Search Documents

By Michael Rieber

The increase in f.o.b. mine prices of coal from $5/ton to over $18/ton in five years [1] has increased the significance of transportation costs. Coals produced in the vicinity of the consumer bear a much lower transport cost than those produced in the west. This differential may be used for flue gas desulfurization, other cleaning, or further processing of local coals. To the extent that western coals are cheaper to produce and have a lower sulfur content, they offset the locational disadvantage. To the extent that they have a lower heating value, the disadvantage is exercabated. Given the other conditions, an accurate analysis of transport costs will help suggest the location of coal mining and the moue of transport both transport costs and tariffs have risen. Together they have increased delivered coal prices, altered the balance between the use of coal and other fuels, helped to alter the location of mining activity, and put pressure on consumers to examine the cost effectiveness of alternative transport modes. Transportation options for long distance coal movements include rail, barge, pipeline, and EHV transmission lines. A summary of system parameters is shown in Table 2.1. Barge transport, pneumatic and slurry pipelines are discussed elsewhere in this report. Together with EHV, they have been the subject of previous studies [2,3,4]. Slurry pipelines have been shown to be especially useful where rails are not available [2] but the technical problems of dewatering, handling, and utilization of lines [5] remain unresolved. They are discussed in Section 3. Barge transportation depends on the location of the mine and consumer with respect to the waterway system. One drawback of barge shipment is interruptions due to winter, and low or high water conditions. Mine mouth power generation followed by EHV transmission of over 500 miles has been shown to be the most expensive means of delivering an equivalent amount of energy to consumers [2].

Jan 1, 1977

By Stephen G. Downs

PCF?, or Penetrating Cone Fracture, is a propellant-based technique for rock excavation, which has significant potential for the mechanization of narrow-vein mining. The technique is currently being developed for use in the narrow-vein flat-dipping gold and platinum deposits in South Africa in conjunction with major mining companies. The technique is also applicable to steeply dipping vein deposits, such as those found in North America, Australia and elsewhere. The implementation of PCF? in South Africa to date is reviewed and plans for the introduction of PCF? excavation in other areas are highlighted.

Oct 1, 2001

By P. Barnes

Exact accounts hare been kept of the cost of these chimneys, and it may he a matter of some possible interest. that the plans and details of cost should be laid before the Institute. The statement of cost herewith submitted does not give minute particulars of the weights or quantities of material used, although these are noted upon the company's books.

By Richard J. Bielicki

The possibility of replacing the brattice cloth closest to the coal mine working face with an air curtain mounted on top of a continuous-mining machine or with a diffuser fan was explored by the Bureau of Mines. Preliminary tests conducted at a full-scale model working face with the brattice end set at 18 feet showed that the air curtain improved face ventilation only slightly and was not nearly as effective as placing the brattice at 10 feet. A 2,000-ft3/min diffuser was more effective than the air curtain. It is concluded that the air curtain probably could not function as a line brattice extension, although the diffuser fan may have some potential.

Jan 1, 1975

By Jaeheon Lee, Jai‑Won Byeon, Junmo Ahn, Jun‑Jae Lee, Eun‑Woo Kim, Yoo‑Jin Kim, Jiajia Wu, Jae‑Yeon Kim

Growing demand for valuable battery materials and environmental issues from battery disposal make the recycling of spent lithium-ion batteries (LIBs) essential. Specifically, the green approaches using organic reagents have garnered many attentions for battery recycling. In this study, a synergetic organic leaching system using methanesulfonic acid (MSA) of strong organic acid and citric acid (CA) with good chelating ability was investigated to extract valuable metals from LiCoO2. Hydrogen peroxide was used as a reducing agent to enhance leaching kinetics. Cobalt extraction of 98% and lithium extraction of 97 % were achieved in the optimized condition; 2.4M MSA, 1.6M CA, 1.0 vol% H2O2, S/L ratio 80 g/L, 85 °C, and 1 h. The optimal leaching condition of the MSA-CA mixed leaching system exhibited good applicability to various cathode scraps, such as LiCoO2, LiNixMnyCo1- x-yO2, and LiNixCoyO2. The dissolved Co and Li ions in the MSA-CA leachate were selectively recovered with high recovery efficiencies of 99 % and 97 % as Co3O4 and Li3PO4, respectively. The recovered Co3O4 and Li3PO4 were utilized to regenerate cathode materials. LiCoO2 and LiFePO4 were also synthesized through a solid-state reaction and hydrothermal method. The recycling process based on the MSA-CA-H2O2 synergetic leaching system was proposed, and it might be applied as a green and economical organic leaching system for the recycling of various types of spent LIBs.

Sep 20, 2023

By S Wangchai, D B. Hastie, P W. Wypych, A P. Grima

Industries that handle and process ‘dusty’ ores are facing increasingly difficult challenges to ensure sustainable operation and development. Most existing dust-control measures treat only the symptoms of dust generation and do not deal with the root cause/s of the problem. Many of these methods are also relatively inefficient in terms of controlling dust emissions. This paper summarises the various existing options available for dust control and some of their features, advantages and disadvantages. It then describes some of the new technologies that are being researched, developed and employed to minimise dust emissions by addressing dustability or dustiness and the dust generation mechanisms found in industry. Recent research results and case studies are presented to demonstrate some interesting findings obtained from this work. With improved understanding and modelling of dust generation mechanisms and bulk material dustiness, it is possible to achieve a step-change improvement in the design, troubleshooting and application of more efficient dust-control technologies.CITATION:Wypych, P W, Hastie, D B, Wangchai, S and Grima, A P, 2015. Research and application of new dust control technologies for the iron ore industry, in Proceedings Iron Ore 2015, pp 529–536 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By L. W. Higley

Procedures were developed for reclaiming high-temperature alloy scrap in the form of standard cobalt-base alloy. A cobalt-base, multicomponent, high- temperature alloy, such as S-816, can be successfully melted from scrap, and its specified chemical composition can be retained. Induction furnace melting in a controlled atmosphere was used to obtain ingots that were subsequently fabricated by impact forging to provide specimens for heat treatment and testing. Of the numerous metal elements in S-816 alloy, only small quantities of molybdenum were lost in the melting operation as finally developed. Test results indicated that the scrap material, after melting, forging, and heat treatment, was equivalent in room-temperature tensile strength, in high-temperature creep and stress-rupture properties, and in chemical composition to commercially produced S-816 alloy made from virgin material.

Jan 1, 1963

International tenders for contract mining opportunities require the Contractor to make an assessment of risk for an operation with a life span of up to twenty-five years usually based on data made available by the Client. This paper seeks to address how the Contractor assesses the data and quantifies the risks associated with the project. The areas of risk are common to most projects, but in the--Lontractor's case, risk assessment is carried out on the Client's data base and within a compressed time frame of usually less than six months. Incorporation of that risk assessment into the contract documentation is also discussed. Practical examples are given in a number of areas.

Jan 1, 1986

By K. Noda

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. started its operation adopting the Flash Smelting Furnace with Furnace Electrodes (FSFE). Thereafter, it developed a coke combustion technology based on C() concentration control, which made possible a low cost and high productivity operation without using electrodes. However, increase of treated concentrates and upgrading of matte grade for production expansion started to cause difficulties in operation control with then existing operation control system. This paper outlines recent improvements for stable operation of the Tamano Type Flash Smelting Furnace (T-FSF), such as computer aided operation guide system.

Jan 1, 2001

By C R. Fountain, R J. Sinclair

The zinc industry is dominated by the electrolytic zinc (EZ) process. The EZ process has a low tolerance for impurities, resulting in tight concentrate specifications. Many mining companies sacrifice zinc recovery in order to meet smelter specifications. Some have ore-bodies that cannot be economically developed because too much metal has to be sacrificed, or it is just not possible to meet the specification. The BUKA Zinc Process (BZP) has been developed as a method of producing high-quality zinc from a wide range of concentrates. It can have lower capital and operating costs than the conventional zinc and lead production routes. Advantages accrue from increases in metal recovery during concentrating, smelting and refining; the elimination of most of the capital and operating costs associated with lead smelting; reduced transport costs; lower zinc refining costs; reduced refinery residue disposal costs; and reduced future environmental liabilities. This paper describes results of testwork that has been undertaken to demonstrate the viability of the BZP on both test rig and laboratory-bench scale.

Jan 1, 1998

By Douglas W. Barr

If some of you have been through the long hot summer in the southwest, you may find it refreshing to turn your thoughts to the wintertime problems of mineral processing in the northern climates. The purpose of this paper is to point out some of the ways in which heat is gained or lost in the tailing basin operation and the problems that can result if too much heat is lost.

Jan 1, 1980

By Gibson J.

Written discussion contributions to the paper presented at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 12th February 1916, with Mr. T.Y. Greener, President, in the chair, comprise comments by Kilpatrick W.M., Routledge W.H., Watson J. and Smith W., along with the author's reply. Also briefly noted are the demonstration of two pieces of equipment, an incline chock and a cage arrestor

Dec 1, 1916

By Peter M. Power

A microscopic study was made of a series of simultaneous slag and metal samples taken from a low carbon basic open hearth heat. An attempt was made to identify the various micro-constituents found. As the various impurities in the bath are oxidized, the metal structure changes from that of high-phosphorus white cast iron to that of low.-carbon steel. A detailed study of phosphorus distribution is included. The acid run-off slag has an .acicular orthosilicate structure which changes on 'shape-up' to a very basic tri-calcium silicate and calciuim ferrite structure. Many unidentified minor constituents are present in the slags. Though metallography will never replace chemic.al analysis of the bath, the microsopic study of polished slags has some promise of being useful in slag control work.

Jan 1, 1956

By Mafalda Arias

Most mining and mineral exploration companies? operate in remote locations, in Canada or internationally. Not knowing the cultural imprint of your team and the places where your company is active, may lead to problems. To set the foundation for a better world, it?s important to built trust and relationships inside your global team, within communities and together with stakeholders. Building the ?invisible asset? and developing intercultural awareness is an important part of leadership programs for geologists and engineers on your team, and should be a key component of your Corporate Social Responsibility initiatives. Why is culture important for mining and mineral corporations in their CSR initiatives? Because culture is the foundation of your organizational identity. Understanding the impact of identity, for an organization and for each individual, will provide a description of the experiences and values that affect every work placed interaction, with your clients, with colleagues, with suppliers, with the community of the host country. Each one of us sees and evaluates the world through our perceptions. Through these perceptions we give meaning; how we view and understand our reality which sets the tone for how relationships are built. This is what I call building the ?invisible asset?. Identity, experiences, values and beliefs are invisible commodities, locating them can be as difficult as finding a mine. But if they are not located, the commodity does not have value. Just like in the work we do in our industry. For example when you are working in an underground gold mine and the vein is lost, you keep on working and trying to find the vein; time passes, money is being used and no results. You decide to bring an expert on this type of deposits who gave you directions that allowed you to find the vein. To be a responsible citizen of the world and to set the foundation for a better world, it is imperative to go deep, as deep as your next drilling program, because only there and then, can you develop the cultural sensitivity and the ability to become an agent of change for responsible, sustainable and profitable businesses.

Oct 1, 2010

By Tassos Grammatikopoulos, Gary Pearse, Massoud Aghamirian, Charlotte Forstner, Stephen Mackie

"SGS Minerals Services (Lakefield, Ontario site) has conducted a number of developmental and pilot programs that examined methods for the beneficiation, extraction and recovery of lithium from a variety of spodumene containing hard rock sources. An overview of the beneficiation programs is presented separately by Aghamirian, Mohns, Grammatikopoulos, Imeson & Pearse (2011). The focus of this discussion will be the hydrometallurgical steps involved in producing a high grade lithium carbonate (Li2CO3) sample from the spodumene concentrate. SGS has applied the standard Li2CO3 hydrometallurgical flow sheet to a number of spodumene concentrates and has determined that all of these samples respond in a similar manner to the process and produce a final product having a Li2CO3 grade of >99.5%. The standard process is sufficiently robust to accommodate the observed variability in the concentrates that have been tested. Advantage of one spodumene deposit over another will thus be gained through process optimization and innovation. Optimization at the beneficiation stage and at the hydrometallurgical stage must be considered. Some aspects of the process optimization of the hydrometallurgical flow sheet will be presented.INTRODUCTION The current activity in the exploration, development, and mining of lithium based minerals is due in large part to the key role that this metal plays in the rechargeable battery industry (U.S. Geological Survey, 2011). Lithium battery technologies are widely applied in a range of portable electronic consumer products. The expanding development and production of hybrid and fully electric vehicles has contributed to the increased interest in finding and developing new lithium sources in order to meet the expected demand from the lithium battery industry. Lithium may be sourced from continental brines (sub-surface salars), hard rock minerals (pegmatite, spodumene), hectorite clay deposits, geothermal brines and oilfield brines. Currently the majority of the lithium products are produced from Li brines. The four major lithium producing countries are Chile, Australia, China, and Argentina (U.S. Geological Survey, 2009; Roskill, 2009). These countries accounted for 97.6% of the total lithium produced in 2010."

Jan 1, 2012

By F. J. Perzak

The Bureau of Mines conducted a study to develop a standard fire test for 5-gal containers used for storing combustible fluids in underground coal mines. A standard test method was developed which evaluates the performance of the container in a 4-min tray fire. Bureau investigators used the standard test method to evaluate several types of closed 5-gal plastic and metal cans in outdoor tests. Each can tested contained 1 gal of nonfire-resistant (NFR) hydraulic oil. A container failed the test if it lost its contents in any of seven trials. Contents spilled either as a result of thermal rupture or melting. Fewer than 10 pct of the metal containers failed this criterion, but all the plastic containers failed. The metal container failures were usual-ly due to tipping over during pressure relief, which spilled the NFR oil. Replacing the NFR oil in the container with kerosene resulted in failure of more than 30 pct of the metal containers. The standard tests and preliminary tests showed that plastic containers are not equivalent to metal containers in their ability to contain combustibles such as lubricants and greases in a fire. For solvents and lubricants more volatile than NFR hydraulic oil, approved metal safety containers are recommended.

Jan 1, 1985

By Oliver Bowles

This report covers the character, properties, origin, occurrence, and uses of the traprocks and describes briefly the methods and equipment employed in quarrying and preparing them for market. Production of traprock occupies an important place in industry. In 1960 the output in the form of crushed stone reached nearly 58 million tons valued at $87 million. Traprocks are also shaped into blocks of dimension stone for monuments, building construction and decoration, and specialized products such as surface plates.

Jan 1, 1963

By Oliver Bowles

This report covers the character, properties, origin, occurrence, and uses of the traprocks and describes briefly the methods and equipment employed in quarrying and preparing them for market. Production of traprock occupies an important place in industry. In 1960 the output in the form of crushed stone reached nearly 58 million tons valued at $87 million. Traprocks are also shaped into blocks of dimension stone for monuments, building construction and decoration, and specialized products such as surface plates.

Jan 1, 1963

By E. H. Illsley

This bibliography is the first report of a Bureau of Mines research project on thermoelectric materials. Interest in such research has increased because of recent success in the design of commercial products, including generators and refrigerators, using the principles of thermoelectricity. This success made possible by the discovery of semiconductors that have much higher [effincies] than the metals and alloys formerly studied. Thermoelectricity is a term that includes a large number of phenomena relating heat to electrical energy. However, the moat important applications arise from two effects discovered by Seebeck in 1822 and by Peltier in 1834. When pieces of two unlike materials are joined at their two ends to form a continuous circuit, both of these effects may be observed. If the two junctions are maintained at different temperatures, an electromotive force known as the Seebeck voltage is generated. If, on the other hand, a current is made to flow through the circuit, the junctions of the materials will be found to differ in temperature. This phenomenon is called the Peltier effect.

Jan 1, 1959

By Alexander S. Escalante, Luis R. Ramirez, Nelson A. Arostegui

Research, analyze, discuss, design, and build an electric oven to perform one of the quality control tests the fanel or common fulminers to determine what temperatures they can detonate at. Give practical applications, conclusions, recommendations and bibliography.

Feb 1, 2020