Search Documents

By R. W. Brock

This subject is too broad and comprehensive to be dealt with adequately and authoritatively in this paper. It calls for the knowledge and experience of many men, but the results from such collaborative effort would be of great value, particularly if similar reports of the principal mining districts of the world were made on a standardized basis so that conditions everywhere might be directly and accurately compared. In considering conditions affecting mining in British Columbia, unfavourable as well as favourable factors must be taken into account. The unfavourable are apt to loom large and to be exaggerated rather than minimized; for it is human nature to see the blackness of the cloud rather than the silver lining; to think that one's own undertaking is beset with peculiar difficulties, and to attribute lack of greater success to out-side causes rather than to personal shortcomings. It should be recognized, however, that there is no country where the conditions for mining are ideal. The ideal mining country is the product of imagination, invested with every favourable condition found anywhere, but with none of the unfavourable conditions that are always present in reality. So if British Columbia has some handicaps to the industry, it is in good company. What is important is that the advantages compensate for the disadvantages, that the balance will compare favorably with that of competing states, for mining, like every other industry is competitive, and the cost of one's product must have a definite relationship to its price in the world's market.

Jan 1, 1924

By J. G. Donaldson

Cobalt-tungsten binary deposits were formed in laboratory experiments by hydrogen reduction of the anhydrous mixed vapors of cobaltous chloride and tungsten hexachloride. The materials were sublimed in seperately heated zones of reaction tube and were transported in a stream of purified helium into the deposition section of the tube where the chloride gases were reduced to metal by a countercurrent flow of hydrogen. Heattreating of the near stoichiometric binary metallic deposits converted nearly all to the intermetallic compound Co3W, however, small quantities of both cobalt and tungsten remained. Mechanical tests showed that the tensile strength of heat-treated 75 percent cobalt-25 percent tungsten deposits was twice as high as that of similarly treated deposits of cobalt.

Jan 1, 1965

By S. F. Shaw

Fox some time it has been more or less recognized within the industry that a scientific control of flowing wells would result in increased production and a greater ultimate recovery of oil. About two years ago it was proposed by the writer that this control should follow principles worked out by him while handling large air-life operations. In the case of wells that had ceased to flow where a large quantity of liquid was present, the use of these principles would result in a large increase of production by using compressed air or gas to flow the well; in the case of a well flowing naturally it would take the form of controlling the gas associated with the oil, resulting either in immediate increase of production or in a reduction of the gas consumed per barrel of oil, and in both cases would result in a greater ultimate recovery from the sand. The Roxana Petroleum Corp., appreciating the advantages to be obtained by a scientific application of the principles of the air lift to oil wells, recently engaged, for a limited time, the services of the writer to work out some of the problems involved. The work was carried out at Braman, Garber and Tonkawa in Oklahoma, and at Oxford in Kansas. Following some suggestions of the writer a well was also equipped by the Roxana company at Smackover by A. S. Field.

Jan 11, 1926

By A. -I. Abenhaim, I. Sasu, C. Perron, I. Mantegh, S. Larose

Manufacturing long shafts, such as those used in turbine engines, normally involves with drilling inside them in order to take the excessive mass out. Concentricity between the shaft axis and that of the drilled hole is very crucial as it impacts the mass distribution around the axis of rotation. It is important that the shaft mass be well balanced around the central axis in order to minimise the centrifugal forces on the bearings and supporting structure as well as any unwanted vibrations. The eccentricity problem, mostly in long shafts, comes due to machining limitations. It is difficult in long shafts to maintain the concentricity tolerances while drilling inside the shaft. In this work, we address the problem of correcting this eccentricity problem, i.e., when the axis of the inside hole deviates from the central axis. The presented work is based on a threepoint bending method and investigates its effect on the residual stresses and plasticity regions induced on the shaft. A full finite element model is presented that can used to design the solution parameters (bending load, location, etc.) and predict the effect. Limited experimental results are also presented to validate the finite element modelling.

Jan 1, 2006

By D. R. Taylor

The use of clay granules as carriers for pesticides dates from the early 1940's and by the present day represents a business conservatively estimated at between 200 -300 thousand tons / year in the U.S. alone. Aside from economic and specific target pest efficacy advantages, the use of clay granules as pesticide carriers also delivers a number of environmental benefits which will be reviewed. Topics to be discussed will include: I) drift control (versus liquid sprays), 2) mobility (in the environment), 3) worker safety, and 4) transportation (spill) safety.

Jan 1, 1999

By R. G. Kidel, S. C. Doming

The project has shown that it is feasible for a junior company to reopen a narrow vein-style gold mine and successfully take it into production. An intimate understanding of the mineralisation and a flexible approach to mining are crucial, as are stringent cost control and efforts to keep overheads low. The project has confirmed the geological complexity of the Main Lodes, which consist of highly sheared quartz-sulphide infill in strongly sericitised granodiorite. The existence of discrete high-grade zones within the Hangingwall Lodes has also been confirmed. Broad low-grade zones continue to be recognised and require the local application of bulk longhole mining methods. The initial mine plan called for predominantly longhole stoping, but adverse ground conditions have meant that a switch to air-leg mining has produced higher run-of-mine grades. The excess capacity at the processing plant can best be used by batch processing, with its reduced maintenance requirements

Jun 21, 1905

By R. R. Montigny

A brief description is given of the history, location and geology of the Granisle Copper Limited operation on Copper I land in Babine Lake. Detailed information is given with regard to pit design, planning, drilling, blasting, excavation and haulage. Equipment maintenance and mining costs are also presented.

Jan 1, 1971

By Takefumi Takuma, Tsunenobu Nozaki, Masashi Nagano

Using sheet piles and pipe piles for permanent earth retaining is one of the most economical methods for constructing basement walls since they can also work as temporary shoring during construction. A major mixed-use redevelopment project in the UK, encompassing two to three large city blocks, utilized both sheet and pipe pile walls for a two-level subterranean parking structure. The 290m (950ft) x 100m (330ft) basement’s steel walls were designed to temporarily support excavation during construction and eventually to become a load carrying permanent structure in order to expedite the construction process and to achieve cost reduction. Two types of press-in piling machines, one for sheet piles and the other for pipe piles, were used for the job because of their abilities to press in sheet and pipe piles within tight tolerances for finished walls, for difficult installation conditions with very hard soil, and for its very low noise and practically zero-vibration operation; an essential factor for the job in close proximity to other businesses and residents. BACKGROUND Steel sheet pile and pipe piles have been used for many purposes including earth retaining. They are produced at steel mills and spirally welded at a fabrication yard to their corresponding specifications under strict quality control measures. Therefore, they can form highly reliable walls to its design capacity with proper installations. Their advantages as underground walls are:  They can form a high level of water cut-off function with their interlocks sealed by welding or with hydrophilic materials. See Figure 1 for a few examples for a sheet pile application.  They can carry vertical loading in addition to horizontal load and bending moment.  They can be a self-standing and temporary/permanent wall with flexible design and construction processes; bottom-up, top-down or hybrid sequences can be chosen per the project’s needs.  They can form a thinner wall than other wall types, creating larger inner space. See Figure 2.

Jan 1, 2019

By P Khalkho, M Singh

Rock masses when subjected to uniaxial or triaxial cyclic loading (eg in hydraulic running tunnels, during retrieval and injection of oil and gas from storage underground caverns and haulage roads), the material has a tendency to fail in fatigue. In order to design safe and reliable underground structures, the determination of brittleness under such loading conditions becomes a pre-requisite. Brittleness influences strongly the failure process and makes the rock mass behaviour complex under different tunnelling and mining activities. Brittleness Index is a term to quantify the brittleness feature of a specimen. In the present study, an attempt has been made to quantify the brittleness of jointed specimens using different brittleness criteria. The joints of the model jointed specimens were oriented at an angle of θ=15° normal to the loading direction, each having three different JRC’s=2–4, 12–14 and 14–16. The specimens were tested under triaxial conditions in incremental complete cyclic test scheme performed at displacement-controlled mode. Different brittleness criteria were used ie stress-strain dependent brittleness index, Young Modulus approach and energy-balance based mechanism. It was observed that energy-balance based mechanism which consider the post failure behaviour is more descriptive to reflect the whole variation of brittleness from sheer brittleness to ductility.

Nov 29, 2022

By G. Bonifazi

Mining activities belong to human history, they are lost in the mists of time. They usually impact on large portions of the territory, both directly (exploitation areas and logistic activities directly related to exploitation) and indirectly (exploited material handling, processing and storage areas). As a result, at the end of mine life cycle, dismissed areas usually cannot be directly re-utilized without efficient and well addressed rehabilitation actions. Main goal of the proposed approach was to analyze the results obtained when a set of procedures, based on the collection and the analysis of remote sensed data, is developed to evaluate the effect of rehabilitation of land contaminated by extractive industry activities and to perform a monitoring and registration of the environmental impact of such operations by the application and the integration of modern information technologies, as Earth Observation (EO) and Geographic Information Systems (GIS). The study was developed in the framework of the EU-Asia program of the European union (EXTRACT-IT Project-Contract No: CN/ASIA IT&C/006 (89870): Application of Information Technologies for the sustainable management of Extractive industry activities) and it was addressed to three different dismissed mine areas in India, Thailand and China, respectively. The results, in terms of methodologies selected, strategies applied and results obtained, are described with particular reference to Fuxin coal mine area in China.

Jan 1, 2014

By Shaw Bill

The paper describes of the JORC Code in terms its background working environment and reasons for success, and provides references to papers which cover the subject in more detail. It then discusses the two major developments in Australasian reporting standards in the last two years: the revision of the 1999 Code, and the introduction in early 2003 of the “ROPO” (Recognised Overseas Professional Organisation) initiative. The purpose of the JORC Code is to provide a minimum standard for reporting of Exploration Results, Mineral Resources and Ore Reserves in Australasia, and to ensure that public reports on these matters contain all the information which investors and their advisers would reasonably require for the purpose of making a balanced judgement regarding the results and estimates being reported.

Apr 22, 2003

By S. H. Chauvenet

Jan 1, 1882

By J. E. Nesset

The bubble size, together with the gas rate, determines the bubble surface area flux in flotation machines and, therefore, impacts directly on the kinetics of flotation. Understanding the variables that influence bubble size is one of the keys to understanding flotation recovery. Surprisingly, these relationships are poorly understood, largely due to the difficulties associated with gas dispersion measurements in industrial environments. The McGill gas dispersion sensors (bubble size, gas rate, gas holdup) are capable of reliably making such measurements. This paper reports on a study, using the McGill sensors in a 0.8 m3 Metso RCSTM pilot cell, which investigated the effect on bubble size of frother type and concentration, gas rate, temperature and rotor speed. A Denver laboratory cell was used to investigate the effect of elevation above sea level. Frother concentration proved to have the predominant influence on bubble size, and the effect of frother type can be normalised as a function of the critical coalescence concentration (CCC). Measurements made at many plant sites worldwide are compared to the model developed using the Metso RCSTM unit.

Jan 1, 2007

By Agbo Chima

Low-lying sections of open-pit mines accumulate water, especially during the rainy seasons, preventing access to resource-bearing areas. To sustain mining operations, the water must be lifted out of the flooded pits at a high flow rate using pumps. These pumps need to be mobile so that they can be removed during drill-and-blast operations. Most mobile pumps rely on diesel engines with high maintenance requirements. A special pump design was developed to address the unique needs of open-pit mining while making the dewatering process more sustainable. Using the target flow rate and head data, an efficient pump was designed, encased, and deployed in the open pit. A variable speed drive (VSD) was installed in a protective skid so that the pump could be tuned to match the preferred flow rate at any point during its operation. This system was tied to the national electrical grid instead of being powered by diesel pumps, which reduced the carbon intensity per kilowatt-hour. The high availability, low maintenance requirement, and greater reliability reduced the use of spare parts, the fuel consumption, and the logistics associated with operating the pump. This further reduced the carbon footprint of the dewatering process. This paper provides some of the two-year performance metrics for a deployment in West Africa. With a focus on availability, maintenance costs, average cost per volume lifted, and carbon footprint, this encased pump system is compared to the diesel-driven pumps that it aims to replace.

Jan 1, 2023

By Larry A. Haas

The U.S. Bureau of Mines is investigating ways of enhancing the high-temperature softening-melting (HTSM) properties of domestic taconite pellets. These properties, which are important for determining the performance of pellets in blast furnaces, include pellet bed contraction, pressure drop, S-value (area under the pressure-temperature curve), and softening and metal-slag drainout temperatures. Experiments showed that HTSM properties were related to the physiochemical properties (fired strengths and reducibilities) of pellets containing different levels of limestone and dolomite flux. Flux additions resulted in slightly lower green and fired pellet strengths, but improved metallurgical properties, such as reducibility. The influence of reduction conditions on HTSM properties was evaluated by varying the pellet metallization starting temperature and the carbon monoxide content of the CO-N2 gas mixture. HTSM property change was more sensitive to flux addition levels when metallization was initiated at 1,100° C with 20 pct CO in the gas stream. The S-value and the metal-slag drainout temperature were found to be the best criteria for characterizing HTSM properties. The optimum flux addition level was about 8 pct (4 pct dolomite, 4 pct limestone) or a basicity of about 1. At higher flux levels, a higher metal-slag drainout temperature was obtained.

Jan 1, 2010

By Stein Tore Johansen, Fionn Iversen, Jon Arne Bakken

"A new marker chain front tracking method is used for modelling the meniscus movement during DC casting of aluminium ingots. Modifications have been made to an earlier method developed by Popinet and Zaleski [12] to adapt the model for simulations of meniscus dynamics in the casting process.Initial casting simulations show that wetting conditions in the mould greatly influence the meniscus stability. Controlling the wetting conditions seems to be important for improving the cast ingot surface quality.IntroductionIn conventional direct chill (DC) hot top casting of aluminium extrusion ingot with gas-slip poor surface quality of the cast ingot can be a problem. In the worst cases pronounced surface wrinkling occurs coupled with periodic zones of reduced grain size, macrosegregation and exudation at the surface. The observed surface irregularities are believed to be linked to Periodic surface oscillations or folding of the meniscus resulting in varying solidification conditions.The focus of this work is to gain a better understanding of the dynamics of the meniscus and the influence it has on the finished cast ingot surface through numerical simulations of meniscus movement during the casting process.A two phase marker chain front tracking technique[12] using cubic spline surface reconstruction is applied for modelling the meniscus movement. The advantage of this type of model is its accuracy in the calculation of surface tension forces. Also the wetting can be implemented directly as a boundary condition on the surface spline function. The method is applied in the FLUENT solver, which is based on a finite volume method using the SIMPLE algorithm."

Jan 1, 2001

By Peter Babik

"Cable TV networks are extensively used throughout Canada for TV signal distribution. Mobile/portable radio communications are also used extensively throughout all sectors of industry. There are numerous manufacturer supplying these industries with a wide variety of equipment and accessories.IAL's underground radio communications system combines the techniques of cable TV and mobile radio to produce a flexible communications system with most of the advantages of both systems. Standard off-the-shelf mobile, portable, base-station and repeater equipment can be used. The equipment may need modification to be customized to particular end user requirements, but does not require a complete new unit redesign. Likewise, the cable TV distribution equipment is off the-shelf, with some items requiring modification for underground system application.Radio communications can be provided wherever the cable system is extended. Where traffic or type of activity warrants it, multiple radio channels can be provided on the same cable. Certain radio channels could also be used with data channels for control or supervision of remote equipment or environmental conditions. In addition, the same cable can be used to distribute or monitor signals from remote TV cameras in selected or dangerous areas. The system can be interfaced to a telephone system, if required, to provide extended communications to above-ground workshops, offices, medical stations or even hospitals and other emergency services.IntroductionReliable communications among personnel throughout an underground mine area have long been the dream and goal of various mine operations personnel. The system to be described was designed to meet this objective."

Jan 1, 1983

By A. L. Jones

The subject assigned to me of "The Power" Problem of the Mine" is so broad that I have decided to confine myself to the question of the power supply itself, rather than the application of electricity throughout the property. We will look over certain economic aspects of the problem, particularly in the way it affects the mine manager or executive and his attitude toward the power plant. The accepted method of power application to the mine is by electric power, and the experience of each of you is that the job is never complete as you are always undertaking some further electrification which necessitates the stiffing up the power house to care for the additional load. The mine executive, then, is wrestling almost continuously with the problem of his power plant. Either it is overloaded and must be enlarged and rebuilt; or its operating costs are excessive; or it breaks down and limits coal output; or some one wants to sell new and improved machinery, until the manager almost hates the thought of such a restless part of his property. If he purchases power, every day new uses for it seems to be found. In many ways this unrest is due to short-sighted policy toward the problem, and the tendency when the problem of extension has to be met, to dispose of it in the cheapest way and without thought as to where the future is leading. The day when each opening had its own boiler plant, steam hoist, steam driven fans, steam pumps, steam loaders, etc., seems to be far behind us. The recognized method of power distribution today is by electric power, except for rather limited applications of compressed air; most of which is electrically compressed. During fifteen years contact with mines of Colorado and Wyoming the writer has seen nearly every mine power house double or triple in capacity or abandoned in favor of purchased power, worn. out and inefficient machinery thrown out, isolated boiler plants dropped, seam pumping at great depth changed to electric drive, all resulting in greatly reduced labor and fuel costs. Power costs, which in such isolated plants were considered normal, would be unthinkable today. One property where the main power supply was by compressed air from steam driven com¬pressors used under boilers 8.35 per cent of all the coal mined. The cost of power was 12 1/2 cents per ton of coal mined. Another property of four openings, each with its own boiler plant and usual equipment of hoists, pumps, etc., had a power cost of 10.3 cents for each ton mined; and these were days when you did not get very high prices for coal. Another property operating two mines mostly by steam used 11.1 per cent of the coal output under their own boilers and the power cost was 19.45 cents for each ton mined. Each of these properties is now electrified and power costs are from 3 to 4 cents per ton, and the fuel burned runs from 1 to 2 per cent of the output. With the broadening market and high prices for slack coal and the high prices for labor in boiler and engine rooms, the cost of steam is reaching a high figure, and efforts must be made to keep this down, by more efficient steam production and by utilizing this steam in better machinery which will increase the work done by each pound of steam. It must not be overlooked either, that the plant which is very wasteful of fuel is usually a pretty old one and one far from reliable. In a general way the more efficient the plant, the greater its reliability. Ample and reliable power supply means ability to get out coal when there is a market. The increasing use of purchased power is largely due to changing conditions which are tending constantly to push up the cost of power, unless the most efficient machinery is used and large scale production possible. The

Jan 1, 1923

By S. H. Lorain

This paper is one of a series on mining methods and costs being published by the U. S. Bureau of Mines. The operations of the Quartz Hill Mining Co., near Dewey, Mont., afford an interesting example of the cost of mining small bodies of direct shipping ore; they also illustrate the effect of the unavoidable periods of unusually high exploration and development costs in this type of mining upon the cost per ton of producing ore. The importance of skilled geological guidance and the necessity of avoiding unnecessary overhead and capital expense at small mines are shown. Operating conditions at Quartz Hill are typical of those in many other mining districts of southwestern Montana. It is believed that the costs presented here may be of value in the preliminary estimation of costs to be expected by conservative operators under similar conditions elsewhere. The information contained in this paper was obtained during a visit to the Quartz Hill mine in August 1936.

Jan 1, 1937

By J. A. Herbst

In spite of potential theoretical and economic advantages of large-diameter ball mills, many manufacturers elect not to build these mills owing to what is perceived as an excessively large design risk. This risk results from the fact that traditional predictions for mill-scale-up to large diameters are not always accurate. It is apparent that alternative methods of analysis and scale-up are required. Recent studies have shown that detailed population balance models which account for important grinding subprocesses, i.e., grinding kinetics, material transport, and classification, are capable of predicting the performance of small- and intermediate diameter mills (up to 4.3 m (14 ft)) from small-scale batch tests. These same models are used in the current study to predict the performance of a "borderline" large ball mill (4.7x5.5 m) at Asarco's Sacaton operation, a ball mill (5.0x5.8 m) at Kennecott's Chino operation, and one of the world's largest ball mills (5.5x6.1 m), at Cities Service Pinto Valley operation. Model parameters required for scale-up have been estimated in a 380-mm diameter batch mill. Predictions are compared with the results of detailed plant sampling in the three plants. For the Sacaton and Chino operations, the error of the predictions was found to be less than 2.5%, while the corresponding error for the Pinto Valley operation was less than 2.7%. It is concluded that proper representation of the major subprocesses of grinding in the model equation is the key to achieving accurate scale-up. Of special importance is the need to account for the size distribution of the grinding media and the influence of the size distribution environment in the mill on grinding kinetics.

Jan 1, 1983