistical software system was obtained -From the U.S. Geological Survey and installed, aster slight modifications, on the Bureau's Wang computer. System testing and validation was conducted using a simple cast-book-type example. This was then followed by variogram analysis, point kriging and block kriging of data from a previously worked section of a uranium mine.

Jan 1, 1984

By H. B. Brunot

On April 26, 1949, the Bureau first approved a machine designed to replace the cycle of cutting, blasting, and loading coal by a single operation. This machine took the coal directly from the solid face and delivered it to transportation equipment. By January 1, 1955, 30 approvals for designs of machines of this type had been granted by the Bureau. In the main, this paper describes briefly the action of the various designs approved as permissible. In addition, the approval number, the date of approval, the voltage of the power supply, the number and character of the explosion-proof accessory parts, the size of the trailing cable, and the overcurrent protection at the outby end of the trailing cable are given for each design. Since no similar information has been published by the Bureau, it is hoped the material in this paper will be valuable in giving the mining public an organized look at the various machines of this nature that have been approved as permissible by the Bureau.

Jan 1, 1956

By John H. Smith

Because of increased pressure from Federal & State Regulatory Agencies, most acid flows will require some sort of treatment prior to being discharged to receiving streams. In many industries, the volumes of liquors are large and their acid content varied. Pressure to minimize costs of waste treatment equipment and land usage makes development of a treatment process incorporating these desires mandatory. "Standard" methods of acid neutralization with lime have been known for years, however, the volume and characteristics of the resultant precipitated solids can create a disposal problem. Also, when standard lime treatment is used, the settling characteristic of the precipitated solids is normally slow. In some instances, the necessity of added dissolved solids removal, (such as iron, needing aeration) add to the problem of concentrating neutralized solids. In a paper published in the September 1970 issue of "Coal Age," *the results of extensive test work by personnel of the Homer Research Laboratories of Bethlehem Steel Corporation, Bethlehem Pa., were reported. This paper dealt specifically with development of a flow sheet to treat acid mine drainage (hereafter referred to as AMD) from coal mine operations. Regulations on discharged water required basic pH and low dissolved iron content after treatment. Liquid flows of over 9 MGD from

Jan 1, 1972

By Raymond F. Moran

The history and development of the FMC Coke process has been reported in numerous presentations over the past 10 years (1, 2, 3, 4, 5, 6) but a short review is desirable, especially regarding the aspects that are influenced by the coal to be used. F'MC has been developing this process in pilot facilities since 1956 and in a modest sized plant in Kemmerer, Wyoming since 1960 (Figure I). This plant produces strong uniformly sized coke briquettes from a completely non-coking coal, namely Elkol, a sub-bituminous coal of the Adaville seam. Since operating commercially, over 300,000 tons have been produced, 90% of which has been used in electric phosphorus furnaces and some 10% of which went for trials in iron blast furnaces. We believe that this commercial use of non-coking coals is a unique experience in the history of coke manufacture.

Jan 1, 1975

By J. -M. Bosgiraud, G. Armand, S. Dewonck, L. Richard-Panot

"The Meuse/Haute-Marne Underground Research Laboratory (URL) is located on the eastern boundary of the Paris Basin. The URL started to be built in 2000 (shaft sinking operations) in the framework of ANDRA’s (French national radioactive waste management agency) research program aimed at determining the feasibility of a reversible deep geological disposal of high-level and intermediate-level long-lived radioactive waste (HLW, IL-LLW). Its underground drifts are used to study the Callovo- Oxfordian claystone layer between 420 m and 550 m in depth.The ongoing research program (started in 2006) following the “Technology Readiness Level” (TRL) Scale is more dedicated to technologies improvement and demonstration issue of the different disposal components, even if characterization and monitoring studies are still ongoing.In rock mechanics, at the main level of the URL (located at 490 m), construction and evolution of disposal cells of different size are studied for HLW and IL-LLW packages. A step by step approach, started in 2006, is carried out based on comparison of HM behavior of parallel drifts excavated/supported by different construction methods. These various configurations give insight of the influence of construction method on the EDZ extent and evolution and on the progressive loading of the support, which are key issues to design the Cigéo disposal drifts and excavations.The concept of disposal cells studied for HLW consists in horizontal steel lined micro-tunnels 80 m long and 70 cm in diameter. Several campaigns of tests have been carried out since 2009 in order to demonstrate the feasibility of excavating such micro-tunnels and study their behavior under different conditions (with and without back filling the annular gap between the rock and the casing, watertight or not casing). A full scale demonstrator representative of the benchmark concept has also been excavated, to study its behaviour under thermal loading with heat produced by electrical heaters."

Jan 1, 2015

By Normand Champigny

The Forces of Change ? The current business environment ? What can we expect for the future on management of physical assets ? The impact of maintenance on production costs ? What is RCM is doing is improving business performance ? The beginnings of RCM The RCM II Process ? RCM II is a structured process that involves employees in determining the best failure management tactics for systems and equipment in their operating context ? The method is an effective approach to risk and cost reduction as well as failure management

May 1, 2002

By C. C. Bailie

This paper will be concerned with those mineable coal measures at depths necessitating deep mine operations in the range of 200 feet to 800 feet in depth. The area is generally classified as the Southern Illinois Field but more specifically includes that part of the state south of a line extending from St. Louis, Missouri on the west to Vincennes, Indiana, on the east. This embraces an area which presently includes a total of 38 shipping mines and 5 local or truck mines. Of these shipping mines, 22 are deep (shaft or slope) mines and the remaining 16 are strips. The average annual production of the shipping mines is around 29 million tons. The presently classified mineable reserves of the area are estimated at around 70 billion tons.

Jan 1, 1964

By Arthur Notman

DESPITE the tremendous drop in the volume of domestic production of metals, their prices, and profits, the world as a whole has managed to produce and consume nearly as much as in 1937. Measured by production, 1937 was the record year for copper, lead, and zinc. The Copper Institute figures for 1938 (estimating December as equal to November) show that although apparent domestic consumption declined 309,422 tons, foreign consumption increased 133.035 tons. The total for 1938 was 1,971,790 tons compared with 2,148,177 tons for 1937. The domestic decline was 38.5 per cent, the foreign increase 9.9 per cent, and the total decline 8.2 per cent.

Jan 1, 1939

By Gary L. Hundley

The Bureau of Mines has devised and demonstrated a process for recovering Ni and Co from low-grade domestic laterites. The process consists of four major steps: (1) reduction roast, (2) ammoniacal leach, (3) solvent extraction, and (4) electrowinning. Several solid-liquid separation steps are required that affect the economics of the overall pro-cess. In this study, two techniques for solid-liquid separation, centrifugation and thickening, were investigated. This report presents the results of (1) laboratory and pilot plant studies to determine parameters for sizing centrifuges and thickeners and (2) an economic study of the two techniques, based on the requirements of a commercial-size (5,OOO-tpd) laterite processing plant. Sizing and other equipment-related recommendations, based on data from the Bureau's studies, were obtained from commercial manufacturers. The costs of thickening and centrifugation, including all the unit operations affected, were determined by the Bureau's process evaluation group. The total operating costs ~or separation using the two techniques (including depreciation on the capital cost of equipment) were found to be quite close: $17.26 per ton of laterite for centrifugation and $18.15 per ton of laterite for thickening. For centrifugal separation, the greatest cost was found to be the initial capital cost for the separation equipment; using thickeners, the greatest cost was for re-agent recovery.

Jan 1, 1984

By D. Harrington

The mining industry of the United States has-long been severely criticized because of its high rate of accident occurrence, net only as compared with other major industries-in the United States but also with the mining industries of other countries particularly Europe. Statistics (often not of strictly comparable nature) indicate that the accident-frequency rate in all mining is currently about three times and the accident-severity rate is about seven times as great as the average for general industrial work in the United States. These figures are by no means comforting to humanitarian mining men, irrespective of their status in. the industry, and they constitute a challenge that certainly cannot continue to be ignored much longer. This picture becomes much darker when the above statistics are augmented with data indicating that. on an exposure basis our mines (more particularly our coal mines) have accident rates two, three, or even more times as great as more or less similar types of mines in Europe, particularly England and Wales, Belgium, France, and Germany. However, these foreign accident statistics should be carefully analyzed before we become very mush concerned about them, because they are clot strictly comparable owing to several considerations, not the least of which is the fact that foreign methods of compiling or recording accident statistics often differ materially from ours. Moreover, foreign mining and other conditions axe definitely dissimilar to ours in many if not most phases, and numerous ether factors affect the comparability of foreign mine-accident statistics with ours. Unquestionably it should also be taken into consideration that the accident rate of the 130,000,000 or more constituting the populace of the United. States as a whole is much higher than that of any other major country in the world and is two, throe, or more times the rate of the European countries that have more favorable mine-accident rates than those of the United States. Moreover, it is significant that the mine-accident-severity- rate of British mines is about six times the average accident-severity rate of the major industries of the British Isles, or but little mere, favorable than the comparable figures in the United States, namely, that mining-has an accident-severity rate about seven times that of the average of about 30 of the major industries of this country.

Jan 1, 1941

By L. F. Willmott

The Bureau of Nines at Morgantown, W. Va., has been investigating, on a pilot plant scale, various methods of gasifying bituminous coal with oxygen and superheated steam to produce synthesis gas, as part of the broader program of finding new uses for coal. Differences in the pressure gasification methods used have depended on differences in the manner in which the pulverized coal is fed to the gasifier. One of the methods of feeding the coal that was investigated was the continuous, integrated coal-water slurry system. Goal and water were first mixed to produce a slurry; then the slurry was pumped through a heated coil. to evaporate the water fraction; the resulting steam was superheated, and some of it was separated so as to adjust the ratio of the residual steam to the coal fraction and make the resulting mixture suitable for partial combustion with oxygen in a pressure gasifier. Both before and during this reported3 developmental work it was necessary to make an extensive literature search into the technology of aqueous slurries in order to establish design criteria for the pilot plant and to correlate results of various phases of the work with that of other investigators, The pilot work coincided with the commercial development of a long-distance pipe- line for the transportation of coal as a coal-water slurry, and this fact tended to broaden the scope of the pilot plant work and the extent of the literature search. This bibliography is the compilation of the material that was collected.

Jan 1, 1963

By L. F. Willmott

The Bureau of Mines at Morgantown, W. Va., has been investigating, on a pilot plant scale, various methods of gasifying bituminous coal with oxygen and superheated steam to produce synthesis gas, as part of the broader program of finding new uses for coal. Differences in the pressure gasification methods used have depended on differences in the manner in which the pulverized coal is fed to the gasifier. One of the methods of feeding the coal that was investigated was the continuous, integrated coal-water slurry system. Goal and water were first mixed to produce a slurry; then the slurry was pumped through a heated coil. to evaporate the water fraction; the resulting steam was superheated, and some of it was separated so as to adjust the ratio of the residual steam to the coal fraction and make the resulting mixture suitable for partial combustion with oxygen in a pressure gasifier. Both before and during this reported3 developmental work it was necessary to make an extensive literature search into the technology of aqueous slurries in order to establish design criteria for the pilot plant and to correlate results of various phases of the work with that of other investigators, The pilot work coincided with the commercial development of a long-distance pipeline for the transportation of coal as a coal-water slurry, and this fact tended to broaden the scope of the pilot plant work and the extent of the literature search. This bibliography is the compilation of the material that was collected.

Jan 1, 1963

By J. L. Holman

In conjunction with its research program on separation, recovery, and recycling of metal, mineral, and energy-based materials in urban refuse, the U.S. Bureau of Mines is developing means to reuse and recycle plastics discarded in raw municipal waste. Experimental work on plastic waste from a community collection has produced some guidelines for systematic methods of processing, including air classification, cleaning, separation, and use or disposal. Sink-float methods are a practical means of separation into types. Methods for final disposition of the plastic waste include refabrication, thermal decomposition, and incineration.

Jan 1, 1972

By Saul J. Escalera

Mechanisms involved in the depression of the sulfides: pyrite, chalcopyrite, galena and sphalerite with potassium permanganate have been investigated. Flotation tests were conducted using potassium amyl xanthate, Z-6, and pine oil in the absence and presence of potassium permanganate at around pH = 6. 5 naturally yielded by the sulfides in the pulp. On the basis of crystal chemistry considerations, the amount of xanthate adsorbed by the sulfides depends on the amount of sulfur and metal ions present on the surface; thus, the avidity of the sulfides for xanthate should increase in the order: sphalerite C chalcopyrite 4 galena 4 pyrite, and the ease of depression response to the permanganate action should be in the same order. Depression of the sulfides in the system occurs primarily due to the removal of the collector ions by the permanganate ions to form manganese dioxide and dixanthogen according to the reaction: 3 M(RX)2 + 2 Mn04 + 4 H20 2 ? MnO2 + 3(RX-XR) + 3 M+2 8OH where M represents the metal ion, RX the xanthate ion and (RX-XR) the dixanthogen molecule. Results seem to indicate that the permanganate ions play a triple role in the system: (1) they convert xanthate ions into dixanthogen, (2) they further oxidize the mineral surface and (3) if present in excess, they may oxidize the xanthate beyond the dixanthogen stage with the formation of CO2, H20 and SO4. All sulfides, except for chalcopyrite, showed a depression response in the order predicted regardless of the order of addition of xanthate and permanganate reagents. Chalcopyrite did not depress as easily; this behavior may be due to the avidity of the colloidal MnO2 to adsorb Cu+2 ions on its surface, this would destabilize the colloid making it coalesce with the formation of a layer of precipitated MnO2 on the surface of the mineral. The presence of this layer would prevent further action of the permanganate ions on chalcopyrite.

Jan 1, 1970